Get MTP to work on NWZ-E384

I have this Sony mp3 player. When plugged into windows it automatically enters MTP mode. On Linux, it doesn't though. (It goes into MPS mode.) The mtp-detect command finds nothing. How can I get it to? Is it possible?
Last edited by sethradio (2014-06-18 04:13:35)

I just installed go-mtpfs-git and it doesnt work either. Here is what I get:
$ go-mtpfs Android
2014/08/31 22:17:10 OpenSession failed: LIBUSB_ERROR_TIMEOUT; attempting reset
2014/08/31 22:17:16 Configure failed: OpenSession after reset: LIBUSB_ERROR_TIMEOUT

Similar Messages

Can't get MTP to work on one of my laptops - x86_64 & KDE

I have Arch x86_64 on both of my laptops. The newer one of the two can't seem to get MTP to work on my Galaxy Note III. Both laptops run KDE and use kio-mtp. I have looked around quite a bit and can't figure this one out.
user groups:
wheel uucp locate games ray sudo fuse networkmanager
Trying to access from command line:
# mtp-detect
Unable to open ~/.mtpz-data for reading, MTPZ disabled.libmtp version: 1.1.6
Listing raw device(s)
Device 0 (VID=04e8 and PID=6860) is a Samsung Galaxy models (MTP).
Found 1 device(s):
Samsung: Galaxy models (MTP) (04e8:6860) @ bus 1, dev 3
Attempting to connect device(s)
PTP_ERROR_IO: failed to open session, trying again after resetting USB interface
LIBMTP libusb: Attempt to reset device
LIBMTP PANIC: failed to open session on second attempt
Unable to open raw device 0
OK.
$ mtpfs -o ~/mtp
Unable to open ~/.mtpz-data for reading, MTPZ disabled.Listing raw device(s)
Device 0 (VID=04e8 and PID=6860) is a Samsung Galaxy models (MTP).
Found 1 device(s):
Samsung: Galaxy models (MTP) (04e8:6860) @ bus 1, dev 3
Attempting to connect device
PTP_ERROR_IO: failed to open session, trying again after resetting USB interface
LIBMTP libusb: Attempt to reset device
LIBMTP PANIC: failed to open session on second attempt
Unable to open raw device 0
Trying to access using Dolphin:
Address Bar:
mtp:udi=/org/kde/solid/udev/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/
Red message box:
"The process for the mtp protocol died unexpectedly"
Address Bar:
camera:/Samsung%2520Galaxy%2520models%2520(MTP)@usb:001,008/
Red message box:
Could not read. Reason: Could not claim USB device.

I just installed go-mtpfs-git and it doesnt work either. Here is what I get:
$ go-mtpfs Android
2014/08/31 22:17:10 OpenSession failed: LIBUSB_ERROR_TIMEOUT; attempting reset
2014/08/31 22:17:16 Configure failed: OpenSession after reset: LIBUSB_ERROR_TIMEOUT

Bought Zen Micro to replace Zen Nano Plus - Can't get it to work

HiSorry if this was answered somewhere, but maybe i'm just dense. Can't seem to get things going. I used to have a Zen Nano Plus which worked fine on my PC - Win XP SP2.Picked up a used Zen Micro - I thought that it would be better because of bookmarking - but I have yet to get it to work.Zen Micro says Version 2.20.05?Here is a list of what it says is loaded on my PC[Creative Product-PID][Installation Log]
8 May 2006, Creative Zen Nano Plus Pack
8 May 2006, Creative MediaSource Zen Nano Plugin .00.07
8 May 2006, Zen Nano Plus Media Explorer 2.00.0
8 May 2006, Creative Audio CD Ripper .60.0
7 May 2006, Creative MediaSource Plugin for CD Burner 3.0.8
7 May 2006, Creative MediaSource Player/Organizer 3.30.2
7 May 2006, Common Audio Driver Interface .03.29
3 May 2006, MediaSource AudioSync Plugin .0.03
3 May 2006, MediaSource NOMAD Jukebox 2/3/Zen Plugin .0.03
3 May 2006, Creative Music Store Plugin .00.09
3 May 2006, Creative MediaSource Zen Nano Plugin .00.03
3 May 2006, Creative MediaSource Player Skin Pack .0.06
3 May 2006, MediaSource NOMAD MuVo Plugin .0.0
3 May 2006, MediaSource CD-ROM Burner Component 3.0.
3 May 2006, MediaSource Detector 3.00.7
3 May 2006, Common Audio Driver Interface .03.
3 May 2006, Creative MediaSource 3.20.57
3 May 2006, Audio Device Selection .0.05
3 May 2006, Creative System Information .0.3
3 May 2006, Zen Nano Plus Media Explorer .0.03
3 May 2006, Creative Audio CD Ripper .60.06
Have tried to download drivers and software for Zen Micro. When I try to run it though, it does not install because it says that I do not have device connected. Have erased everything off of Zen Micro, but have not reformatted. When I attach Zen Micro to PC, Zen Micro displays "booted" & PC displays "Zen Micro" for a second or two, then switches to "MTP Device"?. Do I need to erase everything from the Zen Nano Plus first?2. What do you think my next step should be?Thx???

Welcome to the Apple community.
If you are referring to adding a secondary account, to a single device, then you can do this at system preferences >mail, contacts & calendars.

Apple Mini-DVI to Video Adapter - Can't get it to work!

Bought the Apple Mini-DVI to Video Adapter to hook up my Macbook to my TV. I tried it when it first arrived and it worked within minutes of setting up. Great! I go to set it up and use it again a week later, and it wouldn't work at all. I went through every possible setting I could to try and get it to work, nothing. Do these things have a tendency to go out or short out or something? I'm getting nothing but scrambled screens, grey screens, etc. Nothing seems to work.
http://store.apple.com/us/product/M9319G/A?mco=MTY3ODQ5OTY
Any other solutions for playing my laptop on my TV?

Hey Rob,
Is your profile information accurate? The MacBook 2,1 was introduced in November of 2006 and discontinued in May of 2007, so the mini-DVI to video adapter ought to work.
What, exactly, do you see on your screen? Are all of the connections nice and snug? Do you have another RCA cable you can try? You can use a white or red one if you want; they all will work as long as you're connecting the video adapter to the yellow port on the TV.
~Lyssa

IOS Remote Desktop app and computers connected to SBS 2008--can't get it to work

I can connect directly to the server without a remote resource in the IOS app.
But I'd like to be able to connect to computers in the office like we can through RWW. RWW works fine, but not from my phone. (Yes I can connect to the server and take over computers from the phone but I don't want other people in the office to log
into the server first!).
I can never get the remote resources section in the app to connect. I usually get "Unable to locate any remote resources for the URL". error in the resources section. I've tried a simple "https://remote.domain.com", "https://remote.domain.com:987",
etc.
We have a self-signed certificate. I can't think of anything in the server setup that is anything other than normal.
I can do direct connect using "Remote Desktop Connection" in windows 7. In the remote desktop server settings I just put remote.domain.com and "Ask for password (NTLM)" for the login method. Then on the general tab I have just the
simple computer name and the domain\username. That's all I had to setup to get that to work.
Any suggestions?

Hi Michael,
Thank you for posting in Windows Server Forum.
Have you setup RD Gateway server in your environment? Are you trying to access the RWW through it?
On server side you can choose “Bypass RD Gateway server for local addresses” under RemoteApp manager and check the result.
For more information, you can check below links for detail.
Remote Desktop Client on iOS: FAQ
http://technet.microsoft.com/en-us/library/dn473015.aspx
Getting Started with Remote Desktop Client on iOS
http://technet.microsoft.com/en-us/library/dn473013.aspx
Hope it helps!
Thanks.
Dharmesh Solanki

Have entrourage and want to use Mail. Can't get it to work.

I had a macbook and purchased the Microsoft office for Mac which included Entrourage.
I have now purchased a new macbook Pro and want to begin to use Mail rather than Entrourage.
I have Entrourage on my new computer but i can't get it to transfer my information to the the Mail program
I am on Charter.net at my office and sbcglobal.net at home.
How can i get this to work. I can receive on Mail, but i can't send.

check your outgoing port settings and make sure it's using a specific port and not the default port, also you might want to check to see if it is using SSL, TLS or any other encryption. Verify the setting from your old machine setup.

Got my password wrong twice and my mini is disable. I connected to iTunes, but can't get it to work. Can some one guide my through?

got my password wrong twice and my mini is disable. I connected to iTunes, but can't get it to work. Can some one guide my through?

If it's showing the red disabled screen due to incorrect passcodes then you may need to put the iPad into recovery mode : http://support.apple.com/kb/ht1808 - you should then be able to reset the iPad via your computer's iTunes and restore/resync your content to it

HT1151 i have a new apple external dvd drive, and i can't get it to work with my iMac?

I have a new apple dvd drive, I was told it will work with my imac, but when i plug it in ...nothing... iv been for update... still nothing. How can i get it to work???

If it is this drive, note that it is for MBA's and Mini's only:
http://store.apple.com/us/product/MC684ZM/A
Ciao.

HT1203 iTunes: How to share music between different accounts on a single computer - I tried to use the instructions to configure 2 different windows users sharing the same iTunes library. I could not get this to work per the instructions.

I tried to configure 2 windows users accounts using a single library per the instructions in HT1203. My iTunes library is on an external drive. I cannot get this to work. Any suggestions?

To give other users read-only access to your iTunes library, use the Sharing features of iTunes. Sharing works over the local network as well as on the same computer. See the built-in help for details.
If you want to give full read/write access to more than one user, see the support article linked below.
iTunes: How to share music between different accounts on a single computer
There is a way to share the library without moving it to a secondary volume. If you really need to do that, ask for instructions.

I have 2 ipod touch's that both have frozen screens and will not reset or show up in itunes. They both froze after trying to update to the latest software version. How do I get them to work?

I have 2 touch's that froze when trying to update to the latest ios version. Neither respond to restarting the devices. They are also not recognized in windows or itunes. How do I get these to work. I followed all of the instructions on the apple website and they still don't work. I have verified that I have apple support for mobile devices installed in itunes and my version of itunes is 11.0.1. I am running windows 7 64bit with service pack 1 installed and all of my updates are current. Is anybody else having this problem with their apple devices?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

I could not get ExportPDF to work. Something about a network error when trying to sign in.

I could not get ExportPDF to work. Trying to convert a pdf to a Word document. Got an error message. Something about a network error when attempting to sign in.

Try the following:
1. Reset
Hold the Sleep and Home button down until you see the Apple logo
2. Restore:
http://support.apple.com/kb/HT1414
3. Recovery:
http://support.apple.com/kb/HT1808

Can not use all the tools in my drawing markups any ideas on getting them to work?

Can not use all the tools in my drawing markups any ideas on getting them to work?

Hi tonys60181,
Could you please let me know what version of Adobe Acrobat are you using.
What all drawing tools are you unable to access?
Is this issue specific to one PDF file or all?
What exactly happens when you try to use any drawing markup?
Please let me know.
Regards,
Anubha

I purchased and downloaded Photoshop Elements 13, but the installer fails to initialise. How do I get it to work?

I have Photoshop Elements 10 and Premier Elements 10 installed on my PC. Both were installed from discs that I bought a few years ago. I recently purchased the upgrade (by download) for both applications to version 13. In accordance with the (scant) instructions received by email, I downloaded the four files required from the Adobe site. I subsequently ran the .exe files, which in turn created directories on my PC, including set-up.exe files for both applications. When I run the setup files, I get an error message stating that the installer failed to initialise. The error message advised me to download the Adobe Support Advisor to detect the problem. That tool does not exist. I then sought assistance from the Abobe support site, initially using the hyperlink suggestions, which were of no use, then using the chat function. The operator kept trying to get me to do something with something called 'Creative Cloud'; which I am not familiar with, and do not use. He then instructed me to download and run a CS5 cleaner tool; however, none of the choices offered by that tool include my issue, or either Photoshop Elements or Premier Elements. I am reluctant to uninstall version 10 of the programs in case I end up losing the lot and therefore wasting even more money than the purchase price for this upgrade.
All I want to do is upgrade my two applications from version 10 to version 13. I have paid the requisite fee but it clearly does not work. I appear to have totally wasted my money. Can anyone please tell me how to get it to work? I do not want to have anything to do with the so-called ‘Creative Cloud’ as I have no idea what it is, and I do not want to lose what I already have (and have paid for previously).
I have tried for a few days to access the so-called 24/7 chat assistance but appeared to have been locked out as every time I try to access it, I get a message that the (24/7) chat is closed. Adobe has taken my money for a product that does not work, and also refuse to help me fix it.
I am very frustrated with a product I bought that does not work, and a 24/7 support service that clearly is not 24/7, and which refuses to assist me. Can anyone PLEASE tell me how to get this to work? Rod.

Hi,
Can you please share the logs?
You can use the Adobe Log Collector tool (Log Collector Tool) and share the corresponding zip file @ [email protected]
Thanks,
Shikha

How do I get fios to work with my new desktop w/ Windows Media Center

Can someone please help me I have "fios".TV and internet 1HDSTB + 1HDDVR with multi room dvr Home media mgr.how do I get fios to work with my new desktop HP Pavillion m9715f**(specs below)**w/ Windows Media Center or did I just throw away my money?
also equipted is 47" Samsung 850series 1080p 120hertz HD LCD TV + 36" Samsung 560series 1080p 60hertz HD LCD TV and 19"Samsung 950b LCD Monitor
** computer specs**
Product number NZ017AA
Introduction date 30-Jun-2009
Country/region sold in: United States,Canada
Hardware Base processor
Phenom-9650 (A) 2.3 GHz (95W) 3600 MHz HyperTransport 3.0 Socket, AM2+
Chipset AMD 780G
Motherboard Manufacturer: MSI Motherboard Name: MS-7548 HP/Compaq motherboard name: Aspen-GL8E
Power supply 300W
Memory
Component Attributes Memory Installed 8 GB Maximum allowed 16 GB (4 x 4 GB) (64-bit OS)
4 GB* (4 x 1 GB) (32-bit OS)
*Actual available memory may be less Speed supported PC2-6400 MB/sec Type 240 pin, DDR2
Hard drive750 GB SATA 3G (3.0 Gb/sec)7200 rpm
Blu-ray player & SuperMulti DVD burner with LightScribe Technology drive
This Blu-Ray Disc DVD drive introduces a player that reads Blu-ray Disc format enabling you to watch high-definition Blu-ray Disc movies. NOTE: This drive does not include high-definition write capability.
Formats/Disc types Write speeds Read speeds Storage capacity Blu-ray Disc BD-ROM SL NA up to 6X up to 25 GB BD-ROM DL NA up to 4.8X up to 50 GB BD-R SL not supported up to 6X up to 25 GB BD-R DL not supported up to 4.8X up to 50 GB BD-RE SL not supported up to 2.3X up to 25 GB BD-RE DL not supported up to 2X up to 50 GB HD DVD not supported DVD DVD-ROM SL NA up to 16X up to 4.7 GB DVD-ROM DL NA up to 8X up to 8.5 GB DVD+R SL up to 16X up to 12X up to 4.7 GB DVD+R DL up to 4X up to 8X up to 8.5 GB DVD+RW SL up to 8X up to 10X up to 4.7 GB DVD+RW DL not supported DVD-R SL up to 16X up to 12X up to 4.7 GB DVD-R DL up to 4X up to 8X up to 8.5 GB DVD-RW SL up to 6X up to 10X up to 4.7 GB DVD-RW DL not supported DVD-RAM up to 5X up to 5X up to 4.7 GB CD CDROM NA up to 40X up to 700 MB CDR up to 40X up to 40X up to 700 MB CDRW up to 24X up to 40X up to 700 MB CD-DA NA up to 32X up to 700 MB Video CD NA up to 10X up to 700 MB
Wireless Wireless LAN 802.11 b/g
Video Graphics Radeon HD4350
512 MB DDR2 memory
I/O Ports: HDMI, VGA, single-link DVI
Television Hauppauge ATSC/NTSC TV tuner card with FM tuner
Sound/Audio High Definition 8-channel audio
ALC 888S chipset
Network (LAN) Integrated 10/100/1000 Base-T networking interface
Memory card reader
Contains an Infrared receiver for remote control
Supports the following cards:
Compact Flash I
Compact Flash II
IBM Microdrive
Secure Digital (SD)
mini-SD
MultiMediaCard (MMC)
Reduced size MultiMediaCard (RS-MMC)
MultiMediaCard Plus (MMC plus)
MultiMediaCard Mobile (MMC mobile)
Memory Stick
Memory Stick Pro
Memory Stick Duo
Memory Stick Pro Duo
SmartMedia
xD Picture Card (xD = extreme digital)
External I/O ports
I/O ports on the front panel
Port type Quantity 15-in-1 (4 slot) with IR Receiver One USB Two Headphone One Microphone One Audio L-R One S-video in One Composite video in One
I/O ports on the back panel
Port type Quantity PS/2 (keyboard, mouse) Two S/PDIF out (coaxial) One VGA One (disabled due to the installation of a graphics card) DVI-D One USB Four 1394a One LAN One Audio (side speaker out, rear speaker out, center/subwoofer-out , line-in, line-out, microphone) One Each
Expansion slots
Slot type Quantity PCI Express x16 One (None available) PCI Express x1 Three (Two available)
Drive bays
Bay type Quantity 5.25" Two (One available) 3.5" Two (One available) Personal Media Drive One (One available) Pocket Media Drive One (One available)
Keyboard and mouse HP multimedia keyboard HP PS/2 optical mouse
Remote Control USB infrared remote control,Remote control expansion card with IR ports,IR emitter cable to transmit codes to a set top box

Based on what you've posted, your computer does not have the right tuner. You need a QAM tuner to record locals from FiOS, or a CableCard tuner to record all local and cable channels from FiOS.
QAM tuners to record local channels only
This requires Windows Vista or Windows 7
Hauppauge WinTV-HVR-2250
SiliconDust HDHomeRun (info on a sale)
CableCard tuner to record local and cable channels
This requires Windows 7 + one CableCard from Verizon for $3.99/mo
ATI TV Wonder Digital PC CableCard Tuner (records one channel at a time) -- $200-$250 on ebay
Ceton MOCUR tuner (records four channels at a time) -- coming in early 2010 for $400-$600
Make sure your computer has Windows 7 Home Premium (or better) installed. That's necessary to support CableCard tuners.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it.

Kichat: How do I get iChat 3 working ? Upgrade hints, FAQ

Disclaimer: Apple does not necessarily endorse any suggestions, solutions, or third-party software products that may be mentioned in the topic below. Apple encourages you to first seek a solution at Apple Support. The following links are provided as is, with no guarantee of the effectiveness or reliability of the information. Apple does not guarantee that these links will be maintained or functional at any given time. Use the information below at your own discretion.
How do I get iChat 3 working ? Upgrade hints:FAQ
Trouble Shooting Revisited
Ok We will start with loading Tiger and iChat version 3.0
From Panther
There are or were serveral Add-ons and applications avaiblable to Panther users of iChat that are not compatible with iChat 3.
These following need to be deleted.
iCAR - An Add-on that posts an Auto response Away message (produces a 1 fps result in a Video chat)
Virex for Panther - An Anti Virus app avialable to @mac account users (Produces the 1 fsp problem)
iChatUSBCam for Panther/iChat2.x - A Add-on utility for using iSight or USB cam with iChat2.x (Incompatible with Tiger/iChat 3)
iProfile - An Add-on for producing a profile on the AIM server that ichat 2.x could not do (not proven to be a problem but now not needed).
A clean install of Tiger (not Archive and Install) produces the best results.
But any install should also check these Tiger settings.
First, UPGRADE to 10.4.3 as this gets past many Connection issues that became apparent with the basic Tiger (10.4) and iChat 3.0 It updates iChat to version 3.1
Check Settings
Don't be complacent that you have not set anything different.
There are several new things in Tiger that may trip you up.
These are worth looking at:
Mac Firewall. Now includes the ability to Block all UDP traffic in the Advanced button (System Preferences > Sharing >Firewall tab then the Advanced Button).
Also can now open UDP protocol for ports where as the Panther one only did TCP (Check any old Panther settings you Added to the presets).
The ports should be:
TCP -5190
UDP -5060, 5190, 5678, 16384-16403
There are more ports for Bonjour 5297, 5298, 5353 UDP and 5298 TCP and Jabber, 5220, 5222, 5223 on TCP)
(Table View see 7th Sept)
QuickTime. This has a change in the name of the Connection Speed tab to Streaming (System Preferences > QuickTime) Check this is set to be equal to your connection speed (the download one if this is faster). See Apple Doc 301641 Dated 9th November 2005.
Date & Time. Not conclusively involved but worth eliminating. Set a Network Server and the correct Time Zone.
Apple Remote Desktop. If this is active in System Preferences > Sharing > Services tab it causes problems for iChat.
Next, test the actual speed you are getting from your ISP.
http://www.dslreports.com/stest
There is a table here of the speeds you need:
http://docs.info.apple.com/article.html?artnum=301050
The one you get linked to in the Help menu is wrong.
Other Known Problems
There are several other applications that iChat 3 does not seem to like.
folding@home This is a application that uses spare processor time to help find protein chains for a University.
PostgreSQL This is a data base application that can be reset to allow more processor time for iChat. See here http://www.murraywilliams.com/blog/archives/000046.html
Lotus Notes Some people have reported problems with this.
Make sure any Add-on Video cards or input PCI cards have up to date Firmware
IF you are still having problems I would do Routine Maintenance Tasks as laid out here.
Lastly, some routers/modems are SIP aware and give different results in iChat 3 compared to iChat 2.
This is due to the Operating System changing (like a new computer connecting to the modem) rather than iChat.
See My web pages: page4 at the SIP Text in a Box section.
Also for the above try some housekeeping particularly if you do not keep your Computer on 24/7 Gulliver, "kmosx3: Mac OS X 10.3/10.4: System maintenance"
Ralph
Do you want to provide feedback on this User Contributed Tip or contribute your own? If you have achieved Level 2 status, visit the User Tips Library Contributions forum for more information.

i think apple needs to keep up with the jones here, so far i read at LOGIC PRO FORUMS many saying cubase and pro tools left logic in the dust, 1 year ago already, sad, but true
in anycase, trye starting one app before the other to see which combination works., other wise i think more apps will fall out of sync with old logic pro

Get MTP to work on NWZ-E384

Similar Messages

Maybe you are looking for