Gateway 24" HD LCD Widescreen Monitor

Hello,
Can I plug a Gateway 24" HD LCD Widescreen Monitor into my iMac G5 with iSight and get maximum benefit from the resolution of 1920*1200 ?
Thanks,
John.

You should also be aware that the display will be a mirror of internal display and will not provide any additional space.
Apple has disabled dual-displays and only the hack can open that up.
mrtotes

Similar Messages

Gateway 21" cinema LCD monitor and my PowerPC G4.

My story: I just bought a Gateway 21" LCD Cinema monitor (FPD2185W) to use for both my mac(DVI) and my PC(serial).
My problem: The native resolution is at a maximum 1280x1024 and my screen is super stretched on my MAC, but everything was fine on the PC side.
What I need: To find a way to increase the resolution to the LCD monitors maximum size (1650x1050) on my Mac so its not stretched anymore....is there anyway I can do this? I don't see any support what so ever from Gateway, which isnt too surprising, but nothing really from any Mac sites either.

Hi,
I don't know which Mac model you have, look here and find your machine. When we know which it is I can make a few suggestions.
http://docs.info.apple.com/article.html?artnum=58418
http://docs.info.apple.com/article.html?artnum=42739
In truth, Mac's are cake to install a video card. Remove the old, install the new - that's it. Some ATI cards can benefit from the ATI software, so follow directions if you get one.
The downside is that there are very few new video cards available for Mac's, the prices tend to be higher than for PC's.
When you know which Mac model you have, look at OWC's available video cards. That will give you an idea what the prices are. Of course, you can try the auction site.
http://eshop.macsales.com/
Regards,
Dave

Acer - 19" Widescreen Flat-Panel LCD HD Monitor

I have a question about the Acer - 19" Widescreen Flat-Panel LCD HD Monitor.
The link to the product:
Acer- 19" Widescreen
Under "Whats Included" it only says:
Acer 19" Widescreen Flat-Panel LCD HD Monitor
Owner's manual
Does that mean a power cord, and the cord to connect it to your computer isn't included, since its not listed under Whats Included? Or is it just a given that those two things are included, thus they dont waste time writting it out.
Hopefully I can get an answer before this deal goes away!
Thanks

Of course they do
There are no manufacturers that would sell monitors without the required things to run them!
The only exception is printers or television where they always make you buy the cables ...
*******DISCLAIMER********
I am not an employee of BBY in any shape or form. All information presented in my replies or postings is my own opinion. It is up to you , the end user to determine the ultimate validity of any information presented on these forums.

Widescreen monitor benefits???

I currently have a 2-3 year old flat panel LCD 17" monitor but with price drops was thinking of going with a widescreen monitor, are there benefits, or will my Windows XP and internet look funny on the widescreen since I have an older computer? I heard the internet is still in "full-frame" mode, is this true, would I just do better keeping my 17" regular size?
THANKS!
Solved!
Go to Solution.

Widescreen monitors offer several advantages for those who use their computers as entertainment machines. For those who want a truer picture of the way a movie was intended to be displayed, without the minimizing and annoying letterboxes, a widescreen monitor is essential. Further, many computer games are also shot in a widescreen format. While it may be possible to play these games on a monitor with a more traditional ratio, it is not the intention of the producer.
mae
sydney seo

External widescreen monitor

I just bought a hannspree widescreen monitor for my pb since the screen has been acting up. I'm using a hdmi to dvi cord. problem is im only getting a letter box view. It is not stretched out. Is there anyway to expand it so it will fit the entire screen?

If you mirror, you won't be taking advantage of the widescreen, since it will be forced to the lower resolution of the eMac's screen, so I see little point in having a big widescreen. A 17" at 1024x768 would do the same, be sharper, and cost less (you might find a 19" that does 1024x768, but they're a bit rare).
You'll need a miniVGA to VGA adapter, and of course a VGA-capable LCD.

CS6 Firewire 16:9 preview is letterboxed on widescreen monitor

With CS6, is there a setting to fix the Firewire Preview since the 16:9 video is incorrectly letterboxed on a widescreen video monitor? It is basically letterboxing something that doesn't need to be letterboxed.This is for a 1080 24p AVCHD project with 1080 24p video files.
Adobe Encore & After Effects CS6 properly dsiplay the Firewire Preview on a widescreen monitor.
In Encore, there is acctually a setting in the Preview Menu that lets you change the TV Mode from 16:9 to 4:3 Letterbox. That only affects the preview when choosing to the Preview the DVD. When playing the video from the Timeline or clicking on a DVD Menu that setting doesn't change how the Firewire Preview displays and is always 16:9. Premiere is always 16:9 letterboxed.
Any suggestions on how to get Premiere to display 18:9 using Firewire Preview without letterboxing it?
Randy

I checked it using various Firewire devices but they all act the same in this situation. Pioneer DVD recorder, Sony DV camcorders.
The unique thing with Premiere CS6 compared to CS5.5 or earlier versions is that it allows Firewire previews with the Mercury GPU on, it doesn't force you to turn that feature off and use the Mercury Software setting instead which is lower performance if you have the proper video card.
I just checked it using Premiere CS5.5 and it does the same thing. In 1080 HD Sequences, Firewire out has the 16:9 incorrectly letterboxed, or what I call "double" letterboxed.
With both CS5.5 and CS6, the Firewire preview is correctly displayed in a DV 480i 16:9 Widescreen Sequence.
A little annoying but this is where an old Sony PVM 4:3 broacast video monitor works well in combination with a widescree 16:9 video monitor still. Simply turn off the 16:9 mode and it will dsiplay it correctly when editing an HD Sequence. When using a DV widescreen Sequence you would then click on the Sony PVM's 16:9 mode so it would letterbox correctly.
Surprised Adobe didn't fix this in Premiere CS6
Randy

M30: FX G05200 + external Widescreen Monitor: Resolution 1440x900 not available

Hi!
I`ve got the following problem:
I`d like to connect a external TFT Widescreen Monitor with a native resolution of 1440x900 to my Satellite M30 with a GeForce FX Go5200.
But: It is not possible to adjust the resolution of the Graphics Card to 1440x900 (16:10), there are just standard resolutions (4:3) available.
I tried nearly everything:
- installed Monitor Drivers ==> no effect
- updated Drivers for the Go5200 (to 4644) ==> no effect
- updated Bios (to 1.7) ==> no effect
- Tried RIVAtuner and PowerStrip ==> no clue = no effect
Now Im pretty helpless and I dont know what to do...
Maybe someone faced the same problem here and found a solution.
Thank you for your help.
Christian

Got the solution:
http://www.laptopvideo2go.com/forum/index.php?showtopic=9243

Can't get widescreen monitor to work right.

I can't get my widescreen monitor too work right.
It should be at 1360x768 res but it is at 1024x768.
I'm using a mac mini.
My monitor is manufactured by LG, it is a flatron. xrandr -q gives
Screen 0: minimum 640 x 480, current 1024 x 768, maximum 1024 x 768
default connected 1024x768+0+0 0mm x 0mm
1024x768 0.0*
800x600 0.0
640x480 0.0
I'm sorry if this is a noobie issue, I wouldn't know. I hope someone will please help me. thank you.

Is your video driver right for your system? Which driver are you using right now?

I cannot afford an iMac, can anyone recommend a widescreen Monitor for my 15" MacBook Pro. It would be used mainly for iPhoto and Aperture.

I cannot afford an iMac, can anyone recommend a widescreen Monitor for my 15" MacBook Pro. It will be used mainly for iPhoto and Aperture. TF

Pair a wireless KB with the laptop and all should be well when you attach the laptop to the iMac and invoke TDM. But as Denny mentions, it does seem like the waste of a good iMac to use it in just this configuration. Why is the laptop primary?

New Mac Mini, Not so new LCD HDTV Monitor, no mac support

I have been attempting to set up a Mac Mini with a Maxent LCD 26" HD TV I can't get either the RGB or DVI-D input to accept signal. I have purchased DisplayConfigX and SwitchResX_X. Maybe they could work, but I can't get a signal to stay on long enough to change the settings as listed in other posts. I have tried booting in safe mode as DisplayConfigX instructions suggest. But still only am able to see the screen until gear starts spinning with apple logo, resolution changes spontaneously to one that I suppose is unsupported and I get the unsupported display and a beautiful blank blue screen. I tried manually inputting the resolutions the monitor manual lists, while connected with an lcd pc monitor. But I can't get the Maxent LCD TV monitor to stay on. It appears that if I could get the Mac Mini to send this resolution signal to the Maxent I would be able to delete any unneeded settings and that would be it.
Perhaps Tom Fussy can help me.I have been at this for over two weeks now. So I have become super frustrated. Of course Maxentusa.com offers no Mac support. But state that if Mac mini is supposed to work with PC that it should work with my Mac Mini. My LCD TV is about 6 months old I could still return it for maybe a Sharp Aquos, if that $300 dollar more TV would work. I am happy with the Maxent otherwise. Keeping it, and having it work with Mac Mini Is my choice. Of course Apple offers no support for the Maxent monitor and directed me here. This is my first discussion group post. School me if I have not followed the rules completely.

I was able to get the settings for Maxent using Gregory's software to force 640x480. Here are my settings
DDC block generated by SwitchRes X for display
MX-26X3
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 | 00 FF FF FF FF FF FF 00 34 38 35 08 06 44 00 00
1 | 0C 0F 01 03 0F 3A 20 78 88 00 0D 00 00 00 00 00
2 | 00 47 4A BD CE 00 31 59 45 59 61 59 81 80 81 C0
3 | D1 C0 01 01 01 01 FF 1D 56 EA 50 00 20 30 46 28
4 | 55 00 40 44 21 00 00 18 8C 0A D0 8A 20 E0 2D 10
5 | 10 3E 96 00 40 44 21 00 00 18 00 00 00 FD 00 3C
6 | 55 1F 45 0B 00 0A 20 20 20 20 20 20 00 00 00 FC
7 | 00 4D 58 2D 32 36 58 33 0A 20 20 20 20 20 00 2D
Valid DDC block: checksum passed
EDID Version........1.3
Manufacturer........MAX
Product Code........13576 (3508) (0835)
Serial Number.......17414
Manufactured........Week 12 of year 2005
Max H Size..........58 cm
Max V Size..........32 cm
Gamma...............2.20
DPMS Supported Features:
Standby
Display type:
RGB color display
Input signal & sync:
Analog input with: 0.700V / 0.300V
Serration Vsync
Sync on green
Separate Sync
Composite Sync
Color info:
Red x = 0.000 Green x = 0.000 Blue x = 0.000 White x = 0.280
Red y = 0.000 Green y = 0.000 Blue y = 0.000 White y = 0.290
Established Timings:
800 x 600 @ 60Hz
640 x 480 @ 75Hz
640 x 480 @ 72Hz
640 x 480 @ 67Hz
640 x 480 @ 60Hz
720 x 400 @ 70Hz
1024 x 768 @ 75Hz
1024 x 768 @ 70Hz
1024 x 768 @ 60Hz
800 x 600 @ 75Hz
800 x 600 @ 72Hz
Manufacturer Reserved Timings:
Standard Timing Identification:
#0: 640 x 480 @ 85Hz (3159)
#1: 800 x 600 @ 85Hz (4559)
#2: 1024 x 768 @ 85Hz (6159)
#3: -768 x -614 @ 60Hz (FFFF8180)
#4: -768 x -432 @ 60Hz (FFFF81C0)
#5: -128 x -72 @ 60Hz (FFFFD1C0)
Monitor Description blocks:
Descriptor #0 is Timing definition:
Mode = 1366 x 768 @ 60Hz
H. Active...............1366 pixels
H. Blanking.............234 pixels
V. Active...............768 lines
V. Blanking.............32 lines
HSync Offset............70 pixels
HSync Pulse Width.......40 pixels
VSync Offset............5 lines
VSync Pulse Width.......5 lines
Pixel Clock.............76.79MHz
Horizontal freq.........47.99kHz
Vertical freq...........59.99Hz
H Image Size............576mm
V Image Size............324mm
H Border................0 pixels
V Border................0 lines
Non-Interlaced
Sync: Digital separate with
* Negative vertical polarity
* Negative horizontal polarity
Descriptor #1 is Timing definition:
Mode = 720 x 480 @ 60Hz
H. Active...............720 pixels
H. Blanking.............138 pixels
V. Active...............480 lines
V. Blanking.............45 lines
HSync Offset............16 pixels
HSync Pulse Width.......62 pixels
VSync Offset............9 lines
VSync Pulse Width.......6 lines
Pixel Clock.............27.00MHz
Horizontal freq.........31.47kHz
Vertical freq...........59.94Hz
H Image Size............576mm
V Image Size............324mm
H Border................0 pixels
V Border................0 lines
Non-Interlaced
Sync: Digital separate with
* Negative vertical polarity
* Negative horizontal polarity
Descriptor #2 is Monitor limits:
Horizontal frequency range.......31-69 kHz
Vertical frequency range.........60-85 Hz
Maximum bandwidth unspecified
Descriptor #3 is Monitor name:
MX-26X3
Mac Mini 1.42 g, superdrive, ATI 9200 Mac OS X (10.4.2)

Your Suggestions on Adding External LCD / LED Monitors to MacBook Pro?

My current work station is a PowerPC G4 Dual 867Mhz with dual 19" CRT displays. I use this for design work (Adobe Illustrator); photo restoration (Photoshop); & online sales.
I was down to my last two CRT monitors, and wanted to perhaps start porting some of the graphic intense work to a faster computer so I bought this MacBook Pro:
http://support.apple.com/kb/SP499
I have not actually had a chance to use the MacBook Pro - it and all the accessories are still sealed - I couldn't afford the down time to set it up.
I am wanting to add a external monitor to the MacBook Pro that would be suitable for detailed design work with accurate color, true blacks, and the ability to be correctly calibrated. Since I may be still doing work on the G4 with software that will not run on the MacBook Pro I'd like to perhaps buy 3 matching monitors , 2 to replace my crt units and 1 for the MacBook, so that I can closely match the design output between the G4 and MacBook Pro.
I briefly tried a inexpensive LCD TV with a PC hookup on the G4 to get some idea of how an lcd would look. The LCD TV had a native resolution of 1440 X 960, which is a 3:2 aspect ratio, but that resulted in designs elements being distorted (i.e., squares look like rectangles). In 4:3 mode the TV did not distort the design elements, but the picture was not crisp / sharp and appeared soft. From what I've read this is because the lcd, unlike a crt, can't correctly emulate resolutions other than the native resolution built into the screen (i.e., its software guesswork). I also did not like the fact than in 4:3 mode it left black areas on the right and left edges of the screen.
I typically work in a 4:3 aspect ratio with a resolution of 1024 X 768, but a higher resolution of say 1600 X 1200 would be o.k. So what are your suggestions as to finding a lcd / led monitor that has a 4:3 aspect ratio? So far I've found limited information on what appear to be old monitors - there's one on Dell's site; for example, that says it has 1600 x 1200 native resolution, but a review also says its the same monitor they've been making for 5 years (besides I don't think I'd like the idea of hooking a Dell into my Mac). Found a few references to Lacie and NEC.
I really don't understand the monitor manufacturers, including Apple, that claim their monitors are for design work, when they don't offer native a 4:3 aspect ratio. How exactly am I to complete designs when circles are ovals and squares are rectangles?

"Take a flash drive with some representative PDF files saved from Illustrator to your nearest Apple Store or Apple reseller and ask for a demonstration using one of Apple's beautiful 27" 2560 x 1600 monitors. It would replace both of your 1024 x 768 CRTs with lots of additional desktop real estate to spare."
1. Well, actually no since I do not have fixed 1024 x 768 crts since crts do not have fixed resolutions. I can easily set each monitor to a variety of other resolutions including 1600 x 1200. Actually the Apple display would be a step down in total working area if I used the largest common resolution of 1792 x 1344 and certainly not worth the extra cost for the space gained if working at 1600 x 1200.
2. Unfortunately the display requires 10.6, which does not work on a G4 Dual 867Mhz. It would not even work on my MacBook Pro that I've not had a chance to use yet as it comes with 10.5. Also, 10.6 drops supports for PowerPC emulation so that means buying hundreds of dollars in new software. I use Apples only, but one thing I hate about the company is what many perceive is their "elitist attitude" toward their users - do they really think most people in the real world have so much money that in order to use Apple's new 27" display that they have to go out and spend more than the display costs on updating their computer and software. I am not a zombie fanboy willing to buy anything just because it has Apple on it.
3. Like most people I do not live by an Apple store or a Apple reseller, even the local Best Buy does not carry Apple computers in their store because the retail space does not justify the resulting sales (not that I would buy anything there anyway as they are over priced). I am really not interested in driving several hundred miles to the nearest store.
4. For a $1,000 I expect a monitor to offer a native 4:3 (1600 x 1200) aspect ratio - certainly Apple knows that this is the preferred working environment of many CAD and graphic users but they chose not to offer this in the display, thus the Apple display is really seems geared toward pop corn munching movie watching consumers.
5. This display is not actually made by Apple, its probably LG or one of their other suppliers.

Extrnal widescreen monitor problems

Hi
I Have recently bought a 19 inch widescreen monitor Acer AL1916w and the resolution setting is 1440 x 900 which comes up as well as the name of the monitor when it is plugged in, however it doesnt expand the full size of the screen it 's about the same size of my powerbook screen, it works on the 1024 res but obviously the quality is bad.
Please Help
Thanks stiltcreature

Hi,
if you mirror your internal display this behaviour is normal. have you pressed F7 once to switch to dual display ?
Volker

Good low-cost widescreen monitor for one-screen editing?

Hello, I'm on a tight budget, looking for a widescreen monitor that is a good blend of low-cost but good quality (if possible!).
I will be doing all my work off this single monitor. I will unfortunately NOT be able to have a dual-monitor setup, nor have an external reference monitor. I will be editing HDV footage.
Any suggestions? Thanks!

It is a PVA screen with dual DVI and a D-sub connector.
I use three of them and they give me a good BFTB, "Bang-for-the-Buck".
If you consider the various panels in use, they go from low to high in quality, TN >> PVA >> IPS.

Powerbook with Syntax Olevia 23-inch LCD TV Monitor

Hi there,
I got a 23-inch LCD TV Monitor from Syntax Olevia and somehow it doenst work with my powerbook.
The thing is when I connected it to my windows laptop, it worked just fine, I should say perfectly instead. Then I tried it on my Powerbook 12-inch, the Mac recognized the display, there was a VGA display on but when I turned the display on, it says 'NO PC SIGNAL'. You know, I'm ****** !
I have been on the phone with Syntax Tech Support for an hour, then with Apple for another hour, they suggested me to do everything try to get it works, everything they could find, everything within thier knownledge.... COULDNT CHANGE ANYTHING!
So the last thing the Apple guy suggested me is post a topic question here, to see what everyone says and if somebody out there has got the same problem, please do reply so, even you got it worked or not, just reply so I can have some experience. It might be compatibility problem but I don't know, not with a monitor I would say.
So here the LCD name and brand:
- Olevia 23-inch LT23HVX by Syntax.
I would appreciate for any answer, I'm looking forward to it.
Thanks all
Powerbook G4 12' Mac OS X (10.4.5)

Hi,
I'm not familiar with that monitor, but its resolution might be higher than your PowerBook can handle. I have a first-generation 12-inch PowerBook, and it seems that it can't run any of the Apple Studio monitors currently being sold. If that monitor can display a resolution of 1024 x 768, try that, as your PowerBook can certainly handle that resolution. Another thing to try is to see if you can find a friend or coworker who has a similar PowerBook (or any other Mac), so you can try connecting the monitor to that machine to see if there is a similar problem. If no Mac can drive it, you would probably have a good excuse for returning the monitor.
Hope this helps,
Ken

Mac book and "Acer X191WSD 19" Widescreen Monitor"

Hello Guys
I just got a new "Acer X191WSD 19” Widescreen Monitor" and tried to hook my macbook with the external monitor, using mini dvi to dvi cable. When I hooked my Pc to the external monitor (using vga) it recognized the setting and automatically recognized and resized it. But not with Macbook. I played around for some time, at last it did recognize my macbook, but there is only a background of my desktop (not my icons--just a blue one). But when I mirrored my macbook to ext monitor, it worked fine. I donot want to mirrored.
Is it possible to use my ext monitor as my macbook monitor (with out mirroring and not extension of my monitor macbook + ext monitor).
The reason is that, it looks annoying when I want to watch a DVD/Movie on the ext monitor
Thx for your help guys
C

One thing that just clicked in my little pea brain. When you first hook up your external monitor in extended mode it will only have the blue background. This allows you to drag any windows and other stuff over to it. I keep two finder windows open and mail open on my external.

Gateway 24" HD LCD Widescreen Monitor

Similar Messages

Maybe you are looking for