Help -- iPod Nano loses charge quickly and won't start up

When I don't use the iPod for a few days and then try to start it up, it won't turn on at all. The only way I can get it to work is to connect it to the computer. It also seems to lose its charge quickly. I sent it back to have it checked out and I was told it worked fine, but I continue to have the same problems. I'm stuck. Any suggestions? Would Restore help?

A restore may help.
How are you trying to turn it on though?
See this as well...
About Sleep, Deep Sleep, Hibernation, and Sleep Timer
Finally, does resetting it turn it on?
Resetting iPod
For the battery issues...
Tips And Tricks For iPod Battery
iPod Battery Unplugged
Caring For iPod Battery
About the iPod Battery
And use this to test how long the battery actually lasts...
How To Determine Your iPods Battery Life
btabz

Similar Messages

  • My ipod nano has stopped shuffling and won't re-sync

    My ipod nano has stopped shuffling and won't sync to begin shuffle again

    http://www.apple.com/support/ipod/service/prices/ look up your model and country and if your willing to pay that much im not sure how you go about getting it done,
    Hope this helps,
    Quin.

  • My ipod nano 7g went off and will not start, this happened after I connect to my computer, my ipod will restart and I no longer turn on. I do?

    please help me my ipod nano 7g went off and will not start, this happened after I connect to my computer, my ipod will restart and I no longer turn on. what I do?

    Hey saintbless,
    Thanks for the question. The following article outlines troubleshooting information for iPod nano. While it mostly refers to the 6th generation, most steps apply for your model as well:
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS3474
    Will not turn on or screen remains dark
    - Connect iPod to power for at least ten minutes to ensure that the battery has enough charge to allow iPod to turn on.
    - If iPod does not turn on after ten minutes, try resetting the device while it is still connected to power. Reset the iPod by holding down the Sleep/Wake button and the Volume Down button for at least eight seconds or until you see the Apple logo appear.
    - If the Apple logo appears on the display, connect iPod to a computer and verify that it appears in iTunes and can play music. If iPod appears in iTunes and can play music, no further troubleshooting is needed.
    - If the screen remains dark and will not turn on, then your iPod may need service.
    Thanks,
    Matt M.

  • HT1339 HELP my ipod nano has completed frozen and won't do anything

    my ipod has complete frozen won't turn on or off and won't work charging by the mains or via the computer, i wanted to do a master reset but i can't even do this, please can anyone help

    Have you tried a hard reset yet?
    How to reset iPod
    B-rock

  • 6th gen ipod nano has white screen and won't go into disc mode

    My ipod nano has a white screen - it will play music, and it is recognized by itunes. It won't enter disc mode. I can't seem to find any other helpful steps to follow online other than put it into disc mode and restore it via itunes. When I attempt to put it into disc mode holding power/Vol down together the screen will turn back, but when I then hold down Vol down/Vol up together while the screen is dark it just goes back to white screen. I did plug it into the computer and restore it via itunes, and the screen is still white.  Any ideas?  Thanks!

    Hi LizS5,
    It sounds as if you have already done much of the troubleshooting suggested in this article, but I would suggest you work through it in order to get your iPod nano back up and running -
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS3474
    Specifically -
    Try putting the iPod into disk mode:
    Reset the device (press the Sleep and Volume Down buttons simultaneously until the display turns black—about eight seconds).
    When the display turns black, hold down the Volume Down and Volume Up buttons simultaneously until the device enters Disk mode.
    While the device is in disk mode, sync it to iTunes and try to restore.
    And if the issue is not resolved -
    My issue is still not resolved. What do I do next?
    For information on servicing your iPod, go to the iPod Service FAQ
    Thanks for using Apple Support Communities.
    Best,
    Brett L

  • IPod Nano turns itself on, and won't stay off

    Hi, everybody!
    I've had my iPod Nano for about two years now, and have noticed this problem occasionally, but it usually goes away and it has never been this bad.
    Here is one scenario: I turn my iPod off by holding the play button. The screen fades to black. I move to set my iPod down, and it immediately lights up again. I press and hold the play button, but instead of turning off, the iPod begins to play music. I pause the song and press and hold again. The iPod fades to black, but again lights up the minute I move my hand.
    Here is another scenario: the iPod has been off for several hours. Suddenly, it lights itself up. I pick it up and turn it off, but it again continues to light up as it sits on the desk.
    This, of course, runs down the battery--I've had to charge my iPod every day for the past few days because it kills itself, waking up over and over when I'm not around to turn it off again. I'm used to only needing to charge it every few days.
    I've tried setting the hold switch once I do get it to sleep, but all that means is that I then have to take it out of hold again a few seconds later to turn it off when it lights itself up. I've restarted over and over, but it keeps happening. I've also recently restored it, with no results. I don't have any alarms set, and there is nothing on my iPod but music and album artwork--no calendar, etc.
    It seems to do this most when I am moving around the room. I'm wondering if, somehow, it has become hyper-sensitive and is waking up because it thinks it's being touched? (That sounds so creepy.) It also wakes up instantly if I touch the USB port on the bottom. But of course it also must do this when I'm not around, because often I'll come into the room to find the battery 50% lower than it was when I left. (And I'm the only one who uses my iPod.)
    As I said, this has happened before over the two years of its life, but over the past three days or so, it has become nearly constant. I haven't dropped the iPod, it hasn't gotten wet, I haven't done anything unusual with it, so I am at a loss to explain the sudden recurrence of the issue.
    I'd appreciate any kind of help!

    Try resetting the iPod Nano - iPod Nano 5th Gen. User Manual

  • Ipod Nano Error 1417 Tried and won;t work

    I've tried looking through the restart method, the disconnect and reconnect method, and nothing works. My Ipod Nano is Ver. 1.0, and the update process does not pop up with a dialogue box, all it does is 'updating' but it's really doing nothing, help?

    are you still at an itunes version 7.0.0.70, Chang?
    to check, go "help > about itunes" and wait for the version number to scroll up from the bottom of the screen.
    if you've still got a 7.0.0.70, first try an upgrade to 7.0.1.8:
    iTunes 7.0.1.8 Installer
    if you still get the 1417 when using 7.0.1.8, let's get your iPod Updater logs to the Apple engineers for a look.
    Open this folder:
    C:\Documents and Setings\yourusername\Application Data\Apple Computer\iTunes\iPod Updater Logs
    (You may need to show hidden files in order to see the Application Data folder. Open up My Computer, and in the Tools menu, choose "Folder Options..." Then go to the View tab, and then in the "Advanced settings", select "Show hidden files and folders.")
    Send the files inside the iPod Updater logs folder as attachments to this email address.
    In the email to Roy, be sure to include the following information:
    - A link to the thread on Apple Discussions where the issue is being discussed
    - The username you are using in the thread
    - The version of iTunes you are using or trying to use
    - A concise description of the issue you are seeing
    - The exact text of the error message you are seeing

  • IPod Shuffle seen as iPod Nano in iTunes 6 and won't load music

    I had iPod shuffle linked to one computer, then changed computers. Tried loading iPod software from installation disc and iTunes 6 then looking at iPod. Initially got message indicating that iPod was linked to another computer - did I want to change link to this computer? I clicked 'YES' and all was well...until I tried the iPod updater. Following that my iPod Shuffle was recognized as an iPod Nano and would not accept any music through iTunes. I have tried uninstalling and reinstalling software multiple times with no success. I am still able to use iPod with old computer, but those days are numbered... Need some suggestions to remedy this. Thank you.

    those symptoms can sometimes be caused by a Windows drive letter confusion. are the techniques from this document of any help with that?
    Windows confuses iPod with network drive or hard drive and may keep iPod from mounting or songs may seem to disappear

  • Ipod nano 7th keeps flashing and won't turn on

    my ipod nan 7th generation is flashing on the blue screen and I can not turn it on...

    Hi peggic,
    It sounds like your iPod Nano isn't functioning properly. I have located an article which you may find helpful. It contains a series of troubleshooting steps you may want to consider:
    iPod nano (7th generation): Hardware troubleshooting - Apple Support
    Thank you for contributing to Apple Support Communities.
    Take care,
    BobbyD

  • Ipod Nano 4th or 5th generation won't recognize Itunes and shows loading constantly when I am on Nike plus

    My Ipod Nano all of a sudden won't show up on my Imac computer nor will it show up in Itunes.  I use it for running and I use the Nike + software, at the same time the recognition problem occurred when I click on the Nike + on my Ipod Nano it shows the circle and says "Loading".
    Also when I plug it in to the computer it says Connected do not unplug unless you eject, however there is no icon on my Imac to eject.
    Even when I reboot the Ipod Nano, the same thing happens...the Nike + just says loading and it doesn't get recognized by my Imac.
    Help what do I do????? I have tried rebooting several times, as well as using another mac and no luck. I even sent an email to Apple but so far no answer.  Any clue how to fix this?
    I think it has something to do with the Nike+ application, but don't know what to do.
    Thanks!

    Ipod Nano 4th or 5th generation
    Identifying iPod models
    iPod Manuals
    My Ipod Nano all of a sudden won't show up on my Imac computer nor will it show up in Itunes.
    http://support.apple.com/kb/TS1410 iPod not recognized in iTunes and Mac desktop
    I even sent an email to Apple but so far no answer.
    U.S. iPod and Mac technical support: 1-800-APL-CARE (1-800-275-2273) 

  • Pls help me my ipod nano wont charge even if i use other laptop or pc . The battery notification tells its full charge but when i remove my ipod its still not charged

    Pls help me my ipod nano wont charge even if i use other laptop or pc . The battery notification tells its full charge but when i remove my ipod its still not charged

    Is it not charging at all? Did you try to reset? If YES to both, request for a replacement of the ipod. Battery or the unit itself is defective. Cheers!

  • My ipod nano was charged and now the screen is all white

    my ipod nano was charged overnight,  now the front screen is all white  i cannot see anything(playlists etc)   i have reset it and the screen comes back on but only for a minute  then it goes right back to a white screen....    what is wrong with this and how do i fix it?

    If none of the 5 R's of troubleshooting are able to solve the problem, the issue is hardware related, meaning you'll need to have the iPod serviced or replaced.  The LCD screen may have simply burned out or wore out over time.
    http://www.apple.com/support/ipod/five_rs/.
    It wouldn't also hurt to the let iPod's battery full drain. Then charge the iPod back up and go through the 5 R's again.
    B-rock

  • Ipod nano 5th is unrecognized and rejected after downloading new itunes on Windows 8. Everything works on both- can use ipod and charge, but no recognition, no sync. Whassup? Did something get lost in the itunes update?

    Ipod nano 5th is unrecognized and rejected after downloading new itunes on Windows 8. Everything works on both- can use ipod and charge, but no recognition, no sync. Whassup? Did something get lost in the itunes update?

    I'm having the same problem. I wish someone could respond with a solution for this! I've paid money for new songs and can't listen to them because of this! WTH APPLE?!?!?!?!

  • As I downloaded new software upgrade in my iPod nano 7 th gen and also new iTunes upgrade then all data on my iPod got erased and now when I am trying to sync it again then sync button is disabled on the windows screen . Kindly help

    As I downloaded new software upgrade in my iPod nano 7 th gen and also new iTunes upgrade then all data on my iPod got erased and now when I am trying to sync it again then sync button is disabled on the windows screen . Kindly help

    From the OP: "My old computer got a virus and when that happened all my music was lost. "
    They don't have the music on their computer so they cannot transfer the iTunes folder, from the computer to their iPod and then to the new computer. And if they try to enable disk use on the iPod it will erase all the music that is on it. The method you cited is moving the files in a data format using the iPod as a flash drive. It doesn't work if they are in music format. That is why I suggested Yamipod.

  • How to turn on 6th gen iPod Nano after charging?

    Hello, could anyone help me with this issue:
    My iPod Nano was completely drain out of battery so I was charging it this morning, I want to ask is it normal when your iPod doesn't turn on quickly after charging after completely out of battery? is it different from iPhone (in iPhone it will show charging sign)?
    What should I do to check if my iPod is charged correctly? or this is a sign that my iPod was broken? please help, thanks
    I left my iPod at home and still charging it for the next two hours.hoping it will turn on again.

    Hello greenmous,
    And welcome to Apple Discussions!
    If the iPod's battery had fully drained, it could take up to at least half an hour before your iPod begins to show any signs of life, depending on whether you have it plugged into a USB port on your computer or connected to an external power adapter.
    For now I would let it be. If still no signs of life after a while, try resetting the iPod.
    To reset iPod nano:
    First, make sure iPod nano is charged. Then press the Sleep/Wake button and the Volume Down button for 6 seconds, until the Apple logo appears.
    B-rock

Maybe you are looking for

  • How to allow access to web/application servers on ports other than 80

    I have an iBook G4, running OSX 10.4.11, in a wireless network at home.... I'm developing an app that runs on JBoss (port 8080) and I want to expose it to the other computers on the network so I can see how it works with IE (i'm using Safari and Fire

  • JSF 1.2 f:attribute

    I am using Jsf 1.2 and <f: attribute> on any page does not work now. I try to use it just in form Something like : <h:form> <f:attribute name="init" value="#{bakingBean.property}"/> </h:form> property bind to a method what return boolean. and the met

  • Somebody help me get started

    OK I admit it, I'm a Mac rookie. Before getting my first Mac, I used Google calendar (as well as Google everything else). Now I'm using iCal, or trying to. I successfully merged my google cal into ical, and into my iPod, which is great except that I

  • Safari 5.0.6 crashing

    I realise there are many threads on this but I haven’t been able to find a solution. Safari keeps crashing, yet when I log on as another user (we have a separate log in for the kids), Safari is fine. I realise this might be something to do with Cache

  • Sort taxonomy folder manually

    Hi, I want to sort my taxonomy folders manually within an iView. This is possible for normal/standard KM-Folders, but not for taxonomy structures. Has anyone an idea how to realize manual sorting of these folders? Thanx Christoph