Hello, I have a problem 4th with my iPod touch

Hello,
I have a problem 4th with my iPod touch
I just wanted to edit a picture, and then he is always crashed.
Hope someone can tell me what to do.
THX, Soundwave1409

First, try a system reset.  It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore, go into Recovery Mode per the instructions here.

Similar Messages

  • Hello I have just purchased a 2nd hand Ipod touch 4th Gen, I cannot seem to delete the Apple ID in the message settings of the previous owner?

    Hello I have just purchased a 2nd hand Ipod touch 4th Gen, I cannot seem to delete the Apple ID in the message settings of the previous owner?

    Go to Settings>General>Reset>Erase all Content and Settings. Then setup the iPod with your account.
    If necessary, place the iOS device in Recovery Mode if necessary to allow the restore.
    If recovery mode does not work try DFU mode.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    For how to restore:
    iTunes: Restoring iOS software

  • I have a problem updating the new ipod touch 5th generation

    I have a problem updating the new ipod touch 5th generation and I need help:
    With each attempt I receive the message:
    iTunes has detected an iPod in recovery mode.  You must restore this iPod before it can be used with iTunes.
    The iPod only displays a USB cable with an arrow pointing to an iTunes logo.
    I receive a "Are you sure..." message with the 2 options, one to Restore and Update and the other to Cancel.
    Each time I have selected the Restore and Update button and then moved through the acceptance screens.  Then iTunes begins to download the iOS 6.0.1 Software Update, which usually takes about 50 minutes.  During the download I will receive messages that an iPod has been found in restore mode.
    After the download is complete no update occurs to the iPod and iTunes displays the Device Summary screen showing derive Name as iPod and all other items as n/a.
    The iPod was working great without any known issues prior to attempting to update the OS.

    Maybe:
    iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
    Unable to contact the iOS software update server gs.apple.com
    Error 1004, 1013, 1638, 3194: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors:
    Install the latest version of iTunes.
    Check security software. Ensure that communication to gs.apple.com is allowed. Follow this article for assistance with security software. iTunes for Windows: Troubleshooting security software issues.
    Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. Follow iTunes: Advanced iTunes Store troubleshooting to edit the hosts file or revert to a default hosts file. See section "Blocked by configuration: (Mac OS X/Windows) > Rebuild network information".
    Try to restore from another known-good computer and network.
    If the errors persist on another computer, the device may need service.

  • Hello- I use a radio app with my iPod touch 5, when I plug it in to my JBL dock speaker, it shuts down after about 10 minutes. Can I defeat this auto shut off mode ? thanks -

    Hello- I use a radio app with my iPod touch 5, when I plug it in to my JBL dock speaker, it shuts down after about 10 minutes. Can I defeat this auto shut off mode ? thanks -

    Al that is left are the standard fixes:
    - Reset the dock
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up                             
    - Restore to factory settings/new iOS device.

  • HT1449 i have bought a new iPod touch and when i went to sync my iTunes library most of the songs didn't come across they get a explanation mark at the side they are whole cds of music. but i didn't have this problem on my old ipod touch when i was using

    I have bought a new ipod touch and when i went to sync my music library on to it only a few songs went over, the ones that didnt had a ! next to them. I had no problem when using my last ipod touch but i was using a pc at the time not a mac though.

    Hi there,
    This usually meas that iTunes can't find the original files. I would recommend taking a look at the article below for some tips on locating that lost media.
    iTunes: Finding lost media and downloads
    http://support.apple.com/kb/ts1408
    -Griff W.

  • Cannot seem to get a signal from my router with my Ipod touch. Lap top and desk top are working fine.

    I have been having trouble with my Ipod touch getting a signal from my 2wire router. This is an easy set up for lap top and desk top. Now I can't seem to get the internet with my ipod. I can get the a signal with my wife's ipod 3rd generation with no problems.  My old ipod i purchased in early 07. I can get a signal at the local McDonalds or Starbucks. Just not at home. Does anyone else have this problem? I ran the reset as prescribed by apple but have been unsuccessful.

    The problem is most likely with your router.  Follow the instructions in the router's manual to reset it.  Also what security are you using?  If it's WEP upgrade to WPA.  The iPod sometimes has trouble with WEP "protected" routers.  I put "protected" in quotation marks because WEP security is essentially useless.  It can be hacked in less that 30 seconds.

  • HT204380 Hello...i have one problem with my ipod touch 4th gen....when i try to log in and start use the facetime one message appears in the screen that is say....you couldn't get log into facetime...what i must do??pleaze help me :/

    Hello i have one problem with my ipod touch 4th gen....when i try to log in facetime one message appears in the screen whick saying you couldn't log into facetime.....what i suppose to do?? :/please help me :/

    Try:
    The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems

  • Hello  I have a problem with Mac Pro, iPhoto does not want to stay open and close as I can figure this out?  thanks

    Hello  I have a problem with Mac Pro, iPhoto does not want to stay open and close as I can figure this out?  thanks

    Refer below link once
    App doesn’t open | Progress wheel spins continually

  • Hello, I have a problem with the iPod, is that the iPod does not sync all the songs that are on my Itunes. I have 373 songs on the iPod and iTunes 512 in ... What do I do?

    Hello,i have a problem with the Ipod,is that the Ipod doesn't sync all the songs in my Itunes. I have 373 songs in my Ipod and 512 sons in my Itunes. What do i do?

    Hello,
    I take it you haven't unticked any of the songs listed on your iTunes Library? Also have you tried selecting all your songs which you wish to add to your iPod, and dragging them over your Devices "iPod Nano"; and seeing if that copies all songs on to your iPod?
    Another idea is just check that your iPod has enough space for the rest of your songs to be added to your device.
    Hope this helps.

  • Hello, I have a problem with my mac book pro after running the battery dead on a game.  The display has shrunk leaving two black margins on either side. What to do ?

    Hello, I have a problem with my mac book pro after running the battery dead on a game.  The display has shrunk leaving two black margins on either side. What to do ?

    Go to System Preferences>Displays and set the resolution to "Best for this computer" (or something to that effect).
    Clinton

  • Hello I have a problem with a Wifi Survey app, this app is from Access Agility, however this app was working fine, but without advise stop of working, I tried to open again, but app be close after few seconds.

    Hello I have a problem with a Wifi Survey app, this app is from Access Agility, however this app was working fine, but without advise stop of working, I tried to open again, but app be close after few seconds. Every time that I tried to open it, in diagnostic and use create some files, in special one named LatestCrash-WifiSurvey.plist, this one generate an incident identifier E73B0164-CDFA-4E9E-839E-A0C021BD17A2, but this incident identifier change every time that I tried to open, the last incident identifier is: DE600EB3-AB57-4C33-8DE8-71F6788A7441.
    After of it, I checked that the app had a new version available for downloading, I took a backup of my ipad and then upgrade this app, but is the same problem, all I want is to save the projects I had in this app, I´m afraid that if I delete this app and re-install it, probably I loss my projects.
    Thanks for your help indicating how I can save my projects and see them for example in an iphone for assurance that data is not lost.
    Something that called my attention is part of the log that shows a big CPU processing, but the strange thing is I killed all applications.
    Incident Identifier: E73B0164-CDFA-4E9E-839E-A0C021BD17A2
    CrashReporter Key:   ed0ca1405ce83d4f80cb3cce063d7248d7b76e91
    Hardware Model:      iPad2,5
    Process:         WifiSurvey [139]
    Path:            /var/mobile/Applications/1BEEE35A-85FC-4BE4-B62A-39A930CB3CE2/WifiSurvey.app/Wi fiSurvey
    Identifier:      WifiSurvey
    Version:         ??? (???)
    Code Type:       ARM (Native)
    Parent Process:  launchd [1]
    Date/Time:       2013-08-08 19:01:13.476 -0500
    OS Version:      iOS 6.1.3 (10B329)
    Report Version:  104
    Exception Type:  00000020
    Exception Codes: 0x000000008badf00d
    Highlighted Thread:  0
    Application Specific Information:
    com.accessagility.wifisurvey failed to launch in time
    Elapsed total CPU time (seconds): 20.990 (user 20.990, system 0.000), 52% CPU
    Elapsed application CPU time (seconds): 19.954, 50% CPU

    See:
    iOS: Troubleshooting applications purchased from the App Store
    Contact the developer/go to their support site if only one app.
    Restore from backup. See:
    iOS: How to back up              
    Restore to factory settings/new iPod

  • Hello I have a problem with my ipod touch 1G the problem is that see me key to the floor! And when recogi not prendia after 5 minutes prendio but it gave to me the surprise of which the battery had finished completely! What I did was to set it to load wit

    Hello I have a problem with my ipod touch 1G the problem is that see me key to the floor! And when recogi not prendia after 5 minutes prendio but it gave to me the surprise of which the battery had finished completely! What I did was to set it to load with the USB but do not load the battery me the icon of the battery appear and below of her the beam that indicates that this being loaded but this way I have left it the whole yesterday and what goes of today and continues without loading anything! They can help me porfavor I am grateful for them to him very much!   And my PC does not detect it not itunes

    Try the not-charging topic of:
    iPod touch: Hardware troubleshooting
    It could be that the battery is dead.

  • Hello, I have this problem on updating applications on my iPhone 4s 5.1.1 i dont know if you can help me with. when ever i want to update an application on apple store i get a different user name then mine(slamdance@cracked.by) this user name is not mine

    Hello,
    I have this problem on updating applications on my iPhone 4s 5.1.1 (jail broken) i dont know if you can help me with.
    when ever i want to update an application on apple store i get a different user name then mine([email protected]) this user name is not mine but its always there only on updating my app's.
    thanking you in advance for your kind help.

    Under the Terms of Use of this forum it is prohibited to discuss jail breaking. By jail breaking your iPhone you void any warranty you may have and forfeit any support from this forum.

  • Hello, I have a Mac computer with NVIDIA 750M dedicated graphics card and monitor EIZO but the problem was there when I was working with Windows and Acer monitor. When I open a file from Camera Raw in PS this is smaller than the screen so I double-click w

    Hello, I have a Mac computer with NVIDIA 750M dedicated graphics card and monitor EIZO but the problem was there when I was working with Windows and Acer monitor. When I open a file from Camera Raw in PS this is smaller than the screen so I double-click with the tool "hand" to fit on the screen, but the picture loses sharpness and becomes blurry. If you magnify the image even only slightly with the tool "zoom" the picture comes back clear. In Camera Raw instead is always sharp. I solve the problem by turning off the graphics card in PS but often use plugin that need the graphics card otherwise the processing time is much longer. I ask for help.
    Thanks.

    Hello, I have a Mac computer with NVIDIA 750M dedicated graphics card and monitor EIZO but the problem was there when I was working with Windows and Acer monitor. When I open a file from Camera Raw in PS this is smaller than the screen so I double-click with the tool "hand" to fit on the screen, but the picture loses sharpness and becomes blurry. If you magnify the image even only slightly with the tool "zoom" the picture comes back clear. In Camera Raw instead is always sharp. I solve the problem by turning off the graphics card in PS but often use plugin that need the graphics card otherwise the processing time is much longer. I ask for help.
    Thanks.

  • Hello I have a problem to update Imovie. I want to update but I get "There is a billing problem with a previous purchase" What do I do?

    Hello I have a problem to update Imovie. I want to update but I get "There is a billing problem with a previous purchase" What do I do?

    Restore from iTune Backup
    1. Settings>General>Reset>Erase all content and settings
    2. You will be asked twice if you want to erase iPad
    3. Slide to set up
    4. Select Language
    5. Select Country
    6. Enable Location Service
    7. Choose Wi-Fi Network
    8. Enter Wi-Fi password
    9. (a) Setup as new (b) Restore from iCloud Backup (c) Restore from iTune Backup
    10. Select "Restore from iTune Backup"
    11. You will be instructed to connect to iTune (computer)
    On computer
    12. Two options offered
    13. (a) Set up as new iPad (b) Restore from backup (a list of backup will be shown)
    14. Select Restore from backup and select the backup
    15. Continue
    16. Restoring iPad from backup
    17. The settings for iPad restored

Maybe you are looking for

  • How to return more than one object from SwingWorker

    I am using a SwingWorker to call 3 different methods of another class (data fetch class). Each of these 3 methods returns a String array. I am able to get the first array outside the thread code using the get() method of the SwingWorker class, final

  • ALV Tree Output

    Hi, In my present project we have requirement for developing ALV tree output using ALV configuration model in WD4A. Please provide sample code or tutorial related to ALV Tree development in WebDynpro ABAP. Best regards, Alleiah

  • How to record desktop with jmf?

    Hi, i'm new using jmf, so if it's a simple issue i don't know :S I'm trying to make an app that record the desktop. I have found this: http://java.sun.com/javase/technologies/desktop/media/jmf/2.1.1/solutions/JVidCap.html But when i run it: "! No Dev

  • Output message is not getting populated

    Hi My scenario is file->XI->file. I have created  source and destination data sturcture as follows mt_input dt_input FILE  xsd.string  0..unbounded mt_output dt_output OUTPUT xsd.string  0..unbounded i have mapped dt_input & dt_output and FILE & OUTP

  • Connect to SSTP Windows 2008 VPN

    How can we connect to a Windows 2008 Server SSTP based VPN? Is there an option in the Internet Connect builtin VPN setup or we need a third party client/tool? Thanks K.