Freeview Plus doesn't work on my KDL60W850B.
Freeview Plus doesn't work on my KDL60W850B.I purchased the tv June 2014. The Sony site says 'Freeview Plus compatibility (in Australia only)'. I have pressed the green button and nothing happens.Firmware has been updated.
Hi lukebrewer1,
Welcome to the Sony Community!
Please perform Refresh Internet Content. Here are the steps:
Press the Home button.
Select Settings.
Select Network.
Select Refresh Internet Content and press the button.
For further assistance regarding your concern, please contact the Sony offices/Sony representative offices nearest to your place of residence in Asia Pacific region http://www.sony-asia.com/countryselector.html?hpid=countryselector:AsiaPacific. Due to proximity, they are in a better position to respond to your questions or concerns.
If my post answers your question, please mark it as "Accept as Solution"
Similar Messages
-
BRF plus doesn't work on Conditions and calculations
Hello,
When you create an additional filter or condition on the business rule, it doesn't work on the ad hoc query. What is wrong with it?You should save your conditions, close the window, open it again and it should work properly.
-
My creative zen nano plus doesn't work anym
Hi I've a problem with my mp3 player. It just doesn't work. After I made a powerpoint file on it (normaly that did not cast problems) it went on and in the same time it wents off. Like the battery is not loaded. I wanted to make an update with a file from the creative page, but in the same time it did not do anything. I can not turn it on. It does nothing.
Can somebody help me? Had anyone the same experience?
My problem is too, that its nearly two years old and the seller told me that i have no guaranty on it. Is this right? Can i just turn it into the carbage can?
Please help mejumpshot22 wrote:
"I found out the hard way that for it to be able to charge by USB on a computer, the software has to be installed which I think is pretty retarded. You should definitely pick up a charger cause it's a lot faster to charge and more convenient. " -- some guy who reviewed the mp3 player
i cant find where this other guy who said like the same thing
They must have been talking about a different player such as the Zen Micro which does recharge via the USB port.
PB -
Dervish(plus) doesn't work with new ios7.
I have tried contacting Dervish and Whirling Disks Ltd but without success. Where do I stand please? I presume it's still on sale?
It's still in the app store so yes, it's still on sale. There is no info on the page re iOS 7 support, it just says "Requires iOS 4 or later". It's still a 1.0 version that hasn't been updated since it was released in Mar 2012, that's usually not a good sign unfortunately. I presume the band paid a contract developer to write the app in the first place and would now need to pay again to have it updated to support iOS7.
I guess if enough fans pester them they'll figure it's worth the money, if not they probably won't. Given that there are no ratings for the app at all that may indicate that they didn't sell many copies of it and so the odds of enough fans requesting an iOS 7 compatible version are not good.
In short you have no option except to wait and hope they update the app for iOS 7 one day. -
my iphone 6 plus after updating to IOS 8.2 seems to have a problem with the touch id witch doesn't work neither in home unlock nor in app store and when i'm trying to add a new fingerprint it says ''failed unable to complete touch id setup.Please go back and try again'' . I have multiple fingerprints and none of them appear to work.
Hi Giannis,
If you are having an issue with Touch ID not functioning as expected, I would suggest that you troubleshoot using the steps in this article -
Use Touch ID on iPhone and iPad - Apple Support
Start with the section titled Clean the Touch ID sensor and then Get help with Touch ID.
Thanks for using Apple Support Communities.
Sincerely,
Brett L -
Backup Assistant Plus simply doesn't work, how do I disable it?
I have a shiny new Samsung Galaxy S III and when I set up my contacts, I added them as "Phone" entries with the expectation that the Backup Assistant Plus app would allow me to back them up. Except that it doesn't and, from what I've seen online, it is a miserable piece of junk that simply doesn't work for many people.
Soooo....
I sent all my contacts as a big V-card to my Gmail account, sorted things out in Gmail, unjoined them all on the phone, and deleted the Phone entries. Now I only have Gmail contact entries and they synch with no issues.
My only question now is, how do I disable/stop Backup Assistant Plus so that it doesn't constantly give me notifications about how incapable it is? I've tried clearing it's data and forcing it to stop. But it comes back from the dead, like a demonic zombie! It appears the only thing the app can do is resurrect it itself for the sole purpose of notifying me that it will fail to do anything useful.
Any and all help with this issue is greatly appreciated.greblaws wrote:
I have been trying to disable Backup Assistant Plus since it is a BATTERY and PERFORMANCE HOG! I have a lowly Droid3, and it has been really causing issues.
Your instructions above DO NOT WORK, under Manage Applications I get "Uninstall updates" - I cannot uninstall it. It is a "system application" and I am locked out of that control. GRRRR. Clear data does not do anything for performance.
Even when on wifi, this app's backup of data is slower than TAR in January. Biggest issue is the
The reason the steps to uninstall the app didn't work is because the DROID 3 is running Gingerbread (Android 2.3). The instructions above were for the Samsung Galaxy S III running either ICS (Android 4.0) or Jelly Bean (Android 4.1).
You can however "Clear the Data" for the app and from that point never use the app. The phone will learn to not load it into the RAM in case you ever use it. -
Can you help as FaceTime no longer works which is really frustrating plus an app doesn't work like it dies on a friends old iOS
Hi, Sezzy31.
Thank you for visiting Apple Support Communities.
I would need clarification of your issue to provide a better answer. However, if you are experiencing issues with FaceTime, here are some troubleshooting steps that I would recommend going through.
iOS: Troubleshooting FaceTime
http://support.apple.com/kb/ts3367
Cheers,
Jason H. -
Dock Plus Series 3, Mic doesn`t work
As I use Skype a lot, I bought Dock Plus Series 3 to solve the issue with mic jack at Lenovo`s stupid engeneeres "designed" for t420s model. No one profesional pmanufacture produces mic for this kind of jack, and it is always Pain in the Ass to connect external mic to the machine.
Dock Plus Series 3 has normal, industry standard mic jack. I hope it will soleve the issue. But it is not! No one mic doesn`t work if i plug it Dock Plus Series 3. Please advice, how to make it works!
PLEEEEEEEEEEEEASE !Hey Baramburum,
I could not find any drivers for your docking station, what I can suggest is that you update your audio drives from the link below and you update your BIOS. If you do the update please remove the old drivers first completely and then install the new ones.
Audio driver: http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS014918
BIOS: http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS014992
Best Regards,
Hiro
Did you find a post Awesome? A response just Outstanding? Kudo them!
Did the post you read answer your question? Did someone help you figure out your problem? Hit Solution Provided and give that person a pat on the back for helping you out! -
*228 doesn't work on iPhone 6 plus. How do I update roaming?
*228 doesn't work on iPhone 6 plus. How do I update roaming?
You don't update using *228 on devices with Sim cards on Verizon. IIRC it'll update automatically or after a restart.
-
Youtube doesn't work on my iPhone 6 plus,any help ?
youtube doesn't work on my I phone 6 plus ? any help ?
Would you please provide a little bit more info about your issues with YouTube? What doesn't work? YouTube in Safari? YouTube in Chrome for iOS? The YouTube app? What happens when you enter youtube.com or open the app? ...
-
# Question
How do I disable those pesky "hover-over" pop ups? I tried the method of right clicking on them and opting out, but it doesn't work. If you guys could add some kind of blocker to your browser, it would be a huge plus!Chris CA wrote:
Did you createa smart playlist? It's purple with a gear icon.
And you set the criteria to
Match rule:
Date added is in the last two weeks?
I tried it, but couldn't get it to work. I think I had trouble with the Rule. I put a Rule in as follows: Data added in the last five hours? I added music (data) but nothing appeared in my Smart Playlist. Oh yes - I named the playlist: Recently Added.
What did I do wrong? Is it necessary to have a question mark at the end of the Rule? I couldn't find anything on how to create a Smart Playlist in Help. There is stuff in there, but it does not go into much detail, i.e., nothing on the proper wording of the Rule. -
The + sign to add a new tab suddenly stopped working a while ago. I tried uninstalling and re-installing and it still doesn't work. What may have happened and how do I fix it?
Hello,
The Reset Firefox feature can fix many issues by restoring Firefox to its factory default state while saving your essential information.
Note: ''This will cause you to lose any Extensions, Open websites, and some Preferences.''
To Reset Firefox do the following:
#Go to Firefox > Help > Troubleshooting Information.
#Click the "Reset Firefox" button.
#Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
#Firefox will open with all factory defaults applied.
Further information can be found in the [[Reset Firefox – easily fix most problems]] article.
Did this fix your problems? Please report back to us!
Thank you. -
Interleaving doesn't work properly for Cisco 3725 router, IP Plus IOS
Dear All,
I am deploying VoIP between 2 sites using Cisco 3725 routers. Currently, interleaving doesn't work properly which result in voice quality problem only during data trafic. Issuing "show int multilink 1" command, I realise that there is no interleaves even though VoIP call and data are traversing on the link.
Attached here is the info for your reference.
Any idea, please help.
Thanks in advance.
DucHere is the info:
VNHCMR01#sh call active voice brief
: hs. + pid:
dur hh:mm:ss tx:/ rx:/
IP : rtt:ms pl:/ms lost://
delay://ms
MODEMPASS buf:/ loss /
last s dur:/s
FR [int dlci cid] vad: dtmf: seq:
(payload size)
ATM [int vpi/vci cid] vad: dtmf: seq:
(payload size)
Tele : tx://ms noise: acom: i/o:/ dBm
MODEMRELAY info:// xid:/ total://
speeds(bps): local / remote /
Proxy :,,,,, endpt: /
bw: / codec: /
tx: /,/,/
rx: /,/,/
Telephony call-legs: 1
SIP call-legs: 0
H323 call-legs: 1
MGCP call-legs: 0
Total call-legs: 2
12FF : 5798794hs.1 +202 pid:80 Answer 710 active
dur 00:01:14 tx:3721/74420 rx:3721/74420
Tele 0/0:15:424: tx:74420/74420/0ms g729r8 noise:0 acom:24 i/0:-50/-29 dBm
12FF : 5798794hs.2 +202 pid:81 Originate 81555 active
dur 00:01:14 tx:3721/74420 rx:3721/74420
IP 159.12.56.1:19526 rtt:30ms pl:73890/40ms lost:0/1/6 delay:67/67/107ms g729r8
Telephony call-legs: 1
SIP call-legs: 0
H323 call-legs: 1
MGCP call-legs: 0
Total call-legs: 2
VNHCMR01#sh int mu1
Multilink1 is up, line protocol is up
Hardware is multilink group interface
Description:
Interface is unnumbered. Using address of FastEthernet0/0 (159.12.55.2)
Backup interface Dialer1, failure delay 30 sec, secondary disable delay 30 sec,
kickin load not set, kickout load not set
MTU 1500 bytes, BW 256 Kbit, DLY 100000 usec,
reliability 255/255, txload 33/255, rxload 13/255
Encapsulation PPP, LCP Open, multilink Open
Open: CDPCP, IPCP, loopback not set
DTR is pulsed for 2 seconds on reset
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters 00:00:50
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0/0 (size/max total/threshold/drops/interleaves)
Conversations 0/5/64 (active/max active/max total)
Reserved Conversations 1/1 (allocated/max allocated)
Available Bandwidth 56 kilobits/sec
5 minute input rate 14000 bits/sec, 69 packets/sec
5 minute output rate 34000 bits/sec, 72 packets/sec
3062 packets input, 100509 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
3078 packets output, 298192 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
VNHCMR01#sh ppp multilink
Multilink2, bundle name is VNHANR01
Bundle up for 02:47:34, 3/255 load
Receive buffer limit 12192 bytes, frag timeout 1000 ms
0/0 fragments/bytes in reassembly list
0 lost fragments, 0 reordered
0/0 discarded fragments/bytes, 0 lost received
0x145A1 received sequence, 0x21A41 sent sequence
Member links: 1 active, 0 inactive (max not set, min not set)
Se0/2, since 02:47:32, 320 weight, 312 frag size
Multilink1, bundle name is VNBHCR01
Bundle up for 16:07:32, 35/255 load
Receive buffer limit 12192 bytes, frag timeout 1000 ms
0/0 fragments/bytes in reassembly list
0 lost fragments, 0 reordered
0/0 discarded fragments/bytes, 0 lost received
0x2DB8D received sequence, 0x536BD sent sequence
Member links: 1 active, 0 inactive (max not set, min not set)
Se0/1, since 16:07:30, 320 weight, 312 frag size
VNHCMR01#sh run int multilink 1
Building configuration...
Current configuration : 380 bytes
interface Multilink1
description
bandwidth 256
ip unnumbered FastEthernet0/0
service-policy output llq
backup delay 30 30
backup interface Dialer1
ip tcp header-compression iphc-format
no ip mroute-cache
ppp multilink
ppp multilink fragment delay 10
ppp multilink interleave
ppp multilink group 1
ip rtp header-compression iphc-format
end
VNHCMR01#show policy-map
Policy Map llq
Class voip-rtp
Strict Priority
Bandwidth 50 (%)
Class voip-sig
Bandwidth 8 (kbps) Max Threshold 64 (packets)
VNHCMR01#show class-map
Class Map match-any class-default (id 0)
Match any
Class Map match-any voip-sig (id 1)
Match access-group name VoIP-SIG
Class Map match-any voip-rtp (id 2)
Match ip rtp 16384 16383
VNHCMR01# -
Own an iphone 5. Can't control voice memo volume from anywhere that deals with volume on my phone. My decrease button doesn't work. I have to listen to my voice memos on full blown volume. Can't lower it from settings or from music. Help please!
Hi,
thanks for your answer.
The Size of all disks is: 6 x 4 TB.
In the Pool are 5 x 4 TB plus 1 x Hot Spare.
It comes up to about 14,6 TB of Data formatable.
But tried it also with just 3 x 4 TB to see if it works.
I just made a Raid5EE on the controller and then used Storage Spaces with simple, all worked fine.
Here the results of my tests:
1) your command had to be modified (typoe in usemaximumsize, and had to add -ResiliencySettingName Parity.
new-virtualdisk -friendlyname testpsh -storagepoolfriendlyname test -ResiliencySettingName Parity -usemaximumsize
But anyway, my problem is not creating the virtual disk, but formatting the partition if it's parity only.
I added a screenshot:
Here you see my storage pool, and I added 3 virtual disk.
1 simple, 1 mirror, 1 parity. Only the parity cannot be formatted. The others can. No mather which size I do.
About a testserver, I added 4 x 4 TB to a VM (VHDX-files) and could do parity without problems. So it seems it is this server specific.
As it worked with another controller, I really wonder if the controller could break parity of Storage Pools?
The other weird part is, it sais "Raid" as BUS, but it's set to pass through, in details I see the serial of the attached HDD.
This is what properties shows on this volume. Always RAW.
I also tried Software Raid5 within the server.
This also worked fine. So really only parity.
Thanks
Patrick -
Skydrive built in app wont let me update it and it doesn't work
A day after the name change became official my built in skydrive app stopped working. Every time I click on the app it loads the clouds then goes to a message "This location can't be found, please try again later", then it flat crashes and I
am back at the start screen. What the hell people, why? Also, why the hell can't I uninstall it then just re-install it? What on earth possessed you into believing that this app HAS TO BE BUILT IN, for god's sake Microsoft the damn thing is broken now and
the only possible way I can think of to fix it would be to refresh the OS which I don't want to do because then I have to sit around and let it update all over again plus I would have to re-install my programs as well. I hope you not only fire the engineer
who thought this was a good idea but I also hope you castrate him. This was truly a sad, unnecessary, stupid act to do. All you idiots had to do was make this no different from office 365 and I would have uninstalled it, re-installed it and probably saved
us all the trouble. Also, it hasn't stopped me from using onedrive but the entire point of your built in app has become pointless, it doesn't work because of your name change for some reason and now I can't fix it without sacrificing a whole damn day to get
back to where I am at. Would it be too much for you to make this onedrive app removable in your next firmware update? As of now, I have removed your office 365 because that was a pointless thing to have when I already have office 2007 but now I am stuck with
this broken skydrive app that I can't fix, update, or remove without sacrificing my time. It is not easy re-installing a program like bluebeam revu you know and as of yesterday my photos app has now become just like the skydrive app, it doesn't work, my pictures
are all there but the app itself keeps crashing. Seriously man, let us remove your trashy apps and let me re-install it alreadyHi,
"A day after the name change became official my built in skydrive app stopped working"
Did you point that SkyDrive changed to OneDrive?
Did you move your OneDrive to another location or change its name?
Please login OneDrive with web-based to check if you could access it successfully.
Please refer to the following article to try the troubleshooter and check the service status:
SkyDrive: FAQ
http://windows.microsoft.com/en-in/windows-8/skydrive-app-faq
Karen Hu
TechNet Community Support
Maybe you are looking for
-
I have one HDMI port on my television that is currently used for my hard drive/free view box. What kind of adaptor can I buy so I can have the hard drive and my apple tv device plugged into the same HDMI PORT? Is it a switch or a splitter? And wher
-
Problems importing files or folders into my itunes library
When I try to import files, mp3, wav etc, from my hard drive into my itunes library they seem to be automatically being deleted from my hard drive. I can play them in windows media player but they disappear into the ether if I want them on my Ipod. A
-
How to see all Expired Quotations in the System?
Dear all, How can we see all expired quotations in the system. Thank you
-
Can a gift purchase be refunded if the recipient already bought the album?
I gave an album as a gift right after my son had already purchased it. Can he (or I ) get a refund? I had no idea he had just bought the same album, literally minutes before I had sent it to him as a gift.
-
Beats audio "cannot find .startup file"
HP Pavillion Notebook dv6 windows 7 home premium I have tried the windows recovery step without any luck and downloading the drivers and beats software with the same results. there is no sound coming out from my speakers either, when i try to test to