Help - WRT54G v8 blank web setup screens

My new WRT54G works fine except that after accessing the web setup menus (via a wired connection) at some point I start getting blank screens. I'm still able to access the router (there's no timeout error), but all of the pages, including ones I've been able to access before, are blank.
Internet access to other sites continues to work fine. Power cycling or resetting the router makes the problem go away temporarily, but it always comes back when I access a large number (10-20 typically) of the router setup pages.
I've tried restarting the browser, using a different browser, clearing the arp table on my pc, releasing/renewing DHCP, and reflashing the router firmware.
Has anyone seen this before? Any suggestions?
Chuck
new to Linksys, but lots of network experience
WRT54G V8 with 8.00.0 firmware

I've checked the IP settings and they're O.K. I'm using a static IP address. Everything works fine for a while. I can access the net, I can access my LAN, and (initially) I can access the router setup pages.
The problem starts when I browse from page to page on the setup menu. After ~10-20 pages, they start showing up blank. The pages continue to load, there's just nothing in them. Examining the html shows they are empty, not just not being loaded. Surfing to other pages on the net or the LAN continues to work just fine.
It sounds weird, but if anyone has seen this, they'll know what I'm talking about.
Update: Search this forum for "blank page" or "blank pages" and you'll find quite a few users with similar problems. The only fix I've found is to power cycle the router, and that's just a temporary fix.Message Edited by cel on 05-01-200705:44 AM

Similar Messages

WRT54G version 6 - router setup screen via Internet Explorer 7 doesn't display correctly

Hi,
I've just set up my WRT54G router. I'm able to connect to the internet and I'm able to connect directly to the router via IE but the setup screen doesn't display correctly. I've tried resetting the computer and updating the firmware but it still doesn't display correctly. Almost all of the text is missing except for the Linksys logo and a few drop down menus. Any help/suggestions would be great, thanks.

Hi gang,
There a number of things that you can do to solve this problem but most of them involve changing the rules that you have already configured in your ZoneAlarm profile. My preferred solution is to:
-unplug your router from the WAN (why not?)
-turn off zone alarm
-access your router's administration page at http://192.168.1.1
-find the admin page where you can switch admin access from http to https
--- **save your changes !!**
-reboot your router
-plug the WAN cable back into your router
-turn ZoneAlarm back on
-access your admin page at https://192.168.1.1 ( note the 's')
Bob is your sister's brother! Your admin page should work as it is supposed to. Your router and ZoneAlarm should be playing nicely together. You haven't borked your finely tuned zonealarm rules. You were going to bookmark your admin page anyway, and if you want to allow remote administration, you would want to use https anyway. Nothing is broken and you fixed two things. "Its a good thing."Message Edited by ubuibi on 12-27-200609:10 AM
There are really only 10 kinds of people in the world;
Those who understand binary and those who don't.
ubuibi

Unable to access web setup from 4 different Win7 machines with IE9 / FireFox

I Hope someone can help, I suspect this may have something to do with a recent update to Windows or IE since this worked at least a couple of months ago.
I'm unable to access the web setup screen from 4 different windows machines running IE 9 or Firefox (various combinations of wireless, wired, etc.). When I get to the certificate error and hit the "yes, i understand, continue", it comes back with a 'can't be reached' page and looking into the details says the 'connection was dropped'. However If I connect from a MacBook / safari, I'm able to reach the page fine (and admin the router).
Summary:
Using a wrt610n
I am connected to the router, the ip address hasn't changed, the password hasn't changed
I can use the router & connect to the internet
I have the router set to require HTTPS, but switching it to allow HTTP doesn't help.
Both Wired & Wireless Win 7 / IE9 machines can't connect.
Tried setting the router ip address to 'trusted' zone in IE
Tried setting the router ip address to the 'compatibility' mode in IE
Tried using latest version of Firefox with the same results.
Thanks in Advance!
Stephen

Before I suggest you any troubleshooting steps, I would like to ask few question. Like did you try opening the “https://192.168.1.1” in Internet Explorer 8. If not, then try to open the Router Management page in the same manner in Internet Explorer 8 and check whether it opens or not. As it should show up.

Wrt54g web based setup screens

After entering my password for my router, the basic setup screen
displays, but there are no buttons shown for Wireless or other options.
I can't get to any of the other configuration screens.
I get the same results with IE7 and Firefox V3.
The router functions ok but I can't make any configuration changes to
the router.

To view the router's web pages:
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Check to see if your "modem-router" is using the same 192.168.1.x address space as your Linksys router. If it is, then report back with this problem, and also state the make and model of your modem-router.
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. The router's setup pages should work, however, you will need to setup the router again from scratch.
If the reset does not fix your system, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

How to Setup Forward Error Handling in PI Scenarios. Can you help me with the same with screen shots if possible?

Dear all
How to Setup Forward Error Handling in PI Scenarios. Can you help me with the same with screen shots if possible?
Thanks
Regards
karan

Hello
These are the following errors
1. Trace level="1" type="T">no interface action for sender or receiver found</Trace>
2. <Trace level="1" type="System_Error">Application-Error exception return from pipeline processing!
3.
<Trace level="1" type="T">Application Error at Receiver... => ROLLBACK WORK</Trace>
<Trace level="1" type="T">System Error at Receiver... => ROLLBACK WORK</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST" />
<Trace level="1" type="System_Error">Application-Error exception return from pipeline processing!</
Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>Trace level="3" type="T">Error of the prevous version:</TraceTrace level="3" type="T">Error ID APPLICATION_ERROR</Trace>
tThere are repeating errors also.
TThanks
Regards
kkaran

Can't remember how to enlarge web browser screen on OSX 10.6. Can anyone help?

Can't remember how to enlarge web browser screen on OSX 10.6. Can anyone help?

Hi ..
Click and drag out the bottom right corner of any Safari window.

Installing Reader or Flash player on Windows 7 and I get a blank command prompt screen that does nothing. Help please.

Installing Reader or Flash player on Windows 7 and I get a blank command prompt screen that does nothing. Help please.

Try using the offline installers.
Adobe Reader: http://get.adobe.com/reader/enterprise/
Flash Player for Internet Exporer - ActiveX
Flash Player for Firefox - NPAPI

Dear apple management, I have purchased I pad mini e few days ago. I need help as follows: (1) Camera: i did take a few photos but something has gone wrong. As i press the camera icon, I get a blank dark black screen. What do you think has gone wrong ?

Dear apple management, apple support communities
I have purchased I pad mini e few days ago. I need help as follows:
(1) Camera: i did take a few photos but something has gone wrong. As i press the camera icon, I get a blank dark black screen. What do you think has gone wrong ? HELP URGENTLY REQUIRED.
(2) How do i sync my pc with I pad mini?
(3)i can read on i pad mini file made in microsoft excel but all numbers are very different from the original document. What is the solutuon?
Dr Uma S Nayak
<Personal Information Edited by Host>

You are talking to fellow users on these forums, not iTunes Support or Apple - I've asked the hosts to remove your phone number from your post.
For the Camera app, try closing it via the taskbar and see if it works when you re-open the app : from the home screen (i.e. not with the Camera app 'open' on-screen) double-click the home button to bring up the taskbar at the bottom of the iPad's screen, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Camera app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
If that doesn't fix it then try a soft-reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
In terms of syncing, you will need iTunes on your computer - if you haven't already downloaded it then you can do so from here : http://www.apple.com/itunes/download/
You can conncet the iPad to your computer and select it on the left-hand sidebar of your computer's iTunes (you can enable the sidebar on iTunes 11 on a PC via control-S), and use the tabs on the right-hand side of the iTunes screen to sycn your content to the iPad.
Syncing music : http://support.apple.com/kb/HT1351
Syncing apps : http://support.apple.com/kb/PH12315
If you haven't yet synced your iPad to your computer you may also find this page useful : https://discussions.apple.com/docs/DOC-3141
For the excel file, what app are you viewing/editing it in ? If the values are different then it may be that the app that you are using doesn't support all the formulas that are being used in the spreadsheet. Apps that 'support' excel documents include Apple's Numbers app, and from third-parties apps such as Documents To Go ('premium' version) and QuickOffice Pro HD.

I have tried multiple times to install CC and muse only getting blank creative cloud screen (no error and in serious pain in the butt to uninstall) PLEASE HELP!!!!!!

I have tried multiple times to install CC and muse only getting blank creative cloud screen (no error and in serious pain in the butt to uninstall) PLEASE HELP!!!!!!

Geekysmooth please try the steps listed in Creative Cloud app doesn't open and hangs on spinning progress wheel - http://helpx.adobe.com/creative-cloud/kb/creative-cloud-app-doesnt-open.html to resolve the current error which you are experiencing.

Stuck at wireless setup screen on start up - HELP!

I have just bought a macbook ... i have turned it on and got through to the wireless network setup screen ... however i do not have a wireless network! how do i get past this screen without selecting a network!? please, please help!

Sorry i was being stupid... found the button that said 'i do not have a wireless network'! lol
sorry! what a noob!

I've signed up for MobileMe but when I sign in again to find my iPad I'm brought back to the setup screen and I can't get this this to get around Setup! Help!!

This group screen is infuriating. Why do I have to post my question twice?!?!
I registered for MobileMe, but when I go to www.me.com I'm brought back to the setup screen and I can't get past it. How do I get to the site that allows me to find my iPad?

How do I get to the site that allows me to find my iPad?
You go to http://me.com/find/ on your computer.
On your iPad, you use the free Find my iPhone app from the AppStore.

My ipad is stuck on puffin web browser screen please help cant turn it off

my ipad is stuck on puffin web browser screen and i cant turn it off how do i restart or reboot it thanks

Reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.

Need help accessing the router web page. I have been tol...

Need help accessing the router web page. I have been told my router is acting like a switch and the IP address is not in the proper range. I have tried reseting the router (hold for 30 sec and unplug for 5 mins). Didn't work.
thanks

What router are you using? Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS (not the WRT54GS).
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 01-21-2008 04:40 AM

Web dynpro screen with multiple rows with columns that can be edited

Web dynpro screen with multiple rows with columns that can be edited individually:
Hi
I am busy creating a screen in web dynpro for ABAP which we would like to make available via Portal ESS (Portal 7).
I need to add 'n type of table (or almost something like Excel) or something in which someone can type a few paycode numbers (there should be lets say 10 blank rows in which info can be typed in and if I click on a button or so, more rows must be added if necessary. Then in the other colums stuff like amounts must be entered which one should also be able to edit then and there.
Can anyone assist in what I can use for this? There does not seem to be some existing element that I can use.
Help will be appreciated.
Regards
Debbie

Hi Debbie,
Whiel Creating table you need to be care full that use chose INPUT FIELD as the CELL EDITOR. Just guessing that if ur table is not editable u might have choosen TextView as default cell editor type.
check link for details on TABLE UI
[http://help.sap.com/saphelp_erp2005/helpdata/EN/b5/ac884118aa1709e10000000a155106/frameset.htm]
easy way is to first add UI ELEMENT TABLE to your VIEW, then right click over it & select create binding from context. After you have a pop up where you can select what columns you want what should be its cell editor etc.
Greetings
Prashant

Setting up context sensitive help for WebHelp in web application.

Hi,
I'm working on a help system for a web application. It will include context sensitive help triggered by an icon on the screen, and the Topic will open in an iframe with a set size. The developer has already set up the iframe that pops up when the icons are clicked. He is giving me the ID for the screens with the help icons as a fully qualified java file name. I'm not sure what the correct process would be in RoboHelp to map the ID's to the topics.
1. Do I create a map file using the list of ID's the developer sends me? Would it be in this format:
#define Topic_Name Java_File_Name
2. Do I then add the ID to the appropriate help Topic using Project Setup pod Context-Sensitive Help folder?
3. When I generate the layout I specify the map file I created above (.h extension)
3. If the developer already set up the iFrame size, is it correct that I don't need to create a custom window to set up the size? Is there a way to set it so two panes open? (I believe using the method above one pane opens with link to navigation pane)
Thanks in advance,
Joanne

Welcome to our community
See if the link below helps.
Click here to view
Cheers... Rick
Helpful and Handy Links
RoboHelp Wish Form/Bug Reporting Form
Begin learning RoboHelp HTML 7, 8 or 9 within the day!
Adobe Certified RoboHelp HTML Training
SorcerStone Blog
RoboHelp eBooks

Help - WRT54G v8 blank web setup screens

Similar Messages

Maybe you are looking for