How can I Connect 5 WRT54G V8 routers to cover a large area with Internet?

Hi everybody, can anyone please tell me where can I find documentation with steps to connect many routers at the same time to cover a large area with Internet. I want to connect each router via wireless, so I don't to use hard wire.
Thanks in advance!

Hi Bubbateeth and thanks for your reply,
Right now I have 2 WRT54G version 5 flashed with the DD-WRT firmware and the first one is connected to the internet modem by wire and I setup the second one to receive the internet and send the Internet signal to the first area and is working pretty well, but I'm trying to buy new WRT54G routers version 8 and I don't know if I'm going to have to flash this routers too or if the Linksys firmware can do the job. If it's possible, where can I find instructions to set it up?
Thanks again!

Similar Messages

  • How can I connect the cFP-DIO-550 via a cFP-CB 1 with my circuit

    hi
    I use the module cFP-DIO-550 with a cFP-CB and I do not know how to connect my system with this module, for exemeple I want to connect the gate of a triac with the output 0 is that I need other electronic components or voltage sources.
    thnx for help

    The cFP-DIO-550 can be set to I/O logic levels of 12 or 24V DC.  What kind of voltages are you inputting/outputting?  Check the specifications of this module to see if the connections you're making will be adequate.

  • How can i connect my ipad2 without the 3g chip to another ipad2 with the chip?to another

    I have two ipads2 with 3G, one has a working chip and the other one doesn't.
    I would like to have the one without the chip, connected to the internet through the ipad with the chip, is this possible? How?

    Currently only the iPhone 4 and 3GS have the personal hotspot function (and then only if your carrier supports it) - it's not supported on the iPad

  • HT2477 how can I connect a Garmin GPS etrex vista hcx to macbook pro with retina.

    I would like to know if is it possible to connect my GPS Garmin etrex vista hcx to my macbook pro with retina.
    Thanks.

    I believe that Garmin GPSr model uses a USB connection, so if you load the Garmin drivers, and possibly the [free] Garmin Base Camp utility, you should be able to connect your GPSr to your macbook Pro and transfer information.  I don't recall positively, but I think that your GPSr should appear as a USB drive automatically once you connect it, but it might require you to load the Garmin Communicator software.

  • Does anyone knows how can I connect a PXW-X70 camera, to a PC and stream with Flash Media Live Encoder 3.2? I connect the camera using the USB port, when I launched Adobe only shows my webcam. Thank you.

    Equipment:
    PC - Windows 8
    Adobe Flash Media Encoder 3.2
    Camera: Sony PXW-X70
    Thank you....

    Just guessing, but Windows wont see it unless you have a driver/interface that makes it appear to windows as a video device.

  • Can I connect a WRT54g behind a WAG54g ?

    How can I connect a WRT54G behind a WAG54G ?

    No. It is not really making sense. Why do you want to have a routed LAN? Why do you want a router inside your LAN? A router is a separating network element. It separates distinct subnets. For most home networks this is not what people want. Windows home networking depends to some extent on an connected ethernet network, i.e. a single broadcast domain. A router creates two separate ethernet networks between which you can router traffic. Most consumer routers won't allow you to configure them in a way so that broadcasts will actually cross the router.
    If you have a router inside your LAN you will not be able to do Windows file and printer sharing across the router as you are used to do it in a single subnet. You cannot do workgroup browsing and name resolution across the router without a domain controller/server providing this service for you.
    Also, using software which requires you do "open ports" or configure "port forwardings" are harder to configure because you may have to configure this on two routers.
    Moreover, as you are having two wireless routers: wireless roaming between two separate IP subnets is not possible without reconnection. The client which leaves one access points and moves to the next one must get a new IP address as it belongs now to a different subnet.
    You will only want to operate a real router inside your network if you either have a very big one and with a nice server inside or if there are specific reasons to separate the networks, e.g. when you want to run a server in the internet and at the same time prevent this server to access any other computer as you worry that the server may get hacked and used to access your LAN. Then you can setup a gateway router and connect the internet server to this router. The second router creates a second private LAN inside the first one's. This second LAN is where you connect all your other computers.
    But generally, most home users don't want to run two routers in a home network. They want easy file and printer sharing. They may want to be able to extend the wireless coverage and create a roaming network.
    I hope, it makes sense now why I asked my original question and you can now think more about what you actually want to do with the second router...

  • How can i connect 24VDC to digital input (usb 6008)

    hello,
    how can i connect 24VDC to digital input (usb 6008), is it possible with some optocoupler?
    thanks

    The 6008 is a static DIO, so speed shouldn't be an issue.  Therefore an optocoupler should work.  Just make sure you get one the meets your specs.
    There are only two ways to tell somebody thanks: Kudos and Marked Solutions
    Unofficial Forum Rules and Guidelines

  • How can I connect a audio cassette player to my MBPro to play thru its speakers?

    I would like to play my audio cassette  thru my MBPro. 
    How can I connect it?
    Thanks for your help.
    Vernon

    You are correct.  However, after asking my first question and received your reply, I replied with a second request because my audio cassette player went to the shop and I now wanted to know about a vcr connection.
    And, I have tried your suggestion for the vcr but it did not work for me!! ;-(
    I doubled checked my audio settings in System Preferences to make sure I was using the external mic connection and not the internal mic connection.  Also, I double checked my audio cables and "y" adapters to go from R-L audio output to mini Jack Y-cable and all are working just fine.
    But I do not hear audio thru my MBPro. :-(
    Do you have any other suggestion or question that might help?
    I do appreciate your suggestions and especially your replying to my requests for help.
    Thanks again.
    Oh yes, I need to head to bed since we are on CDT.  So, I will not be able to reply to you until Thursday!
    Vernon

  • I installed an airport card in my powermac g4, how do I connect to my router (not an airport base.) How can I connect to my router?

    I have a powermac g4 quicksilver in which I have installed a normal airport wireless card in the dedicated slot. How can I connect to my router? It is not an apple airbase station but does it need to be? How can I connect to my router?

    What encryption is the Rouer using? If WPA2 you likely can't.
    Go to System Preferences
    Click Network
    Highlight AirPort and click Configure...
    What shows for Routers there? Or is Join Other Network availabe in 10.3.x?

  • How can I connect my 3gen apple tv with HDMI to my bush LCD32TV022HD which does not have an HDMI port but does have 1)S-Video I/P, 2)Video I/P, 3) L

    How can I connect my 3gen apple tv with HDMI to my BUSH LCD32TV022HD
    This does not have an HDMI port but does have:-
    1) S-Video I/P,
    2) Video I/P,
    3) Audio Input (Left & Right)
    4) Audio In jack (for VGA and DVI source)
    5) DVI input
    6) VGA input

    Welcome to the Apple community.
    The Apple TV doesn't officially support a DVI connection, however you may be able to get it to work. You will first need to check that your TV supports either 720p or 1080p as well as HDCP. If you are able to get the video working over the DVI connection, you may also require a DAC in order to connect with Apple TV's optical audio output to the TVs audio imput.
    You may well wish to make sure that the DVI connection works before spending any money on a DAC..

  • How can i connect to SQL Server 7.0 on Windons Using JDBC

    How can i connect to Microsoft SQL Server 7.0 on a windows enviroment ?
    in sql server 2000 some jar files are required that is
    What you need to do is actually add all three jar files to your class path individually. There are three jar files that come with this driver the msbase.jar, msutil.jar, and mssqlserver.jar. for sqlQ server 2000.
    now the problem is that i cant find these files on my system. firstly where these files will be located. secondly are they will be used to connect to SQL Server 7.0. thirdly if not what is the procedure.
    My next Problem is that I have Websphere Studio Application Developer. in which their is this facility of Database Webpages its like a wizard which makes automatically beans servlets and JSP but before that you need a Driver Name and and Class Name for to Connect to the Database.
    Can you tell what is the specific Driver Path for the Microsoft SQL Server 7.0 . secondly is this the class which is used to connect to SQL server 7.0 "com.microsoft.jdbc.sqlserver.SQLServerDriver" where can i find this one. for SQL server 7.0.
    please provide some guidance in this regard.

    You can search for the JDBC drivers at, http://industry.java.sun.com/products/jdbc/drivers
    All the three jars that you specified are part of MsSQL Server jdbc driver. You need them (in the classpath) to get connected to the database.
    "com.microsoft.jdbc.sqlserver.SQLServerDriver" is the class in mssqlserver.jar. This is the driver class which will be used to get connected to the database.
    You can search in this forum for writting jdbc code (for Sql Server). If you don't find these jars, give me your e-mail id.
    Sudha

  • How can I connect to SQL Server CE?

    Hi!
    How can I connect to SQL Server CE ?
    Any idea?
    I found jdbc driver for SQL Server 6.5,7.0,2000.
    But no driver for SQL CE.
    Thanks for any suggestion....

    I am also searching for same answer.
    I wanna choose Access as a db. but I can't find that so I have a no choice to select SQL2000CE though.
    I am stuck in driver problem. I can't find that.
    Should I use Oracle Lite or PointBase?
    I am under a lot of stress... like you've been...
    I wish you find and post that....

  • How can I connect my iMac to a TV for playback of videos? My TV does not have HDMI.

    How can I connect my iMac to a TV for playback of videos? My TV does not have HDMI.

    You need to find out what video out you have on your iMac, and what kind of video inputs there are on your TV.
    It will help to know exactly what model iMac and exactly what make/model TV you have.
    Depending on the exact model iMac you have, it may have miniVGA, miniDVI, miniDisplayPort or Thunderbolt output.  Your TV may have composite, S-video, component, DVI, VGA or HDMI inputs.  Once you confirm what kind of ports your iMac and TV have, then we can probably suggest the correct cable or adapter so you can connect them to each other.

  • How can I connect my Powerbook or iPad Retina via HDMI cable to 4K digital video camera to be a "control monitor"

    How can I connect my Powerbook or iPad Retina via HDMI cable to 4K digital video camera to be a "control monitor"

    That won't work with the iPad, unless maybe there's a "control monitor" app somewhere.

  • How can I connect my TV sony bravia to Imac for display !

    How can I connect my TV sony bravia to Imac for display ! I did it before but a week ago crash my sistem and been to apple store london to fix it and wend I come home I can not reconnect the tv to imac ! please help !!!!!!!!!!!

    I BUY A CABLE FROM AMAZON.CO.UK AND MY iMAC WAS WORKING WITH THIS CABLE BUT AFTER THEY (APPLE STORE REGENT STREET ) REPARIT NOW IS NOT RECONICE THE DISPLAY !!!!!

Maybe you are looking for