Firmware-upgrade failed router not accessible

during firmware-upgrade the connection to E4200 got lost due to power-outage, now the E4200 router is not accessible, power-led flashes ...
the factory-ip-address 192.168.1.1 responds on ping, but nothing else ...
how to get a working environment back?

Once reset the router. Steps to reset the router:
Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
Once the light gets stabilize on the router perform the following steps:
# Open up the browser and on the address bar type 192.168.1.1, it will prompt for the username and password. Provide the username as 'admin' and password as 'admin' or 'password'. Then it will open up the Router setup page.
# Then click on status and check the firmware version. If its not updated then upgrade the firmware once again.
# Then after firmware upgrade reset the router again as explained above.
Then uninstall the existing Cisco connect software from the computer. After uninstallation then configure the router again using Cisco Connect CD as you did earlier.

Similar Messages

Creative Zen Microphoto - "Firmware upgrade failed&qu

Hi,
two days ago my Zen Microphoto started in "Recovery Mode".
I had no means of getting out. I first selected "Clean Up" and rebooted, still "Recovery Mode".
Then I downloaded the latest firmware version for it:
ZENMicroPhoto_PCFW_L6__3_0.exe
Then I selected "Upgrade Firmware", acknowledged with "Yes", the firmware was deleted, but the windows firmware application said "no player connected" after connecting the player.
Okay, after googling a bit, I found out that I needed to downgrade from WMP to WMP 0.
I (painfully) did this and after installing an additional Registry Key via fixup.cmd the
ZENMicroPhoto_PCFW_L6__3_0.exe
detected the player (hurray!). It showed "Current Player Firmware Version .20.0 " and "Upgrade File Version .3.0".
When clicking on "Upgrade" at the windows application, the blue progress bar appeared and the player showed "Recovery Mode" and a blinking USB logo.
What it did NOT show afterwards was a gear symbol with "Upgrading firmware" (which I found on a screenshot in the internet).
When the blue progress bar of the windows firmware upgrade application reached about 85% it halted and after minute the windows firmware application showed "Firmware upgrade failed!" while the player only showed a black screen with "Recovery Mode" and the green battery symbol at the top.
I also tried the same procedure with
ZenMicroPhotoP4S_PCFW_LB__20_0.exe with the same result: "Firmware upgrade failed!"
Any ideas how to "repair" the player
Toddl
Message Edited by Toddl on 04-2-2008 09:40 AM

I have this same problem except with the Zen Vision: M. Any help would be appreciated.

Firmware upgrade fails

I am having trouble upgrading the firmware on my WRE54G. My hardware is v.3 and the existing firmware is 3.01.01.
I downloaded the latest firmware and extracted the .img file. I went to the admin page of the expander, pointed it towards the new firmware, and hit "go." After a minute or so it said something like:
Firmware upgrade fail.
Fail!
No reasons are given.
Anybody have any idea what is going on?
Thanks,
Garth

I had a similar problem upgrading firmware with my WRT300N. What i did to solve the problem was first i downloaded and went through the winzip program given for the router, then i went back to the webpage of the router and retried the upgrade and it worked. I actually ignored by routers version, and downloaded and went through each winzip program and each firmware upgrade for every different version . **i only downloaded the firmware up to my version and my version**.
Message Edited by DaveY on 11-15-2007 07:01 PM

Firmware upgrade failed, printer now say i has firmware version 0. attention light lights up

Hey all
I had a problem printing a pdf on my mac, and then tried to upgrade my mac driver and printer firmware.
But the firmware upgrade failed for some unknown reason. And now the printer just have the ready and attentions lights on constantly.
I have tried to restart and reset the printer many times, and tried the HP firmware upgrade utility several times, with no luck. It just say it was "failed to upgrade"
Any idea what to do ??
My printer is a HP Laserjet Pro CP1025nw
Thanks
Jan

Hello Jan
It definitely sounds like the firmware update failed. Firmware is like a devices Operating System. Without it, it can't do much. This is backed by the "failed" message and that your printer reports it has version 0.
The printer will need to be serviced. Please call HP Phone Support at 1-800-474-6836.
Don't forgot to say thanks by giving "Kudos" to those that help solve your problems.
When a solution is found please mark the post that solves your issue.

Vision:M - "Firmware upgrade failed!&qu

After spending several long, long hours rolling back WMP, trying different USB ports, installing and uninstalling various software, and borrowing friends' computers, I FINALLY got the firmware upgrade software to recognize my mp3 player. With great delight and an intense feeling of satisfaction, I clicked the "Upgrade" button and waited for several minutes, only to get a "Firmware upgrade failed!" message. I've tried the "Reload Firmware" option more than once, only to receive the very discouraging "Harddisk Problem". I've tried everything I can think of, from formatting to rebooting to resetting to reloading, but to no avail. I'm now left, like so many others, with a $300 bookend. Now what? I'm completely demoralized.

Well, being the stubborn person that I am,?I didn't listen to your advice andYesterday, against all odds from what I read on this forum, and being told that I would end up with an expensi've paperweight,? I decided to take the plunge and upgrade my Zen Vision M 30MB. ?I downloaded the newest firmware .6, saved it on my laptop which runs WMP 0, disabled all applications, including Norton and virus and spyware programs, as well as Creative's detector, connected my Zen Vision M to the USB dri've, double clicked the new firmware file, and followed the instructions. The new firmware started installing, within 3 minutes my player rebooted and then the library started rebuilding and within 5 minutes the process was SUCCESSFULLY COMPLETED!!!!!My player is working better than ever, it has all the new upgrades, album art, never went into Recovery Mode, and most important of all, I didn't lose any of my 2500 songs, hundreds of photos, slideshows and numerous videos, even my personal wallpaper and themes remained the same. I subsequently took the player to my desktop which runs WMP to test it'sand lo and behold, my player was immediately recognized, i transferred music and pictures without any problem and my player is now drag and drop compliant ?through Windows Explorer. My faith in Creative is unfaltering, I also own a MUVO TX FM, a Zen Micro and a Zen Sleek Photo and never had any problem with any of them.

WRK54G firmware upgrade fails: file pattern error.

When I attempt to upgrade the firmware in my WRK54G router, the upgrade fails with this error message:
Upgrade action is not finish!!
Upgrade file pattern error.
The linksys download page says the file size is 1.10 MB.
The size of the file I downloaded (WRK54Gv2_1_00_1) is also 1.10 MB (1,160,036 bytes). So it appears the file was downloaded successfully.
I had no problem upgrading the firmware to version 1.1.
Please advise.
Thank you

What is the hardware version of your router? Is it version 1, version 1.1 or version 2? Where did you download the firmware of your router? Is it from the US website.
On the US website you have 3 wrk54g, one is version 1, version 1.1 and v2.
"When love and skill work together, expect a masterpiece."

The firmware upgrade file is not supported on this hardware version MI424-WR Hardware Ver. C

Hello - I have been troubleshooting for quite some time a problem that only occurs on my wireless devices. 8 out of 10 times I fail to obtain a IP address from my MI424-WR. My connection to the device is successful, however, DHCP times out. I have connected to many other wireless routers in other locations in the last 4 weeks and have isolated my issue to my connection with my FIOS router. That is to say that when I am elsewhere I do not have this problem. I contacted support today, and the tech I spoke to was very nice and also clueless. What is the latest/current hardware ver of the MI424-WR Verizon is shipping? The tech said he could not tell me what ver the one he had in a lab was. If l log into the router under firmware upgrade I notice the message in my subject. I have had FIOS here with the same router since 9/2007. Any help would be apreciated.

That brings up something I have been curious about...could you see if this might work for you?
-First and foremost, log into the router
-At the top click Wireless Settings
-Go into basic security settings on the left and change the channel to 11 (yes, I know this doesn't work for all but please read on) and apply
-Now back on the left side menu choose advanced security settings, enter 802.11b/g Mode
---Honestly, most people should need G only by now, but choose what you need here (avoid mixed) and apply
-Go back onto the left menu and try advanced wireless settings again but this time choose "Other Advanced Wireless Options" at the bottom
-Change MTU to "manual" and enter in "1492" in the field it provides and apply
-Now at the top right go into advanced settings
-Click on the link for "System settings"
-In here UNCHECK the "Enable Logging" and "Low Capacity Notification" options and apply
I don't think they would be able to tell you which version is being shipped, because I am sure the new routers are coming with the new firmware and the old they send out first. But yeah, give that a shot and see if that does anything to help your wireless machines connect. I am kind of curious if that will change anything.

WRT350N- Firmware Upgrade Failed

when upgrading with .bin file (v1.05.8) via Administration - Firmware Upgrade, it fails when status showing 76% completion.
Please help what i need to do?
I already tried to boot in safe-mode to minimize programs running (firewall, etc), still showing Upgrade failed.
/v
Message Edited by viva on 10-20-2007 06:56 AM
(Edited subject to keep threads from stretching.
Thanks!)
Message Edited by JOHNDOE_06 on 10-20-2007 06:59 AM

Go to the control panel/network connections and right click on the local area connection. Click properties and roll down to highlight Internet protocol TCP/IP. Click the properties button and check "use the following IP address". Fill in 192.168.1.5 and tab through. The subnet mask will fill itself out to 255.255.255.0
make the preferred DNS server 192.168.1.1 (the router) and click okay.
If the computer succeeds in getting an IP address (verify this by opening a command window and typing "ipconfig" and seeing what it say under the local area connection), type ping 192.168.1.1 in the same command window and see if the router responds.
If so, you can use the TFTP.exe utility from linksys, available from linksysinfo.org at
http://www.linksysinfo.org/forums/downloads.php?do=file&id=4
Run this program, point it at the router IP 192.168.1.1 and show it the bin file you want to use. Might be a good time to use the released firmware rather than a beta. But that is your call. You can get the latest firmware from the linksys page.
If you are unable to ping the router, try putting the ethernet cable in a different port. Don't ask me why, but when my router bricked, it would only work on slot 4. Found this out by accident, but I was able to fix the router when I did this. If it does not work on any slot, you may be screwed. Call linksys and ask for a RMA to get a replacement. I would not tell them you bricked it with a beta firmware!

Tried to update WRT54G wireless router, upgrade failed, router broken.

I tried to upgrade my new WRT54G wireless router with the new firmware. I got an error message that said "Upgrade are failed". I used the correct version of the firmware for my router (I have a Ver 8). I tried to factory reset, but the router is still broken. Any suggestions on what I could do? The entire page I access via IP is broken. All the text is messed up the the links don't work. I can use the router to access my network, but it will not connect to the Internet at all.
Message Edited by Trax416 on 02-05-2008 01:05 PM

I have no firewalls, and it's for sure not a computer related problem. I have tried on three seperate computers. The upgrade failed, it won't let me access the setup page. I have tried to go onto the Internet since, and it lets me, but 80 percent of all Internet sites don't work. This is what shows up in the router firmware page when I go thru the IP. ýýý†††···ÇÇÇ¶¶¶¼¼¼öööiiiSSS¿¿¿ÂÂÂßßßààà´´´¯¯¯***^^^uuuAAAllØhhÐééé²²²äää–––ÃÃÃBBBâââmmm¾¾¾DDDWWW˜˜˜“““ìììÎÎÎ LLLaaajjÓyyy ¸¸¸ÝÝÝøøøÉÉÉãããÞÞÞ:::×××ÓÓÓkkk’’’nnn™™™³³³©©©ççç œœœxxx~~~ÁÁÁffÍ```ggÍ CCCiiÐ‘‘‘ ŠŠŠ@@@žžž YYYµµµÐÐÐªªª¥¥¥??9èèè___ÆÆÆ‰‰‰ÜÜÜšššÒÒÒ¨¨¨¡¡¡vvváááØØØÙÙÙƒƒƒTTT$$$ÍÍÍŒŒŒÚÚÚÔÔÔ••• ËËËÅÅÅëëëººº‚‚‚°°°|||}}}jjÕVVV„„„\\\]]]rrrbbÅ??;ŸŸŸ[[¶»»»[[[%%IGGG???eeË£££ííí‡‡‡fffooÝOO __¾kkÕGGŽ``Á88oddÇKK•CC†hhÏîîî±±±>>|SS¦77mÛÛÛæææpppÖÖÖ®®®ÈÈÈHH êêê??)ÌÌÌÊÊÊÄÄÄ????:llÙZZ²ŽŽŽWW®99q;;vAA‚ÿÿÿffÌ Message The rest of the pages in the setup menu ether show up blank, or give the same message as above.
Message Edited by Trax416 on 02-05-2008 01:35 PM

Spa508 firmware upgrade failed

I bought a spa500ds and need to upgrade the firmware on my 508G to use it.
When I try to upgrade to 7.5.4, or 7.5.3 I get a failure. I was able to upgrade to 7.5.1a fine. All firmware was downloaded from cisco this morning and unziped
I see my tftp server giving the file.
I get upgrade failed: 12. corrupt file in my syslog
Any idea where to look next?

It states on the release notes of 7.5.4, that upgrading from 7.5.1a you should first upgrade the phone to 7.5.2b.
Have you done this upgrade step?
Joao

WRT54GS V.4 Firmware upgrade failed.

Hi,
I need help on the unit on the firmware upgrade.
Info:
Device Model No.: WRT54GS v.4
Webpage firmware Version: v1.06.3
I had download the Version 4 firmware and upgrade fail.
Please help!!!!
Thanks

Are you getting any specific error..?
Which browser you are using...?
Are you upgrading the router's firmware from wireless computer...?
Use the hard-wired computer (connected to the router) and try to use Internet Explorer to upgrade the router's firmware and check.

Linksys e4200v2 firmware upgrade fails -bad file

I'm trying to upgrade my frmware to the lastest one (classic firmware)
I've downloaded this file multiple times http://homedownloads.cisco.com/downloads/firmware/1224693043651/FW_E4200_2.0.37.131047.zip
When I try the firmware upgrade (manual upgrade) and select the file, it always complains about the file being corrupt (using the .ssa file in the zip).
How can I solve this issue?
Kind Regards, Jurgen

Hi, I’ve noticed that all smart routers’ classic firmware starting from E4200 v2 to EA4500 contains .ssa as the file extension. So, the moment you load a firmware with that file extension then the router should automatically read it. What you can do is to use other browsers or better yet use another computer just to isolate the problem. If that will not work then try the following:
Download the tftp utility (select version 4)
Disconnect the modem from the router and just have the computer connected to the router's ethernet port
Assign a static ip address on your computer
Lower the speed of the computer's LAN card to 10 half duplex
disable any firewall or anti-virus software on your computer
Run the tftp utiilty

E1200 Firmware Installation Failed, Router Unresponsive

I had a message in Cisco Network Magic that a firmware upgrade was available. I clicked the link and the download and installation process started. My computer is hard-wired to the router. After a time, it said it was finished, but I could not get Internet access. Nor could I log into the router from my computer. The Internet connection was working when I connected directly to it with my computer. I then did a hard reset of the router and attempted to reinstall it from factory settings using Cisco Connect. Still no luck. The lights are blinking on the back of the router, but I can't seem to reinstall it.

What is the model number of your router? The update prompt from Network Magic, was it for your router? Anyway, since you tried the reset already and Cisco Connect does not seem to work, try to check if you can ping the router. If you can, try to access its setup page and reconfigure it from there. You may want to try reset again and download and install the updated Cisco Connect from Cisco's website. Should that will not work also, then do the manual reconfiguration and you refer to these links that will help you with that: Setting up your Linksys wireless-N router without using the setup CD; Setting up a Linksys router for DSL Internet connection; Setting up a Linksys router with Cable Internet service

SGE2010P 48port Gigabit POE Firmware Upgrade fails

I have a Linksys SGE2010P 48 Port switch with POE and I cannot get the firmware to upgrade.
I have downloaded the firmware software from the site: http://www.cisco.com/en/US/products/ps9985/index.html
Everytime I run the EasyUpgrade application I get the error after it starts the Telnet session:
"Did not find device information. Application will terminate"
I cannot find any reason why this is happening. I know that I have a SGE2010P and I know that I am downloading the correct firmware.
Am I missing something?

I am having the same issue where the "Easy upgrade" utility fails. When I try to upgrade firmware via the Web GUI, I am able to upload the "Software Image" & when I click "Done" the Firmware Upgrade screen displays again without any status and/or notifications relating to the firmware that was just "successfully" uploaded (according to the screen at least).
I was able to successfully upgrade the Boot Version from : 2.0.0.00 to 2.0.0.03 with this same process so what is going on with the Firmware update?
It is as if the Firmware is uploading to the switch but the update is not running.
Help!

WRT54GS Firmware Upgrade Failed

I'm trying to upgrade the firmware on my v2 WRT54GS - (serial number starts CGN30E4...)
I've downloaded the appropriate firmware from the website (http://downloads.linksysbycisco.com/downloads/WRT54GSv3_4.71.4.001_fw,2.bin) and then tried to apply it. Every time I have tried to apply it the progress bar starts moving, and then after a minute or so I get redirected to a screen that says "Upgrade Are Failed".
Have I done something wrong here?
Thanks in advance,
Scott

Well you can try to Upgrade the firmware of the Router in a different way please follow these Steps:
Please click here and download the setup wizard and save it on the desktop and then double left click to run it.
When you run the downloaded setup wizard it will as you for Server, Password and file.
In Server type the Default gate way of the Router i.e 192.168.1.1.
In Password type admin the default router password.
In file browse the firmware file which you have downloaded.
Try to upgrade the firmware this way.

Firmware-upgrade failed router not accessible

Similar Messages

Maybe you are looking for