Ethernet controller driver not installing after Windows Server 2008 installation on Cisco UCS blade

I am using MDT 2010 to deploy Windows Server 2008 to a Cisco UCS B200 blade. The OS and hotfixes install with no problem. The system reboots and attempts to connect to the deployment share to continue with the task sequence and I receive an error stating
"A connection to the deployment share could not be made. The following networking device did not have a driver installed. PCI\VEN_1137&DEV_0043&SUBSYS_00481137&REV_A2"
The driver in question is the driver for the Ethernet controller for the UCS blade. More specifically, it is the network driver for the Palo card in the UCS Chassis. When I Ignore or Abort the install, I am able to manually install the driver and restart the
task sequence. The build then completes successfully with no further issue. I just cannot seem to automate the driver install. Has anyone dealt with this type of issue?

Vik and stealthfield - thank you for your responses.
I was preparing a script to manually move the driver into the c:\windows\inf location when I had to stop to create a new task sequence for a different build. It was while building this task sequence that I found the soulution to the problem.
In the Post Install -> Inject Drivers step of the Task Sequence, I noticed that it was executing a command of type "Inject Drivers" with a selection profile of "All Drivers" and "Install only matching drivers
from the selection profile" selected.
I changed this to run a command of type "Run Command Line" and specified that it execute "%Scriptroot%\ZTIdrivers.wsf". I noticed that this was selected in one of my other builds that was working properly, so I thought I'd
give it a try. - IT WORKED.
So to sum up, the solution was to change the type of command being executed in the "Post Install -> Inject Drivers" step of the task sequence. After this change, the machine came up and continued the task sequence with no further issues.
Thanks again for the responses - They were helpful and I do appreciate it.

Similar Messages

Hard drive not recognized during windows server 2008 setup

hard drive not recognized during windows server 2008 setup

Hi,
Whether the hard disk is recognized in BIOS?
Connect it to another computer to see if it could be recognzied incase the cause is the disk itself. Also please check if it is really a RAID instead of a single hard disk - a single disk should be recognized directly while RAID cannot be recognized until
a suitable driver is installed.
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Hp deskjet 2545 printer driver not supporting on windows server 2008 r2

I have purchased a 3 in 1 hp deskjet 2545 printer. I am trying to configure in on my home laptop (HCL) operating system: windows server 2008 R2, but unable to configure it. customer support executive told me hp deskjet 2545 printer driver is not compatible on windows server 2008 R2. but I have checked in my office and it is working fine on my office 2008 server. Please help.

Hello Arvindk,
Welcome to the HP Support Forums! I understand you are trying to use your HP Deskjet 2545 with your Windows Server 2008 R2. Because you are using a server your question will be best answered on the Commercial Forums: http://h30499.www3.hp.com/hpeb/
I was able to find this document for Installing the Printer Software on Windows Server 2003 or 2008, which may be helpful for you.
Thanks,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

USB Controller Driver (3.0) for Windows Server 2008 Standard Edition 32-bit

Hi,
I have recently built a HP DL320e Gen8 v2 server with Windows Server 2008 Standard Edition 32-bit & it's missing the USB Controller Driver which HP don't have. I have searched endlessly online without success. HP suggest I try Windows but I couldn't
find it in the Download Center either.
Can somebody please provide me with the USB Controller Driver for Windows Server 2008 Standard Edition 32-bit?
Regards
Naz

Hi,
Thanks for your posting.
For this issue, i think you need to search in the HP official website or contact the HP support.
Regards.
Vivian Wang

Ethernet Controller - Driver not installed - Compaq Presario

Hello, I am new here so be gentle
I have just bought second hand a Compaq Presario 6240EA, motherboard is a Compaq 07D0h.
In the hardware - device manager, it shows 'Other devices' - Ethernet Controller, with a large yellow question mark and exclamation mark.
Details in properties show the following: drivers for this device are not installed (Code 28)
PCI\VEN_10DE&DEV_01C3&SUBSYS_00A80E11&REV_C2\3&13C0B0C5&0&20
I have search the HP and Compaq websites for driver downloads and have downloaded all the nVidia drivers available on the Compaq site, none of which improve the situation.
Would there be somewhere else to look, I am at my wits end with this, any help would be much appreciated.
Thank you in anticipation.
This question was solved.
View Solution.

Please start your own thread rather than opening old ones back up. Also provide your full model number particularly when asking about hardware function which may involve drivers. We have to know precisely what hardware we are dealing with. Like the posts above, you may want to include the hardware id of the affected device.

Whether SAP Netweaver 7.02 could be installed on Windows Server 2008?

Hi ,
    I want to know Whether SAP Netweaver 7.02 not SP6 could be installed on Windows Server 2008? The help install document only mentioned Windows XP and Windows Server 2003, not mentioned Windows Server 2008, but I want to install it to Windows Server 2008 w64, I don't know whether could be installed successfully.
    Thanks for help!

Hi Munish,
    But I don't know where to download SAP JVM 4.
    My SAP NetWeaver 7.02 is only a trail version, so I couldn't download SAP JVM 4 from SAP Market, could you give me one?
   My G-mail is: [email protected]
   Thanks!
   If there is no SAP JVM 4, I only could install SAP NetWeaver 7.02 with j2sdk-1_4_2_19-windows-i586-p or j2re-1_4_2_19-windows-i586-p or j2sdk-1_4_2_09_windows_i586 and j2eesdk-1_4_02_2005Q1, I don't know which version I should choose to install.

VC Redist 2013 cannot be installed on Windows Server 2008 Core

Both vcredist_x86.exe and vcredist_x64.exe have this problem. And it can be reproduced 100%.
But all of them can be installed on Windows Server 2008 R2 Core, Windows Server 2012 Core, and Windows Server 2012 R2 Core.
From the log, it seems the installer depends some UI DLLs that are not included in this OS.
[060C:0618][2015-04-15T02:18:41]e000: Error 0x8007000e: Failed to load theme controls.
[060C:0618][2015-04-15T02:18:41]e000: Error 0x80004005: Failed to create main window.
Is it a bug or by design?
The following is the failed log:
[060C:0608][2015-04-15T02:18:41]i001: Burn v3.7.2829.0, Windows v6.0 (Build 6002: Service Pack 2), path: c:\vcredist_x86.exe, cmdline: '-burn.unelevated BurnPipe.{51C9AFD1-AA72-4BA2-8B12-E93691AFD7E3} {1B953492-AB47-43FA-A2BF-E1505C76194D} 3908'
[060C:0608][2015-04-15T02:18:41]i000: Setting string variable 'WixBundleLog' to value 'C:\Users\ADMINI~1\AppData\Local\Temp\dd_vcredist_x86_20150415021841.log'
[060C:0608][2015-04-15T02:18:41]i000: Setting string variable 'WixBundleOriginalSource' to value 'c:\vcredist_x86.exe'
[060C:0608][2015-04-15T02:18:41]i000: Setting string variable 'WixBundleName' to value 'Microsoft Visual C++ 2013 Redistributable (x86) - 12.0.30501'
[060C:0618][2015-04-15T02:18:41]e000: Error 0x8007000e: Failed to load theme controls.
[060C:0618][2015-04-15T02:18:41]e000: Error 0x80004005: Failed to create main window.
[060C:0608][2015-04-15T02:18:41]i500: Shutting down, exit code: 0x4005
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleAction = 5
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleElevated = 1
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleInstalled = 0
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleLog = C:\Users\ADMINI~1\AppData\Local\Temp\dd_vcredist_x86_20150415021841.log
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleManufacturer = Microsoft Corporation
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleName = Microsoft Visual C++ 2013 Redistributable (x86) - 12.0.30501
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleOriginalSource = c:\vcredist_x86.exe
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleProviderKey = {f65db027-aff3-4070-886a-0d87064aabb1}
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleTag =
[060C:0608][2015-04-15T02:18:41]i410: Variable: WixBundleVersion = 12.0.30501.0
[060C:0608][2015-04-15T02:18:41]i007: Exit code: 0x4005, restarting: No
Xiaojin

Hi Xiaojin,
Thanks for posting in MSDN.
I don't think this is a bug. From your description, you want to install VC redist on some servers core for Windows Server 2008, 2012. Based on my knowledge, server core has no graphical user interface (GUI), there is no desktop. Only code written using Windows
application programming interfaces (APIs) can run on Server Core.
More information about server core please refer to here:
What Is Server Core?
Best regards,
Shu Hu
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Web Service Client(Console App) not working on Windows Server 2008 R2 Standard Edition

I am trying to consume an ASMX Web Service in a console app, its working fine in Windows 7,Windows Server 2012 Standard,Windows Server 2008 R2 DataCenter,Windows Server 2008 R2 Enterprise, But its not working in Windows Server 2008 R2 Standard Edition which
is the deployment server.
I tried consuming the ASMX web service using Web Reference and Service Reference as well but its not helping. Its throwing up the following error,
Message:There is an error in XML document (1, 331491).
Inner Exception : System.Xml.XmlException: '.', hexadecimal value 0x00, is an invalid character. Line 1, position 331491.
The scenario is that i call the web service and it returns me an XML i am not able to receive the XML on Windows Server 2008 R2 Standard Edition.
Please provide suggestions on this I need to resolve this ASAP.

Hi,
This question is better asked here:
http://social.msdn.microsoft.com/Forums/en-US/home?forum=asmxandxml
Experts here are more familiar about it and they can give you more efficient suggestion.
Thank you.

Please help me with the step by step instructions on how to install a Windows server 2008 on a computer that has Windows 8 installed on it

Please help me with the step by step instructions on how to install a Windows server 2008 on a computer that has Windows 8 installed on it without formatting windows 8.Please email the steps , Thanks

Please help me with the step by step instructions on how to install a Windows server 2008 on a computer that has Windows 8 installed on it without formatting windows 8.Please email the steps , Thanks
Assuming your rig can support virtual machines, you can use Hyper-V and run another OS there.
Better practice however is to use a dedicated machine and use remote desktop to the server.
Corsair Carbide 300R with window
Corsair TX850V2 70A@12V
Asus M5A99FX PRO R2.0 CFX/SLI
AMD Phenom II 965 C3 Black Edition @ 4.0 GHz
G.SKILL RipjawsX DDR3-2133 8 GB
EVGA GTX 6600 Ti FTW Signature 2(Gk104 Kepler)
Asus PA238QR IPS LED HDMI DP 1080p
ST2000DM001 & Windows 8.1 Enterprise x64
Microsoft Wireless Desktop 2000
Wacom Bamboo CHT470M
Place your rig specifics into your signature like I have, makes it 100x easier to understand!
Hardcore Games Legendary is the Only Way to Play!

Addon not working on Windows Server 2008 OS

Dear Friends,
I have developed an addon in XP and its working fine with XP operating system but it is not working on Windows Server 2008 Standard. Error is "An Attempt was made to load a program with an incorrect format.(Exception from HRESULT: 0x8007000B)".
Regards,
Mahesh.
Edited by: mahesh A on Sep 19, 2009 9:26 AM

Hi,
Since only Windows 2008 SBS is supported with SAP Business One and that Server is available for 64bit Hardware as defined by Microsoft, I guess you should look into that direction.
Regards
Mario

Group Chat feature in Office Communications Server 2007 R2 does not work in Windows Server 2008 R2 domains

   Hello to all, there are two confliting articles about this topic:
   1-
http://technet.microsoft.com/en-us/library/upgrade-domain-controllers-to-windows-server-2008-r2(v=ws.10).aspx#BKMK_Whatsnew : this one says that it does not work "The Group Chat feature in Office Communications Server 2007 R2 does not work in Windows
Server 2008 R2 domains". This article was updated in 2013.
   2-
http://technet.microsoft.com/en-us/library/ee692314(office.13).aspx: this other article says that it will function "Office Communications Server 2007 R2 Group Chat will function in a Windows Server 2008 R2 forest". This article was updated in
2010 and was refered by the first one.
   What is the correct support position for Group Chat feature in Office Communications Server 2007 R2 and Windows Server 2008 R2 domains?
   Regards, EEOC.

Hi,
I notice the following sentence in the link below “Office Communications Server 2007 R2, Group Chat will not function in a Windows Server 2008 R2 forest or when Group Chat member servers are joined to a Windows Server 2008 R2 domain.
We know of an issue with changes in Windows 2008 R2 that requires a Group Chat Client and Group Chat Admin Tools hotfix. The Group Chat Client and Group Chat Admin Tools hotfixes are currently scheduled for mid-April 2010.”
http://blogs.technet.com/b/nexthop/archive/2010/11/06/supportability-for-office-communications-server-2007-r2-and-windows-server-2008-r2.aspx
So in my opinion, if you update to the latest version of Windows Server 2008 R2, OCS Server 2007 R2 and Group Chat Client, Group Chat Admin Tools to the latest version, it should work.
However, the best method for you is make a lab to test the problem firstly.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

TCP / IP Protocol Driver - not installed (using Windows 7 Home Premium (64 bit) Service Pack 1

I am using a ThinkPad T520 laptop. Lenovo Solutions Center keeps referring me (with a yellow exclamation mark) to the Device Manager and alerting me to a "non-critical" error. The message is "TCP / IP Protocol Driver - not installed".
I have found numerous pieces of advice for Windows XP and Vista - but very little for Windows 7. I have however tried the Microsoft "Fix it" solution and it had no effect.
I am still able to connect to the internet via Ethernet cable and wifi. It is however worrying that the warning keeps being raised.
Does anyone know how I can fix it?

Hi Tripplec.
Thanks for the reply. I am away from home at present without my ThinkPad, so will try it at the weekend. I am an experienced computer user but this is a brand new machine and I have never had a laptop that produced error messages without providing any suggested fixes. It seems that Lenovo is not suitable for ordinary home users, but only for computer engineers. Sadly that is not me... so before I plunge in, can I just check some details?
1. You suggest removing the offending network adapters in device manager. Which are the offending adapters that cause a TCP/IP protocol driver error? I am nervous of removing the wrong things and making it worse!
2. You also suggest that I go to Network Connections via Control panel, properties of adapter, Install and select the desired Protocol(s) and install them. Is that an alternative fix to 1 above - or an essential follow-on after removing the offending adapters? (Last week I searched the machine and the Lenovo support page of drivers - and never found a TCP/IP protocol driver. If you know where one can be found, I would prefer to instal a new driver, rather than delete other devices and hope that the machine reinstalls them later!).
Much obliged for your assistance.
Fillet

IE is not showing on windows server 2008 after updates

Hi,
I have installed Window server 2008 R2.
After installing i found IE 8 on the server, but after 1day it automatically updated some softwares and now IE is not showing on my system.
i.e IE uninstalled after the updates to the windows server.
Please can some one help me to get the IE. I tried installing IE8, IE9 after downloading but it is showing "Internet Explorer 8 is not supported on this operating system"
Regards
Krishna

Hi,
Internet Explorer 8 runs on any of the following operating systems:
Windows Vista, 32-bit versions
Windows Vista, 64-bit versions
Windows Vista with Service Pack 1 (SP 1) or a later version
Windows XP, 32-bit versions with Service Pack 2 (SP2) or a later version
Windows XP Professional, 64-bit Edition
Windows Server 2003, 32-bit versions with Service Pack 2 (SP2) or a later version
Windows Server 2003, 64-bit versions with Service Pack 2 (SP2) or a later version
Windows Server 2008, 32-bit, or a later version
Windows Server 2008, 64-bit, or a later version
Please expand the below path to check whether IE is there:
C:\Program Files\Internet Explorer
Regards,
Yan Li
Regards, Yan Li

Portege M750 - PCI controller software not installed on Windows 7 64bit

Hi, had an upgraded SSD for my machine so decided to do a fresh install of Windows 7 64bit and now I have and error saying PCI controller software is not installed, tried windows update no luck - any ideas please?
Thanks, Peter

OK cool advice - thanks it is from Intel and is
0x2A44 Chip Number: Mobile 4 Series Chipset
Chip Description: Intel Management Engine Interface
Notes: ftp://ftp.vaio-link.com/PUB/VAIO/ORIGINAL/ME DRIVER INTEL 4.0A _ 4.0.0.1105.ZIP
Downloaded, installed and working - thanks for the quick advice!
Peter

2007A SP01 PL10 not installing on Windows Server 2003 ?

Hi all:
Yesterday 2007A SP01 PL10 was released. Trying to keep our customer's installations current, I proceeded to try and install the patch on different systems. So far I was lucky with Windows XP and Windows Server 2008 trial installations. However, on all the Windows Server 2003 installations I have tried (OS patched completely), the COMMON database upgrade either closes without error message, or opens up a debug message with no error number or description after clicking the very first "Next" button in the installation program.
Has anybody seen the same effect anywhere? Has anybody been able to successfully install PL10 on a Windows Server 2003? Are there any known issues?
Thanks,
Joerg.

Hi,
I got the same answer to my support call for my error messages. We are loading that patch and will attempt again. Ironically, I had looked at the same note, and even bookmarked it becuase of the slow 8.8 client upgrade thread, but I didn't think the two were related.
The note indicates only that SAP Business One does not start after patch file application.
"You might encounter one of the following situations after having applied a new SAP Business One patch file:
Your SAP Business One system fails to start after you have applied a new SAP Business One patch file that you downloaded from SAP Service Marketplace.
If you want to find out whether you are affected by this problem, refer to section "Detecting whether SAP will not start up due to missing MS patch" in the attached PDF document.
Your SAP Business One system runs fine but you did not apply the Microsoft security fix mentioned above. However, future downloads of SAP binaries from SAP Service Marketplace might not work (depending on release, etc.)."
If it is also affecting the installation of patches (i.e SAP runs fine, but you can't run a patch installer) the message should also indicate that so that people will know to use this fix in the future.
Hopefully I too will have a resolved issue. I'll post the results.
Daryl

Ethernet controller driver not installing after Windows Server 2008 installation on Cisco UCS blade

Similar Messages

Maybe you are looking for