Help in QoS configuration on 3750E/2960X

Hello everybody,
I would like to configure QoS in VoIP for terminal Aastra in switches Cisco (with L3). As I am not very confident in this issue, I have thought to give a priority for VoIP considering output traffic from IP telephone. The IP telephones have an IP in range 10.5.160.0/22, so could it be this criteria valid for assigning QoS to the VoIP packets? The criteria would be:
ip access-list extended tel_VOIP
 permit tcp 10.5.160.0 0.0.0.252 any
 permit udp 10.5.160.0 0.0.0.252 any
Class-map match-all VOIP
Match access-group name tel_VOIP
Policy-map VOIP
Class VOIP
Set ip dscp 32
And then for the access voip ports, I would put this:
Interface giga0/x
switchport mode access
service-policy input VIDEO
service-policy output VOIP
 switchport voice vlan 6
 switchport access vlan n
 mls qos trust dscp
 power inline consumption 5000
Also I have another policy-map configured for input traffic for video which gives it pri 32.
I would like to know if traffic with maximum priority goes by queue out nº 1 by default. And if so, if this would be enough to guarantee video and voip traffic would go by this queue, which has by default 4 Mb shaped. Our video only takes 256Kb.
Another thing is if more than 4 Mb were needed in queue out, a way to assure video and voip traffic would be to configure this queue as priority queue-out, wouldn’t it be?
Please, I do not know how to configure queues and I only want to know if this would categorize voip and video traffic with a dscp of 32.
Thank you very much.
I am a bit lost about this item. And that is why I would prefer not configuring different weights for the out queues if not necessary. Please, make me any comment. I could send you my configuration. 

hello Yahsiel, 
Well, I must have mismatched signaling value with voice traffic value. What I would like to do is marking voip traffic and then reserving a bandwith for it. 
I have investigated and voip traffic comes marked with CoS 5, so I suppose I do not have to create an access-list, I could create a class-map for voip: 
class-map VOIP
match ip precedence 5
and then reserve BW for it: 
policy-map VOIP-VIDEO
Class VOIP
priority 1000
and then I could also set this policy in all the access ports with: 
service-policy input VOIP-VIDEO
I suppose I could include in this same policy-map the marking of VIDEO traffic which is: 
  class VIDEO
    set ip dscp 32
Also as you say I will have to put in the access ports the "mls qos trust cos" and in the trunk "mls qos trust dscp". 
Do you think now this would guarantee 1 Mb for voip in the out queue? Out queue 1 has a total of 4 Mb maximum shaped so I think this would run.... 
What about "auto qos voip trust" in the interface level for all the ports? Some people tell me this run ok, but I do not know if I must configure it or not. If I configured auto qos, I think I wouldn't have to policy voip traffic. 
Thank you for your soon reply. Really!!! 

Similar Messages

  • Switchport QoS configuration for WLC

    Hi guys,
    I am having a question about switchport QoS configuration for WLC. In the "enterprise mobility deployment guide 4.1", it says we can use both either "mls qos trust cos" or "mls qos trust dscp", depending on the mapping, however looking through Jerome's video tutorial on QoS in youtube, he actually mentioned that we need to keep this value as "mls qos trust cos", and I have also read from somewhere else that since controllers are layer 2 device, we do need to use "mls qos trust cos" on the switchport directly connected to the WLC.
    however I did see some configurations using "mls qos trust dscp" on the switchport, which is for 5508 WLC due to some hardware design in the 5508 WLC. so I just want to ask what is the differnece between these two commands when we use them for switchports connected to WLC, and does this command really specific for what controller platform we use or it only depends on code version?
    thank you very much for your time and help.

    Hi George,
    Thanks for your reply, however I am still a bit confused on the difference between the two commands...
    so in the deployment guide it does say we can do either one on the switchports connected to the WLC, so when should we use trust dscp instead of cos?
    it sort of make sense when we talk about WLC is a layer 2 device hence we should use cos, but we also have packets marked with dscp values and I think the controller will keep the value without any modification, then that means we can also use trust dscp in order for this mapping to be done correctly, is this correct?
    I did see some other people saying that when using turst dscp and did a packet capture, the values cannot be mapped correctly, but there are also cases that this works. expecially with 5508 series controllers, does it really have some hardware features that doing different things than the 4404s and the 2100 series?
    but still, in what situation should we trust dscp on switchports connecting to WLC and when should we use trust cos as a best practice? or we should just forget about trust dscp for switchport connecting to WLC?
    Thanks.

  • SRW Series QoS configuration for VoIP

    Hello Cisco experts,
    I have SRW224G4 switch in an office connected to the internet through port1, Asterisk server through port 9, Internal computers through ports 16-24.
    Currently, voice is cutting in the inbound direction when computer users are using Internet. I am trying to make some QoS configuration in which remote IAX2 phone, which uses UDP port 4569, will not be affected by Internet usage made by internal computers.
    I have logged in to the switch management webpage, I found a section for (QoS), but I need some help in specifying which parameter should I configure.
    Internet connection speed is 1mbps DL / 512kbps UL. I can configure Asterisk to mark packest with some TOS if required.

    One way to do it would be to configure Asterisk to assign a DSCP value of 46 to voice packets.
    Then on the SRW224G4, use:
    CoS Settings tab / QoS mode: Basic
    Basic tab / Trust mode: DSCP
    That would give priority to voice packets inside your network.
    Possible problems:
    your ISP will most likely clear DSCP markings on packets going out of the network
    rare case: your ISP might charge you more for packets marked with DSCP 46 (not likely on an ADSL connection)
    bottleneck will be the ADSL router, so if possible, you should implement QoS based on DSCP on that device
    if some PC based software uses DSCP markings, it'll get priority also
    Hope this helps!
    Cheers,
    Tamas

  • PLease help me to configure

    Hello Friends,
    I need your help to configure my voice setup.I have two location connected with a point-to-point leased line. Both the ends have different brand pbx installed. One is connected with R1 with the help pf a T1 voice card and Other is connected with R2 with the help of a E1 card. I am giving an attachment of the scnerio. Please help me to configure the cisco 3640 routers with H.323 gateway. I will be very thankful to you.My bosses has given me this work to do. Now I need your help. I have some exerience to configure E1 and T1 cards also have some knowledge of configuring dial pears.
    Thanks.

    Ok, this was the 2nd thing I was just about to recommend, and that was to not Trunk due to the E1/T1 limitation and just terminate and route everything H323. Both sides are CAS, just one is E&M Immediate and the other is R2-Digital. Unlike the 1st document I linked you are not trunking the connections you are using a PLAR to a voice-port. Essentially you are using a H323 dialplan to do this in a limited fashion.
    Unfortunately CAS doesn't support ANI unless you use FGD or FGD-EANA on the T1 side Router and PBX. Not totally sure on the R2 side but I believe you need to configure your PBX and R2 router to use R2-Digital Compelled, non-compelled or semi-compelled to get ANI information on that side.
    Reference these documents.
    http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a00800e2560.shtml
    http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a00800943c2.shtml
    http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124tcr/tdia_r/dia_d2ht.htm#wp1010243
    Please rate any helpful posts
    Thanks
    Fred

  • Help in the configuration of SAPCRM BP to EP 6.0 SP2

    Hi all,
    Need some Help on the configuration  of the CRM Business Package 6.0.2.2. to EP 6.0 SP2. I am following the guide for the same given on SAP HELP. I have activated the required BSP Services : crm_bsp_frame etc.
    And i have assigned the Account Manager role to one of the portal users. I have also configured the backend role to the backend user to which the portal user is mapped.
    Now, iam able to see the Account Manager's top and detail level navigation in the portal, but iam not able to see the iviews in it. The error is as below:
    Portal Runtime Error
    An exception occurred while processing a request for :
    iView : N/A
    Component Name : N/A
    Application URL 'http:///sap/bc/bsp/sap/crm_bsp_frame/entrypoint.do' is not valid! Please check the protocol and host entries for system 'SAP_CRM'..
    See the details for the exception ID in the log file
    The SAP_CRM system that i have defined is fine. SInce iam able to create an SAP Transaction iview out of it successfully.
    Any pointers regarding this will be very useful. Thanks

    Hello Mr. Ramaya,
              Your SAP_CRM system definition is missing the entries for web application server. Check your system definition.  This is why in following url your host and port are missing.
    <b>'http:///sap/bc/bsp/sap/crm_bsp_frame/entrypoint.do'</b>

  • Help required in configuring telnet

    Hi,
    We have two PIX 515E firewalls working in HA mode.
    I wanted to configure telnet access to firewalls from outside interface.
    PIX version is 6.3(5)
    I kept PC outside to outside interfaces.
    PIX outside IP is 10.10.200.3, inside IP is 10.10.202.5 corresponding virtual IPs are 10.10.200.2 and 10.10.202.7
    I have tried following configurations:
    pix(config)#telnet 0 0 inside
    pix(config)#telnet 0 0 outside
    pix(config)#telnet 10.10.200.0 255.255.255.0 outside
    pix(config)#telnet 10.10.202.0 255.255.255.0 inside
    pix(config)#telnet 10.10.200.200 255.255.255.255 outside
    I am able to telnet from internal interface side using inside ip address.
    But from outside test pc with IP 10.10.200.200 I am not able to telnet to PIX.
    I enabled logging console 5.
    when I tried to telnet to outside virtual IP it is not showing any traffic to firewall.
    If I try to outside interface I am able to see the traffic like
    packets received from source 10.10.200.200 to 10.10.200.3
    any help in this configuration. I wanted to telnet firewall from test pc.
    Regards
    SKRAO

    HI SKRAO,
    from security reasons is not possible to telnet to outside interface there is no way how to permit this you need you ssh instead of telnet
    here is more info about setting ssh
    http://www.ciscopress.com/articles/article.asp?p=25342&seqNum=3&rl=1
    M.
    Hope that helps rate if it does

  • Help required in configuring counting rule

    I have limited experience in SAP-HR configuration. Kindly help me quota configuration. The client has only absence type u2013 Earned Leave. The leave rule is the same for all the employees. The leave rules are:
    1.     The employees are credited with earned Leave on Jan 1 every year, for the attendance days put in during the previous calendar year.
    2.     The employee is eligible for Earned Leave only if he has attendance for at least 240 days during the previous year. If the employee has joined the company during the middle of the previous year, then he should have attendance for at least 2/3 of the remaining working days during the year.
    3.     The employee should be credited with 1 day EL for every 20 working days. If the employee, for example, has worked for 268 days during the year then he should be credited with 13 days EL (268/20=13, with 8 days as remainder). The remainder days, if any, should be carried forward to the next year and considered at that point as added to the number of working days. E.g. employee has worked for 268 days in year 2010. He will be credited with 13 days EL on 1 Jan 2011. Assume he has worked for 256 days in year 2011. Then while creating the absence quota for EL on 1 Jan 2012, the system should consider working days as 256 (from year 2011) + 8 (remainder from year 2010) = 264. Hence the employee should be credited with 13 days of EL on 1 Jan 2012 (264/20 = 13 days; 4 days remainder).
    4.     Leave carry forward rules: The employee is allowed to carry forward the EL balance to the next year. However, after carry forward the total balance should not go beyond 30 days. Any thing in excess of 30 days will get lapsed, if it is not encashed.
    Kindly let me know how to configure the counting rule & the deduction rule for the above scenario.

    Hi
    Configuring of EL need PCR Calculation and Standard Configuration with time Types
    000010            D VARSTCURMO
    000020 **           COLOP*
    000030 04         D VARSTFDYPP
    000040 04 N
    000050 04 Y       D HRS=0     HRS=FR11C HRS?300
    000060 04 Y *
    000070 04 Y <     D HRS-300   HRS*-1    ADDDB9509 ADDDB9558 HRS?15
    000080 04 Y < *   Z HRS=0     HRS=M9500 GCY ZAC2
    000090 04 Y < <   Z GCY ZAC3
    this when u go for GCY ZAC2
               D HRS?10
             D HRS/10    ROUNDH<60HHRS?CELACR
    *        D HRS-CELACRHRS?0
    * *        HRS*-1    ADDDB9501
    * >        HRS=0     ADDDB9500ZADDMB9500ZADDDB9501ZADDMB9501Z
    >          HRS=0     ADDDB9500ZADDMB9500ZADDDB9501ZADDMB9501Z
    <            HRS=0     HRS=CELACRADDDB9501 HRS=0     ADDDB9500ZNEXTR A
    <        A   ADDMB9500Z
    This when u click ZAC3
    000010            D HRS=0     HRS=M9500 HRS?10
    000020 *            HRS/10    ROUNDH<60HADDDB9557 HRS-D9509 ADDDB9556 NEXTR A
    000030 *        A D HRS*-1    HRS?0
    000040 * *          COLOP*
    000050 * >          ADDDB9501 HRS=0     ADDDB9500ZADDMB9500ZADDDB9509ZNEXTR A
    000060 * >      A   ADDMB9509Z
    000070 <            HRS=0     HRS=M9509 ADDDB9501 HRS=0     ADDDB9500ZNEXTR A
    000080 <        A   ADDMB9500ZADDDB9509ZADDMB9509Z
    This PCR is for EL with 300 Limit
    Regards
    Raja Sekhar

  • Please help me to configure 2504 WLC as secondary in N+1 HA mode. My primary WLC is 5508 and both have 50 AP license.

    Please help me to configure 2504 WLC as secondary in N+1 HA mode. My primary WLC is 5508 and both have 50 AP license. I want to deploy the AP in the same location.

    Go HERE:  https://supportforums.cisco.com/discussion/12219106/high-availibility-2500

  • Is there any limitation of firmware or hardware for QoS configuration (4400 controller & 1252 AP's)

    Hi Experts,
    Before proceeding for adding AP model 1131 and 1252 into my set-up , I need to know whether any limitation of firmware or hardware for QoS configuration in wireless set-up .
    I have 4400 controller and 1130 & 1250 AP models.

    Hi Vinod,
    Since you have 4400 controllers, you can run upto WLC 7.0.x code. Refer this for more detail
    http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
    there is no specific limitation to 1131/1252 AP model as such, everything is WLC software dependent.
    From later software 7.4.x,7.6.x,8.x, lots of improvement for QoS configuration & bandwidth control, but since your controller is old hardware, you cannot have those latest features.
    here is a reference post on how QoS works in wireless environment
    http://mrncciew.com/2012/11/28/understanding-wireless-qos-part-1/
    HTH
    Rasika
    *** Pls rate all useful responses ****

  • QoS Configuration for NME-AIR-WLC

    Hello,
    I have a question on the correct QoS configuration for a VoIP deployment. I have followed the steps referenced here but have two questions..
    1) The last recommendation in the list is to set DCA channel sensitivity to High to avoid changes during business hours. I think this should be Low? The manual states "Low—The DCA algorithm is not particularly sensitive to environmental changes."
    2) The recommendation is to trust dscp on AP uplinks and to trust cos on the WLC uplink. However I can't find any configuration guidelines for configuring QoS if the WLC in question is an NME hosted in a 2921.
    2a) The link between the switch and the 2921 is an 802.1q trunk so should I trust cos on this link rather than dscp?
    2b) What configuration should be on the 2921? Create a policy-map and apply it to the uplink port?
    2c) Should there be a service policy assigned to the In1/0 interface for the WLC itself?
    Any thoughts appreciated.
    Thanks,
    Dave

    Well I appear to have answered question 2 after I stopped being lazy and did some packet captures.
    No configuration required on 2921 as packets captured from In1/0 and Gi0/0 show correct DSCP markings on RTP and SCCP packets.
    Would still be interested to know on question 1 though.

  • Can anyone help me in configuring the reports server

    Can any one help me in configuring report server to personal web server on Windows NT 4.0 sp4 environment.

    Hi.
    One way of searching for tables that contains specific fields is use transaction ST05 (Performance Analysis) and then turn on the trace function.
    If you know some program that has a component (textbox, select-option, parameter, label, radiobutton, etc) that reffers to the field desired (or even just use it in the internal logic), in your case 'charg', you'll be able to check in a report what tables were used while the trace was on.
    Search about ST05 and its trace function. It's very simple and very useful to find tables.
    Edited by: Fabio Luiz Esperati Pagoti on Sep 29, 2009 7:40 PM

  • Need help on struts configuration with ColdFusion 10 using IIS

    We need help on struts configuration with ColdFusion 10 using IIS.
    Earlier we were using ColdFusion 8 with IIS 6 for one of our application.  This application internally calls struts. After upgrading to ColdFusion 10 struts calls are not loading. We get 404 error.
    In ColdFusion 8 struts were configured using  actions extension .do in IIS from this file-
    C:\ColdFusion8\runtime\lib\wsconfig\jrun_iis6.dll.
    But in ColdFusion 10 this file is not present as ColdFusion 10 uses Tomcat in place of Jrun.
    Also there is no information in ColdFusion log file.

    Duane wrote:
    doctormirabilis, Welcome to the discussion area!
    1) how can i configure the time capsule in order to operate as a remote base station synchronizing with the relay using the ethernet port?
    Configure the Time Capsule to act as a bridge (not distributing IP addresses). Also configure the Time Capsule to create an 802.11n wireless network with a unique network name (SSID). That's it.
    2) how can i avoid that my powerbook while accessing my wireless network does connect through the relay station instead of using the time capsule?
    Configure the Time Capsule to use a different network name than the WDS link between the 2 AirPort Express (AX). Configure the PowerBook to use the Time Capsule network.
    There are 2 pieces of information that you should be aware of...
    (1) None of the PowerBooks are capable of 802.11n.
    (2) The WDS link cuts your available bandwidth in half. So the wireless link to your neighbor's has a maximum potential of 27 Mbps.
    Let's for a minute assume that you have a Mac compatible with 802.11n. In your configuration the time you could take advantage of the 802.11n speed is when the Mac is sending/recieving data directly from/to the Time Capsule.
    There would be NO speed increase in Internet access. The speed of Internet access is going to be controlled by the slowest link in the path to the Internet. That is probably the connection to the ISP. The next slowest path is the WDS link to your neighbor's.
    Duane,
    I am in a similar situation, sharing internet with my neighbor. Do you think it would be plausible to hook up a vonage phone adapter to time capsule's ethernet port if time capsule is bridging from my neighbor's router in the configuration you have described? A check of my upload speed shows 1.67Mbps (powerbookG4 w/ airport extreme). Vonage reccommends 90kbps minimum upload speed. Am I going to lose some speed putting the Vonag adapter behind time capsule?
    Thank you

  • WAP4410N Help on to configure dhcp OR dhcp CLIENT

    Help on the config. WAP4410N
    WAP4410N Help on to configure
    HI  Guys,
    I have 2 Wireless Access Points WAP4410N. Iam very new in Using these Wireless ACCESS points. initial configuration I have done with the help of Starting guide. Here i want to know few things
    1) Is these can be configured By CLI mode as of now i used GUI mode.
    2)i want to give connected users of wifi from the DHCP loop created in L3 switch (is a DHCP server). where wifi point is connected to a port of L3 switch.
    3) How can i give connected wifi users from  DHCP Pool with different ip adress subnet to internal users and guests. is this can be configured here on product i have or not?
    if yes . can you please exlain me or gvve me detaiuled stuff.
    4) I Want to give access to my employees internal server through WI-fi . where i  have L3 switch  connected  to a server gi 1/0/1 (10.10.10.10) and wifi at port gi 1/0/2. how can segregate or seperate the internal user employees with access to servers and gust users directly access internet through gateway 10.10.11.1 connected to L3 switch. where wifi port has to be given a different VLAN no.
    wifi-----------------------L3 switch--------------------------router
                             server

    Hello all
    I had an issue.
    , added SSID with different VLan numbers. everything went good. i can access the WAP but couldnt connect to internet where i can ping from connected WAP to Gateway of our network . but couldnt connect to internet.
    the status on the connected WAP says. Limited access. No internet access.......
    Any help guys. is there any problem with my laptop searched through online restarted the Netsh service of TCP and all .. but lost couldnt connect to internet and the status still shows No internet access..\\
    Really ****** on with WAP4410N working with it from 4days. atlast connected to WAP and the new issue arises with no internet access...
    Thanks
    srikanth

  • MLS QoS configuration

    Good Morning, everyone.  I am looking for some clarification with an existing 3750x Switch configuration.  
    I am reviewing the configuration of my network switches and found the following MLS QoS configuration on one of my switches and a partial of this same config on another switch.  Can someone please explain what function, this line of code, is performing; and is it necessary?
    mls qos map policed-dscp  0 14 24 30 38 to 8
    mls qos map policed-dscp  10 to 12
    mls qos map policed-dscp  12 to 14
    mls qos map policed-dscp  26 to 28
    mls qos map policed-dscp  28 to 30
    mls qos map policed-dscp  32 to 34
    mls qos map policed-dscp  34 to 36
    mls qos map policed-dscp  36 to 38
    mls qos map cos-dscp 0 8 16 24 34 46 48 56
    mls qos srr-queue input bandwidth 70 30
    mls qos srr-queue input threshold 1 80 90
    mls qos srr-queue input threshold 2 80 90
    mls qos srr-queue input priority-queue 2 bandwidth 30
    mls qos srr-queue input dscp-map queue 1 threshold 2 16 24
    mls qos srr-queue input dscp-map queue 1 threshold 3 48 56
    mls qos srr-queue input dscp-map queue 2 threshold 1 36 38
    mls qos srr-queue input dscp-map queue 2 threshold 2 32 34
    mls qos srr-queue input dscp-map queue 2 threshold 3 40 46
    mls qos srr-queue output cos-map queue 1 threshold 2 4
    mls qos srr-queue output cos-map queue 1 threshold 3 5
    mls qos srr-queue output cos-map queue 2 threshold 1 2
    mls qos srr-queue output cos-map queue 2 threshold 2 3
    mls qos srr-queue output cos-map queue 2 threshold 3 6 7
    mls qos srr-queue output cos-map queue 3 threshold 3 0
    mls qos srr-queue output cos-map queue 4 threshold 3 1
    mls qos srr-queue output dscp-map queue 1 threshold 2 32 34
    mls qos srr-queue output dscp-map queue 1 threshold 3 40 46
    mls qos srr-queue output dscp-map queue 2 threshold 1 18 20 22 26 28 30
    mls qos srr-queue output dscp-map queue 2 threshold 2 16 24
    mls qos srr-queue output dscp-map queue 2 threshold 3 48 56
    mls qos srr-queue output dscp-map queue 3 threshold 3 0
    mls qos srr-queue output dscp-map queue 4 threshold 1 8
    mls qos srr-queue output dscp-map queue 4 threshold 2 12 14
    mls qos srr-queue output dscp-map queue 4 threshold 3 10
    mls qos queue-set output 1 threshold 1 100 100 100 100
    mls qos queue-set output 1 threshold 2 80 90 100 400
    mls qos queue-set output 1 threshold 3 100 100 100 400
    mls qos queue-set output 1 threshold 4 90 100 100 400
    mls qos queue-set output 1 buffers 15 30 35 20
    mls qos
    If more information is required for a response, please let me know.
    Thank you, E.

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    The function of each command is perhaps best explained by the Command Reference and Software Configuration Guide for your IOS version.  If you have a question that's unanswered by those, please post another question.  BTW, Cisco also publishes whitepapers that further explain some subjects.  There are a couple on 3750 QoS.
    Regarding whether a particular command is necessary would depend on what your QoS policy is attempting to accomplish.

  • QOS configuration for Wireless voice over IP

    HI, I've been asked to install approx 5 wireless phones on a network that consists of the following:-
    1 x 4006 core switch
    8 x 3550 Access switches
    6 x 1100 AP's (that are connected to the Access switches.
    My question is this - does anyone have a basic QoS configuration that I can place onto the LAN infrastructure (Core/Access switches).
    Kind Regards
    Steve

    Should refer to http://www.cisco.com/en/US/products/hw/phones/ps379/products_implementation_design_guide_book09186a00802a029a.html. Also Cat 4K should have Sup2+ or higher to support voice.

Maybe you are looking for