Exported mp3 file size is huge!

Does anyone know how to control the size of an exported song? For a 5 minute track I'm getting a 60Mb MP3!! I'm guessing this is done by setting the a different bit rate for the exported song but can't find any options in Garageband to do this.
With such huge file sizes it makes it difficult to share the song through my website.

No, you're not getting a 60 MB MP3, but a 60 MB AIFF file, and that's the regular size for uncompressed audio files. The bitrate in GB is fixed, and you wouldn't want to change it. Instead, convert the file into an MP3 or AAC in iTunes.
(Come back if you need help with doing that.)

Similar Messages

When I narrate my keynote presentation, why is the file size so huge?

When I narrate my keynote presentation, why is the file size so huge?

Here are the steps so you can see all the files that make up your Keynote…
Go to the Finder and find your Keynote file and make sure that it has the .key extension on it. If it doesn't, click it and command i to view info and uncheck the box that says Hide Extension.
Delete the .key and change to .zip and then click the use .zip in the dialog box that comes up
Double click the new .zip file and it will change it to a folder
Open the folder there are the files
Close the folder and add .key to the end of the name and click Add in the dialog box (this will change it back to a Keynote file)
You might be able to do this and convert the voice narration to a smaller format.

Aperture is exporting large file size e.g. original image is 18.2MB and the exported version (TFF 16 Bit) is 47.9MB, any ideas please

Aperture is exporting large file size e.g. original image is 18.2MB and the exported version (TFF 16 Bit) is 47.9MB, any ideas please

Raws, even if not compressed, Sould be smaller than a 24-bit Tiff, since they have only one bitplane. My T3i shoots 14 bit 18MP raws and has a raw file size of 24.5 MB*. An uncompressed Tiff should have a size of 18 MP x 3 bytes per pixel or 54 MB.
*There must be some lossless compression going on since 18 MP times 1.75 bytes per pixel is 31.5MB for uncompressed raw.

SSRS report Excel Export file size is huge

Hello everyone,
I am facing an issue with SSRS report exporting to Excel.
Issue : Exported file size is too big.
I have a matrix report ( parametrized report ) it fetches data from multiple table.
initially when
1) I select all parameters all values
2) load the report after that
3) exporting to excel
so exported file size was about 10 Mb to 12MB
Now, suddenly from this month exported file size is too big around 62 MB for same data,
I checked on different forums and tried the solutions but it didn't worked,
can anyone please suggest me on this.
My environment is
Visual studio (BIDS) 2008
SQL Server 2008 R2
Excel 2007
Thanks

Hi UdayKGR,
According to your description, when you export a report into an excel file, the exported file size is too huge. Now you want to reduce the file size. Right?
In this scenario, do you export the report into excel 2003 file? When reports are first exported and saved to Excel 2003, they do not benefit from the file optimization that Excel automatically applies to its *.xls workbook files. The larger file size can
cause problems for e-mail subscriptions and attachments. To reduce the size of the *.xls files for exported reports, open the *.xls files and then resave the workbooks. Resaving the workbooks typically reduces their file sizes by 40 to 50 percent. Also please
try to install the Reporting Services 2008 R2 Service Pack 2 and reduce the merged columns in exported excel file. For more information, please see the links below:
Exporting to Microsoft Excel (Report Builder and SSRS)
problem
regarding the size of exported report from reporting services to excel format
SSRS Export to Excel - Performance
If you have any question, please feel free to ask.
Best Regards,
Simon Hou

Export to Word file size is huge

Sometime after the end of March, the "Export to Word..." action in Pages has started producing very large file sizes. The Pages file itself will be 119KB, but after exporting to .doc, it will become 1.5MB. I have to export Pages files to Word all the time, to submit files to submission systems that have max file sizes, so I've been unable to upload my files, which is obviously a problem (and didn't used to be).
To fix this I have tried... restarting. I have deleted the Pages plists, restarted. I have tried exporting on a different computer with the newest version of Pages, which produced the same file size result. I have copy/pasted the text into a new file, tried again. Etc, etc. In the end, I had to borrow a friend's computer to pull the 1.5MB Word export into Microsoft Word itself and resave, to get the expected smaller file size of 47KB.
Please help. Or, if there is no solution, I'll report as bug to Apple Feedback. Thanks!

To my knowledge all Pages 5 Exports have been particularly bloated.
Since I have not considered Pages 5 worth using for serious work I can't compare between Pages 5.1 and Pages 5.2 as to whether the problem has actually got worse.
All I know is that Pages 5 files & Exports are massively bigger than Page '09 files & Exports.
Peter

Exported media file size issues Sometimes one size, Sometimes another without making any changes in FCPX?

Hi there
I'm having some strange issues with files sizes from
Share>Export Media
I'm not changing anything about the video (just moving an audio track forwards and backwards ever so slightly to try and get it to the correct timing), nor am I changing anything about the way I export the video.
I am always using the EXACT same settings
Sometimes finder states my video is 1.15GB, sometimes its states its 3.8GB
But then when I close Finder down and then go back into Finder again to find the file it states its gone from 1.15GB to 3.8GB
I'm not sure if this is a error with my system or Final Cut Pro X?
By the way I'm running 10.0.5
Thanks

Bob,
Well, the issue has gone to press and I have upgraded to Snow Leopard and CS5. Initial tests show that the problem still exists, and that it is related to the XML tags. The problem occurs both with legacy (CS4) documents and documents created from scratch in CS5. As I mentioned before, it only seems to happen when overrides are applied to paragraph styles.
Here is a sidebar as exported from InDesign. Overrides were applied to the two headlines to modify color, point size and baseline shift:
The file with XML tags, packaged and opened in InCopy CS5:
The same file with XML tags removed, packaged and opened in InCopy:
OK. Now is when things start to get really interesting.
I thought perhaps that exporting the InDesign file as an IDML document, then reopening it, might perhaps fix the problem. But, no. In fact, when I reopened the IDML file in InDesign, the font styles were broken in _exactly_ the same places as they were in InCopy. Apparently, whatever problem InCopy is having with the XML tags is being duplicated by the IDML export. (Do these processes share the same file format?)
For example, here is a title page from the magazine as a screen grab in InDesign. Overrides were applied to the top headline on a line-by-line basis:
The same file, exported as an IDML file and reopened in InDesign:
As with InCopy, when the XML tags are removed, the IDML file reopens in InDesign just fine. Unfortunately, removing the XML tags is not a option. We need them to repurpose the content after it goes to press.
This is a real bug, and for us it's a serious one. I'm surprised it hasn't come up before. Is there any way to draw this to Adobe's attention? I'd be more than happy to share any of these files if that would help.
Steve

Problem exporting '.txt' file size 23 KB and '.zip' file size 4 MB

I am using Apex 3.0 version screen to upload '.txt' file and '.zip' file containing images.
I can successfully export '.txt' file and '.zip' file containing images as long as '.txt' file size is < 23 KB and '.zip' file size < 4 MB from database table 'TBL_upload_file' to the OS directory on the server.
processing of Larger files (sizes 35 KB and 6 MB) produce following Error Message.
‘ORA-21560: argument 2 is null, invalid or out of range’ error.
Here is my code:
I am using following code to export Documents from database table 'TBL_upload_file' to the OS directory on the server.
create or replace procedure "PROC_LOAD_FILES_TO_FLDR_BYTES"
(pchr_text_file IN VARCHAR2,
pchr_zip_file IN VARCHAR2)
is
lzipfile varchar(100);
lzipname varchar(100);
sseq varchar(1000);
ldocname varchar(100);
lfile varchar(100);
-- loaddoc (p_file in number) as
l_file UTL_FILE.FILE_TYPE;
l_buffer RAW(32000);
l_amount NUMBER := 32000;
l_pos NUMBER := 1;
l_blob BLOB;
l_blob_len NUMBER;
l_file_name varchar(200);
l_doc_name varchar(200);
a_file_name varchar (200);
end_pos NUMBER;
begin
-- Get LOB locator
SELECT blob_content,doc_name
INTO l_blob,l_file_name
FROM tbl_upload_file
WHERE DOC_NAME = pchr_text_file;
--get length of blob
l_blob_len := DBMS_LOB.getlength(l_blob);
-- save blob length to determine end position
end_pos:= l_blob_len;
-- Open the destination file.
-- l_file := UTL_FILE.fopen('BLOBS','MyImage.gif','w', 32767);
l_file := UTL_FILE.fopen('BLOBS',l_file_name,'WB', 32760); --use write byte option supported in 10G
-- if small enough for a single write
IF l_blob_len < 32760 THEN
utl_file.put_raw(l_file,l_blob);
utl_file.fflush(l_file);
ELSE -- write in pieces
-- Read chunks of the BLOB and write them to the file
-- until complete.
WHILE l_pos < l_blob_len LOOP
DBMS_LOB.read(l_blob, l_amount, l_pos, l_buffer);
UTL_FILE.put_raw(l_file, l_buffer);
utl_file.fflush(l_file); --flush pending data and write to the file
-- set the start position for the next cut
l_pos := l_pos + l_amount;
-- set the end position if less than 32000 bytes, here end_pos captures length of the document
end_pos := end_pos - l_amount;
IF end_pos < 32000 THEN
l_amount := end_pos;
END IF;
END LOOP;
END IF;
--- zip file
-- Get LOB locator to locate zip file
SELECT blob_content,doc_name
INTO l_blob,l_doc_name
FROM tbl_upload_file
WHERE DOC_NAME = pchr_zip_file;
l_blob_len := DBMS_LOB.getlength(l_blob);
-- save blob length to determine end position
end_pos:= l_blob_len;
-- Open the destination file.
-- l_file := UTL_FILE.fopen('BLOBS','MyImage.gif','w', 32767);
l_file := UTL_FILE.fopen('BLOBS',l_doc_name,'WB', 32760); --use write byte option supported in 10G
-- if small enough for a single write
IF l_blob_len < 32760 THEN
utl_file.put_raw(l_file,l_blob);
utl_file.fflush(l_file); --flush out pending data to the file
ELSE -- write in pieces
-- Read chunks of the BLOB and write them to the file
-- until complete.
l_pos:=1;
WHILE l_pos < l_blob_len LOOP
DBMS_LOB.read(l_blob, l_amount, l_pos, l_buffer);
UTL_FILE.put_raw(l_file, l_buffer);
UTL_FILE.fflush(l_file); --flush pending data and write to the file
l_pos := l_pos + l_amount;
-- set the end position if less than 32000 bytes, here end_pos contains length of the document
end_pos := end_pos - l_amount;
IF end_pos < 32000 THEN
l_amount := end_pos;
END IF;
END LOOP;
END IF;
-- Close the file.
IF UTL_FILE.is_open(l_file) THEN
UTL_FILE.fclose(l_file);
END IF;
exception
WHEN NO_DATA_FOUND THEN
RAISE_APPLICATION_ERROR(-20214,'Screen fields cannot be blank, Proc_Load_Files_To_Fldr_BYTES.');
WHEN TOO_MANY_ROWS THEN
RAISE_APPLICATION_ERROR(-20215,'More than one record exist in the tbl_load_file table, Proc_Load_Files_To_Fldr_BYTES.');
WHEN OTHERS THEN
-- Close the file if something goes wrong.
IF UTL_FILE.is_open(l_file) THEN
UTL_FILE.fclose(l_file);
END IF;
RAISE_APPLICATION_ERROR(-20216,'Some other errors occurred, Proc_Load_Files_To_Fldr_BYTES.');
end;
I am new to the Oracle.
Any help to modify this scipt and resolve this problem will be greatly appreciated.
Thank you.

Ask this question in the Apex forums. See Oracle Application Express (APEX)
Regards Nigel

InDesign - Export PDF file size

Hey everyone. I use InDesign to create my resume for job apps and whatnot. I've found that many corporate sites only accept file sizes under a certain limit (usually 500kb or smaller). My resume is usually around 590-610kb. Is there any way that I can reduce the file size without losing significant quality, or even any?
Cheers.

rayzha wrote:
So I need to d/l adobe acrobat?
OK, so this sounds like you don't have a Creative Suite package, or perhaps you are using Creative Cloud and didn't install Acrobat Pro.
The free Adobe Reader will not help you to optimize a PDF, you need the full, paid, Acrobat application. Uwe's suggestion to distill might get you a smaller PDF, but again, without Acrobat you won't have Distiller. There are a few freeware Distiller clones that would probably work for plain text, but I doubt there's much that can be done to bring the size down on a file that has nothing but text in it without removing the non-graphic disposables like metadata, and the embedded page thumbnails, which requires the optimizer.
It occurs to me that one reason your exported PDF might be large is that ID always embeds fonts unless they are restricted. If you are using common system fonts that you know your viewer will have, you can distill PDF without embedding fonts and save a couple of bytes. I just pulled up a random page from a student paper, which has about seven fonts in use. The usage audit says they total a bit over 2mb.

Why Is "Export Small File Size" Large?

Hi, I work in CS3. Out of 100 brochures, I have two brochures that will not export to a small file size PDF. The settings for export are all the same. What else should I be looking for? The sizes are usually 1 MG. These particular 2 brochures are 5 - 6 MG. What can I look for to correct this?
Thanks

Small size is very dependent on the contents being exported to PDF. Images are readily compressed. Text and vector data isn't. Thus, if your content is primarily text and vector, it is very unlikely that the content can be compressed signficantly more via change of settings.
Another factor that can relate to image compression is use of any duotones that use spot colors. Such images cannot be JPEG-compressed, only ZIP-compressed.
- Dov

Lightroom 5 exporting wrong file sizes?

I am having trouble with Lightroom 5 exporting images at incorrect file sizes. For example, if I use my export preset for images with long edge 2500 pixels and maximum size 1000k it is exporting images at 1500-2500k.
Is anyone else experiencing this? I am wondering if it is a bug.
Thanks

I never had a problem with it in LR4. The example I gave was one of many options I tried. At the other end I asked it to produce smaller files (eg 1500pixels long edge) with a 1000k maximum and I could only get them to output at around 160k.
I have since realised that I neglected to mention that I was using LR/Mogrify2 plug in to add a text graphic to the images. I experimented with turning that option off and I was able to produce a 2500px long edge file at 996k. As soon as I turn that option on again the file ouptuts at 1600k (where I have specified at 1000k limit).
This was never a problem with LR4 so there is a conflict or a bug somewhere.
Is anyone else using a LR / Mogrify 2 plug in and experiencing unpredictable results? I have the option to use LR / Mogrify 2's version of ImageMagick checked.
Message was edited by: Shipp
So I just did further testing. It seems that LR5 cannot control the maximum file size when working with Lr / Mogrify 2. If I ask the plug in to resize the image and control the maximum file size I can produce a file with long edge 2500pix, 1000k maximum size and the text graphic with no problem at all, as I used to be able to do with LR4. I will contact the plug in developer and see if they are aware of this.

MP3 File Size in CS5.5 & CS6 Compared to AA3

Background.
I am the learning materials coordinator for a Barbershop Chorus and, during the qualifications process, members will email me a recording of their voice singing a song, while in the chorus, for which they have to note and word perfect for them to be qualified to perform that song with the chorus.
I use AA to convert the files they send me to the smallest high quality MP3 I can so they are easily listened to by the person receiving the file and the file size will be relatively small. Since this is a learning process ASCAP/BMI copyright issues do not apply (the Barbershop Harmony Society has verified this with them). With the advent of CS5.5 and, subsequently, CS6 the file sizes for a VBR, highest quality MP3, have grown to almost twice the size as before.
AA3, 2870k
CS6, 6034k
Obviously I'm still using AA3 for this conversion though I would like to standardize on the latest version of the software.
Any thoughts?

I performed a quick test comparing an 18 minute stereo file saved in CS6 and 3.0 as MP3, VBR, Highest Quality. The CS6-generated file was 28MB, while the 3.0 file was 22MB. However, Audition CS6 uses a newer compression kit that no longer supports Mp3PRO encoding. (Fraunhoefer no longer supports this scheme either, and I, personally, was never that impressed with the results.) Finally, the "Highest Quality" mode in CS6 encodes around 200Kbps while Audition 3.0 typically encoded around 163Kbps in Highest Quality mode.
I think you'll find a closer correlation between Au3 "Highest Quality" and CS6 "High Quality" VBR presets, when comparing the resulting file size. However, CS6 Highest Quality should sound better than Au3.

Exported JPEG file sizes

A number of my images exported to JPEG have a larger file size than the original RAW file. My export is fairly basic, quality 100, color space sRGB, no resizing, no watermark. Anyone any idea why ? I thought JPEG were supposed to be compressed.

Possibly because you are not setting an output resolution so light room is making a best interpolation.
Try setting the dimensions you want or the dimension for the long edge and use a resolution of 300ppi for printing or 72 for uploading to the web.

Export constrain file size

The lab my client uses doesn't like to handle jpegs larger than about 2MB. OK, that's their rule and I have to make it work.
In PhotoShop, when I converted to jpeg I could see how large a file it was going to produce. In LightRoom I don't know how to do that. I can choose a quality, which isn't measured in anything. And I can enter a dpi, which shouldn't make any difference if the pixel count is unchanged. There's no way to sort by size. So I guess and export them all, then check the sizes and go back again and re-export the files that are too large. Very Clumsy.
Can anyone advise me how to get these Canon 5D files to convert to jpegs at around 2MB?
-wick

Through trial and error (no help from LightRoom), I decided to contrain the file size to within a 2K by 2K pixel rectangle. This gives me roughly the right file size. thanks to all for your suggestions. In the end, of course, I either have to downsize the image or raise the compression to around 60 (as Ian suggested). In the end, assuming a print size no larger than 8 x 10, do you think the better solution is to downsize or upcompress?
-wick
PS: Has anyone else come across the bug mentioned in my second post, where exporting the same file over and over leads to the wrong file getting exported? Maybe LightRoom just got bored?

LR3 Export jpg File Size Inaccurate

I have a CR2 file 4752 x 3168 and 22.22 MB that I want to export to jpg. I select resolution of 72 with dimensions of 1024 x 683 (largest size of side is 1024) with a file limit of 150KB. I get a file that is 155 KB with the indicated dimensions/resolution. I set the maximum file size to 130 KB and get a file that is 155 KB. I have to set the limit at 100KB to keep the file size under 150KB. I can do the same thing in CS5 using the Save to Web without any problems.
It should not be that difficult to convert and resize an image for web imports limits.

Thank you. Maybe they will get everything corrected before they release 3.2 for production.
Regards,
Mike

Trace file size is huge

HI Experts,
In my production database one trace file alone getting created in huge size, could you please make me aware of the reason behind this and solution to this.
Path:/oracle/admin/proddb/bdump
proddb_j000_17828.trc /5G/
Regards,
Salai

You can limit trace file size using MAX_DUMP_FILE_SIZE db parameter if you have a free space problem too.
http://download.oracle.com/docs/cd/B19306_01/server.102/b14237/initparams116.htm#REFRN10103
But of course this wont solve your original issue. Try to analyze content of the trace file and try to solve the base issue.

Exported mp3 file size is huge!

Similar Messages

Maybe you are looking for