F110 run the payment run directly without running the proposal run first

Hello to you all,
Does any one know I do I block the option to run the payment run directly without running the proposal run first?
Thanks in advance,
Yoav

Hi
First delete the payment run output by the following :
Goto Edit on menu bar --> Payment --> Delete Output
then run the proposal run again and after that process payment run.

Similar Messages

  • Can i run a printer off the ethernet cable connection without hurting the imac or is the ethernet slot only for internet connection?

    can i run a printer off the ethernet cable connection without hurting the imac or is the ethernet slot only for internet connection?

    Hi, Alan -
    How can I connect to both printer (HP 4050n, via direct connection) and internet (via LAN), as my iMac has only one R45 port?
    You can, but you'll need to expand your cabling a bit.
    You'll need to get an intermediate ethernet hub, switch, or router. That device sits alone, with the Mac, your printer, and your modem/LAN plugged into it.
    If you are already using a router, either separate or in combination with the modem (many modems have a built-in router), then you just need a hub or switch.
    I use an ethernet switch (10/100/1000) to let both my Macs (a 2010 iMac and an elderly G4 DA model) use my HP4000n printer and my modem. The ethernet switch is a passive device, meaning there's no setup nor instructing it required - it's truly plug-and-play. All four items (two Macs, printer, and modem) are plugged into it via ethernet; both Macs have full-time independent access to the printer and the modem.

  • I have just updated my 4s to IOS7. and now my battery discharge is significantly increase. With my Iphone fully charged, the battery run out within 6 hours without using the phone at all. Would it be possible to get the IOS 6.1.3 back to my 4S?

    I have just updated my 4s to IOS7. and now my battery discharge is significantly increase. With my Iphone fully charged, the battery run out within 6 hours without using the phone at all. Would it be possible to get the IOS 6.1.3 back to my 4S?

    Hi, thanks for the suggestion. I have tried as you suggested, and when opening the "purchased" apps some have the icloud logo next to them, but I only have "OPEN" against "Find My iPhone". When opening it up, it goes through the same routine; needs to be updated before proceeding, and wouldn't update because I don't have IOS8.
    Anything else I could try, or am I doomed!
    All of your help is much appreciated, thanks

  • I have an old project with AVCHD clips and I want to import the clips again with surround sound. How can I relink the project clips to the re-imported ones without doing the project from the begining?

    I have an old project with AVCHD clips and I want to import the clips again with surround sound. How can I relink the project clips to the re-imported ones without doing the project from the begining?
    I have a sony handicam and I imported the clips to iMovie and they lost quality and converted the audio to stereo. I want to import the project to final cut X and import the AVCHD in 1080p and surround sound and export the movie in bluray. Can I relink the clips without editing everything again?
    thanks!

    Only photos taken with the iPad, copied onto it via the camera connection kit, or saved from emails/websites etc can be deleted directly on the iPad - either via the trashcan icon in the top right corner if viewing the photo in full screen, or via the icon of the box with the arrow coming out of it in thumbnail view.
    Photos that were synced from a computer are deleted by moving/removing/de-selecting them from where they were synced from and then re-syncing. If you want to remove them all then normally you could just sync an empty folder (in terms of photos) to the iPad, but as you don't want to sync at the moment you can't do that.
    You can reset the iPad back to factory settings and start from scratch with it : Settings > General > Reset > Erase All Content And Settings

  • The payment request do not transfer the Item Text field to FI doc

    The payment request do not transfer the Item Text (SGTXT) field to FI documents (accounting document) when they are paid by F111 and the payment request is created from repetitive codes (Trx FRFT_B). Therefore is not able to display a text description in the FI line items accounts, even the payment request document number is not available in the accounting document.
    Even the program SAPLKKBL (F8BT) does not contain available the Accounting document.
    So, there is not easy trace.
    Does anybody know how can I match this?

    This is the SAP Response:
    Dear customer,
    The standard FRFT_B transaction does not directly or indirectly pass
    the text to the F111 payment document since the initial program design.
    In other words, you will not able to experience the reported issue
    in the system with standard SAP coding.
    However, the text value can be passed via business transaction event
    (BTE) for example or other modifications as a substitution.
    I hope this confirmation of the standard system behaviour is
    useful to you.
    I regret not to be able to give you a positive answer.

  • How we can limit the number of concurrent calls to a WCF service without use the Singleton pattern or without do the change in BizTalk Configuration file?

    How can we send only one message to a WCF service at a time? How we can limit the number of concurrent calls to a WCF service without use the Singleton pattern or without do the change in BizTalk Configuration file? Can we do it by Host throttling?

    Hi Pawan,
    You need to use WCF-Custom adapter and add the ServiceThrottlingBehavior service behavior to a WCF-Custom Locations.
    ServiceThrottlingBehavior.MaxConcurrentCalls - Gets or sets a value that specifies the maximum number of messages actively processing across a ServiceHost. The MaxConcurrentCalls property specifies the maximum number of messages actively
    processing across a ServiceHost object. Each channel can have one pending message that does not count against the value of MaxConcurrentCalls until WCF begins to process it.
    Follow MSDN-
    http://msdn.microsoft.com/en-us/library/ee377035%28BTS.10%29.aspx
    http://msdn.microsoft.com/en-us/library/system.servicemodel.description.servicethrottlingbehavior.maxconcurrentcalls.aspx
    I hope this helps.
    Rachit
    If this answers your question please mark it accordingly. If this post is helpful, please vote as helpful by clicking the upward arrow mark next to my reply.

  • To split the payment document value as per the line items of the P O

    To split the payment document value as per the line items of the purchase order in the period of payment, so that the payment  amounts are measured against the Capex order assigned as account assignment in the purchase order.(Account assignment tab for the individual line item in the PO.
    Example:
    Inputs:
    Purchase Order 3100012345, line item 10 value 6000 line item 20 value 4000
    VAT @10% , account assignment for PO line item 10(Internal Order no 10001) & line item 20  Internal  Order 10002) G/ R no 5105105101 for Rs10,000.
    The I/R doc 501501501 appears as follows: (MIRO)
    Line 10: Value       Rs   6,000
            20: Value      Rs   4,000
    VAT                         Rs      600
                           Rs      400
    Total                       Rs11, 000
    Withholding Tax Rs 1,100
    The accounting entry for MIRO happens as follows: doc 2102102101
    GR/IR Dr      Rs 10,000
    VAT      Dr     Rs   1.000
    Vendor    Cr           Rs9, 900
    TDS due   Cr          Rs1, 100
    The business expects the payment report as follows:payment  doc 2001200101
    PO     Line item       Internal Order MIRO         Invoice                       Payment       Payment period  Amount
                                                                                    A/c doc number        doc number          
    3400012345     10     10001           5605605601  2102102101           2001200101       001/2009           5940
    3400012345     20     10002     5605605601     2102102101           2001200101        001/2009          3960
    Currently we are able to show the amounts as Rs 6000 for line item 10 & Rs 4000 for line item 20.
    The problems faced.
    1.     The VAT line items are auto created, hence the reference of purchase order number and line item are not available. So the VAT portion which is part of payment liability does not get reflected against the PO.(not able to show the VAT portion , when we try to show the payment amount per PO line item.)
    2.     The withholding tax is also a problem; WHT is not calculated and assigned per line item. It is calculated on the total amount of basic and VAT. Because of these reasons, the payment could not be shown properly according to the line item of the purchase order.
    3.     When part payment is made, against invoices, there is no provision to assign a payment amount against a particular line item. Further, when final payment is made in different period, the clearing document will get generated. That adds to the complexity of differentiating full payments and part payments final clearing.
    4.     When residual payment is made, a new line item is created. Here assignment of Purchase order line item against payment for residual items become a problem.
    5.     Many a times advance payments are made. Later the invoice is created and balance payment is made. In those situations, the clearing document creates one more line item and makes payment for the balance item. This adds complexity in bringing balance payment alone and to split as per the purchase order line item. The clearing document number system is multi dimensional. It creates two line items for the same item (one at the time of advance and another the time of clearing.)
    6.     When full payment is made, the payment document number and clearing document numbers are same. In cases of subsequent or partial or residual payment, the document numbers are different. Because of this, the part payment amounts are shown in the period, where the final payment and clearing are made.
    Please suggest a way to split the payment amount in the exact posting period with all the considerations given above.
    Regards
    Sundararajan
    Edited by: Sundarajan Venkatachari on Sep 30, 2009 11:04 AM

    Hi,
    See Note 301077 - User exits for the interface to accounting, although I think that there isn't this kind of option. Note 429117 - Collective note advice note SD-FI interface will be useful too.
    I think that SAP Note 1085921 - Document split perhaps will help you
    Regards
    Eduardo

  • Computer iMac7,1 has been giving sundry problems for some time. Within the last six weeks I have reinstalled the OS (Snow Leopard), without affecting the overall contents of the hard drive. ±3 weeks later the problems became more serious and I again reins

    Computer iMac7,1 has been giving sundry problems for sometime. Within the last six weeks I have reinstalled the OS (Snow Leopard),without affecting the overall contents of the hard drive.
    ±3 weeks later the problems became more serious and I againreinstalled the OS and installed OS 6.6.7 from the internet.
    I used the option to restore from the external backup driveand went back some time as it was my intention to reinstall individualcomponent in an attempt to find out where the problem might lie. This hasintroduced an entirely new problem! If I open Time Machine from the desktop itappears that all backups from late 2009 to June 2011 are intact. But, in thiscase there are none of the restore functions &c on screen. The latter areonly shown if Time Machine is opened from the menu bar or from the dock but, inthis case, available are only backups in late 2009!
    I also opened the Apple Hardware Test in an attempt toestablish the nature of the problem. The ‘quick’ version said there’s nothingwrong; the more detailed one reported “Error detected, 4HD/11/40000004.” I haveagain tried to employ this test but nothing I do can induce it to open!!!
    What to do? I need help urgently and would appreciate anyadvice that offers solutions to the problem.

    To check your S.M.A.R.T status open disk utility and click on your drive and then click on the info icon.

  • How can I transfer music from my old iphone 4 to the new iphone 5S without having the music synced to my laptop (e.g. my itunes library is empty)?

    How can I transfer music from my old iphone 4 to the new iphone 5S without having the music on the old phone synced to my laptop (e.g. my itunes library on the laptop is empty) ?
    I tried the "Transfer Purchases" option - however this only worked for apps - not sure if I'm missing some sort of setting.
    I do not want to use iCloud as I do not have enough space for my music.
    Thanks!

    You cannot. The music must be in the iTunes library first. See these User Tips:
    Recover your iTunes library from your iPod or iOS device
    Syncing to a "New" Computer or replacing a "crashed" Hard Drive

  • I want to change the payment mode to credit card the problem that am still having some cents in my account how i can fix it ?

    I want to change the payment mode to credit card the problem that am still having some cents in my account how i can fix it ?

    You need to contact Apple so they can zero out the balance for you >  Contacting Apple for support and service

  • Manually set up the essbase 11 client (without using the fusion installer)

    Hi All,
    is it possible to install the Essbase 11 client without using the Fusion Installer?
    I tryed to copy the "bin" and "locale" directory from an exisiting installation and set up the ARBORPATH environment variable - without success.
    Did I miss anything? Maybe some Registry entries? Or isn't it possible to set up the essbase client manually?
    Every answer would be appreciated.
    Cheers,
    Martin

    Hi John,
    thanks for the hint that the addin is also available for any version.
    I have an application which uses the C-API (essapinu.dll, essotlnu.dll, ...) and I want to test it with diffrent Essbase Client Versions against diffrent Essbase Servers.
    These are the (client) versions which I want to test:
    EssbaseRtc11110WindowsFiles
    EssbaseRtc11111WindowsFiles
    EssbaseRtc11112WindowsFiles
    EssbaseRtc11113WindowsFiles
    EssbaseRtc9203WindowsFiles
    EssbaseRtc9210WindowsFiles
    EssbaseRtc9301WindowsFiles
    EssbaseRtc9310WindowsFiles
    I hoped it would be enough to replace some directorys on a machine instead of starting a lot of installers.
    Cheers,
    Martin

  • How do i find out what the IEMI number is without having the phone or package?

    how do i find out what the IEMI number is without having the phone or package?

    If you ever backed your iPhone up to your computer, launch iTunes, go to the Preferences, select Devices, and hover your cursor over the backup file for the iPhone. That should show you the IMEI number.
    If not, and you don't have the phone nor the packaging, you'll need to call your cell carrier and see if perhaps they can tell you.
    Regards.

  • How to keep the watch to display without press the button on my iPod Nano 6th)?

    Dear Guys,
    I have purchased a watchband for my ipod nano 6th recently, overall is okay but i don't know how to keep the watch to display without pressing the sleep/resume button on edge? Also, the screen is not showing the watch immeditaly when I press the button, it shows the music/cd folder, then I need to scroll the screen back to the watch display.  Please help.

    There is no way to keep the display on permanently, as doing so would significantly reduce the overall life of the battery.  It would maybe last only hour, maybe not even.
    As for having your iPod wake up to the watch view, head to Settings -> General -> Time on Wake -> On.
    B-rock

  • I recently moved into a new apartment and I can connect with the internet by direct connection to the cable/internet modem.  But when I connect my Airport Express, it just blinks with a yellow light and I cannot connect via WiFi.  Any suggestions?

    I recently moved into a new apartment and can connect with the internet by direct attachment to the cable/internet modem.  But when I try to connect the modem to my Airport Express, the Airport just blinks yellow and I cannot get my WiFi.  Any suggestions?

    Try this User Tip from forum expert Tesserax:
                     AirPort - Complete Power Recycle

  • Send the payment reminders (by emails) to the customers automatically

    Is it possible to send the payment reminders (by emails) to the customers automatically after the due date in SAP B1 2007 B PL7?... one of my client is asking it for a long time...

    Hi,
    Please take a look at this
    https://wiki.sdn.sap.com/wiki/display/ERPFI/DUNNING
    Thanks
    Bishal

  • Late 2012 Mac mini i7 to run dual Dell UltraSharp U2412M WITHOUT using the reported HDMI out problem port?

    I've been reading about all the problems new Mac Mini users are having with trying to expand their desktop using the HDMI port.  ie: snowy screens, fuzzy text, blackouts etc etc.  My Mini is due to arrive in a couple days and I have two Dell UltraSharp U2412M LED/ISP monitors waiting for it.  I know one of them will work fine with a cord I already have: miniDisplay to Displayport.  Is there any way to daisy chain them if I run into this HDMI problem the others are having?  THANKS.
    The monitors have:  Displayport, DVI, VGA connections only. 

    Mine shipped Oct 30 and I've had it running since Nov 6th. I took the original 4GB RAM out and replaced it with 16GB RAM. I also put a Mercury Elite 240GB SSD into the top bay using a doubler kit from OWC. I had an issue with the Disk Utility not liking the setup as two seperate drives. I ended up using Internet Recovery Disk Utility and did a Repair Disk on both drives and  Disk Utility merged the drives into a Fusion Drive which was then properly recognized by DU. It all seems to work well, although I would have preferred seperate drives and more partitions, Fusion Drives are only allowed 1 additional partition, go figure. The HDMI has a bit of overscan with my 50" Panasonic Viera but the colors are good and the picture and fonts clear and distinct @ 1080p. I frequently use 720p for larger images so I can sit on the couch 15' away and read the text without binoculars.

Maybe you are looking for