Ethernet Port not working 50% of the time?

On my new GD55 P67 50% of the time I start my computer the Ethernet port does not work. I know the cable is good because I have tried several cables. It seems to have problems right after I installed SP1 for windows 7. Is their a known problem with the Ethernet port on this motherboard?

By "start my computer" do you mean start from a complete shutdown, start from S1/S3 sleep or start from hibernation?
The next time you start the computer and your Ethernet port doesn't work, open up a Command Prompt window and type "ipconfig /all" (without the quotes).  Copy and paste the results displayed for the Ethernet port you are having a problem with (or just copy it all if you are not sure which section belongs to the port in question).
- D

Similar Messages

  • Downloaded ios7 to my iphone4s and now my volume control does not work 99 % of the time. what can i do to solve the problem

    I downloaded ios7 to my iphone and now my volume control does not work 99% of the time. Is there something I need to do to correct this?

    Adjust the Volume Control in Control Center, or try a RESET.............

  • Microfone and speaker is not working most of the times

    Microfone and speaker is not working most of the times. But after restarting it sometimes it works and again everything gets mute

    Hello there, Paras1111.
    The following Knowledge Base article offers up some great information for troubleshooting issues with microphone and speaker. Feel free to review the links under "Acoustic-speaker/microphone/receiver:"
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • Mountain Lion Mac Mini Server Ethernet Port Not Working

    I have a Mac Mini Server and once I upgraded to Mountain Lion Server the Ethernet port is unresponsive. It worked before upgrading. Is there something with Mountain Lion Server that is causing the Ethernet port not to work properly?

    Make a "Genius" appointment at an Apple Store.
    Back up all data on the internal drive(s) before you hand over your computer to anyone. If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
    Keeping your confidential data secure during hardware repair
    *An SSD doesn't need to be zeroed.

  • Spotlight search (search iphone) does note work half of the time.

    When searching my iphone4s nothing show up half the time. (spotlight search)  Sometimes it works fine and other times I type and it does not search or show anything. Powering down the phone did not fix.  Just odd it works for a minute then seems to stop completly.  No other problems besides this one.

    OK, well at least it works 50% of the time.

  • USB Ethernet port not working after ML install

    After installing ML I cannot get the USB Ethernet port to work. Have searched for andriod file transfer agent but cannot locate it as previously mentioned.

    Same Problem over here. Has anyone a good idea how to fix this problem?
    After installing ML i cannot get my original Apple USB Ethernet port to work (Macbook Air 2011).

  • HT201401 My iphone 5 volumn down button does not work most of the time. it feels fine.  in an otterbox defender. this is my second iphone that it is doing the same thing.

    i have a iphone 5. the volume button going down only does not work.  this is my second phone with the same problem.  i have had otterboxes for both phones.

    Does not work even with the case off. I formatted and rebooted, reset, called apple and sent the last one back. It was free but this is getting old. I have had all iPhones and this is the only one I have had issues.

  • Built-in ethernet port not working in unibody Mac Mini

    Hi,
    So ever since I acquired this new mac mini I haven't been able to get it to recognize any devices connected via ethernet. I obviously checked the cables and all is good there. I tried connecting it to another mac, and while the other machine was detecting a device (the mac mini) at the other end of the cable, the mac mini kept saying that the cable is unplugged or the device off.
    After several days of having the issue I decided to remove the ethernet service from the network preference pane to set it up again but to my surprise, the built-in ethernet option was not available (I only got airport, firewire, bluetooth DUN, VPN, PPPoE and 6 to 4). At this point I tried removing the networkinterfaces.plist file form the system configuration folder in the system preferences folder to no avail. I then tried to zap the PRAM, NVRAM, reset the SMU, SMC and all that kind of things to get the port recognized by the system but no luck.
    When I look at the system profile I get these weird results in Ethernet Cards:
    pci14e4,4353:
    Type: Other Network Controller
    Bus: PCI
    Vendor ID: 0x14e4
    Device ID: 0x4353
    Subsystem Vendor ID: 0x106b
    Subsystem ID: 0x0093
    Revision ID: 0x0001
    Link Width: x1
    BSD name: en0
    Kext name: AppleAirPortBrcm43224.kext
    Location: /System/Library/Extensions/IO80211Family.kext/Contents/PlugIns/AppleAirPortBrcm 43224.kext
    Version: 425.16.2
    Comparing it to other macs I have It should read "ethernet" rather than that strange pci name on top and the kext name shouldn't read airport but something like AppleIntel and in location it shouldn't direct to the IO80211Family.kext package but rather to the IONetworkingFamily.kext.
    So I popped in the system install DVD and fired up System profiler and at that point I didn't even get an "ethernet cards" option in the left side pane. So this is leading me to believe that the hardware is not being recognized at all, so maybe it's damaged. I did replace the HDD with a bigger one and change the RAM modules to bigger ones but I don't think I could have damaged the hardware in these processes, also I don't see how this would affect the ethernet port as it's integrated to Motherboard and didn't messed with it at all (I was very careful, to say the least!).
    The last thing to do is reinstalling the system but I don't think it'll help (after seeing that the ethernet port is not even being detected by the install OS) but I need to offload all the data from my internal disk and at the moment I don't have an spare drive to do it.
    So, what's the recommendation? A field trip to an Apple Store? Closest one is like 3,000 km from where I am right now, so...
    Well, thanks for any pointers, suggestions and help in general.

    I do not have any answers for you. Yes it appears to be reading what should be an ethernet card as an AirPort card. Have you played around with trying to install another version of Mac OS X other than the version that shipped with the Mac mini? Apple has long told us that we should not install a version of Mac OS X that was older than the shipping version. With the Mid 2010 Mac mini, the Restore DVD has the only version of Snow Leopard that will work with this Mac mini's specific hardware. At least until Apple releases 10.6.5. If you have installed other versions of Mac OS X, then erasing the HDD and installing the OS from the Restore DVD(s) that shipped with the mini may get you back to the point you need to be.
    Unfortunately I think that you voided your Apple Warranty when you installed the different HDD. That was always a question in the past when folks wanted to open the former version of Mac minis and upgrade the RAM. But with the 2009 models folks started reporting here in the Apple Discussions that Apple was informing them that they had voided their warranty by opening their Mac mini. This new model made the RAM user upgradable, but the User Manual specifically states on page 43, 54 and 61 that there are no user serviceable parts in the Mid 2010 Mac mini except the memory.
    Dah•veed

  • HP 7210 All-In-One Ethernet Port not working

    The green Ethernet port light is not lighting and the computer can no longer find the printer.  I believe it may have been damaged by a power surge during a lightning storm.  I have checked the Ethernet cable that connects it and it is working fine with my laptop so it is not the cable coming into the printer.  The printer works fine with the USB cable and all other printing, faxing and copying functions are working fine.  Is it possible to repair or replace the Ethernet port?
    I have also tried setting the IP address back to default and manually setting the IP address.  The port is just not recognizing the cable.

    Jim B - First, thank you so much for helping me.
    I was able to get the green port light to light-up by performing the steps 1 - 5 you recommended.  Also the amber data light is on but not blinking.  In fact now they both stay lit even when the cable is removed.  When I use the same cable with my laptop the green light comes on and the amber light blinks.
    Unforntunately, the printer is still not finding the IP address.  I tried the function to "Restore the Network Defaults" and I also tried to manually set the IP Address.  When I print the network settings it indicates the status is "Offline" and I have the following changes:
                                                                    Was                                                  ​                     ISActive Connection Type:               Wired                                                  ​                  None
    ULR:  http://                                    192.168.1.102                                                  ​   0.0.0.0
    Hostname:                                       HP1B376F                                                  ​         HP1B376F
    IP Address:                                       92.168.1.102                                                  ​    0.0.0.0
    Subnet Mask:                                   255.255.255.0                                                  ​  0.0.0.0
    Default Gateway:                            192.168.1.1                                                  ​       0.0.0.0
    Configuration Source:                      DHCP                                                  ​                Not Specified
    DNS Server:                                      68.230.242.25                                                  ​   0.0.0.0
    Link Configuration:                          100TX – Full                                                  ​      None
    mDNS:                                              Officejet 7200 series (47E2A6)                          Not Specified
    Any ideas what I should try next?
    Thanks
    Connie

  • Ethernet Port not working

    I had bought a new HP ENVY 15-AE009TX just a week back and now suddenly my ethernet connection is not working. It seems the problem is with the port because the 2 lights keep disappearing and start after a few seconds i thought they were supposed to be on constantly one white light and another blinking. I dunnow what else could be the problem the drivers seem to be fine. The troubleshooter in windows says to attach the ethernet cable when i already have it inserted. Any help is appreciated.

    Which port are you using?
    The second (upper) NIC is only activated once the first (lower) NIC is.
    If you're trying to use the upper NIC without first using the lower NIC, that could be your problem.
    Once you've verified that, check the switch settings and make sure the port is configured for auto-negotiation. By default the Mac will use auto-negotiation and it's possible that you won't get a link if the switch on the other end is not set the same (e.g. it's set for 100-full).
    Of course, if you've changed the Mac's settings (in Network preferences -> Ethernet) to something other than 'Auto', then you should make sure the switch is set the same.

  • OSX 10.9 & ethernet port not working

    Before I upgraded to OSX Mav 10.9 on my MBP 13" mid-2010, my ethernet port worked fine. Yesterday I plugged in using the ethernet for the first time since the upgrade and it doesn't work.  The Network app says "unplugged" even though it clearly is. The router doesn't show a green light either when connected to any port. I know the cable and router are fine (both checked using a PC). 
    Am I the only one or is this a more common issue?
    If so, is there a fix?

    let me reiterate. 27 ' iMac 3.06 GHz Intel Core 2 Duo just updated to 10.6.6 uses AirPort to access the internet. Set up to share it's internet connection via ethernet with PPC Dual 2.3 G5 running 10.5.8. Up until the 10.6.6 update things were fine. After updating the iMac's OS, the PPC lost it's internet connection. On the PPC's network System Prefs, the built in ethernet is connected and green. The iMac is in the finder under Shared. On the iMac, the PPC is in the finder under Shared and in Network settings the ethernet connection has a self-assigned IP with a yellow light. I have reset and rebooted all settings and devises on the network with no resolve.

  • IOS 7.1 Upgrade - home button double click not working most of the time

    Hi,
    Not sure, if anyone else had encountered this issue after upgrading to iOS7.1.
    I am using iPhone5S 32 GB and it was working fine with home button (double click, mostly used to see & close other applications running in background) till I upgraded to iOS7.1. After iOS7.1 upgrade, most of the time, I am unable to see running applications. After trying for 4-5 times, I managed to see running application
    Is there any fix or workaround for this issue?

    Settings > General > Accessibility > Home-Click Speed - Change from Default to Slow

  • Search feature not working most of the time

    My  search feature on my iPhone 4 rarely works anymore. After swiping screen from left to right or pressing HOME button nothing happens when I start typing. If I press the search button it will take a long time before responding.

    Sharing between Leopard and Snowleopard does not work reliably. For this reason, we do not recommend mixing Operating Systems.
    Hope this helps,
    Syd

  • Shared printer not working (most of the time)

    I have a Mac Pro running Snow Leopard using a shared Epson R380 printer connected to a G5 (running Leopard) . Most of the time it doesn't work, but occasionally it will. On the Mac Pro, the Epson monitor says "print job accepted" but doesn't change. On the G5, the Epson monitor shows the print job, but says "job stopped". When trying to resume the job, a warning box pops up on the G5 saying "Operation C0uld Not Be Completed - client-error-not-possible".
    The shared printer works fine (most of the time, too) with another networked Mac, a Mac mini G4 running Leopard.
    All OS's are the latest possible.

    Sharing between Leopard and Snowleopard does not work reliably. For this reason, we do not recommend mixing Operating Systems.
    Hope this helps,
    Syd

  • Ethernet Port Not Working After 10.6.6 Upgrade

    Hello! Since upgrading to 10.6.6, I have lost my Ethernet port connectivity. AirPort is working fine.
    I have done the following:
    -checked ethernet cable
    -used System Preferences/Network to check connection and try to create a new one
    -used Diagnostic button
    -zapped PRAM
    -reset SMC
    -repaired my disk permissions
    -installed the 10.6.6 combo update
    -booted in Safe Mode and then restarting
    Is anyone aware of an incompatibility with 10.6.6 and the Yukon adapter?
    Any suggestions greatly appreciated!
    Marvell Yukon Gigabit Adapter 88E8053 Singleport Copper SA:
    Name: ethernet
    Type: Ethernet Controller
    Bus: PCI
    Vendor ID: 0x11ab
    Device ID: 0x4362
    Subsystem Vendor ID: 0x11ab
    Subsystem ID: 0x5321
    Revision ID: 0x0022
    Link Width: x1
    BSD name: en0
    Kext name: AppleYukon2.kext
    Location: /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleYukon2 .kext
    Version: 3.2.1b1
    Hardware Overview:
    Model Name: MacBook
    Model Identifier: MacBook1,1
    Processor Name: Intel Core Duo
    Processor Speed: 2 GHz
    Number Of Processors: 1
    Total Number Of Cores: 2
    L2 Cache: 2 MB
    Memory: 1 GB
    Bus Speed: 667 MHz
    Boot ROM Version: MB11.0061.B03
    SMC Version (system): 1.4f12
    Message was edited by: bhughes2172

    let me reiterate. 27 ' iMac 3.06 GHz Intel Core 2 Duo just updated to 10.6.6 uses AirPort to access the internet. Set up to share it's internet connection via ethernet with PPC Dual 2.3 G5 running 10.5.8. Up until the 10.6.6 update things were fine. After updating the iMac's OS, the PPC lost it's internet connection. On the PPC's network System Prefs, the built in ethernet is connected and green. The iMac is in the finder under Shared. On the iMac, the PPC is in the finder under Shared and in Network settings the ethernet connection has a self-assigned IP with a yellow light. I have reset and rebooted all settings and devises on the network with no resolve.

Maybe you are looking for

  • What is the diffrence between BAPI and RFC and business object

    Hi Experts, Can anybody tel me what is the diffrence between RFC and BAPI , and also what is ther relation with business object? Thanx in advance. Nilesh Hiwale

  • Re-purchasing an app

    I have an app on the Store (Growl, FWIW) that won't let me update.  When I try, it refuses me with an error that says "To update this application, sign in to the account you used to purchase it." I've tried both of my apple IDs, and get the same mess

  • Form refresh in debug mode

    I am trying to debug an issue on why my labels are not changing color when I update the forecolor property.  When I run the code below in debug mode I do not see the label change color.  I know my real issue is more involved but if the form does not

  • Report - 2 rows for 1 record

    How do I modify a report so that each record is represented by 2 rows? For instance, see the following columns, where COMMENT would always be in a separate row below the other attributes.: (record 1) DATE, AUTHOR, SUBJECT COMMENT (record2) DATE, AUTH

  • Running out of numbers in NRIV RP_REMIT REM1

    Help guru's!!! We are unable to update 3rd party tables.  We are receiving the message from RPURMU00 (3rd party store): "Number xxxxx of number range RP_REMIT REM1 already used.  Please check number range.  No table update performed." Our range is 00