FTP to AS/400 from J2SE Adapter

Hi,
I setup a J2SE adapter that with push the XML through XSLT to produce a flat file that in turn is to be FTPed to an AS/400 machine.
This is an extract of my adapter config:
<i>##File Adapter specific parameters
file.createDir=0
file.targetDir=/FTPBARSA
file.targetFilename=WARHEADTST
file.writeMode=append</i>
This works 100% to my IIS FTP, however, to the AS/400 I get the following error:
ERROR: Message processing failed with "java.lang.Exception: com.sap.aii.messaging.adapter.ftp.FTPEx: Unknown extension in database file name."
If I use the .SAVF after the target filename, I get the following error code:
ERROR: Message processing failed with "java.lang.Exception: com.sap.aii.messaging.adapter.ftp.FTPEx: Unable to close file.  Error code CPE3101. Data transfer ended."
I am able to put the file using DOS FTP without a problem.
Any idea how I can do the transfer to the AS/400?
Rgs,
Johan Schoeman

Although inactive wondering if solution was ever found to this I/O error and if so what?
Thank you.

Similar Messages

  • HTTP/S POST from J2SE adapter engine (NO SOAP)

    Hi there,
    We have a scenario at work where we have XI sending messages to the "lightweight" J2SE adapter engine in the DMZ....and from there the message is sent out to an HTTPS site that is obvioulsy outside of our network.
    Currently I can see that the J2SE adapter engine support SOAP over HTTP/S......but how can I do a normal POST of the message NOT using SOAP to an external HTTP/S address?
    I do not see any straight HTTP adapter in the J2SE adapter engine. I have a small java file that can connect and POST the message to the external website.
    My question is how can I use this code easily in the J2SE adapter engine? I just want a simple HTTP
    POST ...no SOAP.....
    Is there some sort of EXIT or dispatcher that I can hook onto?
    Any help or push in the right direction will be greatly appreciated
    Regards
    Lynton

    Hi there,
    You can see in the config file below that we did put it into the adapter config. It does not complain about the parameter BUT it still has the SOAP envelope / headers in the result message. Any ideas how we can get around this?
    Thanks for the help
    Lynton
    # Bubble adapter java class
    classname=com.sap.aii.messaging.adapter.ModuleBubble
    # Sets the bubble module helper that can instantiate your bubble bag
    Bubble.Helper=com.sap.aii.messaging.adapter.ModuleBubbleHelperXMBWSImpl
    #$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
    # Below this line are the parameters specific to the ModuleBubbleHelperXMBWSImpl
    #$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
    # The configuration of this helper class is divided in three parts. The first part,
    # Part 0, specifies the common parameters. The second part, Part 1, specifies the
    # adapter configuraton for Web-Service clients communicating with an XMB server.
    # The third part, Part 2, specifies the configuration for XMB clients
    # communicating with a WebService server. For sender or inbound adapters, Part 0
    # and Part 1 must be configured. For receiver or outbound adapters, Part 0 and
    # Part 2 must be configured.
    # This is a sample configuration file for a SOAP Outbound/Receiver Adapter
    ###### Part 0 (FromWS and ToWS) : common part ######
    # Keeps the XMB headers in web service messages
    XMBWS.KeepHeaders=false
    # Keeps the attachments in web service messages
    XMBWS.KeepAttachments=false
    # Encodes the xmb headers into a special HTTP header string x-xmb_ws_encoded
    XMBWS.UseEncoded=false
    # Encodes the value of x-xmb_ws_encoded (see UseEncoded) in the request query string
    XMBWS.UseQueryString=false
    # Uses the specified xml encoding for the soap envelope encoding
    #XMBWS.XMLEncoding=iso-8859-1
    *XMBWS.NOSOAP=true*
    ###### Part 1 (FromWS) : WS clients to XMB server ######
    # This part is configured for SOAP Sender or SOAP Inbound-Adapter)
    # It is left empty in this configuraton file.
    ###### Part 2 (ToWS): XMB clients to WS server ######
    # This part is configured for SOAP Receiver or SOAP Outbound-Adapter.
    # The target URL for the web service, to which the adapter sends web service messages.
    XMBWS.TargetURL=https://localhost:443
    # The port and path where the adapter waits for XMB messages from clients.
    XMBWS.XMBPort=8015
    XMBWS.XMBPath=/bt
    XMBWS.SSLcertificate=somecert.p12
    XMBWS.SSLcertificatePassword=hello
    XMBWS.SSLauthentication=true
    # The default SOAPAction HTTP request header to the web Service server
    XMBWS.DefaultSOAPAction=xmbws
    # END

  • J2SE adapter upgrade to PI 7.1

    Hi,
    is there anything special that needs to be changed
    when moving those local (J2SE) adpaters from 7.0 to 7.1 ?
    anyone already moved those pretty, little, file configuration based devils ?
    Thank you,
    Regards,
    Michal Krawczyk
    http://mypigenie.com XI/PI FAQ

    Hi Michal,
    Unfortunately I dont have a PI 7.1 server to test.
    Michal are you facing any issue when working J2SE Adapters with PI 7.1?
    @Rajesh:
    >I read some of the documents that J2SE adapters aresupported only in XI 3.0 to support XI 2.0 implementation customers
    Though the document says it works for XI 3.0, it still works with PI 7.0 since the concept lies in posting the message to XI PIPELINE while sending from J2SE Adapter
    and on the way back from XI to J2SE Adapter Engine using one of the configured working servlet in J2SE Adapter Engine.
    Thanks,
    - Gujjeti.

  • I am using IMovie 11 with a new iMac.  Unable to import video from a Panasonic PV-GS400 mini-DV camcorder using a Firewire IEEE 1394 400 cable connected to a Firewire 400 to 800 adapter which is then connected to a Thunderbolt to Firewire 800 adapter.

    How can I get iMovie to recognize my Panasonic PV-GS400 as a device so I can import video to my iMac?  I have a FireWire IEEE 1394 400 cable connected to the camcorder.  Since my new iMac has only Thunderbolt ports, I purchased a Firewire 400 to 800 adapter to connect to the cable.  I also purchased a FireWire 800 to Thunderbolt adapter to connect to the computer.  My camcarder is still not recognized.

    I would suggest that you try a 9 pin to 4 pin Firewire Cable along with the Firewire to Thunderbolt adapter.
    Those Firewire 400 to 800 adapters do not seem to work well with iMovie.
    The 9 pin to 4 pin cables are available at reasonable prices here, for example.
    http://www.monoprice.com/products/product.asp?c_id=103&cp_id=10301&cs_id=1030104 &p_id=3541&seq=1&format=2

  • Filename in J2SE Adapter with Variable Substitution

    Hello,
    Within the J2EE receiver fileadapter (and ftp) from SP13 it is possible to compose the target filename and directory based on the payload of a message using variable substitution.
    I wonder if it is also possible to use variable substitution with the J2SE fileadapter. For this it is not documented but i thougth that the same java libraries are used for the J2EE an J2SE file-adapters.
    Aybody??
    Really Nobody??
    Message was edited by: Emile Hermans

    Hello,
    the J2SE Adapter does not support variable subsition. Therefore we created our own class which gets called from the main SAP XI class "XMB2FileProcessor.class" wich is in the jar "aii_msg_adapter.jar". In your own class you can do what ever you need to chane the file name. In the configuration you can set your own parameter to search the payload for a string you want to replace. We also had to come up with our own timestamp, e.g. file2005-11-10 which SAP does not let you do, only the full timestamp is possible.
    One other nice thing is that you can develop our JAVA class local and test it with your local J2SE Adapter Engine on you PC before you deploy it.
    Steps to do:
    1. JAD the SAP class
    2. Put a call in the SAP class
    3. Compile the class
    4. Put the class back in the archive
    5. Create your own class
    6. Create a jar file for it
    7. Put the jar file in the tech_adapter directory
    8. Change the run_adapter start cmd to include your jar file
    It works great, the only issue is if you patch the J2SE engine you have to do step 1 to 4 again but that should it very easy to do.
    Cheers
    Stefan

  • J2SE Adapter Registration

    I've tried to get an answer for this question long time ago, but no one ever answered.
    How to register J2SE adapter with XI ?
    I tried using SLDAccess service on J2SE adapter with no luck (with this J2SE Adapter Engine is registered in the SLD). My J2SE adapter was never available in the configuration means, in the communication channel ex: file adapter, for the adapter engine drop down all I have is Integration Server, my J2SE adapter was never listed there.
    thanks
    SKM

    Tony,
    You do not need FTP server to use file adapter. I've installed and configured a J2SE Adapter Engine on my laptop.
    I was able to use sender adapter but not the receiver adapter. I've followed all kinds of documentation, asked Qs in the forum but never got any feed back.
    After you install plain J2SE AE on your laptop, you have to configure SLDAccess service. Once it is connected to SLD, you can see the adapter engine name in the XI technical systems.
    Then you can configure FileAdapters by copying the existing one. Go through the Adapter documention in the installed directory.
    Hope this helps.
    Regards
    SKM

  • How to go for Advance selction for source file in J2SE adapter

    Hi all,
               I am doing a file to file scenario using J2SE adapter.I have to pick file from two different directory  we  can easily achieve it in J2EE adapter using advance selection of source file but how to proceed in case of J2SE plain adapter.Please guide me with your knowledge.
    Regards,
    saurabh

    This is not possible. You need different adapters, but you can use the same interface and namespace, so there should be no issue.
    Regards
    Stefan

  • "Performance" problems with the File adapter on Plain J2SE Adapter Engine

    Hi,
    At the moment I'm on a customer side to solve some XI issues for a few days. One of the issues is the performance of the Plain J2SE Adapter Engine, using the file adapter to transfer XML messages(already XI message format) from the legacy system to the Integration Engine. The File adapter has to deal with "large" XML messages(max at the moment is 65 Mb) and the engine fails with the following error when transferring the big XML file: "ERROR: Finished sending to Integration Engine with error "java.lang.OutOfMemoryError". Skip confirmation and quit this loop".
    As far I got the information from the customer the memory use of the Plain adapter engine is set to 512Mb. This is maybe to low. But I don't know where to look for this, I only have the adapter web interface in front of me, no access to the OS it self via for example remote connection.
    On the Integration Engine I know there is the ability to split large message with the file adapter(File Content Conversion), but I don't know this for the Plain Adapter Engine. Is there a possibility to do this also on the Plain Adapter Engine?
    Thanks in advance for any input.
    Greetings,
    Patrick

    Hi Sameer,
    Thanks for your answers.
    On the first solution, yes that is possible, we first decided to see if the legacy system can do the splitting, before starting developing a Java program.
    On the second solution, as far as I know is this solution possible on the Integration Engine. But we are facing the problems on the Plain J2SE Adapter Engine. I went trough that documentation(link:
    http://help.sap.com/saphelp_nw04/helpdata/en/6f/246b3de666930fe10000000a114084/frameset.htm ), to look for I similiar solution in the Plain Adapter Engine. So my question is, is this possible with the Plain Adapter? And if so, what kind of parameters I need to use to achieve this.
    Regards,
    Patrick

  • Installation and then Configuration of Plain J2se Adapter Engine

    Hi All,
    Actually we want to use JMS Adapter for that we had installed Plain J2SE Adapter Engine but after installing and following the initial steps of Adapter.pdf we are not able to access the Adapter Engine through URL.We are using the URL http://<hostname>:8200/MessagingSystem/receive/AFW/XI
    this URL is there in our SLD but we are not able to access the page.
    So Please can somebody help me to resolve this issue.
    Thanks & Regards
    Sathya

    Hi Amol,
    I am trying to send read data from MQSeries using JMS adapter. We are successful in opening the Adapter Engine  and the GUI. We have cofigured the adpter as follows. But when we try to restart the adapter to get the changes get saved we are getting the following error
    <b>"ERROR CALLING THE RESTART ADAPTER"</b>
    Also status is shown is yellow and version is shown as not set.
    Where ever I have changed the configuration data I have shown it in bold
    JMS-Adapter Configurarion
    This Configuration is a sample for a JMS sender channel (inbound, sends to XI IS)
    Set XI message protocol version. This sample is designed for XI 3.0
    version=30
    JMS message receiver class
    classname=com.sap.aii.messaging.adapter.ModuleJMS2Transport
    set if a transacted JMS Session should be used (default: true)
    #JMSSession.sessionTransacted=false
    set delay in milliseconds before processing next message after an error (default: 0)
    errorDelay=10000
    #set delay in milliseconds before trying to reestablish the JMS Connection after a connection error (default: -1 (do not try to reconnect))
    #reconnectDelay=10000
    set the Message Formats you want to process (Formats only needed if they can not be evaluated at runtime)
    TransportMessage Type can be set to TransportMessage of XMBMessage. It is used for sending and receiving Transport and XMBMessages
    #TransportMessage.type=TransportMessage
    TransportMessage.type=XMBMessage
    uncomment and adjust parameters for Transformation Type (Binding of JMS-Transport Message),
    insert your class here for an individual binding between JMS and Transport Message
    uncomment the following line for using Bindings that belong to Tunneling
    #transformClass=com.sap.aii.messaging.adapter.trans.JMSTunneling
    uncomment the following line for using Bindings that belong to Single Payload Binding
    transformClass=com.sap.aii.messaging.adapter.trans.JMSSinglePayloadBinding
    ID Garbage Collector: For EO(IO) handling XI adapters store the JMS/XI message ID's in the ID logger
    Uncomment the following lines and change the default values if you recognized "out of memory" problems due to
    very large ..\tech_adapter\Data\*_ID.dat files which will be kept in the memory as well
    eoExpirationAfterDays is the period of keeping the message ID in days. Afterwards the message ID might be used again
    garbageCollectorInterval is the period in milliseconds when the ID garbage collector is started. It will however only
    be started if messages are exchanged otherwise ID logs won't be created anyway
    eoExpirationAfterDays=365
    garbageCollectorInterval=86400000
    <b>#
    the following parameters are used in some Bindings that belong to Single Payload Binding needing XMBHeader Information
    uncomment and adjust parameters according your requirements. Please note, that the party identfier needs not to be
    configured in case of A2A scenarios.
    #XI.SenderParty=Sender
    XI.SenderService=MQSeries
    #XI.ReceiverParty=Receiver
    XI.ReceiverService=MTX
    XI.InterfaceNamespace=http://xitest
    XI.Interface=MI_Out_File
    XI.TraceLevel=1
    XI.LoggingLevel=1
    XI.QualityOfService=EO
    XI.QueueId=ABCD
    XI.ContentType=text/xml
    #</b> *************************************************************************************************************
    <b>#
    URL of XI IS to send the messages to
    XI.TargetURL=http://bwxi:50000/sap/xi/engine?type=entry
    XI.User=XIAF
    XI.Password=XIPASS
    #</b> *************************************************************************************************************
    URL of file adapter if a loopback JMS to File should be configured
    XI.TargetURL=//localhost:8210/file/receiver
    <b># uncomment the following settings if needed (independent on JMS provider)
    JMS.QueueConnectionFactoryImpl.user=xisuper
    JMS.QueueConnectionFactoryImpl.password=xxx
    #</b>
    uncomment and adjust parameters for loading JMS administrated objects via JNDI
    uncomment and adjust parameters if not the default context should be used
    #JNDI.InitialContext.property.1=java.lang.String {javax.naming.Context.INITIAL_CONTEXT_FACTORY}, java.lang.String com.sap.engine.services.jndi.InitialContextFactoryImpl
    #JNDI.InitialContext.property.2=java.lang.String {javax.naming.Context.PROVIDER_URL}, java.lang.String localhost:50004
    #JNDI.InitialContext.property.3=java.lang.String {javax.naming.Context.SECURITY_PRINCIPAL}, java.lang.String Administrator
    #JNDI.InitialContext.property.4=java.lang.String {javax.naming.Context.SECURITY_CREDENTIALS}, java.lang.String sap
    set the Lookup Names
    #JMS.JNDILookupNameQueueConnectionFactory=jmsfactory/default/joetest
    #JMS.JNDILookupNameQueue=jmsQueues/default/sapDemoQueue
    uncomment and adjust parameters for loading JMS administrated objects from filesystem ***
    #JMS.FileNameQueueConnectionFactory=SAPQueueConnectionFactory.ser
    #JMS.FileNameQueue=SAPQueue.ser
    uncomment and adjust parameters for creating SonicMQ JMS administrated objects ***
    JMS.QueueConnectionFactoryImpl.classname=progress.message.jclient.QueueConnectionFactory
    JMS.QueueConnectionFactoryImpl.constructor=java.lang.String localhost:2506
    JMS.QueueImpl.classname= progress.message.jclient.Queue
    JMS.QueueImpl.constructor=java.lang.String SampleQ1
    <b># uncomment and adjust parameters for creating MQSeries JMS administrated objects ***
    JMS.QueueConnectionFactoryImpl.classname=com.ibm.mq.jms.MQQueueConnectionFactory
    JMS.QueueConnectionFactoryImpl.method.setHostName=java.lang.String BWXI
    JMS.QueueConnectionFactoryImpl.method.setChannel=java.lang.String JAVA.CHANNEL
    JMS.QueueConnectionFactoryImpl.method.setTransportType=java.lang.Integer {com.ibm.mq.jms.JMSC.MQJMS_TP_CLIENT_MQ_TCPIP}
    JMS.QueueConnectionFactoryImpl.method.setQueueManager=java.lang.String QM_BWXI
    JMS.QueueImpl.classname= com.ibm.mq.jms.MQQueue
    JMS.QueueImpl.constructor=java.lang.String postcard
    JMS.QueueImpl.method.setTargetClient=java.lang.Integer {com.ibm.mq.jms.JMSC.MQJMS_CLIENT_NONJMS_MQ}
    #</b> *************************************************************************************************************
    uncomment and adjust parameters for using a dispatcher ***
    #Dispatcher.class=com.sap.aii.messaging.adapter.ConversionDispatcher
    #Dispatcher.namespace=namespace1
    #namespace1.ConversionDispatcher.logPayload=true
    #namespace1.Service.1=Plain2XMLService
    #namespace1.Plain2XMLService.class=com.sap.aii.messaging.adapter.Conversion
    #namespace1.Plain2XMLService.xml.conversionType=SimplePlain2XML
    #namespace1.Plain2XMLService.xml.processFieldNames=fromConfiguration
    #namespace1.Plain2XMLService.xml.fieldNames=a,b,c
    #namespace1.Plain2XMLService.xml.fieldSeparator=;
    #namespace1.Service.2=XSLTService
    #namespace1.XSLTService.class=com.sap.aii.messaging.adapter.XSLTConversion
    #namespace1.XSLTService.XSLTConversion.XSLTFileName=Data/DemoConversion.xsl
    Can you please help me in resolving the error.
    Regards,

  • Ping error in RWB for J2SE Adapter Engine

    Hi,
    we have several external J2SE adapter engines and they function great other than from a monitoring perspective. In RWB "Ping Status" I'm getting the following:
    HTTP request failed. Error code: "401". Error message: "Authorization Required"
    Suggestions?
    Cheers,
    Mattias

    <u>This is not an answer to your question.</u>
    I've tried to get an answer for: how to register J2SE adapter with Integration Server ?
    I tried using SLDAccess service on J2SE adapter with no luck (with this J2SE Adapter Engine is registered in the SLD). My J2SE adapter was never available in the configuration means, in the communication channel ex: file adapter, for the adapter engine drop down all I have is Integration Server, my J2SE adapter was never listed there.
    If you know an answer please post.
    thanks
    SKM<u></u>

  • Receiver File Adapter J2SE Adapter Engine

    Hi,
    We have configured a receiver file adapter on a J2SE adapter engine through the administrator page of the J2SE adapter.
    XI.httpPort=8222
    XI.httpService=/file/Receive
    and the rest of the adapter parameters.
    I have configured a channel in ID as XI receiver adapter.
    host: "hostname"
    Service: 8222
    Path Prefix: /file/Receive
    The messages in sxmb_moni fail to be delivered with "HTTP error 404 Resource not found."
    Through a browser I am also not able to make a connection to this url:
    "host":8222/file/Receive
    Getting Http error "501".
    Please can someone shed some light on this problem.
    Regards
    Willie Hugo

    >Through a browser I am also not able to make a connection to this url:
    >"host":8222/file/Receive
    >Getting Http error "501".
    This is ok. Since get method not implemeted for this service.
    Since from XI you are getting this error "HTTP error 404 Resource not found", can you logon to XI server at OS level and do a telnet test to check if the port is working.
    cmd> telnet
    telnet> open <J2SEAdpaterEngineHostName (or) IPAddress> 8222

  • How to get J2SE Adapter?

    Hi all,
    I am planning to use J2SE adapter with NW2004s 7.0. Where do I get the adapter?
    Thanks,
    Prabhu.

    Download the latest patch from service.sap.com/patches
    Deploy this on your XI with SDM.
    Add the libraries servlet.jar and jms.jar to the folder tech_adapter (created during deployment).
    That is all.
    Stefan

  • Registering Plain J2SE adapter in IS

    Hi,
    I've been trying to use plain J2SE file adapter as receiver with no luck.
    I've installed plain J2SE adapter on a windows 2000 server called <b>tgrpser1</b>, and XI is on another Windows 2000 server <b>tgrpserxi</b>.
    SLDAccessor service is started with no error in  <b>tgrpser1</b>.
    When go to the SLD, the adapter engine shows up in the XI technical system but when I go to the Integration Directory to configure a file adapter as receiver for <b>tgrpser1</b>, the <b>Adapter Engine</b> has one value <b>Integration Server</b>.
    Please help...
    Thanks

    I think I should it put this way.
    I have a plain J2SE adapter engine running on <b>tgrpser1</b> (it is not an FTP server), I've copied the <b>file_receiver</b> adapter to <b>rec_File_adapter</b>.
    If the scenario is RFC -> XI -> File (on <b>tgrpser1</b>), how can I specify the <b>rec_File_adapter</b> in Integration Directory.
    If I am not correct, what is the use of plain J2SE adapter engine <b>file_receiver</b> ?
    Thanks

  • Problem: Plain J2SE Adapter Engine

    Hello,
    I have installed the Plain J2SE Adapter Engine.
    On the Adpater Engine running a SOAP Adapter.
    When i try to test the Adapter i become following error Message:
    java.net.ConnectException: Connection refused: connect
         at java.net.PlainSocketImpl.socketConnect(Native Method)
         at java.net.PlainSocketImpl.doConnect(Unknown Source)
         at java.net.PlainSocketImpl.connectToAddress(Unknown Source)
         at java.net.PlainSocketImpl.connect(Unknown Source)
         at java.net.Socket.connect(Unknown Source)
         at java.net.Socket.connect(Unknown Source)
         at java.net.Socket.<init>(Unknown Source)
         at java.net.Socket.<init>(Unknown Source)
         at com.sap.aii.messaging.net.ClientHttpImpl.call(ClientHttpImpl.java:146)
         at com.sap.aii.messaging.adapter.SinglePayloadClient.doPost(SinglePayloadClient.java:222)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
         at com.sap.aii.messaging.adapter.Zone.service(ModuleGUIBrowserEngine.java:1073)
         at com.sap.aii.messaging.adapter.HTTPRequest.run(ModuleGUIBrowserEngine.java:371)
    any idea?
    Regards,
    Robin

    Hi Stefan,
    SOAP Adapter module settings:
    Bubble adapter java class
    classname=com.sap.aii.messaging.adapter.ModuleBubble
    This adapter instantiates a bubble bag for supporting
    a xmb web service gateway. A bubble bag is a collection of Bubble
    instances that form some processing chain of message objects.
    Below parameter Bubble.Helper specifies the helper class that implements
    the ModuleBubbleHelper interface. This class is used to instantiate
    a bubble bag for this adapter.
    Sets the bubble module helper that can instantiate your bubble bag
    Bubble.Helper=com.sap.aii.messaging.adapter.ModuleBubbleHelperXMBWSImpl
    #$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
    Below this line are the parameters specific to the ModuleBubbleHelperXMBWSImpl
    #$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
    The configuration of this helper class is divided in two parts. The first part
    specifies the adapter configuraton for Web-Service clients communicating with an
    XMB server. The second part specifies the configuration for XMB clients
    communicating with a WebService server. Either one or both parts can be configured
    in a single configuration file.
    Part 0 (FromWS and ToWS) : common part ######
    Keeps the XMB headers in web service messages
    XMBWS.KeepHeaders=true
    Keeps the attachments in web service messages
    XMBWS.KeepAttachments=false
    Encodes the xmb headers into a special HTTP header string x-xmb_ws_encoded
    XMBWS.UseEncoded=false
    Part 1 (FromWS) : WS clients to XMB server ######
    The target URL of XMB broker, to which the adapter sends XMB messages.
    XMB.TargetURL=http://netweaver:8000/sap/xi/engine?type=entry
    The port and path where the adapter waits for web service messages from clients.
    XMBWS.WSPort=4444
    XMBWS.WSPath=/soap/start
    The following XMB attributes are used to fill default XMB messages.
    XMB.SenderBusinessSystem=MOS_BS
    XMB.SenderInterfaceNamespace=ns:moskau
    XMB.SenderInterfaceName=MOSOut
    XMB.QualityOfService=BE
    now i have an other error message.
    com.sap.aii.messaging.net.TransportException: HTTP 500 Internal Server Error
    http-Response:
    content-type: text/xml
    content-length: 349
    content-id: <[email protected]>
    <SOAP:Envelope xmlns:SOAP='http://schemas.xmlsoap.org/soap/envelope/'><SOAP:Body><SOAP:Fault><faultcode>SOAP:Server</faultcode><faultstring>com.sap.aii.messaging.srt.BubbleException: Can't call the endpoint; Exception raised by com.sap.aii.messaging.net.TransportException: Content-Type not set</faultstring></SOAP:Fault></SOAP:Body></SOAP:Envelope>
         at com.sap.aii.messaging.net.ClientHttpImpl.call(ClientHttpImpl.java:337)
         at com.sap.aii.messaging.adapter.XMBTestClient.doPost(XMBTestClient.java:236)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
         at com.sap.aii.messaging.adapter.Zone.service(ModuleGUIBrowserEngine.java:1073)
         at com.sap.aii.messaging.adapter.HTTPRequest.run(ModuleGUIBrowserEngine.java:371)

  • Standalone (J2SE) adapter - axis SOAP adapter - issue duplicate messages

    All,
    Perhaps you can help me. I've setup a scenario where an standalone (J2SE) adapter sends a file to SAP XI channel, configured on the central adapter engine, of type SOAP configured to use Axis servlet.
    The connection is setup and the standalone adapter channel logs thre response from the SOAP channel which reads HTTP error 500, indicating a duplicate message.
    SAP has identified this problem and proposes in the FAQ for Axis (note 1039369) to set on the SOAP channel module CallSapAdapter property ignoreDuplicate to true in the module processor.
    I've implemented this as suggested however found the problem persists. I'm still receiving an HTTP 500 error.
    Your help is much appreciated solving this problem.
    Thanks
    Harald

    As there was a bugfix recently, make sure that you have installed the latest patch.
    If this does not work, open an OSS ticket for this issue.
    Stefan

Maybe you are looking for

  • My photo stream web page is in the wrong order

    I've been using the photo stream to share photos with family via the web link. Until today, it was working perfectly. Today, the order of the photos suddenly rearranged themselves with no action on my end. I haven't uploaded any photos in several day

  • Aggregates on Technical Content

    Hi Guru's, I have installed the Technical Content Cube ( 0BWTC_C05) ,which is for ware house performance monitoring, Now I have to create a process chain to load data into this Infocube. As we are not using the Multiprovider,we cant have the standard

  • FMS Newbie ?'s

    Hi, I am very proficient with Flex and Flash, however I am new to FMS. I have never setup a Media Server, and have never programmed a Flash/Flex Video Streaming Application. However, I have a client who needs to have a password-protected page to view

  • How to change branding image of Portal?

    Hello All, This topic may sound very common to you al but i have tried soem basic steps but no success so i am posting this thread. I want to change branding image of portal log on page. I have navigated to this path. S:\usr\sap\EPD\JC00\j2ee\cluster

  • Woh - anybody else seeing this?

    Is anyone else seeing this? How am I supposed to contact "System Administrator"? Error An error in the system has occurred. Please contact the system administrator if the problem persists. Useful links : Forum Home -- browse the forums here. Search F