Home Hub 3 Access Control not working

Not sure if anyone can help with this, but here goes!
I have access control enabled on my HomeHub 3 which should stop my daughter from using the Internet between 9:00pm and 3:00pm - it seems to be working in as much as she isn't able to access the internet from her laptop from the time she gets up until 3:00pm, but it doesn't stop her using the internet at 9:00pm, in fact she can still quite happily access the internet up until 10:30 or even later.
I have tried restarting the hub, switching access control off and back on and delting and re-instating the device block but none of these seem to work properly, so any advice would be gratefully received.
I'm also having problems with wireless connectivity, but I've put that in a different post as I think it probably needs different expertise

It could be because the time on the hub is an hour slow because it has not updated to BST. This is a known problem which BT were going to sort out within a few days! See here and elsewhere in these forums: http://community.bt.com/t5/Other-BB-Queries/Clocks-Forward/td-p/448429.
Pending resolution of the problem, putting the Access Control times back an hour might do it. (It has been reported that the alternative of setting the time manually can result in the hub not keeping time very well.)  
You can click the white star next to this message if you think it was helpful.

Similar Messages

  • Airport time access control not working for iPhones-

    Hi,
    I use a 3rd generation Airport Extreme base for my WiFi hme network.
    For parental control, I'd like to allow one iPhone and iMac to be connected only for some hours of the day.
    So I have activated the timed access control and entered the relevant MAC addresses and the time to be connected.
    It seems that the iMac is well restricted as it should, but the iPhone has no limitation…
    Why is it not effective for the iPhone ? The iPhone MAC address (Wi-Fi Address) doen't work in this case ?
    (I have Lion up to date)
    Thanks for your help
    Eric

    Sorry, my fault:
    I wrote the Bluetooth adress instead of the WiFi address…
    It works perfectly now for me

  • Access Control not working as expected after upgrade to 7.5.2

    I have a Time Capsule set up with mac address access control on the main network plus a guest network. After the upgrade to 7.5.2, it seems that the access control is applying to my guest network and the main network is allowing all devices on it. Has anyone else seen anything like this and/or know what to do about it?

    I am also seeing this behavior. The workaround is to add all the guest network devices to your ACL. But this is a regression - there isn't much point in having a guest network that requires updating the base station each time a new device joins.

  • SCSM View access control not working

    I have 15 odd each SCSM Incident and SR roles, one for each support group.  Each role contains an AD group, populated with users.  No OTB roles contain any users other than the admin role.
    Each role is granted access to only the views for SR and IM that they need. 
    All the views are stored in one MP, that is one top level folder with all the views inside it.  So when they expand the folder, they should only see the views assigned to the roles of which they are a member.
    However, more and more often, Users are opening their console to find that they see all the views, for all roles.
    Sometime if they shut down the console, and restart it, the views will return to normal.
    But that is starting not to work anymore as well.  And its very odd that it will happen to one user in the role, but not the other users.
    Any ideas?
    SCSM2012 R2
    Joshua Fuente

    Never mind, I did find that they added a group to an OTB role... Removed, Fixed.  Created a new role, and removed the view access....
    Joshua Fuente

  • Access control not enabled

    Hi,
    I have a problem in create user in TimesTen.
    When I write command:
    create user testuser identified by 'test';
    command line give me an error:
    15007: Access control not enabled
    The command failed.
    My ttVersion is:
    TimesTen Release 7.0.3.0.0 (32 bit NT) (tt70_32:17000) 2007-09-19T16:04:16Z
    Instance admin: dominik
    Instance home directory: C:\TimesTen\tt70_32
    Daemon home directory: C:\TimesTen\tt70_32\srv\info
    My OS is Windwos 2000.
    I found advice on this forum but it doesn't work. I tell about doing this command:
    ttDaemonAdmin -stop
    ttuser -init c:\TimesTen\tt70_32\srv\info\ttpasswd -admin dominik
    ttDaemonAdmin -start
    Can anyone have idea how to make access control enable??
    Dominik

    First of all, I want to thank you Chris for so many suggestions :)
    So I answer to your sentences:
    You need to uninstall and re-install TimesTen in order to enable the access control facility.I think that this solution won't help.. I really remember that I check Access Control during the instalation, because I install TimesTen first time and I use viewlet from oracle site for help!!
    Do you have a supported version of the Oracle client installed? Yes I'm sure that both of the system have supported Oracle version (Oracle 10g)
    Is the environment setup properly for the Oracle client? Did the user you were logged in as when you installed TimesTen have a valid Oracle client environment. In 99.99% of cases, this issue is because the Oracle client is not installed or the TimesTen service does not have a valid Oracle client environment.As I said, I install TimesTen with viewlet, so I think that properly setup environment
    Actually, you van enable access control without uninstalling and re-installing. You need to run the command: ttmodinstall -enableaccesscontolI try this command on Windows and that is the result:
    Would you like to enable access control for this instance? [ no ] yes
    NOTE: The daemon must be stopped before enabling access control.
    Would you like to stop the daemon? [ yes ]
    Retrying ...
    Retrying ...
    Retrying ... <- and process doesn't retry :/
    Even if I start this process on Administration Panel -> Services and write command ttVersion in command line, still Access Control is not shown :/
    I try this command on Linux too..
    And this is the result:
    Would you like to enable access control for this instance? [ no ] yes
    NOTE: The daemon must be stopped before enabling access control.
    Would you like to stop the daemon? [ yes ]
    Enabling access control ...
    Patching successful ...
    Restarting the daemon ...
    Warning: library libclntsh.so does not exist at /oracle/10g/lib or /oracle/10g/lib32. Check ORACLE_HOME for proper operation of Cache Connect.
    TimesTen Daemon startup OK.
    Access control is now enabled for this TimesTen instance.
    It look nice, but when I try co connect:
    connect "dsn=ttdemo;oraclepwd=myuser";
    It not work :/
    Can anyone help me now?? Chris??

  • JDBC control not work after upgrade application from workshop 8.1 to 9.2.3

    Hi,
    We upgraded application from workshop 8.1 to 9.2.3. After that, the JDBC control not work any more. We got the following exception:
    java.sql.SQLException: The transaction is no longer active - status: 'Committed'. No further JDBC access is allowed within this transaction.
    at weblogic.jdbc.wrapper.JTSConnection.checkIfRolledBack(JTSConnection.java:192)
    at weblogic.jdbc.wrapper.JTSConnection.checkConnection(JTSConnection.java:202)
    at weblogic.jdbc.wrapper.Connection.preInvocationHandler(Connection.java:87)
    at weblogic.jdbc.wrapper.Connection.getMetaData(Connection.java:435)
    at org.apache.beehive.controls.system.jdbc.parser.SqlStatement.createPreparedStatement(SqlStatement.java:128)
    at org.apache.beehive.controls.system.jdbc.JdbcControlImpl.execPreparedStatement(JdbcControlImpl.java:272)
    at com.bea.wlw.runtime.core.control.internal.JdbcControlImpl.invoke(JdbcControlImpl.java:136)
    at controls.SecurityBean.getUpdateDocPermission(SecurityBean.java:598)
    at security.SecurityManagerImpl.getUpdateDocPermission(SecurityManagerImpl.java:110)
    at security.SecurityManagerBean.getUpdateDocPermission(SecurityManagerBean.java:509)
    The control that throw the exception has "transactionattribute" annotation added automatically by upgrade wizard during upgrading. Related classed are as follows:
    @ControlInterface()
    public interface SecurityManager
    @TransactionAttribute(TransactionAttributeType.REQUIRED)
    boolean getUpdateDocPermission(java.lang.String userId);
    @ControlImplementation()
    public class SecurityManagerImpl implements SecurityManager, Serializable
    * @common:control
    @org.apache.beehive.controls.api.bean.Control()
    private controls.Security security;
    static final long serialVersionUID = 1L;
    * @common:operation
    public boolean getUpdateDocPermission(String userId)
    if ( security.getUpdateDocPermission(userId) > 0) {
    return true;
    else
    return false;
    @ControlExtension()
    @JdbcControl.ConnectionDataSource(jndiName = "EventDesk")
    public interface Security extends JdbcControl
    static final long serialVersionUID = 1L;
    * @jc:sql statement="select r.updateDoc from document_user u ,document_role r where u.login={userId} and u.roleId=r.roleId;"
    @JdbcControl.SQL(statement = "select r.updateDoc from document_user u ,document_role r where u.login={userId} and u.roleId=r.roleId;")
    int getUpdateDocPermission(String userId);
    Thanks for your help

    Hi. The issue is a level or two above JDBC. I suggest
    opening an official support case. It's probably a
    WLW issue.
    Joe

  • SSRS 2008 R2 Calendar Control not working and report not refreshing on pressing enter in Chrome.

    SSRS 2008 R2 Calendar Control not working and report not refreshing on pressing enter in Chrome.

    SSRS reports are always best viewed in IE and the report result what you see in IE always will not be same and consistent in thirdy party browswers.
    So consider using IE as workaround.
    Also please refer:
    https://social.msdn.microsoft.com/Forums/vstudio/en-US/2188de10-cff9-4e24-b14f-da5121f1c4a4/ssrs-calender-control-not-visible-in-chorme-on-server?forum=sqlreportingservices
    Workaround here:
    http://www.rajbandi.net/Fixing-SSRS-Report-Viewer-control-date-picker-in-Google-chrome/
    -Vaibhav Chaudhari

  • HT4623 iOS 6.1 no longer available because you are no longer connected to the internet- this is what my iphone 4 shows. iv tried switching off again and again, closing apps by double tapping the home button but still not working. please help.

    this is what my iphone 4 shows. iv tried switching off again and again, closing apps by double tapping the home button but still not working. please help.
    is there any other method to download ios 6.1.2.
    my phone is not being recognized by itunes on my new windows 8. neither its working on touch copy.
    kindly help.
    thanks

    well in thatcase, i need another help .
    thanks for your instant reply.
    i have currently bought a new laptop (windows 8) and my iphone is not being recognized by itunes.
    because i have no backup on my previous laptop, i downloaded touchcopy but even touch copy is not recognizing my iphone.

  • Alternate Access Mapping not working for Zone : Intranet

    One of our client want to set Alternate Access Mappint (intranet) with url "intranet.theirDomain.com" with local IP address.
    is it possible?
    subsequest to my previous question (
    http://social.technet.microsoft.com/Forums/sharepoint/en-US/3f39711e-301a-40e8-aa7a-855fa2c268b1/alternate-access-mapping-not-working?forum=sharepointadmin )
    I want to ask one more question
    Can we configure "intranet.theirDomain.com" with local IP address for any other zone?
    or
    If there is ".com" within the url then it can't be configured for InTRAnet?
    Thanks
    S H A J A N

    The names for the zones don't matter. You could use the 'extranet' zone for another intranet name if you wanted, the names are just to make it a bit more friendly for beginners.
    What you describe sounds routine, you create a web application with a name, then use an AAM to allow users to access it with a more friendly name. Frequently you end up creating
    http://intranet.domain.com and
    http://intranet as an AAM, or vice versa.
    You can use .com for an intranet site, you would need to add the site as an A Host record in your DNS server so that traffic is sent to your internal server rather than out into the wider world.

  • Sound control not working on my blue tooth keyboard

    sound control not working with my bluetooth keyboard

        UAVPilot,
    Thank you for the information. I do show that the device and car are capable of this function. I do not show any reason you should not be hearing the notifications. One thing you will want to check is that the sound for both your notifications and media are turned up. Also you can look into going into Settings>Apps>S voice Drive Mode> Clear Cache. This should clear any possible bugs in the application. Please keep us updated on this and we can check on other options.
    Thank you,
    TonyG_VZW
    Follow us on Twitter @VZWSupport

  • "Assign access control" not appearing under Essbase in shared services

    Hi Everyone,
    Can anyone point out the reason behind this? This is leading to all sorts of problems. Configuration is as follows:
    App Server: Foundation, EAS, Planning, Reporting, Web Analysis, Workspace on Tomcat
    DB Server: Essbase and SQL Server
    Essbase is on Shared Services mode.
    This is actually very urgent. Would be grateful for any help.
    Thanks,
    Sayantan

    This has been posted in the essbase forum > "Assign access control" not appearing under Essbase in shared services
    Cheers
    John
    http://john-goodwin.blogspot.com/

  • Lower volume button control not working help?

    Lower volume button control not working help?

    If you only restored from backup, restore to factory defaults/new iPod.  If you then still have the problem it is likely a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • Beats audio controls not working

    Using my beats headphones this morning with my MacBook Air and iTunes.  Everything is up to date.  Although today now the audio controls on the cord won't work.  Normally I can pause iTunes or control the volume.  I do this multiple times a day but no go today.
    Is this another 10.10.2 bug?  Illustrator 2014 CC no longer works properly with my external monitor.  I'm getting frustrated with all these bugs.
    Also, in my 'About This Mac' info window, it shows my OS as "135122" instead of "Mac OS X" - I'm sure that's not normal.
    Any thoughts, anyone?

    I did a reboot and repaired permissions, which solved the beats headphones controls not working.
    Still concerned about the Mac OS version display though.  Curious to know if anyone else has that as well.

  • 10g db control not working

    Hi
    In 10g database my db control not working.i m also recreate it but same result using these commands.
    emca -repos create
    emca -config dbcontrol db
    Thanks

    so what is returning this: `emctl status dbconsole` ?
    if it tells that DB Control is running so what you've got when You are trying tu run db console (http://host:port/em/ ) ?
    if it's not runnig type 'emctl START dbconsole' and try again
    anyway, if something doesn't work that there have to be some errors :)
    when you will not get any errors from above look for them here:
    $ORACLE_HOME/HostName_InstanceName/sysman/log

  • The web controls not work(windows phone)

    Hi
    I have a web app.after I make an animation in this page(like a transition page in loading page), the web controls not work more.
    the site is shown but any thing not work like scrolling or tap in links

    Can you please explain more clearly what you are doing and what you need help with? What is your overall scenario, what exactly is your code doing, what behaviour do you expect and how is that different from what you actually see?

Maybe you are looking for

  • Issue Regarding MB5B report

    Hi...... When i am running standard report MB5B to calculatte opening stock and closing stock on the output screen i am getting one table with no data selected and the below screen shot of that MB5B report is attached in this discussion please go thr

  • Saving a reader extended PDF form as read-only

    Before posting this, I've searched for hours in the forums and the internet on how to accomplish this but I just can't find the solution. I've created a simple form in Acrobat and saved it with reader extended attributes so it can be saved by my coll

  • Problems with Flash Video

    OK - I have had intermittent problems with Flash video, basically it gets choppy, usually after about 20 minutes - half an hour of watching - recently this problem has gotten worse - coinciding with a recent system update perhaps? - it's more or less

  • WAD: add new formula / structure element to report run by user

    Hi, I know that there is a possibility to add a formula or "structure element" to a WAD report that is being run by a user (user opens WAD report and can add a formula). We are using WAD 7. Unfortunately I don't know where this function is hidden in

  • Lock Object Doubt

    Hi I have created 10 Shadow tables and will run the job which updates the data to main data base tables. So i am creating Lock Objctects for the tables. Out of 10 tables 8 tables have common key which Business Partner (Primary Key). DO i need to crea