Extreme slowness with Juniper Network Connect

Hi there,
I recently switched from cable modem to fios and I am very frustuated with fios as the company vpn speed slows down gradually (while I never had any issue with cable modem) to 0.5 mbps from 50 mbps in a few hours. I often try restarting modem and reconnecting which helps sometimes. My company IT reported no problem and my colleagues on cable also report no problems with vpn. My desktop is directly connected to the cable modem via wire (not wireless).
I would appreciate any suggestions.
Thank you,

While this is not a Windows 10 specific issue (it happens in Windows 8.x, too), I wanted to discuss it here to see there was a solution.
When using either of my corporation's two VPN options, Juniper Network Connect and Juno Pulse, I cannot use any Modern apps that have network access. BUT, this does not seem to effect Microsoft's Modern apps, like Mail or the Store.
As an example, Nextgen Reader, cannot synch with Feedly when I am connected to the VPN, but it works fine otherwise.
Yet, I can synch my OneNote notebooks or I can visit the Windows Store, so it doesn't seem to be strictly a problem with the VPN software.
Does anyone know of a work-around for this? Is this something that can be better addressed in Windows 10 so this is no longer an issue?
Do you you the VPN in Windows settings or install a client. My organizations info-structure won't allow to connect using the VPN built into Windows 8/10. In Windows 8 i installed the client and enter my companies connect information and it works. But the
same thing doesn't work in Windows Technical Preview.
Jake

Similar Messages

X200 WWAN (f3507g) compatibility issue with Juniper Network Connect VPN

I have just recently received my X200 with the build-in WWAN which is a Ericsson f3507g card and found that it causes my Juniper VPN software unable to load, and I have also noticed other applications like Outlook is rather slow. When I "Disabled" the WWAN card in "Device Manager"->"Network Adapters", all apps work perfectly. I am using 32-bit Vista Business.
Can someone test and see if you have the same problem as mine? I am wondering if this is a driver issue of the f3507g WWAN card.

Hello
I have just spent all day trying to work out why Outlook takes forever to connect on initial start. It was purely by luck/perseverance that I happened to notice an "ipconfig" stuck for a second on LAN2 - which is the ericsson card.
I too then disabled this adapter and found Outlook performance cured. I had popped along to these forums to find a fix but at least I can verify the issue with you.
Bloody annoying since I've only had the X301 1 day - I bought it for use whilst my X300 is having its wireless-freezing issue sorted. Not a good advert for Lenovo I think.

Snow Leopard and Juniper Network Connect/How to temporarily disable Bonjour

Hi All,
I have encountered a problem with Juniper Network Connect running on my MacBook Air. I can connect successfully to my company's VPN but on my MacBook Air Junipers Network Connect started to dis- and reconnect in changing time intervals.
After some googling I am pretty sure that it has something to do with the Bonjour service changing the routing tables. I wanted to confirm this and activated "Back to my mac" on my MacBook Pro which up to now did not had any problems connecting to my company's VPN. Now it has the same issues.
My question is whether there is any way to temporarily disable Bonjour, ideally via Apple script. Up to now the only solutions I found were to either
- disable mDNSResponder which would also prevent accessing any websites or
- disable multicast advertisements (http://support.apple.com/kb/HT3789?viewlocale=en_US)
The latter approach includes editing a properties file and restarting the mac, thus would be less than ideal for just quickly dis- and enabling bonjour. Furthermore I am not quite sure whether this really solves the problem of updating the routing table.
Any advise is greatly appreciated.
Thanks,
equinox

If you are using an Airport or Airport Express base station: go to Utilities>Airport Utility. When it's found the Airport, click on 'Manual Setup'. In the next pane, click on the 'Wireless' tab; when that pane opens click on 'Wireless Network Options...'. Check 'Create a closed network'.
If you are using another manufacturer's wireless router you will need to look at their instructions, but the principle is the same - it may say something like 'Hide SSD'.

After Safari 7.06 update, whenever I connect to RSA Juniper Network Connect, my internet connection get disconnected. It was an issue with old Safari versions. It was fixed around 6 months back with one of Safari update. But, now it is broken again.

After Safari 7.06 update, whenever I connect to RSA Juniper Network Connect, my internet connection get disconnected. It was an issue with old Safari versions. It was fixed around 6 months back with one of Safari update. But, now it is broken again.
Anybody experiencing the same problem and any suggestions to fix the issue.

Hi ..
Try this discussion > Can't connect to Juniper VPN

Juniper Network Connect Support with Fusion

Hi, I'm trying to run Juniper Network Connect in my W7 partition using VM Ware Fusion, but I get the following error: nc.windos.app.24043 (a NC client is already configured on the client). Has anyone solved this?

Hi BDAqua, thank so much for see my post.
My path is /Applications/Symantec Solutions/Norton AntiVirus
Thanks again
Alex

Juniper Network Connect broken in IE 10

Windows 8 x 64 Pro.... IE 10 has broken my VPN which uses Juniper Network Connect 7.1.8 are there any fixes on the horizon? Anybody know? Anybody have the same problem?
Thanks,
Rick
Rick

Hi,
Seems a software compatibility issue with Windows 8. I suggest you contact Juniper support for help since this involves 3rd party application.
Juke Chou
TechNet Community Support

Extremely slow internet and staying connected

I got Verizon internet almost 2 weeks ago. Ever since then it has been nothing but one problem after another. It cuts out so many times a day. I have to reset the modem 20+ times a day. Its very frustrating. I tried talking to customer service about it and they dont do anything, all they say is to go to the troubleshooting page and look around on there. I am ready to cancel because it is getting ridiculous. My modem is the Actiontec GT784 and it has built in Wifi, which cuts out as well. And the speed of the internet and the Wifi is extremely slow when it is connected. SOMEONE HELPPPPP!!!

Bad timing to get FIOS, There's an outage and Verizon doesn't seem to be doing anything.
http://www.dslreports.com/forum/r27957080-Problem-with-Fios

My computer is extremely slow, with the rainbow wheel appearing with every click. It is one year old, and has all the most recent updates. Why is it so painfully slow?

My computer is extremely slow, with the rainbow wheel appearing with every click. It is one year old, and has all the most recent updates. Why is it so painfully slow?

That sounds horrible. There are a number of reasons it could occur.
The first thing to do is ensure you have adequate backups, because what you describe can be a symptom of impending disk failure.
To help determine the possible causes of this behaviour read the following. None of what follows is intended to fix anything, but it will provide the additional information required to advance troubleshooting. There are four separate parts to it; read everything first.
Boot OS X Recovery by holding ⌘ and r (two fingers) while you start your Mac. At the Mac OS X Utilities screen, select Disk Utility. Select your startup volume (usually named "Macintosh HD") and click the Repair Disk button. Describe any errors it reports in red. If Disk Utility reports "The volume Macintosh HD appears to be OK" in green then you can be reasonably (though not completely) assured your hard disk is in good working order.
When it finishes restart your Mac and test again for operation. If it's still not behaving as you expect it should, please post the results of EtreCheck in accordance with the following instructions:
Apple Support Communities contributor etresoft wrote a very useful app to quickly gather certain system information that may help point to a cause of this problem. Read about it here. It contains a link to download EtreCheck. Don't download it from anywhere else (such as may be found by following the results of an Internet search).
Click Open - etresoft contributes to this forum frequently and can be considered a trustworthy developer.
It will take a moment to run as it collects its data.
Copy and paste its output in a reply.
Do not be concerned about anything that says "Problem" or “failed” or anything else that may appear in red.
EtreCheck was designed to remove any personal information (such as your computer's name and serial numbers) but if you see anything that looks like an email address or any other personal information that should not be divulged to others, please delete or obscure that information when you post the reply.
When you are finished with EtreCheck, quit the program. It occupies very little space, and you can keep it or drag it to the Trash as you wish.
After completing the above please determine if the problems also occur in "Safe Mode":
Safe Mode or "Safe Boot" is a troubleshooting mode that bypasses all third party system extensions and loads only required system components. Read about it: Starting up in Safe Mode
You must disable FileVault before you can start your Mac in Safe Mode.
Starting your Mac in Safe Mode will take longer than usual, graphics will not render smoothly, audio is disabled on some Macs, and some programs (iTunes for example) may not work at all.
Merely starting your Mac in Safe Mode is not intended to resolve the problem, it's to observe its performance without certain additional components.
To end Safe Mode restart your Mac normally. Shutdown will take longer as well.
System performance problems for reasons that cannot be isolated to any other cause justify an SMC reset. Be sure to read the procedure carefully and follow all the steps exactly as written, even if they seem inapplicable or trivial.

My phone doesnt show incoming call and it doesnt ring. Further the iphone4 is extremely slow with opening whats app, camera and photos or while in the program it just closets. Who can advice me what to do??? Otherwise this phone will be changed soon

My phone doest ring with incoming calls, but it also doesnt show someone is calling. I only see it, when i get the txt of missed calls.
Further the phone is extremely slow with opening whats app, emails, photos, camera and it closets the programs while using it.
I have many people around me with iPhone having the same complaints, but nothing has changed yet.
Please Apple solve this quickly otherwise the iPhone i enjoyed so much will be remplaceren with a Samsung

esme43 wrote:
... the phone is extremely slow with opening whats app, emails, photos, camera and it closets the programs while using it.
See this discussion...
https://discussions.apple.com/message/23731048#23731048

HT5538 My facetime and imessage aint working now, when i try to turn it on, it says waiting for activation then when it finishes it says something to do with a network connection. help me!!!

My facetime and imessage aint working now, when i try to turn it on, it says waiting for activation then when it finishes it says something to do with a network connection. help me!!!

iOS: Troubleshooting FaceTime and iMessage activation

Juniper Network Connect fails in Mac OS 10.10

Hello,
I am trying to use Juniper Network Connect on my MacBook Pro running OS 10.10 and Java 8 (Update 25) to connect to my corporate network.
However, each time I log into my corporate network through Mozilla Firefox and attempt to establish a remote desktop connection the following message appears as Network Connect attempts to load, "An error occurred while extracting one of the Network Connect components."
Mozilla Firefox is recommended by my company.
Has anybody else experienced this issue?
I have encountered Network Connect problems over the years (and similar error messages) and I am wondering if this message is related to OS and/or Java upgrades?
Regards,
Ben

https://coderwall.com/p/_gpxpq/workaround-for-failing-juniper-network-connect-in -yosemite
Text of site:
The current version 8.0.7 of Network Connect and the latest Yosemite 10.10.1 don't like each other: you simply can't connect.
A workaround (and it should be nothing more if you care) is to allow unsigned kernel extensions (which are unsupported/disabled in Yosemite by default):
sudo nvram boot-args="kext-dev-mode=1"
(reboot afterward) To revert this:
sudo nvram -d boot-args
Looks like this is also helpful for some other problematic extensions.

Dreamweaver has been running extremely slow with reflow.css.

Dreamweaver has been running extremely slow with reflow.css. Wondering if anyone else is encountering this issue? If so, any fixes or known variable that causes this to happen?

I haven't see this. Can you describe a little more about what you are doing and what parts are slow? If there are specifc steps you can also file a bug with the Dreamweaver team:
https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform&product=12

I can't sign into face time. My account has been verified and I have full wifi signal but it comes up with check network connection how to i fix this?

I can't sign into face time. My account has been verified and I have full wifi signal but it comes up with check network connection how to i fix this?

What IP does your iPad show as having?
Try a reset. Press & hold the Power and Home buttons together for 10+ seconds, ignoring the red power-off slider, until you see the Apple logo.
Some folks have discovered that changing their DNS service fixes FaceTime connection issues.
The ideal way is to configure your modem/router with DNS service, but often settings in System Preferences/Network on your Mac will override the router settings. Try either of these;
OpenDNS
208.67.222.222, 208.67.220.220
Google Public DNS
8.8.8.8. 8.8.4.4

PC running extremly slow with iTunes

Hello all,
Question is why my laptop would be running extremly slow with cover flow when it has more than enough horsepower to run almost any application (2.33 dual core, 512 graphics card, 2gig ram). iTunes runs just fine on my work laptop with cover flow, and its specs arent on par with my personal laptop. The only difference i can think of is that the work laptop (the good one) is running xp pro and the home is running vista 32bit. the other difference i can think of is that at home, all the music is stored via external HD while on the work laptop the files are stored locally on the laptops hard drive.
any advice would be greatly appreciated
Cheers!

Vista has been reported to be a bit more buggy/laggy/unstable with iTunes. Music running of an external will also be noticeably slower and more jumpy than running off an internal. You answered your own question.

Mac OSX 10.7.5 + Java 7.11 Juniper Network Connect fails

I am running Mac OSX 10.7.5 and just upgraded to Java 7.11. As a result, my Juniper Network Connect vpn now fails - I can't even install the software. I see the following error message "An error occurred while extracting one of the Network Connect components." I made sure the keystore password was set to changeit using the following:
sudo keytool -storepasswd -new changeit -keystore /System/Library/Frameworks/JavaVM.framework/Resources/Deploy.bundle/Contents/Home/lib/security/cacerts -storepass changeme
However, I continue to see "An error occurred while extracting one of the Network Connect components."
Any ideas?

retrana wrote:
I made sure the keystore password was set to changeit using the following:
sudo keytool -storepasswd -new changeit -keystore /System/Library/Frameworks/JavaVM.framework/Resources/Deploy.bundle/Contents/Home/lib/security/cacerts -storepass changeme
However, I continue to see "An error occurred while extracting one of the Network Connect components."
Just a guess, but that looks to be the location for Apple Java 6, which is not replaced when you upgraded to Java 7, rather Oracle stores it in a different location.
It's also possible that Juniper has not updated their software for Java 7. I know that's true for at least one other VPN vendor.

Extreme slowness with Juniper Network Connect

Similar Messages

Maybe you are looking for