External List Webpart does not render after webpart page is checked in

Hello,
I've created an external list based on an external content type the list renders fine.
I have in turn created a webpart page and added the external list to the webpart page as well as a current user filter.
I use the filter to filter this list based on a column (username in the external list). I do all this within a publishing site (I don't know if that's contributing to the challenge I'm having).
before I check in and publish the page I observe the filters are applied
and it appears everything is ok. However after I check in the page and publish it the page doesn't render and the gears cycles on the page for ages
It's worked the first time I did it but I had to delete and recreate the page subsequently the page doesn't render and gears animation just keeps playing. Even with the filter disconnected from the webpart it still doesn't render. What could kindly be the
problem
thanks

Hi,
As I understand, you encountered the issue when you checked in and published the web part page.
If you do not have to use external list web part, you can change to use business data list web part in the business data. You can edit the web part and choose the external content type you want
to connect.
There is a similar case:
https://social.technet.microsoft.com/Forums/sharepoint/en-US/af76e3fd-99f8-4694-bae6-e9ee53d2e66e/external-list-in-publishing-page?forum=sharepointgeneral
Best regards
Sara Fan
TechNet Community Support

Similar Messages

External hard drive does not mount after sleep

I am using a brand new Seagate 2 TB external hard drive for my backup drive. More often than not, when the computer goes to sleep, the icon for the drive is gone from the desktop when the computer wakes up. I have to unplug it from the computer and reconnect it, then it mounts and works fine. I have it plugged directly into the computer's USB port. The drive uses USB3. As far as I can tell, it does not exceed the power requirements of the USB port. It is the only external hard drive I am using at the moment.
I should note that the same thing was happening with my last hard drive. That was a Western Digital 250 GB drive with an independant power source connected by firewire.
I am running OS 10.6.8 on an Intel circa 2009 iMac. My external drives worked fine for years, and it seems in the last year or so is when this started happening.

r_dizzle wrote:
Another point of note is that both the HD and the keyboard are connected to the iMac through a 7 port USB hub.
I think this might be the issue. If the iMac is waking back up, it will likely be waking up this HUB, but the HUB might not be re-initialising the connection between OS X and the external drive or the keyboard.
After waking the iMac, if you unplug the external drive from the HUB, then plug it back in again, does OS X pick it up again? Have you tried plugging the external drive directly into the iMac and then testing what the result is?
If you read back on what you've said, you pointed out that you have a USB mouse that you use to wake the iMac from sleep. Is this mouse directly connected to the iMac? If so, it surely can't be a coincidence that a directly connected USB device can wake the iMac from sleep, but any USB devices connected to the iMac via a USB HUB cannot.
I would suggest you test the drive as it is directly connected to the iMac. I would complete the same test with the keyboard too. I think you'll find it's the USB HUB.
I hope this helps.

External hard-drive does not reconnect after sleep

Hi everyone
I am trying to use my Energy Saver to SLEEP my iMac after 1 hour. It goes to sleep no problem, but on wake-up, my external USB hard drive does not reconnect. There is also an error message that I didn't disconnect the drive properly. I fear this may be one of Mac OS X's "features". Has anyone encountered the same thing?
On a side note, I also find that my USB keyboard does not always reconnect as well. I use a windows USB mouse that I have connected to wake it from sleep, however my USB keyboard (the small one for Macs), sometimes does not allow me to type unless I unplug it and back in.
Another point of note is that both the HD and the keyboard are connected to the iMac through a 7 port USB hub.

r_dizzle wrote:
Another point of note is that both the HD and the keyboard are connected to the iMac through a 7 port USB hub.
I think this might be the issue. If the iMac is waking back up, it will likely be waking up this HUB, but the HUB might not be re-initialising the connection between OS X and the external drive or the keyboard.
After waking the iMac, if you unplug the external drive from the HUB, then plug it back in again, does OS X pick it up again? Have you tried plugging the external drive directly into the iMac and then testing what the result is?
If you read back on what you've said, you pointed out that you have a USB mouse that you use to wake the iMac from sleep. Is this mouse directly connected to the iMac? If so, it surely can't be a coincidence that a directly connected USB device can wake the iMac from sleep, but any USB devices connected to the iMac via a USB HUB cannot.
I would suggest you test the drive as it is directly connected to the iMac. I would complete the same test with the keyboard too. I think you'll find it's the USB HUB.
I hope this helps.

External Hard Drive does not mount after connecting to airport

Hello,
I tried finding a solution to this problem already, but people that posted were having issues seeing the drive connected to the airport, while I am having the opposite problem.
After I tried connecting my USB drive my new airport extreme and it worked there and I tested speed and whatnot, I disconnected it and plugged it back into my iMac and now it will not show up anywhere, and will only show up when connected to the airport.
Basically I want my drive that was connected to the airport to connect to my mac again because it is not working.

Zerimar wrote:
After I tried connecting my USB drive my new airport extreme and it worked there and I tested speed and whatnot, I disconnected it and plugged it back into my iMac and now it will not show up anywhere, and will only show up when connected to the airport.
To clarify, when you connect that drive directly to your iMac it doesn't appear on the Desktop? Do you have Finder preferences set (in the General tab) to show "External disks"? Do you see the drive in Disk Utility?

Blog Archive Webpart Does Not List Posts When Publish Date is About early months,years in sharepoint 2013

I create blog posts . Their publish date are different from now and their publish date are the early months. For example i create 30 blog bosts in 15.08.2014. But 10 blog posts' publish date is 15.04.2013,20 blog posts' publish date is 15.03.2012. I can
not see them in the blog archive part. There must be April 2013 and March 2012 in the archive part,but i can not see them.
How can i see them in the blog archive webpart?
When i create a blog post, what is the main issue about the date? What is the main issue about date about grouping them.
How can i show the blog posts according to the publish date not create date? İs it possible?
Can you help me please?

It seems you created another thread for same issue. Let's wait for the response from original thread, instead of creating a new one.
http://social.msdn.microsoft.com/Forums/en-US/2a3f7d99-c74b-4554-94bf-e597a88b5425/blog-archive-webpart-does-not-list-posts-when-publish-date-is-about-early-monthsyears-in-sharepoint?forum=sharepointcustomization
My Blog- http://www.sharepoint-journey.com|
If a post answers your question, please click Mark As Answer on that post and Vote as Helpful

External USB keyboard does not work with T60 after BIOS upgrade

External USB keyboard does not work properly with T60 after 2.26-1.07 BIOS upgrade.
It does the same with or without the docking station.
Anyone else bumped into this problem yet?
Has someone found any fixes for this?
t

Hi and welcome the forum!
Try uninstalling all USB hub devices from the device manager and reinstalling them again, particularly the keyboard's.
v2.26 is supposed to fix the issue according to lenovo:- http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-63024
Hope it helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

After Effects CS5.5 does not render any type of file, corrupted message.

Hey guys,
About 2 days ago I was working on my file as usual (with no changes whatsoever to my software or hardware) and After Effects suddenly refuses to render my video and does not even go past one single frame, it will not render movies, image sequences, anything, it does not render period.
when I click on stop it gives me this message:
I have not changed any settings on my computer or After Effects and rendering this specific file worked fine before this random occurence a couple days ago, other files render work so something is wrong with this file specifically.
The project I am working on is a rotoscoping animation, I have used the Rotobrush on some MOV files, along with Particular Trapcode, and some effects such as Glow and Blur, nothing fancy.
Here's my technical info , hopefully it's enough detail:
After Effects CS5.5
Mac OSX 10.7.4
Memory 16GB 1333 MHz DDr3
3.1 Ghz Intel Core i5
MOVIE FILES INFO:
50fps
1280x720
h.264
Linear PCM
16-bit little-endian signed integer, 4800HZ (stereo LR)
File sizes range from 1.33Gb to 500mb (I can't compromise on quality as this is a big project)
Is there anything else you need to know? my deadline was yesterday and this is for a live show next week, any help would be greatly appreciated.
Also audio's not a big deal as I'm not using it, here are some screenshots of my project settings.

At first the problem came back but then I disabled the 'media cache' option in Preferences as advised above, seems to work for now.
I keep having to turn this option on and off if I want it to render, there must be some way around this.

Render engine does not stop after reaching 100%

It looks like to me that the render engine does not stop after reaching 100%. It does not affect the rendered file which is fine and complete
-the Pause and Stop buttons are displayed but have no effect on pausing or stoping the render
-when I want to quit SG, it locks up and have to Force Quit to get out of it.
I really like the program though and hope you are going to fine tune the UI and make it look like After Effect and Premiere.
I would encourage you to instaure round tripping between these two apps and SG.
It would be nice to have curves as well.
Thanks guys
Brice

Could you open the defaultTrace.X.trc files and check for the errors?
Good from my point of view is to make a search if those files for some stack traces with the string ".dsr."
Regards,
Aleksandar

My mac mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone

My Mac Mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone. I had switched the start-up disk back to the original of course. Now all I see is the Apple logo. What should I do? Thanks in advance.

Try disconnecting any external devices, especially hard drives
and try rebooting.
If that doesn't help, then :
If you are running Lion, boot to the Recovery HD and run a
Repair Disk on the OSX partition.
If Snow Leopard, boot to the installl DVD and run Repair Disk.
Also, you may want to bookmark this:
http://reviews.cnet.com/8301-13727_7-57345273-263/troubleshooting-the-boot-proce ss-for-intel-macs/?tag=txt;title
for future reference. It is a pretty good explanation of the
Mac boot process and how to identify where problems may be.

Time Machine does not start after external hard drive is connected

Time Machine does not start after external hard drive is connected

These are the iCloud storage options: http://www.apple.com/icloud/includes/lightbox-storage.html
Also bear in mind that:
1. restoring data over icloud takes time
2. iCloud is not designed as a replacement to Time Machine.

IOS 7 app store update list does not clear after updates have been installed

iOS 7 app store update list does not clear after updates have been installed

Rifles wrote:
Good point, we will have to wait and see, it's a pity Apple has not produce an IOS7 PDF
You mean like this one?
http://manuals.info.apple.com/MANUALS/1000/MA1565/en_US/iphone_user_guide.pdf
Best of luck.

External USB HD does not work with HAL:

External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.

I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era

TX2500Z touchscreen does not work after Windows7 upgrade from HP specific to S/N, etc on laptop.

My TX2500Z touchscreen does not work after I upgraded to Windows 7. I cannot find any support or drivers, etc. to fix. I bought Windows 7 directly from HP specific to my P/N and S/N on my TX2500Z. Any help? Thanks.

after 2,5 days (spending half a day within the apple shop as well with this problem) i have it all back on track.
i did a lot of different things: trying to remove and reinstall iPhoto; did a SL installation over the old SL I had on my HD; backing up all the data of course before and reformatting my HD and installing a new clean SL version on it + a new clean version of iLife9 with all the updates and than I migrate with migrate assistant all the data and setting with time machine back onto it, but all this didn't work, because it also migrated the error/bug through time machine with it.
so at the end i just installed a brand new, clean SL version on my hard drive, than I did the updates and put all my data, photos, docs, movies, mail, bookmarks, music, etc manual back into the system (drag and drop from my external HD, where i had an exact copy of my internal HD) and did all the settings again in all the different programs.
the only thing i used migrant assistant with time machine for was for the programs. it seems to work now all fine and i even got more free space on my HD, because some of the old stuff i always carried with me but i never used, i didn't take over.
basically everything is clean now. At least i hope and works fine. touch wood!

RAC does not start after trying to move storage

Hello,
We have a two nodes RAC Oracle 10g and ASM groups defined on one external storage.
RAC does not start after we reformated the storage to RAID 10.
What we did:
1) deleted the database
2) reformated the external storage to RAID 10 and defined needed volumes for OCR, VotingDisk and ASM
3) on both nodes
- recreated VotingDisk
node1:root$ /u01/oracle/product/10gr2/crs/bin/crsctl add css votedisk /dev/rdsk/c0t600A0B8000347E7D00000EE74A5AF386d0s3 -force
Now formatting voting disk: /dev/rdsk/c0t600A0B8000347E7D00000EE74A5AF386d0s3
successful addition of votedisk /dev/rdsk/c0t600A0B8000347E7D00000EE74A5AF386d0s3.
node2:root$ /u01/oracle/product/10gr2/crs/bin/crsctl add css votedisk /dev/rdsk/c0t600A0B8000347E7D00000EE74A5AF386d0s3 -force
Now formatting voting disk: /dev/rdsk/c0t600A0B8000347E7D00000EE74A5AF386d0s3
successful addition of votedisk /dev/rdsk/c0t600A0B8000347E7D00000EE74A5AF386d0s3.
- tried to move OCR but was able only on one node:
/u01/oracle/product/10gr2/crs/bin/ocrconfig -replace ocrmirror /dev/rdsk/c7t30d0s3
/u01/oracle/product/10gr2/crs/bin/ocrconfig -replace ocr /dev/rdsk/c7t29d0s3
/u01/oracle/product/10gr2/crs/bin/ocrconfig -replace ocr
These return ok for both node1 and node2:
node1:oracle$ cluvfy stage -post hwos -n node1
node1:oracle$ cluvfy stage -post crsinst -n node1,node2 -verbose
Performing post-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "node1"
Destination Node                      Reachable?
node1                                 yes
node2                                 yes
Result: Node reachability check passed from node "node1".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name                             Comment
node2                                 passed
node1                                 passed
Result: User equivalence check passed for user "oracle".
Checking Cluster manager integrity...
Checking CSS daemon...
Node Name                             Status
node2                                 not running
node1                                 not running
Result: Daemon status check failed for "CSS daemon".
Cluster manager integrity check failed.
Checking cluster integrity...
Cluster is divided into 2 partitions.
Partition 1 consists of the following members:
Node Name
node1
Partition 2 consists of the following members:
Node Name
node1
node2
Cluster integrity check failed. Cluster is divided into 2 partition(s).
Checking OCR integrity...
Checking the absence of a non-clustered configuration...
WARNING:
CSS is probably working with a non-clustered, local-only configuration on nodes:
node1
Verification will proceed with nodes:
node2
Uniqueness check for OCR device passed.
Checking the version of OCR...
OCR of correct Version "2" exists.
Checking data integrity of OCR...
Data integrity check for OCR passed.
OCR integrity check failed.
Checking CRS integrity...
Checking daemon liveness...
Check: Liveness for "CRS daemon"
Node Name                             Running
node2                                 no
node1                                 yes
Result: Liveness check failed for "CRS daemon".
Checking daemon liveness...
Check: Liveness for "CSS daemon"
Node Name                             Running
node2                                 no
node1                                 no
Result: Liveness check failed for "CSS daemon".
Checking daemon liveness...
Check: Liveness for "EVM daemon"
Node Name                             Running
node2                                 no
node1                                 yes
Result: Liveness check failed for "EVM daemon".
Liveness of all the daemons
Node Name     CRS daemon                CSS daemon                EVM daemon
node2         no                        no                        no
node1         yes                       no                        yes
Checking CRS health...
Check: Health of CRS
Node Name                             CRS OK?
node1                                 unknown
Result: CRS health check failed.
CRS integrity check failed.
Post-check for cluster services setup was unsuccessful on all the nodes.
Please help.

Thanks for the answer.
Problem is that the RAC is not healty, I know how to start it but now it doesn't start and I cannot find helpful logs.
You can see that cluster is not healty from cluvfy output.
When I tried to start crs whith crsctl start crs but:
- on node2 none of the demons starts (CSS, CRS or EVM)
- on node1 CSS and EVM demons start but CRS is not starting and I cannot find helpful logs
Problem 2: Cannot change OCR location
node2:root$ cat /var/opt/oracle/ocr.loc
+#Device/file /dev/rdsk/c7t30d0s3 getting replaced by device /dev/rdsk/c7t30d0s3+
ocrconfig_loc=/dev/rdsk/c7t30d0s3
local_only=falsenode2:root$ ocrconfig -replace ocr /dev/rdsk/c0t600A0B8000347EAD00000F314A5AF5B8d0s3
PROT-1: Failed to initialize ocrconfig
node1:root$ cat /var/opt/oracle/ocr.loc
ocrconfig_loc=/u01/oracle/product/10gr2/db/cdata/localhost/local.ocr
local_only=TRUE
node1:root$ ocrconfig -replace ocr /dev/rdsk/c0t600A0B8000347EAD00000F314A5AF5B8d0s3
PROT-1: Failed to initialize ocrconfig
Problem 3: On node 1 I wrongly issued a command
node1:root$ /u01/oracle/product/10gr2/db/bin/localconfig reset
Successfully accumulated necessary OCR keys.
Creating OCR keys for user 'root', privgrp 'root'..
Operation successful.
Configuration for local CSS has been initialized
Adding to inittab
Startup will be queued to init within 30 seconds.
Checking the status of new Oracle init process...
Expecting the CRS daemons to be up within 600 seconds.
Giving up: Oracle CSS stack appears NOT to be running.
Oracle CSS service would not start as installed
Automatic Storage Management(ASM) cannot be used until Oracle CSS service is started

Game does not start after installing on mac pro

Game does not start after new install on mac pro ?

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Click the Clear Display icon in the toolbar. Then try the action that you're having trouble with again. Select any messages that appear in the Console window. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V).
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.

External List Webpart does not render after webpart page is checked in

Similar Messages

Maybe you are looking for