Hard Drive Boundary

Is there an upper limit that Solaris 5 will see on a hard drive? My question comes from the fact that I installed a new unformatted 20gb seagate drive in an ultra 5 running solaris 5. When I enter format, the output shows only 8gb (7.7 something minus the buffer). Is there a patch I can install or anything I can do to enable the workstation to see the entire 20gb disk? I have some similar ultra-5's that are running 2.7 that dont have this issue.
Thanks
Mike

Hello Mike,
"Various releases of Solaris have different upper limits in the size of the IDE disks they support."
Please review the following link to the Solaris 2.x FAQ
http://www.science.uva.nl/pub/solaris/solaris2.html#q5.64
Michael

Similar Messages

  • NMH300 and hard drives with 4kB sectors size

    Hi
    Does anybody know if the NMH300 does support hard drives with 4kB sectors or only 512B size?
    If yes, how do HDs with 4k sectors perform?
    What I know: XP does not really like HDs with 4k sector size. W7 has no problems.
    Thank you for your feedback.
    Solved!
    Go to Solution.

    Sorry, I did not write why it is solved. First it just works with the NMH30x . Second to avoid increased access time due to a possible 4k sector misalignments  of older OS (like XP) pls read Western Digital's home page. Depending on the HD type you can set the advanced format jumper (check for your drive type: http://support.wdc.com/product/download.asp?groupid=608&lang=en) or download a SW which moves the first sector to a 4 k boundary. But not both should be done!
    Note: Windows 7 does not need this and for Linux it depends on the kernel version.
    Rgds

  • Beige G3 Hard Drive

    I recently purchased a Western Digital 80 gig drive (ide) for my 300 mhz beige G3. The 6 gig jyst wasn't cutting it! It intialized fine & I was able to rename it but now it won't show up anymore & says it's no longer supported. Any ideas/advice?
    Is there a certain brand/model of drive that will work better?
    Cheers on any feedback.

    First partition must be the UNDER 8 GB partition, so that the addresses of every block of that partition are under the 8 GB boundary. That is where you will install Mac OS X.
    The second partition can be the whole rest of the drive. This is where you should install OS 9.2, to be used as Classic and to boot directly for troubleshooting. The second partition will appear as a second Volume on the Desktop, as if you had two Hard Drives in your Mac. I recommend you do this before you attempt to install Mac OS X.
    Some users swear by having another small partition somewhere to hold a copy of their OS X files in case the original OS X image gets damaged. You cannot copy OS X with the Finder, because there are zillions of invisible files the Finder can't copy, but there are Utilities that can "clone" it back and forth to another partition -- "Carbon Copy Cloner" and "Super Duper" are well-regarded. There may be a small charge to download one or both of them.
    Be sure to choose HFS+ Extended, not plain HFS.

  • New Hard drive problems in G3 Imac

    Hey there. I went to Micro Center, and spoke to a "genius" who said I could put any EIDE HD in my blueberry Imac. I am now 1000 miles away from my house, at my sisters trying to upgrade her (my old) computer. I have installed the 160 gb hard drive, but the cd's won't boot. Can anyone help? I see now that there may be size requirements, but they womt take back an installed HD. I would really like to find a way to use it. I will need to fix this in the next day or so, since once I am in MI, it will be months before I am back. Any help is greatly appreciated.
    Happy Thanksgiving!

    did you set the harddrive to master? master is a must. cable select doesn't work. see the jumper settings on the drive.
    Did you check all of the cables? Put everything back and verify that all works.
    Do you have firewire? You can use target disk mode. Some people have claimed success when installing through target disk mode. Use your g4 to load the software onto the target disk.
    http://docs.info.apple.com/article.html?artnum=58583
    to boot from the cd, get the cd in the cd drive somehow. Power down the machine. Hold down the c key then poweron the machine.
    You can boot in startup mode on the slot loaders by holding down the option key when you poweron. This will give you a little more info. Click on what you want to boot the click on the right arrow.
    I am not certain what model of iMac you have. The tray loading iMac requires the boot partition to be within 8gig. Since there are hidden partition before the first visible partition, people recommend that you make the first visible partition 7.5 gig to 7.9gig. The machines support upto a 128gig Parallel ATA drive.
    You need to get the 3 and a 1/2 inch ATA harddrive. They are also known as parallel ATA or PATA. The iMac was designed to take a maximum drive size of 128gig. The 120gig drives are the largest readily available. People have put larger drives in the machine, but only 128gig is usable.
    I suggest you create a 127gig partition and leave the rest of the drive as free space. That way you will not have to worry about the boundary conditions.
    If you got firewire, you can get an external enclosure.
    Robert

  • Have Old Hard drive and want to move old data onto new hard drive in imac.

    I am trying to get my files off of an old hard drive. I have it hooked up through a sata drive. I am able to access all the programs but for whatever reason I am unable to access any of the files, i.e- 1,00's of pictures, videos, music, and documents. Is there something else I need to do in order to get the files, or is it possible that all the programs could still be on it but the files are just missing? In the current Sata it only has two plugs but on my hard drive it looks like there is another place to plug something in.

    Hello again Shadow,
    The way I do this is to:
    1) Install your new hard drive into your iBook
    2) Get your iBook reassembeled
    3) Place your old hard drive in your firewire enclosure
    4) Insert your install DVD into your iBook and restart with the C key held down. When the installer launches, select your language in the first pane, click 'continue' and in the upper dropdown menu in the next page select Utilities > Disk Utility. After DU is open, select your hard drive from the list of volumes on the left (the very top one), and then click the 'Partition' tab to the right. Then select 1 partition (normal) and make sure that you have 'Mac OS Extended (journled)' selected in the lower section. Then click 'partition'
    5)Quit disc utility, which brings you back to the installer. continue with your installation of OS X. In one of the first steps you will see a button on the lower left which says 'options' click on that and make sure that the option 'Installs OS X for the first time' is selected. It will normally be selected by default with a new drive.
    6) After the installation, the Migration Assistant will ask if you would like to transfer your information from another mac. click yes then follow the instructions. but instead of using another mac, connect a firewire cable from your enclosure with your old hard drive installed. The installer will think that this is another mac and will transfer all of your account information and user files (everything!)from your old drive to your iBook's new drive. Just diconnect when it says to and complete the installation sequence.
    You're done!
    Check back again if anything is unclear.
    Randy
    Message was edited by: DesertSage

  • I was given the wrong macbook when I gave mine in for repair.  I want to complain.  Also, they wiped ALL my data off the hard drive.  I want to complain to someone in authority.  How?

    I am extremely disappointed and angry with Apple service.  I am a writer and booked three weeks in Spain so that I could finish my book.  On the second day my laptop cut out on me asI was working on it, so I took it to Goldenmack in Cadiz.  Not only was I given someone else's macbook when I went back to collect it, but then when I returned to the UK, the Apple shop in Brighton managed to delete ALL my data from the hard drive because I was unlucky enough to get a trainee on her first day.  I have since learned she should not have deleted my data without even running a diagnostic.  She told me she was going to 'restore' the drive.  I took this to mean she was going to restore my work.  But no!  She erased the lot.
    I complained and eventually was put in touch with a supervisor, who I was told  had authority to resolve the issue. She said she would get the shop to phone me.  That was ten days ago and I'm still waiting. 
    Ok so there's nothing I can do now to get back the three chapters of my book that I have lost and didn't back up, but the  hard drive on this laptop is still faulty.  I try to back up my work every time I use the machine but as soon as I attach an external drive, the whole thing shuts down. I can't use it any more as I can't risk losing any more work.    This laptop is only just over a year old and this is just not acceptable, especially since I have really looked after it. 
    This is an appalling service I have encountered from Apple, and I am not going to ignore it.  I have contacted the young chap whose laptop I was erroneously given, and the repair of which I paid for! (although I did eventually get a refund),  to ask him if he had been given mine as well.  He said he had been completely unaware that his laptop had been given to me and he is furious as he had loads of "sensitive material" on it."  I have no idea in whose hands my laptop has been either, or indeed what damage it sustained while it was supposed to be in for repair.

    Contact Apple Support:
    http://www.apple.com/support/contact/
    Apple - How to Contact Us:
    http://www.apple.com/contact/
    Be sure to refer to the repair ticket number.
    Sounds like a terrible mixup.
    Good luck & happy computing!

  • Iomega external hard drive either 'not found' by Time Machine or is now in 'read only' format

    I don't know what's going on with my iomega external hard drive.  Sometimes the HD is recognised by the computer; other times it isn't; if it isn't I can restore to an earlier back up via Time Machine app; but it's like the disk isn't writable.
    Ten days ago, I had trouble backing up my iMac using Time Machine.  After turning it off and restarting my external hard drive, it backed up successfully.
    However, today I am trying to back up my files, and TM tells me it can't find the external hard drive.  Nothing has changed -- I have been out of town this past week -- but somehow my HD now seems to be in 'read only' format.  It does turn on, and I could restore my computer to an earlier back up.
    "Mac OS X can't repair the disk.  You can still open or copy files on the disk, but you can't save changes to files on the disk.  Back up the disk and reformat it as soon as you can."
    Annoyingly, despite my HD not showing in Finder or on my Desktop (as it usually does), when I simply turn it off I get that warning message "The disk was not ejected properly".
    Have tried verifying and repairing using Disk Utility, to no avail. 
    Am prompted to reformat but I don't have a good understanding of what this means and how to do it.  I'm guessing this would wipe the disk clean and I'd have to create the initial back up image all over again -- I'm reluctant to do this since this HD is my only back up and if it all goes tits up I'll be up that famous creek without a paddle.
    Thoughts, suggestions, input all welcome and deeply appreciated -- thank you!

    fzgy wrote:
    "Mac OS X can't repair the disk.  You can still open or copy files on the disk, but you can't save changes to files on the disk.  Back up the disk and reformat it as soon as you can."
    It's possible a heavy-duty 3rd-party disk repair app can fix it, but they're expensive (DiskWarrior is about $100), and there's no guarantee it can do it.
    Am prompted to reformat but I don't have a good understanding of what this means and how to do it.
    That will erase it.  See Time Machine - Frequently Asked Question #5.
    It sounds very much like the disk is beginning to fail, although it's possible there's a bad port, cable, connection or power supply (if it has its own).
    I'd suggest getting a new one, and using it for your Time Machine backups; once you have a good backup there, reformat the old one (and select Security Options to write zeros to the whole drive -- if that fails, you know the drive is toast).  Use it for secondary backups, per FAQ #27.   If it has failed, get a second new one for secondary backups. 

  • I need to upgrade my external hard drive, any suggestions

    I have an iMac i5 quad core (2010 model), I have been using a Seagate Barracuda 250 GB 7200 RPM from an older iMac 20" G5 in an OWC Mercury Elite Pro Firewire 400/USB 2.0/1.1 enclosure as my backup external HD.  The enclosure has the Oxford 911 chipset and says that it supports up to 750GB.
    Since I have been using Snow Leopard only I have used time machine to backup to this HD.  Now, that I have installed Lion, and partitioned my HD on my computer to have both Lion and Snow Leopard OS, I need to get a larger external HD to install in my OWC enclosure to save money.
    I was looking on the OWC website and found a SeaGate 2.0TB Barracuda Green SATA 6Gb/s 64MB, 5900 RPM for $90.00, or the 7200 RPM for $158.00.
    I am not sure if my enclosure with the Oxford 911 chipset will support this drive, and also the specs for my enclosure says up to 750GB, and that probably rules out these drives anyway.
    I could just keep what I have and use it as a back up of my Lion partition currently using 134 GB.  Snow Leopard using 127 GB on my internal 1TB hard drive.  Then, I could purchase the OWC Mercury Elite Pro 2.0 TB Firewire 400/USB 2.0/1.1 with the Oxford 934 chipset, 5900 RPM, and 64 MB for $150.00. Even thought this would be a little slower, is it worth paying $40.00 more for the 7200 RPM speed?
    On my hard drive now I am only using 261 GB, so after I first back up both partitions on the 2.0 TB external HD, any other backups would not take as long to do.  I have Super Duper, but right now it is not recognizing my Lion HD, and I have not backed up Lion to my current external HD yet since I want to get a larger external HD.  When I get the new HD, I can partition it so that I can backup either Lion partition or SL partition using time machine, it that right?  My current external HD is bootable, but I am confused about Carbon Copy or Super Duper, will that be saved on my external HD?
    Thanks,
    DaisyMay

    DaisyMay wrote:
    Firewire 400/USB 2.0/1.1
    I would recommend not settling for less then USB 3 or hold out for Thunderbolt, if your machine is capable. Firewire 800 minimum.
    MacBook Pro, Mac OS X (10.7), 2.4GHz IntelCore i5 320 HD 8GB RAM ParallelsDesktop6.0

  • How large of a hard drive can I install on dual G5, and do I need more RAM?

    I recently had a situation in which my dual-processor 2.0 G5 was completely refurbished by Apple repair-new logic board, both processors, video card, thermistor, all new. Finally it has been working well after a month of trips back and forth from the Apple store. I have two internal hard drives installed on my G5, both 300GB, one for OS applications, and one for audio. I am running out of space on my main hard drive, and so I recently purchased a Maxtor 1TB hard drive, now manufactured by Seagate, from Fry's. After having my G5 refurbished, I was having an issue with my Samsung 930B monitor going into sleep mode when I boot-up from a CD, but other than that G5 was working fine. I removed the main 300GB hard drive from slot #1 and put it into slot #2, from which I had removed my audio hard drive. I installed the Maxtor drive in slot #1 and reformatted it for Mac using my laptop with ATA/USB cables previously purchased for data transfer. This took about 14 hours as I used the "zeros" option. After that I hooked up the internal cables to both drives and tried to boot up from Leopard in order to install it on the Maxtor drive, but again my monitor went into to sleep mode. We went to the Apple store to try to see if there was an issue with the computer, but everything worked fine with their monitors and CD's, as well as my CD. So there is some kind of issue with my monitor, probably software as it works fine when booting up from the main hard drive, and also was fine when I did its self-test function. While at the Apple store, they installed Leopard from their hard drive which took about 30 minutes.
    My problem is this: When I arrived home, I turned on my G5, which had been set to boot from my new Maxtor drive and complete the Leopard setup process, which we had decided to do at home as it would have taken another 20 minutes in the Apple store. The G5 turned on, chimed, I got the Apple screen with the wheel, but then after that my monitor goes into sleep mode. I can hear Leopard's setup intro playing through the speakers, but the screen is in sleep mode. So I reboot holding down the option key so I can boot up from my old (300GB) main hard drive, now in slot #2. This works and the monitor screen does not go to sleep. However, as I am browsing on the web to check for issues concerning this monitor, the G5 freezes, and I get a screen with black bars with writing in them and various technical language across the screen. This happened several times after rebooting. Finally I shut the computer down. I am going to try removing the new hard drive and putting both old ones back in and see if the G5 stops crashing. I think the monitor issue is a separate issue, and I am more concerned with the crashing, as previous to the new hard drive installation the G5 was working fine, monitor fine, other than the issue when booting up from a CD. Do I need more memory? Is the 1TB hard drive too large for my dual-processor 2.0 G5 and overloading it? Would I be better off with a 500GB drive? Would appreciate advice from persons with experience in this area. Thank you.

    I have replaced my 5 year old G5 with a Mac Pro, as the G5 just had too many issues, even after replacing all major components (logic board, both processors, video card, etc.) Once I took out the 1 TB hard drive from my old G5, it stopped having the kernel panic issue. Nonetheless I had been through a lengthy repair process previous to this issue, so I didn't care to trust an older machine any longer, especially since being told by an Apple tech that the "new" parts were really just older parts stockpiled from a central location. Could be new, could be refurbished. Apple was kind enough to credit the money we had spent on the G5 repairs towards the purchase of my Mac Pro.

  • Back up using time machine and external hard drive

    Hello,
    I am having a difficult time deciding the best way to back up important documents. 
    I have:
    1TB internal hard drive
    3 TB external hard drive and
    1TB external hard drive
    I currently have about 1TB worth of data to be stored, but that will increase to about 1.5TB once I get a bunch of stuff off the HD camera's hard drive.  I would like to keep my internal hard drive somewhat free to keep the computer running fast, but also want to make sure I am properly backed up. 
    Should I put ALL (or nearly all) of the files on the 3 TB external hard drive, and have time machine back that up and not worry about the rest? I'm a little weary about putting all of the files on one device even if it is backed up by TM. 
    If I do this, do I need to back up the 3 TB external drive in addition to using TM?
    Thanks!

    iMac11,2
    OS X 10.6.8

  • I have formatted my SSD and hard drive.... I am running a clean install from disk of 8.1 pro. I cannot determine if it is a compatibility

    issue or hardware issue. I had run a memory test and scan disk for bad sectors from the bios. As administrator, I enabled automount  in diskpart to allow windows to assign a drive name. 
    From the bios, I can see both drives and only the ssd. I have not pinpointed when the harddisk is unmounted. It is formatted as NTFS. I can hear it unmount either during boot or upon waking from sleep mode. The bios sees no bad sectors nor does windows.
    However, when I had the intel compatibility software installed, my hard drive never mounted. I did a restart and inorder for windows to see my hard drive. I disabled the intel software for the 4th gen i7 processor. This problem is happening less often. I do
    not think I have solved the problem. Intel or Windows... I think a bit of both. 
    If there is a software patch, please guide me to it. I am in school and use my laptop ALL the time. I believe it is a compatibility issue. I have attached this from searching intel's site for downloads and windows is up to date. 
    I am quite concerned because I can hear my harddrive unmount. It is labeled as healthy NTFS partition. I have checked for hidden volumes and done everything I know to do to check the integrity of the hardware as administrator. I have searched microsofts
    libraries and forums and have done everything I can find as suggestions. 
    I have checked for malware, viruses, etc. My only clue this is going to happen is the hard disk spins up and I hear the fan, then I hear it unmount the drive. Of course, after unmounted there are other issues which I have ruled out as the cause of the problem.
    Basically, I am experiencing a lack of swap space after my hard drive unmounts.
    Any suggestions, are welcome! I would really like to know if this is a known windows issue. I should not have to disable intel's processor software. I paid for the features of the i7 and would like to utilise the processor.

    Hi,
    According to your descriptioin, I don't think this is system problem, it should be Intel driver problem. It would be contact Intel to confirm this issue whether this is their driver problem.
    Roger Lu
    TechNet Community Support

  • I moved iTunes music to my hard drive "D" and now it won't open!

    My hard drive "C" was getting somewhat full, so I decided to move my iTunes music files over to my second hard drive "D" (I have a dual hard drive on my computer). When I try and open iTunes, it says, "The folder 'iTunes' cannot be found or created, and is required. The default location for this folder is inside the 'Music' folder."
    I cannot open the "Music" folder, because when I do, it just opens up the same window I was already in when I tried to open it. The main reason I want to open iTunes is so I can reset my iPod because it is not working anymore. The scroll wheel, the hold button, the backlight, and it automatically sleep mode (after not touching it for a couple of minutes) is all that works. I cannot click anything.
    I have moved all of my iTunes folders back over to my "C" drive, but it still won't work. I also reinstalled iTunes in the "Music" folder, and it won't work. Basically nothing has worked!

    You might find this article useful, don't be put off by the title, the process is substantially similar moving to another internal drive: iLounge - Managing your iTunes Library on an External Hard Drive

  • How to restore playlists and ratings after hard drive format

    Several people have reported problems restoring paylists and ratings after reformating a hard drive. Here is what worked for me and what did not.
    I had to reformat my hard drive. Before doing that I exported my playlists from itunes to another hard drive as an xml file. I also copied the folder with all my songs to another drive. (Also of course had it backed up on DVDs.)Then I copied the itunes library files (see url http://docs.info.apple.com/article.html?artnum=93732) to anoher drive.
    After reformating my hard drive and installing the lastest verion of ITunes, I copied the actual songs back into a subfolder in my music folder. I then told iTunes to import the subfolder with the actual music. That resulted in a restored library that lacked playlists and ratings.
    Don't do this
    I purchased Anapod ($30.00) because its web page said (http://www.redchairsoftware.com/anapod/):
    "Anapod CopyGear is an easy-to-use, compact utility for copying music tracks, playlists, podcasts, photos, and videos from your iPod back to your PC."
    Well, I did transfer 104 playlists back to my iTunes library through the Anapod backup function. However, the transfer also put more than 20 gigs of duplicate songs into the library. All of the songs listed in the playlists were duplicated in iTunes. I could find no way in Anapod to simply copy the ratings and the playlists. Anapod documentation was outdated. For example the online help pages said that playlists could not be backed up. This was confusing because I had just done that.
    "In a future release we will be adding the ability to backup your iPod playlists. This will allow you to generate backup files of your iPod playlists on the computer. These files will not be usable on your computer though. They can only be used to restore playlists at a later time on your iPod (assuming it still carries all the audio files referred to in that playlist)." This text is from url http://www.redchairsoftware.com/anapod/support/tome/tx2pc.php#5.1.2
    I sent requests to Anapod for help today, but they have not been answered yet. Docs truly did not seem to help. Would have been good if there was a pdf file rather than just an online help html file that seemed outdated.
    This worked for me:
    I ended up having iTunes wipe out the entire library because of all the dups Anapod made. (Made sure that iTunes only wiped out library and did not delete actual songs from hard drive. Then I had iTunes import my subfolder with songs again. That brought me back to where I was before wasting money and much time on Anapod.
    After I had my iTunes library up (without ratings and playlists and after finding Anapod did not meet my needs.
    1. I imported the xml file to which I had exported playlists before reformating hard drive. That gave me the playlists back although an error message said some items not copied because the music tracks listed in playlists were not in my iTunes library. --Possibly I deleted songs after playlists were downloaded some time ago to iPod. Importing the xml file is probably not necessary because of what I did below.
    2. Quit iTunes
    3. Because my song ratings were still missing, I then moved the iTunes library files made by the new version of iTunes into a different folder.
    4. Then I put my old version 4 library files into the place where the library files should be.
    5. Then I crossed my fingers and restarted iTunes. It took awhile to start and said it was updating my library files. Now I have back most or all of my playlists and ratings.
    If problems develop, I will probably wipe out iTunes library and use Anapod to move everything from my iPod into a folder and tell iTunes to import that folder. That approach might avoid the dups that Anapod makes when restoring playlists to iTunes.
    So my message is keep your actual songs backed up somewhere (such as DVD's and anotehr hard drive) and keep a duplicate copy of your library files somewhere not on your hard drive. With these items you should be able to restore iTunes library to its former status.
    Sorry for the length of this message. Hope it helps someone.

    The simple version of above:
    iTunes Files to Backup (anytime you make additions or changes to the Music or Library that you want to retain)
    1) All music files in their current folder structure (usually located in and under the ‘iTunes Music’ folder)
    2) The Library database file: ‘iTunes Library.itl’ located in the ‘iTunes’ folder
    3) The Library XML file: ‘iTunes Music Library.xml’ located in the ‘iTunes’ folder
    4) Any XML playlist files created for Playlist retention
    5) The two iTunes.pref files (optional)
    -- C:\Documents and Settings\<your username>\Application Data\Apple Computer\iTunes\iTunes.pref
    -- C:\Documents and Settings\<your username>\Local Settings\Application Data\Apple Computer Inc\iTunes.pref
    6) The XML file of Ratings, Play Counts and Last Played attributes saved from the main Library and created by Otto’s SaveRatings script (also optional, but recommended):
    “Download this: http://ottodestruct.com/itunes/SaveRatings.zip . It's a program, just run it like any other program. Run it on the machine where you're copying the info from BEFORE you move the files to the new machine. Click the "Save Ratings" button and it'll create a ratings.xml file. Now when you move the files, move the program and this file as well. Then after you make your new iTunes library, run it again and click the "Restore Ratings" button. Voila, all your information is back in the Library. Well, most of it anyway, it's not perfect. It'll tell you what songs it couldn't figure out though, and there's usually not very many.”

  • Pavilon 500-319na can I install a second hard drive

    pavilon 500-319na second hard drive
    Options 
    ‎01-02-2015 09:30 AM
    Operating System: Windows 8.1
    I bought an HP Pavilion 500 - 319na desktop in summer and want to install a 2nd hard drive. There are spare connections on the board and the power cable to the internal hard drive has a spare connection. From what I read it needs to be SATA 3. I have read conflicting advice on this board.  Some say yes, some say no.
    OK, there seems to be only one bay (a poor oversight by HP) but provided I find a way of securing another drive is there any reason why it should not work.
    From what I read it should be max 2Tb's.
    I want a definitive answer please!
    Win 8.1 64 bit.
    This is the hard drive I plan to buy.  The spec says XP, Vista, Win 7, but am I right in thinking it should work with win 8.1 
    http://www.pcworld.co.uk/gbuk/components-upgrades/internal-hard-drives/3-5-inch-hard-drives/toshiba-...
    This question was solved.
    View Solution.

    As I said to you in the other cross posting (desktop hardware):
    You can obtain 3.5" hard drive cage from here for $11 shipped.  Granted it has a 120mm fan and space for 4 drives, but for the price, you can mod/cut all you want.
    Now your other issue/question:  You will want a SataIII 6GB/sec drive 2TB, 7200 RPM.
    I am a volunteer. I am not an HP employee.
    To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
    The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
    (2) HP DV7t i7 3160QM 2.3Ghz 8GB
    HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
    Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Both Customs use Rosewill Blackhawk case.
    Printer -- HP OfficeJet Pro 8600 Plus

  • Imminent hard drive failure message

    can i return my laptop to the store for a replacement.. it is less than 5 months old and i am getting an imminent hard drive failure message. totally unacceptable

    HP will replace the hard drive under warranty. Not too many stores will permit a return after 5 mos. We can also assist with a hard drive replacement.

Maybe you are looking for