Error messages after upgrading kernel (devfs to udev) [SOL]
when installing the new kernel i got a message to change my menu.lst so it changed "/dev/discs/disc0/part3" to "/dev/hda3" (and nothing else) cause of udev instead of devfs.
after rebooting i get few error messages:
[after network start]
SIOCSIFADDR: No such device
eth0: unknown interface: No such device
SIOCSIFBRDADDR: No such device
etho0: unknwon interface: No such device
kjs wrote:I'm also having an issue after upgrading neither eth0 nor eth1 are showing up in /dev .... I think it's due to the switch from devfs to udev...
for the record - network interfaces never show up in /dev - they're not normal devices
edit: I guess I should provide some help...
ifconfig and "ifconfig -a" will list network devices (also in /proc/net somewhere). If you do not have a network device that means that your module is not properly loaded for that device.
This should have nothing to do with a devfs/udev switch and everything to do with a kernel upgrade.
Just for some more info, can you please report the output of:
· lsmod
· uname -r
· ls /lib/modules
· ifconfig -a
Similar Messages
-
Error message after upgrading to 7.3
i upgraded to iTunes 7.3 and i got a message that said something about some files were missing and i needed to uninstall and try again. i uninstalled it and now i can't even download iTunes. i can download but i can't do anything else. anybody else having this problem?
Yes, i had the same error message after upgrading to 7.3.
I am using windows XP - i went to the Control Panel -> Add/Remove Programs -> Scrolled to iTunes & clicked on Change (not Remove), then clicked Repair. It all works fine after that.
Search this forum - i hope you find a solution. -
I am getting this error message after upgrading to iOS5: "iTunes cannot sync apps to the iPad "ray's iPad" because the apps installed on the iPad could not be determined."
I wiped it out and restored from backup but I am still getting the same message.I uninstalled and reinstalled iTunes and that fixed it. Here are the specific instructions that I was given.
~~~
Try the following steps:
1. Go to Microsoft website to fix install and Unistall problems. Click "Run now" from Fix it to remove all iTunes & related installer files:
http://support.microsoft.com/mats/Program_Install_and_Uninstall
Be aware that Windows Installer CleanUp Utility will not remove the actual program from your computer. However, it will remove the installation files so that you can start the installation, upgrade, or uninstall over.
2. You should remove all instances of iTunes and the rest of the components listed below:
it may be necessary to remove all traces of iTunes, QuickTime, and related software components from your computer before reinstalling iTunes.
Use the Control Panel to uninstall iTunes and related software components in the following order:
iTunes
QuickTime
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support (iTunes 9 or later)
Follow the instructions from Apple article listed here: http://support.apple.com/kb/HT1923 to remove all components
3. Reboot your computer. Next, download iTunes from here:http://www.apple.com/itunes/download/ and install from scratch
~~~
Good Luck!
~R -
Error message after Upgraded from 2.53ghz (533 FSB) to 3.2ghz (HT)
Hi! everyone,
As you can see i'm a newbie on this board, however I've frequently visited here once in a while. Anyway, the problem I currently have after I upgraded my cpu from 2.53 ghz to 3.2ghz HT (Northwood) is that I not very often (few times so forth since monday) see this error message after reboot my pc :
***Message starts here***
A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this stop error restart your computer. If this message appears again, follow these step:
Run system diagnostic utility supplied by your hardware manufacturer. In particularly run a memory check and check for faulty or mismatched memory, try changing video adapters.
Disable or remove any newly installed hardware or drivers....etc.
Technical information
***STOP: 0x0000007F (0x00000008, 0xF7806d70, 0x00000000, 0x00000000)
....................................... ........etc.....
****Message ends here****
As i stated before I've never seen this message before the upgrade. So, here is my configurations:
BEFORE
875P NEO-LSR w/ BIOS v. 2.0
2.53ghz 512 FSB CPU
9500 Readon 128mb video card
Dual IDE HD 80gb & 160 gb (NON SATA)
1gb Dual channel memory (512mb on channel 1 - 512mb on channel 3) (KINGSTON pc2700 module)
CURRENT
857P NEO-LSR w/BIOS v. 2.0
3.2ghz 800 FSB 512mb (L2 cache) CPU
9500 Readon 128mb video card
Dual IDE HD 80gb & 160 gb (NON SATA)
1gb Dual channel memory (512mb stick on channel 1 - 512mb stick on channel 3) (KINGSTON pc2700 module) *
* may be this causes this error message because as I read it on the discription page of the 875P NEO-LSR that it will only support DUAL channel (PC3200 type) with HT CPU. So, i suspect this may cause the problem but I havent try to rearrange my memory to one channel (1 x 2) yet.
I will greatly appreciate it if someone in here who may has experienced it before or know what all this means. Please adviseThanks for your advise bejon2000.
Here is my situation, I just freshly installed Windows XP Pro w/SP2 prior to this cpu upgrade ...I did the os last weekend and upgraded the cpu the day or two after which is monday of this week. So, can I just do the BIOS update now with the os already inplaced ??? I assum the aswer is yes, however I just wanted to confirm before I do it, you know
I've SiSoftware Utilities 2004 installed on the system as well, and after I did the Performance Tune-Up in SiSoftware ...This is what I got
SiSoftware Sandra
Display on Screen
Device Type : Desktop/Notebook
System Summary
Analysing...
Tip 2546 : Large memory modules should be ECC/Parity.
Finished Successfully : Yes
****Mainboard Information
Analysing...
Power / Aux Temperature : 59.0°C / 138.2°F
Notice 224 : SMBIOS/DMI information may be inaccurate.
Tip 2505 : System does not support memory error detection. Some memory errors may go unnoticed.
Warning 2506 : System does not support memory error correction. System will stop if memory errors are found.
Tip 2511 : Some memory slots are free so the memory can be easily upgraded.
Tip 2546 : Large memory modules should be ECC/Parity.
Warning 2518 : Mainboard temperature is too high.
Finished Successfully : Yes
***CPU & BIOS Information
Analysing...
Tip 210 : Processor 1 : Mainboard supports faster CPUs, so the CPU can be upgraded when needed.
Notice 224 : Processor 1 : SMBIOS/DMI information may be inaccurate.
Notice 224 : System BIOS : SMBIOS/DMI information may be inaccurate.
Tip 212 : System BIOS : BIOS can be shadowed so check whether it is.
Tip 211 : System BIOS : BIOS is flash-able and socketed so it can be upgraded when needed.
Finised Successfully : Yes
APM & ACPI Information
Analysing...
Notice 224 : SMBIOS/DMI information may be inaccurate.
Finished Successfully : Yes
PCI, AGP, CardBus Bus(es) Information
Analysing...
Finished Successfully : Yes
Video System Information
Analysing...
Tip 319 : Primary Display Driver (display) : A refresh rate of at least 75Hz is recommended. Increase it if possible.
Tip 323 : Primary Display Driver (display) : Remove the desktop wallpaper to save memory and improve performance.
Tip 319 : RADEON 9500 (\\.\DISPLAY1) @ \\.\DISPLAY1 : A refresh rate of at least 75Hz is recommended. Increase it if possible.
Tip 323 : RADEON 9500 (\\.\DISPLAY1) @ \\.\DISPLAY1 : Remove the desktop wallpaper to save memory and improve performance.
Finished Successfully : Yes
Windows Memory Information
Analysing...
Finished Successfully : Yes
Drives Information
Analysing...
Warning : 1.44MB 3.5" (A:) : Cannot obtain drive information; check that a disk is in the drive and it is correctly formatted.
Warning : CD-ROM/DVD (F:) : Cannot obtain drive information; check that a disk is in the drive and it is correctly formatted.
Warning : Removable Drive (G:) : Cannot obtain drive information; check that a disk is in the drive and it is correctly formatted.
Tip 1821 : Removable Drive (H:) : Label (name) drive.
Finished Successfully : Yes
Ports Information
Analysing...
Warning : Communications Port (COM1) : Port in use. [5]
Finished Successfully : Yes
Keyboard Information
Analysing...
Finished Successfully : Yes
Mouse Information
Analysing...
Finished Successfully : Yes
Sound Card Information
Analysing...
Finished Successfully : Yes
Printer and Fax Information
Analysing...
Tip 402 : PaperPort Color : Print quality may have been set too low. Check settings.
Finished Successfully : Yes
MCI Devices Information
Analysing...
Finished Successfully : Yes
Windows Information
Analysing...
Tip 1300 : Enter your company name or "Home" instead of "Unknown".
Finished Successfully : Yes
WinSock Information
Analysing...
Finished Successfully : Yes
Processes Information
Analysing...
Tip 1601 : 6. tinhbuon0e - ********* - Winamp [Stopped] : Program consumes a large amount of memory.
Tip 1601 : Adobe Photoshop - [main.psd @ 90.9% (Layer 4, RGB/8)] : Program consumes a large amount of memory.
Tip 1601 : Adobe ImageReady : Program consumes a large amount of memory.
Finished Successfully : Yes
Modules Information
Analysing...
Finished Successfully : Yes
OLE Information
Analysing...
Finished Successfully : Yes
DirectX Information
Analysing...
Finished Successfully : Yes
Network Information
Analysing...
Finished Successfully : Yes
SCSI Information
Analysing...
Warning 2600 : WDC WD80 0JB-00CRA1 : SCSI version does not adhere to ANSI. Probably ATA/ATAPI device.
Warning 2600 : Maxtor 6 Y160P0 : SCSI version does not adhere to ANSI. Probably ATA/ATAPI device.
Warning 2600 : TOSHIBA DVD-ROM SD-M1712 : SCSI version does not adhere to ANSI. Probably ATA/ATAPI device.
Warning 2600 : PLEXTOR DVDR PX-716A : SCSI version does not adhere to ANSI. Probably ATA/ATAPI device.
Finished Successfully : Yes
Font Information
Analysing...
Finished Successfully : Yes
CMOS Information
Analysing...
Finished Successfully : Yes
OpenGL Video Information
Analysing...
Finished Successfully : Yes
Services Information
Analysing...
Tip 2130 : Alerter : Service may be disabled on Home/Professional OS version.
Tip 2130 : Error Reporting Service : Service may be disabled on Home/Professional OS version.
Tip 2130 : Help and Support : Service may be disabled on Home/Professional OS version.
Tip 2130 : Removable Storage : Service may be disabled on Home/Professional OS version.
Tip 2130 : IPSEC Services : Service may be disabled on Home/Professional OS version.
Tip 2130 : Remote Registry : Service may be disabled on Home/Professional OS version.
Tip 2130 : Secondary Logon : Service may be disabled on Home/Professional OS version.
Tip 2130 : Windows Image Acquisition (WIA) : Service may be disabled on Home/Professional OS version.
Tip 2130 : Distributed Link Tracking Client : Service may be disabled on Home/Professional OS version.
Finished Successfully : Yes
ATA/ATAPI Information
Analysing...
Warning 3100 : ATA device (fixed) : SMART not enabled; consider enabling for safety.
Warning 3103 : ATA device (fixed) : Acoustic Management enabled. Peformance may be impaired.
Finished Successfully : Yes
Data Sources Information
Analysing...
Error : Could not connect to the database. : Could not connect to the database.
Error : Could not connect to the database. : Could not connect to the database.
Error : Could not connect to the database. : Could not connect to the database.
Error : Could not connect to the database. : Could not connect to the database.
Tip 3001 : ODBC Information : ODBC driver support old; should support ODBC 3.52 or later.
Error : Tables/Views : No tables/views found.
Error : Procedures/Functions : No procedures/functions found.
Finished Successfully : Yes
Hardware IRQ Settings
Analysing...
Finished Successfully : Yes
DMA Settings
Analysing...
Finished Successfully : Yes
I/O Settings
Analysing...
Finished Successfully : Yes
Memory Resources
Analysing...
Finished Successfully : Yes
Plug & Play Enumerator
Analysing...
Finished Successfully : Yes
Performance Tune-up Wizard
Finished Successfully : Yes
There are actually some notices on MAINBOARD INFORMATION & CPU & BIOS INFORMATION, however I'm not sure what exactly they mean though.
******UPDATED*****
here is the last part of the error that i described in my first post, I just saw it again right now
****STOP: 0x.......
**** sysaudio.sys - Address F6EAA481 base at F6EA7000, Datestamp 41107F1a
Beginning dump of physical memory
Dumping physical memory to disk: (counting from 1 to 99 then it shut down the computer) -
[Solved] xorg server & keyboard conf error messages after upgrade
I ran my daily upgrade (today was big, from FF to the kernel to xorg) and I was not able to login on GDM afterwards.
It's weird. The X server will start, and so will the GDM login screen. But entering the password will result in a GDM crash (I later found out that KDM and SLIM have the same issue; KDM not starting and SLIM refusing the keyboard input). So after starting an alternate console and trying to start x (startx), I have this error message:
"Th e XKEYBOARDMAP keymap compiler (xbcomp) reports:
Error: Cannot close "/tmp/server-0.xkm" properly (not enough space?)
Output file "/tmp/server-0.xkm" removed
Errors from xkbcomp are not fatal to the X server
XKB: Failed to compile keymap
Keyboard initialization failed. This could be a missing or incorrect setup of xkeyboard-config.
Fatal server error:
Failed to activate core devices "
I have been fiddling with the keyboard config on xorg.conf but I'm not sure I'm getting anywhere. Also, I downgraded the xorg-server and xkeyboard config packages just to be sure.
Any clue?
Thanks!
Last edited by southerncross (2012-07-24 15:46:38)Well... seems I didn't have any answer on this. I fiddled a bit more but I have to say that I really came to wits' end at this stage. A couple of observations though:
* I don't really understand this notion of a keyboard issue. My keyboard and its layout work properly but I will not be able to login regardless of login through GDM, KDM or Slim. Yet it's worth noting that in the case of GDM and SLIM the X server starts; I see the graphical interface, I click, etc. but when I type the trouble starts.
* I tried to check my xsessions-errors file. The file is really big under a frame buffer, and it wasn't clear to me, but I found strange that the log was reporting all sorts of attempts to start KDE. I don't exactly know what's going on.
If anybody has any clue, let me know... It's becoming very frustrating.
Thanks! -
Several attempts to upgrade to iTunes 11 have failed. After an upgrade to 11 the error message reads: "iTunes has detected a problem with your audio configuration. Audio/Video playback may not operate properly." At this point--after the upgrade to iTunes 11--my PC running Windows XP loses audio playback for all functions--in iTunes, in the browser and the volume icon disappears from the System Tray. Only by removing iTunes 11, and then using System Restore to turn back the OS settings can I return the PC to normal functioning.
I did that. I reinstalled iTunes 10.5. Everything seemed fine, but when I try to plug in and copy a CD to my iPhone 4S an error message reads roughly: 'iPhone 4S requires iTunes 10.5 or higher to work.'
What might be the problem with my audio configuration?
Why doesn't my iPhone 4S work with iTunes 10.5? It used to work with iTunes 10.5.
Please advise.
epThis forum is for questions about iTunes U, Apple's service for colleges and universities to post educational material in the iTunes Store. You'll be most likely to get help with this issue if you ask in the general iTunes for Windows forums.
Regards. -
Yesterday I upgraded my iPad Air from 7.1.2 to 8.3 after holding off upgrading until now. Before the upgrade I backed up the iPad without any problems but since the upgrade I can't back up the iPad – it goes to step 2 of 4 and stays there for ages, and then I get a pop up box saying "iTunes could not back up the iPad "... iPad" because the iPad disconnected."
I've just tried setting up iTunes on another PC and backing up the iPad to this iTunes and got the same error message so it's not the iTunes setup on either computer (Windows 7 PCs).
Everything I've tried so far seems to be working on the iPad but I can't do any backups.
Any suggestions on what else to try will be much appreciated.Sometimes resetting the iPad system helps. Did you try that? If not, try it. Hold down on the sleep and home buttons at the same time for about 10 seconds until the Apple logo appears on the screen, then let go of the buttons and let the iPad start up. Then try to backup again.
-
I got the following message when trying to telnet to our switch after upgrading from 3.3(4a) to 3.3(5b) on our MDS 9120 (after supplying my credentials):
telnet login is temporarily not available as startup configuration is being applied.
This was after the switch reloaded after issuing the install all command. Since I couldn't telnet I logged in via the console and noticed there was no startup config but the running config was there and correct. After about 30 minutes with the switch being up everything was back to normal. The startup config was there and I all services were up and running.
Has anyone experienced something like this before with an upgrade? During all my past upgrades after the reload (single supervisor switches) the switch was up and running just fine. Something a new to this upgrade for me is that this switch doesn't have an active mgmt interface, we reach this switch using IPFC (create ip interfaces on vsans that are merged between switches).Everything is currently set to the defualt levels.
show logging level
Facility Default Severity Current Session Severity
aaa 2 2
acl 2 2
auth 0 0
authpriv 3 3
bootvar 5 5
callhome 2 2
capability 2 2
cdp 2 2
cert_enroll 2 2
cfs 3 3
confcheck 2 2
cron 3 3
daemon 3 3
device-alias 3 3
dstats 2 2
ethport 5 5
fc-redirect 5 5
fc-tunnel 5 5
fc2d 2 2
fcc 2 2
fcdomain 3 3
fcns 2 2
fcs 2 2
fdmi 2 2
feature-mgr 2 2
flogi 2 2
fspf 3 3
ftp 3 3
ipacl 2 2
ipconf 5 5
ipfc 2 2
kern 6 6
licmgr 6 6
local0 3 3
local1 3 3
local2 3 3
local3 3 3
local4 3 3
local5 3 3
local6 3 3
local7 3 3
lpr 3 3
mail 3 3
mcast 2 2
module 5 5
news 3 3
ntp 2 2
pfma 5 5
platform 5 5
port 5 5
port-resources 5 5
port_channel 5 5
prefpath 2 2
qos 3 3
radius 2 2
rdl 2 2
rib 2 2
rlir 2 2
rscn 2 2
scheduler 5 5
scsi-target 2 2
securityd 2 2
span 5 5
syslog 3 3
sysmgr 3 3
System Health LC 4 4
SystemHealth 4 4
tlport 4 4
user 3 3
uucp 3 3
vni 2 2
vrrp_cfg 5 5
vrrp_eng 5 5
vsan 2 2
vshd 5 5
wwn 3 3
xbar 5 5
zone 2 2
0(emergencies) 1(alerts) 2(critical)
3(errors) 4(warnings) 5(notifications)
6(information) 7(debugging) -
Sp43882 error message after upgrade to windows 7
hello,
i've just upgraded to windows 7 32 bit and installed the update sp43882 on my pavilion dv4 1409tu.
the problem now lies during the installation of the update,this error message appear
'' error 1904.module c:\program files\digitalpersona\bin\DPGPOUpdate.dll failed to register. HRESULT=2147024891. Contact your support personnel"
what should i do?
should i abort,retry or ignore the message?Hi Spikey I dont know if that driver is compatible with 7 and they dont seem to have released one yet here is the link for windows 7 drivers for your computer
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?lc=en&dlc=en&cc=nz&lang=en&product=3994757& -
Automatic refresh failed error message after upgrading to Server 2012R2
Configuration refresh message: The system cannot access one or more event logs because if insufficient access rights, file corruption, or other reasons. The message suggests I look in the ServerManager-ManagementProvider event log which I did. I find a number
event id 85 messages that state "Failed to query the results of bpa xpath: then there are a number of different entries with different location and the end of every message states "the system cannot find the file specified. The system cannot
find the path specified.
The computer is a stand alone root certificate server that was running 2008R2. I have not had this issue with any other upgraded server though this is the first standalone server I have upgraded.
There are also some Event ID 63 WMI errors in the application log indicating that the account being used to register providers is the LocalSystem account which is a security concern.
I searched the forums but no hits.
Thanks in advanced
[email protected]Hi,
WMI logs a warning event log message when a WMI provider running in the LocalSystem security hosting context is loaded. This is done to inform system administrators about the risk of elevation of privilege attacks. Such attacks are
possible if the provider code is not properly implemented.
https://technet.microsoft.com/en-us/library/dd315566%28v=ws.10%29.aspx?f=255&MSPPError=-2147217396
And for the error Failed to query the results of bpa xpath...
Can you run the BPA scan for the machine? BPA scan can be run using Server Manager console itself.
For this, go to "All Servers" canvas. Scroll below on this canvas to Best Practices Analyzer (BPA) tile. Click on "Tasks --> Start BPA Scan". Select the machine in opened window and complete the scan.
Regards.
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected] -
Error message when upgrading to 7.3.2.6
I just (attempted to) upgrade to 7.3.2.6 (and after the install, it all seems OK for now) - but during the install, I got a "files in use" error message window, mentioning that Windows Explorer was running (Process Id: 432), giving me the option to Retry, Ignore or Exit.
I tried all options - I even Exited and rebooted - and re-upgraded after that, but keep getting the same error... So far iTunes seems to have upgraded and appears to be working - but could the install have missed some components now - and therefore should I expect trouble ahead?Yes, i had the same error message after upgrading to 7.3.
I am using windows XP - i went to the Control Panel -> Add/Remove Programs -> Scrolled to iTunes & clicked on Change (not Remove), then clicked Repair. It all works fine after that.
Search this forum - i hope you find a solution. -
I have never been able to upgrade my phone I always get an error message after it goes 2 hours on the computer someone told me I could do it wifi but I don't know where to go to start the download
Make sure you have the right system requirements before you start to update the iOS, you will need:
Apple ID (required for some features)
Internet access
Syncing with iTunes on a Mac or PC requires:
Mac: OS X v10.5.8 or later
PC: Windows 7; Windows Vista; or Windows XP Home or Professional with Service Pack 3 or later
iTunes 10.5 or later (free download from www.itunes.com/download) -
Trying to update frpm itunes 10 to itunes11, but get error message after installation
I am trying to update my itunes to be compatible with my replaced iphone 4s (apllecare replacement) that is not compatible with my current iTunes 10.6. I have tried several times to upload th enew version of iTunes to no avial getting an error message after a "successful installation" and the itunes reverts to 10.6. Since my imac was an older unit I had to update to OSX 10.6.8 (sucessfully) and increase my RAM. I am 120bucks in the hole plus the 49 dolar surcharge for the iphone replacement and i am still no closer to restoring my phone. Help please
First backup your music and content.
Then delete iTunes 10.6 Drag the application from Finder > Applications to Trash. Empty Trash
Try and install 10.7 first iPhone 4s will work with this. You can find the download here
http://support.apple.com/kb/DL1576
Install it. Does itunes 10.7 now appear? Is your content all there? Connect up your iPhone and start syncing.
From there if you want to you can upgrade to iTunes 11 but it is only necassary if you have an iPhone 5 -
Error message after suspend to RAM on ThinkPad X230i
Hi,
I noticed there's alway an 'Unable to dock' error message after suspend
to RAM:
Arch kernel: ACPI: Low-level resume complete
Arch kernel: PM: Restoring platform NVS memory
Arch kernel: Enabling non-boot CPUs ...
Arch kernel: smpboot: Booting Node 0 Processor 1 APIC 0x1
CPU1 is up
smpboot: Booting Node 0 Processor 2 APIC 0x2
CPU2 is up
smpboot: Booting Node 0 Processor 3 APIC 0x3
CPU3 is up
ACPI: Waking up from system sleep state S3
ACPI: \_SB_.PCI0.LPC_.EC__.BAT1: docking
ACPI: \_SB_.PCI0.LPC_.EC__.BAT1: Unable to dock!
System info:
ThinkPad X230i, Linux 3.9.9-1-ARCH, systemd 204-3,
I have tried to set Handle{SuspendKey,HibernateKey,LidSwitch} all to
ignore, but I still get the same error message. Any other solution to
make that message disappear?
Regards.
Last edited by mert (2013-07-17 09:02:10)See http://forums.lenovo.com/t5/Linux-Discussion/T410-Ubuntu-Lucid-Two-Weeks-of-Use-the-Good-the-Bad-the... (the bit about USB after resume)
-
I have no trouble viewing apps in the iTunes Store on my iPad. However, every time I try to install a new app, I get an error message after a while - cannot connect to iTunes Store. This issues cropped up two days ago on my new iPad. Please help...
JUst experienced the exact same problem after changing password.Getting same message. Hope someone has an answer for this.
Maybe you are looking for
-
I had my ipod synced to an old computer that I no longer have how can i get all my stuff on the new itunes without erasing it
-
How to print report from JSP Page
Hi Everybody, I am developing a simple project in JSP with MS Access. I hav some tables and reports for them. I hav a JSP page which gets inputs from user and save it in the table. Its working fine. But my problems are, 1) I hav a button called "SAVE
-
Frequently I create a pdf and then I want to send it. After clicking send and the email pops up I compose the message. However, as I compose it, I have a question requiring me to look at the pdf. However, I can't page through the document because
-
Web Dynpro: How to set the header of Tabs in a Tabstrip?
Hi all, I created a tabstrip with 3 tabs. Now I am trying to give proper heading to each of the Tabs but unable to do so because I do not find any property to the Tab(s) for which, I can assign the heading. Only the following 4 Properties are availab
-
Special Character XML Web Service call from Flex
Hi, Let me first give a little background. I have to query and return data in XML format. To do so, I have created a custom DSC component. In cases where XML has special characters, LC throws error saying that XML is not properly formed. To over come