Help adding new WLC to existing ACS

Hi All,
I need help with this.
This network has a working WLC that authenticates wireless users against an ACS by MAC address. It works fine.
I need to add a new WLC.
I added the WLC, the APs connect to the WLC fine, but the users get limited connectivity and we've found out that is because the new WLC is getting authentication errors against the ACS.
The configuration of the new WLC is exactly the same as the current working WLC and both controllers show as AAA clients on the ACS.
I want to know if somebody can point me out in the right direction to solve this.
There's connectivity fine between all devices (as far as PING goes), and there's no Firewall or filters in between.
The difference I see on both WLCs is that on the working one (WLC1), under Security - AP Policies, we see the AP Authorization List with the MAC addresses/cert type/hash. We don't get this information on the non-working WLC (attached document shows both)
Also in the attached document, I'm sending the errors I get no the WLC2 controller.
Any help is greatly appreciated.
Federico.

Federico,
I didn't get you when you say that you see only One WLC under groupsetup/Mac address. Could you please elaborate this?
Also, if you don't know see any NAR configured under shared profile component then check inside the group/user setup there must be either ip based or CLI/DNIS based NAR configured for WLC's and looking at failed attempts it seem that action is denied.
HTH
Regds,
JK
Do rate helpful posts-

Similar Messages

Adding new ipad to existing account - help!

I'd like to use both my old iPad and new on the same account, but "provide valid values" error message appears with each attempt on that initial page with "cellular #, email, passcode if required, and last four digits of SS#". Info is correct according to my account settings which I access via the old iPad.. Many repeat attempts here over the last week - what can I be doing wrong?

Sure - It's the ATT&T cellular account opened through my first ipad, for the that ipad. I'm hoping to add a new ipad to the account as I still wish to use the old one for awhile too.
On this new ipad, it seems it will allow this, but on the initial screen for cellular registration, I can't get beyond the remedial information. I feel like there is something ridiculously obvious I am doing wrong.
I'm hoping someone has done this before, and has insight as to what I am oblivious to.
Thanks!!

Adding new fields to existing cube

Hi all,
We have a cube with data, now we added 2 new fields to the datasource. And want to add two more fields in the Cube to correspond to the new fields. What would be the impact on the data that is already there in the cube? Can I go ahead and add the fields in the cube and start extracting data? What I want to know is what would be the implications in such a scenario?
Any insight or help would be appreciated and fully rewarded.
Thanks,
Mav

Hi,
At least from the experience I had there were no performance issues. The only issue would be in terms of the time taken to transport. The larger the amount of data ,longer the transport time.
You can continue extraction of data for those 2 fields from that point on. No need to empty the data from the cube and reload again. Only thing is that the data in the past for these 2 fields may not be mapped to the existing data in the cube. If you want to do that dump the cube and reload. Otherwise the data will be mapped from the time you start extracting the new fields with the data in the cube.
Cheers,
Kedar

Cancelling a line and and adding new lines to existing PO using API

Hi,
Can any one please help me know how I can cancel a line and insert new lines into a existing PO using any API.
Many Thanks,
Srinivas.

VanessaC_VZW wrote:
However, if you do not want a contract on the new lines, (since you will have your own equipment), the activation fee will be $35.00 per line. If you agree to a 2-year contract for the share lines, the activation fees will be $25.00 per line.
You can add the new lines by calling our Telesales Department at 800-256-4646.
Thank you,
Really?! I didn't know that made a difference...I thought secondary lines were $25 - well, ya learn something new every day!
And a side note - we added a line for my 75+ yr old mother with one of our old flip phones and CS was extremely kind in waiving the activation fee (I could have sworn it was $25 charged and credited on the bill), PLUS they boxed up the flip phone after activating it (with an out of state number to boot) and shipped it to my Mom, all at no additional cost to me. I'm not saying that will be everyone's experience, and I was amazed the service rep offered to ship it for me - but I smiled and said "THANK YOU!" and accepted it!

Help adding new Macs to the household, creating shared drive for iTunes,

I have a few questions:
My husband and I recently both got MacBook Pros. Our former set-up was a iMac which backs up to a 500 G Time Capsule. We have a large iTunes library and iPhoto library on the iMac. The iMac is going to turn in to the kids computer. I would like to do the following:
1. transfer photos to my MBP (#1). Will the Time Machine backup for the iMac become significantly smaller, making room for the soon to be larger backup of the MBP #1? Little confused how that is going to work.
2. have shared access to iTunes library? basically it would be nice for all 3 computers to have the complete iTunes library, but I would also like to backup all 3 computers using Time Machine and don't want to have triplicates of the library. I was trying to figure out if the way to go is to put the iTunes on a shared drive on the Time Capsule, but is there a way for the 3 computers to 'sync' to the shared drive when new music is added? Finally, if the iTunes is within a shared drive does that mean it won't be backed up?
Much appreciation and thanks to anyone who can help make sense of this.

Update: Downloaded free version of Syncopation, and am hopeful this is going to some what solve my iTunes issue.
New question would be: when creating the Time Machine backups for MBP#1 and MBP #2 can I NOT back up the iTunes folders? That would save approx. 36G on each of these backups, right? 72G total of the Time Capsule space. And the assumption is that with Syncopation, as long as the iMac iTunes is backed up then, you have everything.

Question on adding new server to existing pool in OVM 2.2 environment

I have an existing iscsi based server pool with one server attached to the pool. I am adding a second ovm server. I have configured the iscsi and multipath modules and can see the repository lun.
I then added the server to the pool via ovm manager, but the server is not fully participating as the agent did not create a mount point for /OVS so I can't see the repos directiories from the new server. A "df" does not show the device as it does on the first server.
The manager gui does show the server as part of the pool even though we received an error.
In the ovm manager log, we see the following messages.
Check prerequisites to add server (ovm2.highlinehosting.com) to server pool (san_pool1) succeed
During adding servers ([ovm2.domain.com]) to server pool (san_pool1), Cluster setup failed: (OVM-1011 OVM Manager communication with ovm1.domain.com for operation HA Setup for Oracle VM Agent 2.2.0 failed: errcode=00000, errmsg=Unexpected error: <Exception: ha_check_cpu_compatibility failed:<Exception: CPU not compatible! {'ovm1.domain.com': 'vendor_id=GenuineIntel;cpu_family=6;model=44', 'ovm2.highlinehosting.com': 'vendor_id=GenuineIntel;cpu_family=6;model=46'}> )
I'm not sure why it's complaining about cpu compatibility as we are not using any HA features at this time, and both servers are identical in make and model. They are both equipped with the same cpu type and speed.
I checked ocfs2 network connectivity by executing the command "nc -zv nodename 7777", which ran successfully from both nodes. The manager was able to propagate a valid cluster.conf file to both servers. I restarted the ovs-agent service on the new server.
Are there any other configuration steps that I need to take on the new server before trying to add it to the pool? I do need to tread carefully as I have live guests running in the pool.
Thx

Bob Weinmann wrote:
If I have to go the route of using a separate pool for each server, do you have any suggestions on how I would be able to access the repos of server1 from server2 if server1 were to go down hard? I don't mean to access it as a repos for running the vms, but just to be able to copy the vm files over to the running server.This would be possible if you were using NFS for your storage, but not if you're using FC or iSCSI, as the LUN is formatted with the OCFS2 cluster ID of each pool, so probably wouldn't be able to be mounted by another pool. Your best bet is to upgrade to Oracle VM 3.0 so that you can create a pool that contains both servers: you won't have live migration, but HA will still work just fine.

Adding new field to existing CO-PA data source

Hello BW gurus,
i was asked to add a new field vv531 in COPA data source, in order to do this when i was deleting the data source it is giving message "you are not allowed to change cross-client Customizing" .our bw development has 2 clients 20 & 40 . Generally wat ever changes are done in 20 are visible in 40. But now am not able to see the particular CO-PA data source in client 20.It is visible only in client 40. when i am trying to delete it from 40 it is giving the msg. Please suggest me over this bcause my dead line to complete this is nearing.
Thanks,
praveen

hello manfred,
thanks for the reply. i know for the fact tht we shud delete n recreate but when i am trying to delete it it is saying "you are not allowed to change cross client customising" . when the development was going on they have done it in development server client 20,which is also visible in client 40 with out transportation . 20 is whr changes are made ,40 is the one which is connected to BW development server. Now as per the requirement i shud make changes in 20 ,but when i am trying to do this it says "data source is defined in a different client" .pls help me out resolve this problem.
thanks&regards
praveen

Help adding new account to iTunes

I bought a new iPod and want to add another account to my iTunes. I would have thought this would be simple - and it probably is for anyone other then me - but I can't seem to figure it out. Can someone please help me...step by step? Thank you!!

Let's clarify, please. When you say "iTunes account" are you referring to the collection of tracks on your computer, or are you referring to an account with the iTunes Store?
If you mean that you want to have a collection of music on your computer separate from that you set up in iTunes for your boyfriend, and you want to keep your boyfriend's iTunes as it is, then what you need to do is set up a new Windows user account. Then you can have your iTunes separate from that of your boyfriend.
For more information, you might find the following sites useful:
The New User's Guide for iTunes
iTunes 101
iPod 101
Hope this helps.

Query on adding new node to existing 2 node cluster

Hi experts
current environment
Oracle VM 2 Node RAC cluster
Oracle 11G 11.2.0.3.0
Oracle 11g rel 2 GI
on current 2 node cluster we have GI and RAC db configured
Nodes: vmorarac1,vmorarac2
we shutdown vmorarac1 to clone it to vmorarac5
on new node I have changed the hostname to vmorarac5
In /etc/sysconfig/network-scripts/ifcfg-eth0 change ip to new ip and same for /etc/sysconfig/network-scripts/ifcfg-eth1
152.144.199.210,152.144.199.211
mad echanges to /etc/hosts on vmorarac1/2 for 2 new IP address assigned to vmorarac5
152.144.199.171 vmorarac1.pbi.global.pvt vmorarac1
192.168.2.30 vmorarac1-priv.pbi.global.pvt vmorarac1-priv
152.144.199.184 vmorarac1-vip.pbi.global.pvt vmorarac1-vip
152.144.199.172 vmorarac2.pbi.global.pvt vmorarac2
192.168.2.31 vmorarac2-priv.pbi.global.pvt vmorarac2-priv
152.144.199.185 vmorarac2-vip.pbi.global.pvt vmorarac2-vip
152.144.199.210 vmorarac2.pbi.global.pvt vmorarac2
192.168.2.32 vmorarac2-priv.pbi.global.pvt vmorarac2-priv
152.144.199.211 vmorarac2-vip.pbi.global.pvt vmorarac2-vip
152.144.199.201 vmorarac-scan.pbi.global.pvt
Query is is that all ok to reboot the new node to reflect changes as below and change the hostname to vmorarac2
152.144.199.210 vmorarac2.pbi.global.pvt vmorarac2
192.168.2.32 vmorarac2-priv.pbi.global.pvt vmorarac2-priv
152.144.199.211 vmorarac2-vip.pbi.global.pvt vmorarac2-vip
hostname change in /etc/sysconfig/network
please let me know
On new node vmorarac5, there is alreay software for RAC DB and GUI cloned from vmorarac1
addnode.sh is used to add existing node, but as part of pre-requisite configuratoin is there any config step missing
thanks

The only thing you want "cloned" is the base OS install... The GI home directory, the oraInventory and a whole lot of other stuff is configured at addNode time or cluster install time. I would say that proceeding with your current plans will corrupt your clusterware. You really need to STOP LISTENING to the SA's and START reading the documentation on how to add a node to a cluster. Simply changing the hostname IS NOT a supported "feature".
Start with a CLEAN OS. Configure shared devices, networks, /etc/hosts, memory and packages.
Follow the instructions for addNode.
Doing this any other way has the potential to corrupt your entire cluster.

Help adding new files to Jar file.

I am new to Java and am having problems haveing our Web App work after I have recreated the JAR file...this is what I did...
Changed to the following directory at a dos prompt:
D:\jdk1.3.1_01\bin
Ran the following to extract the files from the jar file.
jar xvf app2.jar
...this created 5 directories with various files.
copied new and updated graphic files to
D:\jdk1.3.1_01\bin\app2\images
Recreated the jar file using the following command (pv com javavp meta-inf borland are the 5 directories that were extracted from the original jar file above):
jar.exe cvf app2.jar pv com app2 meta-inf borland
I now have a new jar file that is a similar size, so it looks good, but when I put it in our web site, it does not recognize certain frames (that get information from the database) that it did before (the frames are blank)
Any thoughts on what I am doing wrong?
Also, are there any Windows programs that i can use to make this easier instead of using the dos commands?
Thanks...

To change the contents while inside a java program, you might be able to use Runtime.exec(String[]). Make the array with "jar.exe" as the first index, flags in the second, and remaining arguments in the remaining indecies.

Need Help Adding Flash Intro To Existing Site

OK I'm helping a buddy of mine out and he's already got his sie built for him by someone else, the index file is .php. Now I've got this little Flash animation that we want to run first, then when it's done go to his website. When I try to add it to the top of the index page all that happens is the site loads like in normally did but with the Flash movie at the top instead of being another page. What do we need to do to have it load on it's own first?

yes. the index.html should embed your flash intro swf and at the end to your swf (and in a skip intro button code) you should open the current main page (using getURL or navigateToURL).

Help adding photos to an existing Adobe slideshow

I have created my slidshows in adobe bridge CS5 and imported them into my website seamlessly. Now months later I am trying to figure out how I even did it!! I just need to add photos to the current slideshow, can this be done??
Thanks!

You will need to go into Code view and search for the UL tag with an ID of ImageSlideShow.
Once there, you can add a List Item (<li>) as per
<ul id="ImageSlideShow" title="My Images">
<li>
      <a href="images/photo.jpg" title="White Orchids">
        <img src="images/thumbnails/photo.jpg" alt="photo.jpg" />
    </a>
</li>
    
</ul>
The above assumes that your main image is stored in the images folder and is called photo.jpg. It also assumes that the thumbnail of the image is stored in the images/thumbnails folder and has the name of photo.jpg.
If your images are located in a different folder or has a different name, you will need to adjust the values in the example.

How can I apply existing WCS "WLAN Config" templates to a new WLC?

We've been running a pair of WLC 4402s managed by WCS, thus we are still on the older 7.0.235.0 (WCS) / 7.0.235.3 (WLC) release. I'm trying to add an additional WLC 4402-50 as a hot spare. I first ran the manual setup steps to give it an IP in our range, and used the WLCs web page to set our SNMP communities and such to the values used by our existing WLCs, then I added the new WLC in WCS.
At this point I could apply most of the "Controller Templates" from our existing configuration to the new unit. However, I can not get it to take our existing interfaces nor our WLAN Configurations. How do I avoid needing to recreate these from scratch on the new WLC?
We only have four dynamic interfaces, and each WLC needs its own IP address for each interface, so I did manually add these via the WLCs web page. However, now when I go to the WCS' "Configure > Contoller Templagte Launch Pad" page, then select "WLANs > WLAN Configuration", I see my usual list of WLANs, but can't figure how to push them to the new WLC.
For all of the other templates on the launch pad, I can select a template, click the "Apply to Controllers..." button, and I get a list that has my existing two and also the new controller. I can select the new controller, and apply the template, and it succeeds.
Yet if I select a specific WLAN config, and press "Apply to Controllers...", the list that appears has only my existing two WLCs, not the the new one.
In small green type at the top it says, "Controllers configured with Interface/Interface Group - 'w-restricted' and selected RADIUS server(s), LDAP servers, ACL Name with rules and Ingress interface are shown."
I have already manually added the interface "w-restricted" to the new controller, and have added the RADIUS servers via the template used by our other two WLCs. Not sure what to do about "LDAP servers, ACL Name with rules and Ingress interface", as we don't have any ACL rules, nor use LDAP directly from the WLCs (as all user ID stuff is via RADIUS).
Any hints on what manual setup I should add to get the new WLC in the list for these WLAN Configs?
Thanks,
Steve

To be honest, if your only adding another WLC, your better off creating the interface and WLAN's manually. I don't like pushing out templates to create new WLAN's. I would use it to adjust an existing WLAN, but that would be it. To me it's safer. Also your new WLC is on the same code? If you really want to figure it out, I would manually add the interfaces first then refresh the co fog from the new WLC and then push out the WLAN SSID and see if it takes. If not, don't waste your time anymore and create it manually.
Sent from Cisco Technical Support iPhone App

Adding New Dimension In An Existing Cube (Block)

Hi fellows,
Im not an expert so need you feedback.
I am supporting a cube that was built a decade ago using Essbase 6.5. It has 7 dimensions (3 dense, 4 sparse). With the new reporting requirement, I need to add a new dimension to be called "BaseTimePeriod" that seems like a Time dimension but will show the "Constant Dollar" amount calcuation for difference Scenarios.
Since the cube has been there for so long, and the expert that has pioneered that cube is no longer in the company. All of our reports uses API being called in MS Excel to retrieve data from the cube and format it the way the users wanted it to be. As well as 75% of our data are user input using the Essbase Excel Add-in, "lock/send" commands.
My problem now is that, since I need to introduce another dimension for the "Constant Dollar" calculation, is there any way that if I add a new dimension the existing process of uploading data by the users as well as retrieving data through Excel API will not be affected?
I tried to add new dimension in the R&D server that we have when I try to retrieve historical data from the cube in the Excel since there is "BaseTimePeriod" dimension before, the Excel report layout gets affected and inserts a new row placing "BaseTimePeriod" in that cell since this not yet there before. And when I try to upload data through Excel Add-in "lock/send" action, it did allow me unless I put a member from the "BaseTimePeriod" to complete the dimension member combination.
My questions now are:
1) How can I add a new dimension without impact from the historical data?
2) Is there any way to place a default value for the new dimension for the historical data so it would complete the dimension member combination, so whenever I retrieve and upload data there will be no problem?
Any insights related to this questions is highly appreciated. Thanks!
obelisk

If you add the new dimension to a cube that already has data, you should get a prompt when you save the outline to associate the existing data with a member from the new dimension. You will then go into a dense restructure which could take a while, depending on the size of your database. Another option would be to export your data in column format and load it into a relational table in something like SQL or Access, you can then add the new dimension to the export in the relational tool, export it back out to a text file and use a load rule to reload it.
As far as the lock & send and existing reports, in most cases, adding a new dim will result in all of those needing to be updated. This is why we try not to add new dims to existing cubes, especially ones that have been around a while.
Another thing to consider is the impact of adding a new dim. I don't know the size of your existing database, but you are going to increase it by adding a new dim and things like consolidation time and retrievals can be impacted, so you need to test all of this.
You should evaluate why you need a new dim and determine if you can achieve the same result without adding a new dim. While a new dim might be the preference in a new cube design, when dealing with something that has been around a while you might want to be creative and somewhat more compromising if it is the lesser of two evils. If everyone is committed to a rebuild then go ahead and rebuild especially if it's been around a while, there are probably other things that can stand to be cleaned up as well, but if nobody wants to deal with that, then look to see if you can get their without adding a new dim, perhaps a new roll up in a existing dim or an attribute dim. A more thorough explanation of what the business case is would help to provide an alternate solution.

Adding a field to existing collective search help

we tried to add a custom field to already existing collective search help
for this we tried to copy the search help exit "F4IF_SHLP_EXIT_VENDOR_EXP",
but we are unable to activate the copied function module since it's throwing a error that
a statement in one of the includes that was created by the system is inactive.
Thanks in advance,
Raj

Hi Venkata,
Datasource Enhacement:
Please check : [Enhancing LO DataSource u2013 Step by Step|https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/b0af763b-066e-2910-a784-dc6731660f46]
after adding new field to datasource, need to populate using ABAP code in User Exit.
Adjust update and transfer rules of 0Customer and load data.
how can I add that field in 0SD_C03 cube.
--> In 0Customer infoobject, make Sales District as Navigational attribute and also activate as navigational in CUBE: 0SD_C03. Then it will be available for reporting for navigation, filtering.
Hope it Helps
Srini

Help adding new WLC to existing ACS

Similar Messages

Maybe you are looking for