Heaviest Weight paper that can be used to Print on

HP Officejet Pro 8600 e-All-in-One Printer - N911a: I normally use Ink Jet Paper that is 24 pound weight.
My Question is: What is the heaviest weight paper that this printer can handle?
We need to use a heavier weight paper for divider tabs.
Thanks, Bob
This question was solved.
View Solution.

It looks like 90-110 is the highest based on the specifications. Dividers should be far below this, so it should work out fine.
Media weight, recommended 16 to 28 lb (plain paper); 60 to 75 lb (photo); 20 to 24 lb (envelope); 90 to 110 lb (card)
Jon-W
I work on behalf of HP
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
Click the KUDOS STAR on the left to say “Thanks” for helping!

Similar Messages

System Image Restore Fails "No disk that can be used for recovering the system disk can be found"

Greetings
                                    - Our critical server image backup Fails on one
server -
Two 2008 R2 servers. Both do a nightly "Windows Server Backup" of Bare Metal Recovery, System State, C:, System Reserved partition, to another storage hard drive on the same machine as the source. Active Directory is on the C: The much larger D: data
partition on each source hard drive is not included.
Test recovery by disconnecting 500G System drive, booting from 2008R2 Install DVD, recovering to a new 500G SATA hard drive.
Server A good.
Server B fails. It finds the backed-up image, & then we can select the date we want. As soon as the image restore is beginning and the timeline appears, it bombs with "The system image restore failed. No disk that can be used for recovering the system
disk can be found." There is a wordy Details message but none of it seems relevant (we are not using USB etc).
At some point after this, in one (or two?) of the scenarios below, (I forget exactly where) we also got :
"The system image restore failed. (0x80042403)"
The destination drive is Not "Excluded".
Used   diskpart clean   to remove volumes from destination drive. Recovery still errored.
Tried a second restore-to drive, same make/model Seagate ST3500418AS, fails.
Tried the earliest dated B image rather than the most recent, fail.
The Server B backups show as "Success" each night.
Copied image from B to the same storage drive on A where the A backup image is kept, and used the A hardware to attempt restore. Now only the latest backup date is available (as would occur normally if we had originally saved the backup to a network location).
Restore still fails.         It looks like its to do with the image rather than with the hardware.
Tried unticking "automatically check and update disk error info", still fail.
Server A SRP 100MB C: 50.6GB on Seagate ST3500418AS 465.76GB Microsoft driver 6.1.7600.16385   write cache off
Server B SRP 100MB C: 102GB on Seagate ST3500418AS 465.76GB Microsoft driver 6.1.7600.16385   write cache off
Restore-to hard drive is also Seagate ST3500418AS.
http://social.answers.microsoft.com/Forums/en-US/w7repair/thread/e855ee43-186d-4200-a032-23d214d3d524      Some people report success after diskpart clean, but not us.
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/31595afd-396f-4084-b5fc-f80b6f40dbeb
"If your destination disk has a lower capacity than the source disk, you need to go into the disk manager and shrink each partition on the source disk before restoring." Doesnt apply here.
http://benchmarkreviews.com/index.php?option=com_content&task=view&id=439&Itemid=38&limit=1&limitstart=4
for 0x80042403 says "The solution is really quite simple: the destination drive is of a lower capacity than the image's source drive." I cant see that here.
Thank you so much.

Hello,
1. While recovering the OS to the new Hard disk, please don't keep the original boot disk attached to the System. There is a Disk signature for each hard disk. The signature will collide if the original boot disk signature is assigned to the new disk.
You may attach the older disk after recovering the OS. If you want to recover data to the older disk then they should be attached as they were during backup.
2. Make sure that the new boot disk is attached as the First Boot disk in hardware (IDE/SATA port 0/master) and is the first disk in boot order priority.
3. In Windows Recovery Env (WinRE) check the Boot disk using: Cmd prompt -> Diskpart.exe -> Select Disk = System. This will show the disk where OS restore will be attempted. If the disk is different than the intended 2 TB disk then swap the disks in
correct order in the hardware.
4. Please make sure that the OS is always recovered to the System disk. (Due to an issue: BMR might recover the OS to some other disk if System disk is small in size. Here the OS won't boot. If you belive this is the case, then you should attach the
bigger sized disk as System disk and/or exclude other disks from recovery). Disk exclusion is provided in System Image Restore/Complete PC Restore UI/cmdline.
5. Make sure that Number and Size of disks during restore match the backup config. Apart from boot volumes, some other volumes are also considered critical if there are services/roles installed on them. These disks will be marked critical for recovery and
should be present with minimum size requirement.
6. Some other requirements are discussed in following newsgroup threads:
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/871a0216-fbaf-4a0c-83aa-1e02ae90dbe4
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/9a082b90-bd7c-46f8-9eb3-9581f9d5efdd
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/11d8c552-a841-49ac-ab2e-445e6f95e704
Regards,
Vikas Ranjan [MSFT]
------- This information is provided as-is without any warranties, implicit or explicit.-------

Is there a limit to no. of summary fields that can be used in a cross tab?

Hi,
While creating a cross tab is there a limitation to number of summarized fields that can be used?
- The cross tab when uses 184 fields as summary fields leads to Crystal report application to crash at the time of export to excel.
- Tried with two Datasources: XML and excel
- If we reduce the number of summary fields used to 102 exactly, export works fine in excel.
- If 2 cross tabs are used each containing 92 summary fields(in order to show 184) export to excel works fine.
Please let me know if there is any such limitation which leads to CR application to crash when exporting in excel?
Thanks
Regards,
Nidhi

I suggest you purchase a case and have a dedicated support engineer work with you directly:
http://www.sdn.sap.com/irj/boc/gettingstarted
Or
http://store.businessobjects.com/store/bobjects/Content/pbPage.CSC_map_countyselector/pgm.67024400?resid=jFmmLgoBAlcAAALO-iYAAAAP&rests=1278687224728
If this is a bug you'll get a refund, if not post your enhancement request in the Idea Place. Or the Rep will suggest a better way to create your report.

When I sync my iphone 4S using iTunes it only syncs 8.5GB of music, not the entore library as specified. Is there a capcity default limit of the amount of storage that can be used for music and if so how do I change it?

When I sync my iphone 4S using iTunes it only syncs 8.5GB of music, not the entore library as specified. Is there a capcity default limit of the amount of storage that can be used for music and if so how do I change it?

The only limit is that of the device. No restrictions on how much of it you can use for music. Is part of your music library unchecked?
tt2

What format i should use for my external hard drive that can be used interchangeably between mac and pc?

What format i should use for my external hard drive that can be used interchangeably between mac and pc?

Usually Fat32/MS-DOS as mentioned, but that has several limitatiuns, like 4GB filesize limit.
One option is MacDrive for you PCs... allows them to Read/Write HFS+...
http://www.mediafour.com/products/macdrive/
More options...
NTFS-3G Stable Read/Write Driver...
http://www.ntfs-3g.org/
MacFUSE: Full Read-Write NTFS for Mac OS X, Among Others...
http://www.osnews.com/story/16930

Is there any way to an index that can be used to include the "OR condition "?

Hello I have some questions.
The test was conducted in the following procedure .
create table test
c1 varchar2(10),
c2 varchar2(10),
primary key(c1)
create index test_idx1 on test(c2);
Command> explain select * from test where c1 = 'AAAAAAAAAA' or c2 = 'AAAAAAAAAA';
Query Optimizer Plan:
STEP:                1
LEVEL:               1
OPERATION:           RowLkRangeScan
TBLNAME:             TEST
IXNAME:              TEST
INDEXED CONDITION:   <NULL>
NOT INDEXED:         TEST.C2 = 'AAAAAAAAAA' OR TEST.C1 = 'AAAAAAAAAA'
Command>
Command> explain select * from test where c1 = 'AAAAAAAAAA' and c2 = 'AAAAAAAAAA'
Query Optimizer Plan:
STEP:                1
LEVEL:               1
OPERATION:           RowLkRangeScan
TBLNAME:             TEST
IXNAME:              TEST
INDEXED CONDITION:   TEST.C1 = 'AAAAAAAAAA'
NOT INDEXED:         TEST.C2 = 'AAAAAAAAAA'
Command>
By including the "OR condition " in this test does not use the index.
Is there any way to an index that can be used to include the "OR condition "?
Thanks.
GooGyum.

A database cannot in general use indexes in this way for an 'or' involving two different columns. However, for this specific example one can easily rewrite the query using 'UNION' to use the relevant indexes while still giving the same (correct) result:
Command> explain select * from test t1 where t1.c1 = 'AAAAAAAAAA' union select * from test t2 where t2.c2 = 'AAAAAAAAAA';
Query Optimizer Plan:
STEP:                1
LEVEL:               1
OPERATION:           RowLkRangeScan
TBLNAME:             TEST
IXNAME:              TEST
INDEXED CONDITION:   T1.C1 = 'AAAAAAAAAA'
NOT INDEXED:         <NULL>
STEP:                2
LEVEL:               2
OPERATION:           RowLkRangeScan
TBLNAME:             TEST
IXNAME:              TEST_IDX2
INDEXED CONDITION:   T2.C2 = 'AAAAAAAAAA'
NOT INDEXED:         <NULL>
STEP:                3
LEVEL:               1
OPERATION:           OrderBy
TBLNAME:             <NULL>
IXNAME:              <NULL>
INDEXED CONDITION:   <NULL>
NOT INDEXED:         <NULL>
STEP:                4
LEVEL:               2
OPERATION:           UnionMergeSort
TBLNAME:             <NULL>
IXNAME:              <NULL>
INDEXED CONDITION:   <NULL>
NOT INDEXED:         <NULL>
Maybe you can apply a similar trick? If you know there is no possibility of duplicate rows then you can further optimise this (in terms of performance) by using UNION ALL.
Chris

Is there a list of Unicode characters that can be used in Acrobat bookmarks?

I can add Greek characters to Acrobat bookmarks using hexadecimal strings. For example, to print a lower case gamma symbol I use <FEFF03B3>. FEFF is the required Unicode flag and 03B3 is the Unicode code for gamma. This works fine. However, there are no Unicode entries for greek characters in the PDF 32000-1:2008 PDF Specification manual. Table D.2 - PDFDocEncoding Character Set on page 656 lists Unicode characters and these also work when added to bookmarks but no Greek codes are in this table. Since I can sucessfully use Greek Unicode characters in the range of 0x0391 - 0x03CE and these characters are not listed in the PDF manual I am assuming there are additional Unicode character that will work in bookmarks. Therefore, I am looking for a complete list of Unicode characters that can be used in Acrobat's bookmarks. Does such a list exist?

Thank you for the response.
I'm sorry to hear there is no list available. I'm building the Acrobat bookmarks automatically. The input data contains entity codings (for example, a lower case Greek gamma is coded as γ) and I was hoping to be able to just pass these through with an automatic conversion to a hexadecimal string (for example <FEFF03B3>). If I had a list of valid Unicode characters, that will display in an Acrobat bookmark, I could validate each entity before the conversion and catch the ones that won't display correctly. I know these types of characters are out there because I have already come across them. For example, a superscript 5 (0x2075) displays fine in MSWord but shows as a white box in a bookmark. Now I'll need to proof the output PDFs and look for white boxes in the bookmarks so that I can build my list of unicode characters that do not work in Acrobat bookmarks.
Again, thanks for your help.

Need to know of a method / process that can be used to send the same msg to all those appearing in my email listings with the same extension after the "@" sign in their address(es) on my macbook [e.g., with "@gov.ca"; Snow Leopard].

Need to know of a method / process that can be used to send the same msg to all those appearing in my email listings with the same extension after the "@" sign in their address(es) on my macbook [Snow Leopard].

If you simply want to send the exact same message to everyone in your address book with emails ending in "@whatever.com", you can do the following:
Create an email with subject, message and attachments but no addresses
Open Address Book, All Contacts
Search in Address Book for @whatever.com
Select the results and drag them into the To: or Bcc: field of the email. If Bcc: then put your email address in the To: field.
Send the email
This will not personalize the emails (such as with "Dear firstname:" at the top of the message) but it will let you send an idential message to everyone who meets your criteria.

Has anyone tried to trade in the their iphone5 for the gift card that can be used to buy iphone6?

Has anyone tried to trade in the their iphone5 for the gift card that can be used to buy iphone6?

csa3, I want to make sure you are able to take advantage of this offer. Have you submitted a Preorder for the iPhone 6? If so, you can submit your appraisal before September 30, 2014 using the following link: http://bit.ly/GGnDDC
AndreaS_VZW
Follow us on Twitter @VZWSupport

Third party reporting tools that can be used with WLI 8.1

All:
I am working on Weblogic Integration 8.1. I am wondering are there any ready tools that can be used with WebLogic Integration process related tables to get different types of reports out of it.
Can somebody point me to these tools??
TIA,
Prashanth Bhat.

Are you using ADE to read bought books, library books, or only free books?
If only free books, I suggest you install the superior free Calibre instead (http://calibre-ebook.com/)
For bought or library books you do need to install ADE on the new machine.
You will also need to register it with your Adobe ID; the same one you used on the last machine.
If you can't remember that ID or the password, ask, and we may be able to help.
I will give instructions for the latest version of ADE (2.0.1), even though I am afraid it has more problems than the old one it is more 'standard'.
Goto http://www.adobe.com/uk/products/digital-editions/download.html
Click on the 'Download Digital Edition 2.0.1 Windows (5.6 MB)' (you can go direct to http://download.adobe.com/pub/adobe/digitaleditions/ADE_2.0_Installer.exe if you prefer)
When it has downloaded you must open/run it. If you are using Internet Explorer, choose the Run option when you start the download.
It should now go through a fairly standard install procedure, asking if it is ok to run the program, etc etc
Take the easy 'yes' or equivalent option at each step.
When it is safely installed, run it. It should have put an icon on the desktop.
You now need to authorize ADE.
Use ctrl-shift-U which will open up a dialog asking for your Adobe ID and password.
You should now be able to use it pretty much as you used ADE on your old machine.
Good luck. Unfortunately not a very easy process even when all works well, and there are several things that can go wrong.
Don't hesitate to ask again if you need help.

Number of elements that can be used with 'in' Operator

One of my SQL query having 'in' operator failed saying number of elements exceed.
Is there a limit on number of elements that can be used with - 'in' operator.
And if yes can it be increased?

Parag Kalra wrote:
One of my SQL query having 'in' operator failed saying number of elements exceed.
Is there a limit on number of elements that can be used with - 'in' operator.
And if yes can it be increased?You cannot have more than 1000 literals in an IN clause.
Please check
ORA-01795, limit on in clause
Max number of values in IN clause
Edited by: Rajesh Lathwal on May 24, 2010 12:28 PM

What component is included with Microsoft SQL Servers that can be used to perform a broad range of data migration tasks?

What component is included with Microsoft SQL Servers that can be used to perform a broad range of data migration tasks?
a. Full Text Search service
b. SQL Notification Server
c. SQL Reporting Server
d. SQL Server Integration Services

d.
Are you having a test and trying to cheat?
For every expert, there is an equal and opposite expert. - Becker's Law
My blog
My TechNet articles

To offer integrated forms, so like Jotform, there are templates that can be used and upload options to FTP client as well as other built in widgets.

To offer integrated forms, so like Jotform, there are templates that can be used and upload options to FTP client as well as other built in widgets.

What you need is merged help.
You generate a parent and all the child projects. You always install the parent and then whichever child projects you require. The TOC, search and index automatically adjust. See the pages on my site.
Note though that many people take another view to your Product Development. Show all the help and then people see information about something and realise they need it!
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge

Example of creating ALV double click event that can be used in ANY Program

Once you get the hang of OO you can really create useful generalized code that can be used in a huge number of situtations.
Double click on ALV is often wanted
Right here goes to implement a generalized double click action that returns the row, column and column name back to the caller.
In your CLASS in the DEFINITION part code as follows.
CLASS zcl_dog DEFINITION.
PUBLIC SECTION.
METHODS:
constructor
      IMPORTING       z_object type ref to zcl_dog,
                     i_parent     type ref to cl_gui_custom_container,
PRIVATE SECTION.
on_dubbelklik FOR EVENT double_click OF cl_gui_alv_grid
      IMPORTING e_row
                e_column
                es_row_no,
dubbleklik
      IMPORTING
                 e_row type LVC_S_ROW
                 e_column   TYPE LVC_S_COL
                 es_row_no type lvc_s_ROID
                 program type sy-repid.
code here any extra any methods you need.
In the CONSTRUCTOR method of the implementation
CLASS zcl_dog IMPLEMENTATION.
METHOD constructor.
   CREATE OBJECT grid_container1
       EXPORTING
               container_name = 'CCONTAINER1'.
    CREATE OBJECT grid1
        EXPORTING
              i_parent = grid_container1.
    SET HANDLER z_object->on_user_command for grid1.
    SET HANDLER z_object->on_toolbar for grid1.
    SET HANDLER Z_OBJECT->handle_data_changed_finished FOR grid1.
    SET HANDLER Z_OBJECT->on_dubbelklik FOR grid1.
endmethod.
METHOD on_dubbelklik.
CALL METHOD me->dubbleklik
exporting
                 e_row = e_row
                 e_column = e_column
                 es_row_no = es_row_no
                 program = sy-repid.
break-point 1.
method dubbleklik.
perform dubbleklik IN PROGRAM (program)
    using
    e_row
    e_column
    es_row_no.
ENDMETHOD.
endclass.
This will now perform a routine called dubbleklik in your application program whenever you double click a cell in the grid.
In the application program just code the following
DATA: z_object type ref to zcl_dog, "Instantiate our class
       grid_container1 type ref to cl_gui_custom_container,
CREATE OBJECT z_object EXPORTING z_object = z_object.
call ANY method in the class which eventually displays the grid
CALL METHOD z_object->build_dynamic_structures
        CHANGING it_fldcat = it_fldcat.
form dubbleklik using
        e_row   type LVC_S_ROW
        e_column type LVC_S_col
        es_row_no type lvc_s_roid.
break-point 1.
endform.
When you double click a cell you'should be at the break point in your routine in the application program.
You've got the cell that was clicked so by reading your table you can examine the data and take the appropriate action.
Cheers
Jimbo

I suggest you purchase a case and have a dedicated support engineer work with you directly:
http://www.sdn.sap.com/irj/boc/gettingstarted
Or
http://store.businessobjects.com/store/bobjects/Content/pbPage.CSC_map_countyselector/pgm.67024400?resid=jFmmLgoBAlcAAALO-iYAAAAP&rests=1278687224728
If this is a bug you'll get a refund, if not post your enhancement request in the Idea Place. Or the Rep will suggest a better way to create your report.

What is the most advanced version of ACR that can be used with Photoshop CS5?

What is the most advanced version of ACR that can be used with Photoshop CS5?
Will it open RAW files from a Canon 5D Mark III ?

CS5 can use up to ACR 6.7.1. CS6 started with ACR 7.0.
The 5D Mark III was first supported with ACR 6.7.
ACR 6.7.1 can be downloaded from the Camera Raw Mac and Win links on the Adobe Download page:
http://www.adobe.com/downloads/updates.html
References:
http://helpx.adobe.com/x-productkb/global/camera-raw-compatible-applications.html
http://helpx.adobe.com/creative-suite/kb/camera-raw-plug-supported-cameras.html

Heaviest Weight paper that can be used to Print on

Similar Messages

Maybe you are looking for