Help please, connectivity problem

Hello, I recently purchased an E2000. In generally it works great when I am online. However, I am having a big problem. There are a couple of webpages, or games, that I would like to remain connected to at all time.
When I idle for 15 or more minutes the router drops the conection, however, when I unplug the router and connect straight to the modem I do not have this problem. I am running through a cable modem, road runner service. Any idea how to keep the connection alive?
I appreciate your help.

Are you getting the problem on the wired computer or on the wireless computer...?

Similar Messages

Help please.connected my current iphone to i tunes it syncd old contacts from previous job to new phone and deleted all my new ones,

Help please.
Connected my current iphone to i tunes. it syncd old contacts from previous job and previous phone to new phone and deleted all my new ones. tried to do back up from earlier restore in i tunes but there only seem to be back ups from my old phone not the new one prior to its first sync...

thanks for your reply and input but, Im not sure if it was former or latter that I did, however I do know that I named this latest i phone differently and would have been OK with and expected expected old contacts to be added to the new ones I have recently added directly onto the new phone since I have had it rather than just the old one. I did try the undue/ unsync but this just seemed to remove all the old backed up ones just added leaving contacts empty? Clearly its my error, but what can be done to restore setting back to time before I connected today? earlier reset points on itunes show as 2 years ago and relate to old phone.

Please help! connection problems

ok I've been working on this for several hours now and can't figure it out. I just moved back home and my connection was working some yesterday but I can't get it to work anymore.
It says I'm connected but it won't receive any packets. I changed the SSID name and removed the old SSID's. I reinstalled my wireless pci card drivers and switched pci slots. I updated the router's firmware (it's WRT54G). I changed Advanced Wireless Settings as suggested: Beacon Interval: 50; lowered Fragmentation and RTS threshholds by 40 each. I switched the router to channel 11.
I've tried repairing the connection many times (some times it works, most times it won't renew IP address); I've also reset the router many times.
My computer skills are intermediate but certainly not advanced. I can't directly connect it to the modem via cable b/c I don't have the necessary hardware (modem card?). I talked to tech support and I was able to "ping yahoo.com," google, etc successfully but it just won't receive packets...Please help!

The best thing to do at this point is to go back over setting up the wireless security settings again and make sure that while you are setting up these settings that you connect an Ethernet cable from that computer to the router then perform a power cycle
You need to remove the power cable from the Linksys router, then remove the power cable from the modem, wait about 60 seconds, then plug in the modem, then plug in the Linksys router. Wait about 3 minutes while the modem and router sync back up. Once all light are back on,disconnect the ethernet cable and now try to connect.
Here are instructions to follow if you need them
Setting up your wireless connection in your router.
*** Step #5 = you can choose the type of encryption that fits your set-up, the example I give is: WPA/TKIP+AES
***Also Pay close attention to the security and security key information and make sure it matches. (What is entered in the router must be entered in the computer.
1.Open Internet Explorer and type 192.168.1.1 into the address bar.
2.You will now get a sign-in box, User Name = (Leave Blank)
                                                       Password = admin (all lower case letters)
3.Once the set-up page opens, click on the Wireless Tab as youwill need to change the settings. A) Wireless Network Mode = Mixed
              B) Wireless Network Name (SSID) = Choose any name and do not use Linksys.
              C) Wireless Channel = 1, 6 or 11 is best, so see which work best for you.
              D) Wireless SSID Broadcast = Enabled.
4. Now go to the bottom of the page and click on save settings.
5. Click on the Wireless Security Sub tab.
              A) Security Mode: WPA
              B) WPA Algorithms: TKIP + AES
              C) WPA Shared Key: Type 24 letters, and numbers using lower and upper case letters
              D) Group Key Renewal: 3600
6. Once again go to the bottom of the page and click on Save Settings.
7. Now you can close out of this page.
8. You will now need to enter the security info into your computer. I will now give you 2 links, depending which operating system you have, Vista or XP you will follow the one you have.
Vista = http://www.home-network-help.com/wireless-adapter-configuration-in-vista.html
XP = http://www.home-network-help.com/wireless-adapter.html
Now try to make a wireless connection.
Good Luck,
Ttech

Please help with connection problem!

Hi people,
I am trying to use Siemens Speedstream 4200 modem to connect to the internet using its ethernet port. It is connected via USB to my wife's HP Pavillion DV9000 laptop (Win XP)and works fine with that. Almost all hardware in Brazil where I live does not support mac, so I'm not sure if the modem is made only for PC. I imagine that's unlikely. I have tried using both a simple direct ethernet connection to my mac as well as via my airport base station (which I initialised) but to no avail.
My airport is connected and has the IP address 10.0.1.2. I have also checked 'set serice order' to make sure the correct method of connection is at the top of the list. Do I need to find out some of the PC's network info to apply to my mac's setup?
Please, any help most appreciated as I need to connect for my work.
Thanks! Ben

1st the technology is the same worldwide, and it is not restricted to Mac only or Pc only the technology works on all compuuters irreguardless of the manufacture.
Turn off the Modem you are using and the same with the Airport Base.
Plug the ethernet into the Speedstreme Modem and into the Airport Router start the Modem first and wait a minute and then do the same to the Airport Base.
If your wifes PC is wireless it should connect as well as the Mac.
Get the Mac working first. The Pc should connect as well as the Mac either way with Ethernet or Wireless, if she has a wireless card in her's.
Don't be afraid to consult the paperwork that came with the Airport, or Airport Extreme Base.

Help please! Problem accessing db connections from servlets

Hi all,
I am creating a web application using MVC architecture using jsp,servlets and beans.
I have created a login.jsp which accesses the LoginHandlerServlet.class.
in login.jsp there are two fields. One is username and one is password. When fields are filled and submitted it redirects it to LoginHandlerServlet. Now in the servlet it calls a passwordBean which in turn calls a connectionBean which gives the connection to passwordBean and passwordBean checks the username and password and returns the result to servlet.
Now when I run this application through tomcat. I am getting a error
Error : oracle:jdbc:Driver:OracleDriver
But when I append a main method in passwordBean which calls the corresponding method my driver gets initialised and I get the perfect output.
Please let me know what is wrong with this. Thanking you all in advance.
Regards,

Hi All,
This is the error I am getting :
SQLError :oracle.jdbc.driver.OracleDriver
java.lang.ClassNotFoundException: oracle.jdbc.driver.OracleDriver
at org.apache.catalina.loader.WebappClassLoader.loadClass(WebappClassLoader.java:1428)
at org.apache.catalina.loader.WebappClassLoader.loadClass(WebappClassLoader.java:1274)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:313)
at java.lang.Class.forName0(Native Method)
at java.lang.Class.forName(Class.java:120)
at com.ge.med.digit.egsnos.model.JDCConnectionDriver.<init>(JDCConnectionDriver.java:27)
at com.ge.med.digit.egsnos.model.connectionBean.<init>(connectionBean.java:48)
at com.ge.med.digit.egsnos.model.passwordBean.defineUser(passwordBean.java:61)
at com.ge.med.digit.egsnos.servlets.loginHandlerServlet.doPost(loginHandlerServlet.java:62)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:247)
at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:193)
at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:260)
at org.apache.catalina.core.StandardPipeline$StandardPipelineValveContext.invokeNext(StandardPipeline.java:
643)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:480)
at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:995)
at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:191)
at org.apache.catalina.core.StandardPipeline$StandardPipelineValveContext.invokeNext(StandardPipeline.java:
643)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:480)
at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:995)
at org.apache.catalina.core.StandardContext.invoke(StandardContext.java:2396)
at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:180)
at org.apache.catalina.core.StandardPipeline$StandardPipelineValveContext.invokeNext(StandardPipeline.java:
643)
at org.apache.catalina.valves.ErrorDispatcherValve.invoke(ErrorDispatcherValve.java:170)
at org.apache.catalina.core.StandardPipeline$StandardPipelineValveContext.invokeNext(StandardPipeline.java:
641)
at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:172)
at org.apache.catalina.core.StandardPipeline$StandardPipelineValveContext.invokeNext(StandardPipeline.java:
641)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:480)
at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:995)
at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:174)
at org.apache.catalina.core.StandardPipeline$StandardPipelineValveContext.invokeNext(StandardPipeline.java:
643)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:480)
at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:995)
at org.apache.coyote.tomcat4.CoyoteAdapter.service(CoyoteAdapter.java:223)
at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:405)
at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.processConnection(Http11Protocol.java:38
0)
at org.apache.tomcat.util.net.TcpWorkerThread.runIt(PoolTcpEndpoint.java:508)
at org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run(ThreadPool.java:533)
Thanks

Need help for connection problem

When I try to run JdbcCheckup.java, I get following problem:
password: tiger
database(a TNSNAME entry): myhost:1521:orcl
Connecting to the database...Connecting...
Exception in thread "main" java.sql.SQLException: Io exception: The Network Adap
ter could not establish the connection
at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:114)
at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:156)
at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:269)
at oracle.jdbc.driver.OracleConnection.<init>(OracleConnection.java:212)
at oracle.jdbc.driver.OracleDriver.getConnectionInstance(OracleDriver.ja
va:251)
at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:224)
at java.sql.DriverManager.getConnection(Compiled Code)
at java.sql.DriverManager.getConnection(DriverManager.java:137)
at JdbcCheckup.main(Compiled Code)
I'm very appreciated for everybody's help
null

This example can be run without specifying a TNSNAME connection string, as the oci8 jdbc driver will default to the localhost. OR - Specifying the only the TNSNAME is required, i.e. edit %ORACLE_HOME%\network\ADMIN\TNSNAMES.ORA file and locate the XXXXX.WORLD entry in the file. This is the TNSNAME entry referred to.
Try re-running this as follows (with no TNSNAME entry at all):
%ORACLE_HOME%\jdbc\demo\samples\oci8\basic-samples> java JdbcCheckup
Please enter information to test connection to the database
user: system
password: manager
database (a TNSNAME entry):
Connecting to the database...Connecting...
connected.
Hello World
Your JDBC installation is correct.
null

Help please? problems with screen resolution & external monitor

had a look around this forum and seen many questions about screen resolution when connecting to an external monitor but unfortunately, non that help me answer my problem.
got a brand new macbook a few months ago and today bought a HP v220 22" external monitor.
I am new to the idea of external monitors and am unsure what i am doing wrong settings-wise. it seems that no matter what resolution i set either my macbook display, or the external monitor display to. the external monitor is still not sharp.
Im not sure how to explain what i need but basically i need it to be so that things appear on the external the same size as they do on my macbook screen, so that i will have more space to work in on my external monitor (i am a graphics student) but at the moment what appears on the monitor is lieterally just a magnified version of my macbook screen, hence it lacks clarity.
the highest resolution offered in the menu for my macbook screen is 1280x800 and my external is recommended to be set at 1680x1050.
what settings should i have to get the resolution right?
i will be so so grateful if you can help. i think ive tried every single display setting but to no avail. so please help me!

The 13.3" screen on the MacBook running at 1280 x 800 will have a ppi (pixels per inch) of around 113. A 22" monitor running 1680 x 1050 will have a ppi of around 90. So it is natural that it will look magnified compared with the MacBook. The two displays have different a pixel pitch.
Since there are no monitors with ~113 ppi out there in the market, what you want to do with having the same size and sharpness between the MB and a monitor will not be possible.
If you ran the MB's screen at 1024 x 640 (not even sure if that is an available choice), then the two screens would match in terms of "magnification." But the MB isn't going to look very sharp running such a low, non-native format.

Help please - template problems

2 questions please - actually:
1. Dreamweaver CS4... I think my template functionality has somehow become corrupted. When I try to create new templates (regardless of which site I'm trying it within), they look ok. But when I then try to create a new html page using the template, it garbles the format. I tried it every way I can think of... I tried the 2 column fixed, the 3 column hybrid, etc. etc. And I tried them as is in dreamweaver (without adding any formatting or anything... just create a new, save it, and then create a new page using the tempalte). Still the same garbled end results. (it's keeping the spry menu bar, but loses the columnar format and places them on top of each other)
Interestingly, it's only happening with new templates. (what started this was that I have a 2 column template I'm using, and I want to switch to a 3 column). As long as I keep using the existing format with the existing templates, the new pages are ok.
I tried re-installing dreamweaver, and that didn't fix it. Any ideas?
2. I noticed in another post, that there were comments about largers sites don't do well with templates. My site's content based (www.howtogardenadvice.com) with no fancy bells or whistles... but am well over 50 pages, and still growing. Does that mean I have to stop using a template?
Thanks so much for your help!

2. I noticed in another post, that there were comments about largers sites don't do well with templates. My site's content based (www.howtogardenadvice.com) with no fancy bells or whistles... but am well over 50 pages, and still growing. Does that mean I have to stop using a template?
When you site becomes as large as yours sounds, the initial decision to use Templates becomes tedious, since each saved Template change requires that you upload ALL affected local files to reflect that change. As the site becomes larger and larger, this requirement becomes more and more tedious. It's not that the Templates don't work.
I still use Templates on nearly every site I build, but I also use server-side includes to minimize this need. I use the following scheme....
First, I mentally separate the page layout into three sections:
1. Stuff that will not change for the life of the site (i.e., the basic
structural elements)
2. Stuff that *could* change from time to time (e.g., navigation elements,
burst advertisements, section-specific navigation, etc.)
3. Stuff that *will* change from one page to the next
Then I create a Template containing all class1 elements. Next I create
server-side include files containing all class 2 elements and place them on
the Template as needed. Note - some of the class 2 elements may be
"section-specific elements", and their placement on the Template will be
subject to the next item. Finally, I insert editable regions to cover the
class 3 items, INCLUDING the section-specific navigation.
This allows me to just cookie-cut the rest of the site. I estimate that
even for fairly large sites, about 80% of my work goes into planning and
creating this Template file.
To say anything about your #1 problem, we'd need to start by looking at the code on your Template page, and comparing that to the 'garbled' code on your child pages. Can you show us?

Help Please: Playlist Problem

I recently backed up all the musics and movies I had by using the back up disc feature. I used 4 blank dvd discs to back up all of my files. After I transfered my music to another pc I use, I found very disturbing fact. My ipod has all playsits I had before, but itunes doesn't have any playlist. Every music is under the music fold. Since I have about 1500 musics, I can't even imagine to update all playlists manually. I thought that using the back up disc feature would automatically transfer all my playsits. Is this the way supposed to work or I need to change some other settings too? I don't really know what to do. Please help me to solve this problem. I'd really appreciate it.

Welcome to  discussions!!!
Backup just backs up the music. It doesn't back up any of your settings.
Are you using an external HD?
If so;
Hold down the shift key the next time you launch iTunes. Select create library on the pop up window, and save it on your HD.
The next step can be done in a couple of ways.
1. Go to your music folder>iTunes>iTunes Music>right click>send to>navigate to the newly created library and select choose (or whatever windows says)
2. Open your internal iTunes library (hold down shift key>choose library>navigate to your internal music folder>iTunes>choose) Go to iTunes preferences>advanced>general. Change your iTunes music folder location to the location of the new library on your HD: Ext. HD>iTunes> Now go to advanced and consolidate library. You'll get a message that says "consolidating your iTunes library will copy all of your music to the iTunes Music Folder." Select Consolidate
or....
3. Open your newly created library, file>add to library>navigate to the iTunes Music folder on your internal HD and select choose.
There are a couple of other ways, but this should be good.

HELP;;PLEASE,,,,BIG PROBLEM

Hallo,, I'm new in this forum,,
I need an help for a big problem,
suddenly after having download a big image from an email of a friend,,my IMAC is not able to connect to web pages with any browser,,but the line is working because the mail is working in this mac and everythings works with other PC connected at the same router.
then I tried to reinstall Panther from original disc,,,and now is worste then before because many softwear doesn't work if I don't update the 10.3 to 10.3.9 (as I had before the reinstall) but I can't do that because it is impossible to access to any web site,,,
I don't know what to do,,
someone has any idea and can help me???
thanksss,,bye bye
Mac OS X (10.3.9)
Mac OS X (10.3.9)

inapalm:
Let's start with the attempt to re-install.
1. Did you make a backup of all you can't afford to lose?
2. What install option did you use to re-install?
3. After the re-installation, does everything except the internet work properly?
4. What browser are you using?
While I await your response tot he above, try this:
Boot from your Panther install disk holding down the "C" key.
Go to the Installer menu and launch Disk Utility.
Select your HDD (manufacturer ID) in left panel and First Aid in main panel.
Click on Repair. If Disk Utility reports no errors, quit DU.
If DU reports errors click Repair again and again until DU reports the disk has been repaired.
If DU reports errors it cannot repair you will need to use a utility like Tech Tool Pro or Disk Warrior
Good luck.
cornelius

HELP. Connection Problems!!!!!!!

i have just installed the new itunes and when i doubel click to load it up a box comes and says " Itunes has encountered a problem and needs to close, we are sorry for the inconvenience" Please Help.
220 emachines Windows XP

I recently had the same problem following the 10.4.4 update, and was told by DW tech support that there were a number of reported issues with the DW 8.0.1 update. If you're using that you might try rolling back to 8.0. Also, watch out when deleting the DW8 files before reinstalling. There were prefs all over the place: /Library/Preferences, /Library/Application Support, ~/Library/Preferences and ~/Library/Application Support, possibly others. FWIW my problem ultimately was traced to an illegal (for DW, not OSX) character in a recently renamed HD. It was weird, 'cause I had no trouble with DW7, Transmit or Fetch, just DW8.

Help please connection keeps dropping!

Hi, so over the past weeks, days etc ive lost count! My connection keeps dropping. Was using the bt home hub 2.0 was getting all sorts of errors. After getting fed up my dad brings home a homehub 3.0 type b which got given to him brand new by a friend. So installed software etc using adsl by the way not infinity, over the past week the errors from the homehub 2.0 have gone but not this is popping up: 22:43:21,16 Jun. WAN Auto-sensing detected port DSL
22:43:21,16 Jun. WAN Auto-sensing last connection port: DSL
22:43:18,16 Jun. WAN connection WAN3_TR069_INTERNET_R_ATM1_0_38 connected.
22:43:18,16 Jun. PPP IPCP Receive Configuration ACK
22:43:18,16 Jun. PPP IPCP Send Configuration Request
22:43:18,16 Jun. PPP IPCP Receive Configuration Reject
22:43:18,16 Jun. PPP IPCP Receive Configuration NAK
22:43:18,16 Jun. PPP IPCP Send Configuration Request
22:43:18,16 Jun. PPP IPCP Receive Configuration Reject
22:43:18,16 Jun. PPP IPCP Send Configuration ACK
22:43:18,16 Jun. PPP IPCP Receive Configuration Request
22:43:18,16 Jun. PPP IPCP Send Configuration Request
22:43:18,16 Jun. PPP CHAP receive success: authentication ok
22:43:18,16 Jun. PPP CHAP Receive Challenge
22:43:18,16 Jun. PPP LCP Receive Configuration ACK
22:43:18,16 Jun. PPP LCP Send Configuration Request
22:43:18,16 Jun. PPP LCP Receive Configuration Reject
22:43:18,16 Jun. PPP LCP Send Configuration ACK
22:43:18,16 Jun. PPP LCP Receive Configuration Request
22:43:18,16 Jun. PPP LCP Send Configuration Request
22:43:16,16 Jun. QoS Rate cap set to 1.1Mbs
22:43:15,16 Jun. WAN connection WAN1_INTERNET_B_ATM2_0_35 connected.
22:43:15,16 Jun. DSL Link Up: Down Rate=18211Kbps, Up Rate=1071Kbps; SNR Margin Down=6.1dB, Up=6.4dB;
22:43:06,16 Jun. Client associated: IP 192.168.1.71, MAC 50:B7:C3:FD:26:29, host touchedbythehandofgod, Link Rate 72.2 Mbps
22:43:00,16 Jun. HTTP User admin login from 192.168.1.64 successfully.
22:42:49,16 Jun. HTTP User admin from 192.168.1.64 login failure.
22:42:35,16 Jun. WAN connection WAN1_INTERNET_B_ATM2_0_35 disconnected.[ERROR_NO_CARRIER]
22:42:35,16 Jun. HTTP User Basic login from 192.168.1.64 successfully.
22:42:33,16 Jun. PPP LCP Send Termination Request
22:42:33,16 Jun. OpenWiFi tunnel down
22:42:31,16 Jun. WAN connection WAN3_TR069_INTERNET_R_ATM1_0_38 disconnected.[ERROR_NO_CARRIER]
22:42:31,16 Jun. DSL Link Down:the duration is 35 seconds [1 : LosDetector]. Can some one please help I'm not the account holder and my mum will not call bt as I'm sure as lots of people know the India call center are not the best, my mum is account holder by the way sorry about how this has come out I'm writing this off my iPhone as the connection has dropped a lot today. Any help is appreciated many thanks.

Hi Welcome to the community forums
Here is a basic guide to getting help from the community members done by CL Keith Please read through the link posted http://forumhelp.dyndns.info/speed/first_steps.html
once you have posted the information asked for then the community members can help you more
Thank You
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Could someone Help please BlueJ Problem

Ok I am a University Student, and I am at the moment learn Java, as part of my work I have to make a sun descend like the sunset
I have wrote the method, and got it to work, at the moment though I havent gotten it to loop, and I do not know the command for looping, could someone please tell me the command so I can add it to my program.
The program I am using to write this is called BlueJ
Edited by: Devilslore on Oct 7, 2007 12:55 PM

Devilslore wrote:
I have wrote the method, and got it to work, at the moment though I havent gotten it to loop, and I do not know the command for looping, could someone please tell me the command so I can add it to my program.You should go to the Sun basic java tutorials on loops. Have a look here at the for loop tutorial:
http://java.sun.com/docs/books/tutorial/java/nutsandbolts/for.html
The general tutorial index is here:
http://java.sun.com/docs/books/tutorial/java/index.html
The program I am using to write this is called BlueJThis has nothing to do with your problem. It is a tool to help you write java, nothing more. The program you are really using is the java compiler. In fact, in your next post here, consider having a better subject header. The one you listed suggested that this was an IDE (Integrated Development Environment) problem rather than a simple java problem. By mislabeling this header, I will bet that you cut the number of folks reading your question by more than half.

HELP PLEASE - BASIC PROBLEM

Hi, I am a beginner and am stuck on a problem. Maybe you guys can help me out...
"The intersect method computes the intersection of 2 rectangles--that is, the rectangle that is formed by 2 overlapping rectangles. You can call this method as follows: Rectangle r3 = r1 intersection(r2);
Write a program that constructs 2 rectangle objects, prints them, and then prints their intersection"
Thanks,
RM

I am still having trouble with this...and I cannot figure out why. I entered the following:
public class Sect
{ public static void main(String[] args)
{ Rectangle r1 = new Rectangle(10,10,40,40);
Rectangle r2 = new Rectangle(20,20,40,40);
Rectangle r3 = r1.intersection(r2);
System.out.println(r3);
I came up with the following errors:
Sect.java:5: cannot resolve symbol
symbol : class Rectangle
location: class Sect
{ Rectangle r1 = new Rectangle(10,10,40,40)
^
Sect.java:5: cannot resolve symbol
symbol : class Rectangle
location: class Sect
{ Rectangle r1 = new Rectangle(10,10,40,40)
^
Sect.java:7: cannot resolve symbol
symbol : class Rectangle
location: class Sect
Rectangle r2 = new Rectangle(20,20,40,40);
^
Sect.java:7: cannot resolve symbol
symbol : class Rectangle
location: class Sect
Rectangle r2 = new Rectangle(20,20,40,40);
^
Sect.java:9: cannot resolve symbol
symbol : class Rectangle
location: class Sect
Rectangle r3 = r1.intersection(r2);
^
5 errors
PLEASE HELP!!
thanks,
GM

HT201263 Help please! Problems with iPhone 4 after iOS 6 upgrade

Tried to upgrade iPhone. Got a message saying settings were lost, connect to iTunes. I did this and it said I had to restore. I did this and it said unable to restore due to unknown reason. Now phone keeps trying to upgrade and then restarts. iTunes doesn't recognise my phone.
I have tried all troubleshooting tips and nine work!
Please help!!

same here..it doesnt work for me too!!
exactly same issue. Apple got something wrong with iOS 6

Help please, connectivity problem

Similar Messages

Maybe you are looking for