How do i get the CPU to run at full speed steadily?

how may I get the S10's CPU to run at the full speed (near 1.6GHz) steadily?
since the power scheme's fixed to be "Lenovo" and is only adjustable through its own energy management
I'm not able to set the power scheme as "Always On" like how I may do with other laptops
I tried changing every option possible and found no way I could stop the CPU from constantly reducing its speed to half
it keeps going back and forth between 1.6 & 0.8 GHz 
how may I possibly get this fixed up? 
I'd like to have my CPU always run at the full speed when plugged in 
thanks a lot

eggimage wrote:
thanks
but i've tried adjusting the frequency too
it is set to the highest frequency by default and still isn't stable
what program do u use? try cpuz, www.cpuid.com
EDIT: i also want to ask, why do u want to lock the cpu to 1.6ghz? it will not make any noticable difference in performance, will just keep the vcore high, resulting in high temps, and louder fan..
Message Edited by nagatyh on 04-05-2009 06:43 PM
AMD Phenom II X6 1055T / 2xATI HD5770 CF / 8GB DDR3 / 4x500GB RAID-5 / Win 7 Ultimate x64
Lenovo S10e Black / 2GB DDR2 / 160GB HDD / 6-cell battery / Win 7 Ultimate x86
Motorola Xoom

Similar Messages

  • I am using a timed while loop and am unable to get the loop to run at a speed of less than 1ms (I am currently using the Wait(ms) function). How can I get a faster response?

    I am trying to create a virtual engine within a timed while loop and am unable to get the loop to run at a speed of less than 1ms (I am currently using the Wait(ms) function). This does not however allow realistic engine speeds. How can I overcome this? I have access to a PCI-MIO-16E-4 board.

    andyt writes:
    > I am using a timed while loop and am unable to get the loop to run at
    > a speed of less than 1ms (I am currently using the Wait(ms) function).
    > How can I get a faster response?
    >
    > I am trying to create a virtual engine within a timed while loop and
    > am unable to get the loop to run at a speed of less than 1ms (I am
    > currently using the Wait(ms) function). This does not however allow
    > realistic engine speeds. How can I overcome this? I have access to
    > a PCI-MIO-16E-4 board.
    Andy,
    Unless you use a real time platform, getting extactly 1 ms loop rate
    (or even less) is impossible. It starts getting troublesome at about
    0.1 Hz for standard operating systems.
    I'd tackle your problem with "if i mod 10 == 0 then sleep 1 ms".
    Of
    course this is jerky by design.
    HTH,
    Johannes Nie?

  • HT1725 I have a few songs that will only play for about a min the it will stop playing how can i get the songs back to a full song

    I have a few songs that will only play for about a min the it will stop playing how can i get the songs back to a full song

    Depending upon what country that you are in (music can't be re-downloaded in all countries) then try deleting the incomplete tracks from your iTunes library and redownload them via the Purchased link under Quick Links on the right-hand side of the iTunes store home page on your computer's iTunes : re-downloading.
    If you aren't in a country where you can re-download music or if they re-download in the same state then try the 'report a problem' link from your purchase history : log into your account on your computer's iTunes via Store > View My Account and you should then see a Purchase History section with a 'see all' link to the right of it ; click on that and you should see a list of your purchases ; find those songs and use the 'Report a Problem' link.

  • I have a dual 1.8 ghz pwer pc g5 and sometimes i put it in sleep mode and come home on my lunch break and the fan is running at full speed and the computer has frozen up...what is going on here?

    and sometimes i put it in sleep mode and come home on my lunch break and the fan is running at full speed and the computer has frozen up...what is going on here? is it a virus or has my computer been hijacked? it cant be good for the computer...anyone ever had this problem..?

    Your problem has been reported many times, but causes are as varied as individuals.
    Can we assume that a hard shutdown allows a normal restart?
    Can I assume that you have used Disk Utility from your OS X install disc to repair the hard drive directory? The freezes and hard shutdowns require that the drive be repaired (not permissions) or soon the machine won't boot at all.
    If the root issue is software related, in Console (the application) under Logs, there should be loggings around the time of sleep and logs that tell you what process went wild and froze the machine.
    Network activity is also a common casue.
    Other info:
    http://support.apple.com/kb/ht1776
    If hardware related, such as an external drive, other USB device (Wacom tablet) or USB PCI card, ejecting, disconnecting, removing, or in the case of the Wacom, updating drivers, are all potential remedies.

  • How Can I Get The Cpu State With Java?

    are there any method to use??
    what's more,I also wanna to know how can I get
    the current ram that the System is using
    and the threads the System are running?
    Will you please share your knowledge here or
    write to tell me at [email protected]?
    Thanks!!

    if you know how to do this in c++, you can write native methods and use them in java.
    native methods forum:
    http://forum.java.sun.com/forum.jsp?forum=52
    tobias

  • How do we get the plugin to run and not crash flash and shockwave constantly?

    the shockwave and flash players crash constantly in Facebook apps ... every indication is that the plug in container grinds away with extraneous programming down loaded to it without my knowledge or permission. it also slows the over all performance of all systems or apps that i attempt to run for the same reasons. how do i get rid of those unwanted and unneeded programs and prevent their return ?

    You can change the permissions that are stored in the browser in the "about:permissions" page, however if its the plug in container [http://mzl.la/MLXx5x What is a plug in container? ] you can manage the plug in with these [https://support.mozilla.org/en-US/kb/use-plugins-play-audio-video-games instructions] and if you are running into specific issues you can troubleshoot [https://support.mozilla.org/en-US/kb/troubleshoot-issues-with-plugins-fix-problems the plugins with these]
    If you have any specific questions we are happy to help as well. Making them go away would prevent you from being able to watch/play the flash apps
    This also checks if they are up to date [http://www.mozilla.org/en-US/plugincheck/]
    [[Adobe Flash plugin has crashed - Prevent it from happening again]]

  • How do I get the tutorials to run once selected?

    Using Premiere Elements 10:  I select tutorials and the items to view and nothing happens, how do I get it to start?

    SEMAPM16
    Where are you selecting "tutorials". Are you clicking on the message bar at the bottom of the Premiere Elements 10 interface and trying to view "Adobe Elements Inspirational Browser" or are you elsewhere?
    Have you checked out Adobe TV Premere Elements
    http://tv.adobe.com/show/learn-premiere-elements-10/
    There is also the Premiere Elements 10 PDF Help to check out.
    http://help.adobe.com/en_US/premiereelements/using/premiereelements_10_help.pdf
    I have found this file to open very slowly.
    ATR

  • How do you get the CPU Usage in Linux

    This is a link of an example in WIN32:
    http://www.javaworld.com/javaworld/javaqa/2002-11/01-qa-1108-cpu.html
    It notes that UNIX environments should use getrusage(), and that is all it says in regards to UNIX. The code I have attempted to use looks like this:
    #include <sys/resource.h>
    #include <sys/time.h>
    #include "CPU.h"
    #include "jawt_md.h"
    #include "jawt.h"
    struct rusage usage;
    int ret;
    struct timeval val;
    struct timeval val2;
    JNIEXPORT jlong JNICALL Java_CPU_getProcessCPUTime (JNIEnv * env, jclass cls)
       ret = getrusage(RUSAGE_SELF,&usage);
       val = usage.ru_stime;
       val2 = usage.ru_utime;
       return val2.tv_usec;
    }My problm is that I don't think it is right...since the value returned is always the same no matter what the CPU usage is. same for if I used val instead of val2.
    Any Ideas?

    In Linux, you can read /proc/uptime. It does NOT give you the load averages that the command uptime gives. It gives you numerically the amount of time the CPU was idle vs how much time it was spent doing something. You need to read these two floating point numbers one every second, or once every 5 or 10 seconds then do the delta on the change: The maths are as follows:
    Read the file in twice in 5 seconds, parse into two floats/doubles:
    double[] last;  // the first read of the file
    double[] rect;  // the latest read of the file
    double ld = last[1] - last[0];
    double rd = rect[1] - rect[0];
    double cpu = (1.0d-(rd/ld)) * 100.0d;This should print the CPU percentage in Linux for that given time frame (5 second updates).

  • For the javascript content I am developing, the "hide status bar" option needs to be enabled; how do I access this option for FF4? If I cannot enable this option, can you provide tips on how I might get the page to run?

    I am working with datango producer (see datango.com) which depends on JavaScript to set up the training player that runs simulation content. Datango's browser check recognizes that I am running FF4.0, but indicates I should change the setting to hide the status bar, yet I cannot access that setting under Options > Content > Advanced JavaScript Settings. I could suggest an update to the preflight checks, but am not sure what to tell them. Can you help?

    https://support.mozilla.com/en-US/kb/what-happened-status-bar

  • How can I get the printer to run quietly. HP Officepro 8600 Plus. Windows 7 Starter edition,

    The printer is very noise.

    Refer to http://h30434.www3.hp.com/t5/Other-Printing-Questions/My-printer-is-noise-OfficePro-8600-plus/td-p/1...
    I am an HP employee.
    Say Thanks by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"

  • When I download a file I only have the option to SAVE no option to RUN How do I get the option to RUN?

    Firefox v7
    Win 7

    First, the required profile needs to be present. LR 5.4 supports the X-T1 in terms of understanding its Raw format, but will not come with a profile for every lens which can be mounted onto that.
    A profile is made for each specific lens, as mounted on a certain camera. It can also be used with pictures taken on a different (reasonably similar) camera body than the one originally used during profiling. This is subject to the sensor format: you can employ a given lens profile made for full frame, on an image from a crop sensor behind the same lens - but not vice versa.
    Next, the image type needs to correspond to the image type which has been built into the profile: Raw, or non-Raw.
    Lightroom offers only profiles of the right type for the image(s) concerned. There are many more provided for correcting camera Raw, than for correcting camera JPG. That is also the case with additional profiles, e.g. those accessed via the Adobe lens profile downloader utility.
    Finally, in the event that there simply is no profile out there for a given lens, it is not particularly difficult (though a little tedious) for the end user to generate one, using a further Adobe utility which is downloadable as a package, including a range of checkerboard calibration targets, each of which needs to be printed at a stated physical size.

  • Can't get the CPU utilization above 52%

    Hi all,
    I have an Intel i7 950 CPU based PC with Windows 10 TP on it which, no matter what, I cannot bring to 100% CPU utilization. While taking the attached screenshot, I was running prime95.exe.
    I have tested the same scenario on the same computer running Windows 8/8.1 and got the same result. However, when doing the same thing under Windows 7, CPU utilization went up to 100%.
    Anybody has any idea why this happens? Is it a different default setting somewhere (probably in registry)?
    Since I have this fast machine I would like to be able to use it at its full strength - the way things are now, my old Quad core 2 GHz PC is MUCH faster than this 8 core 3 GHz one (as I measured in several tests consisting of transcoding videos).
    Thanks for any pointers!

    Hi VikTak-9b,
    How did you get the CPU utilization information ?Are you getting the information from the task manager ?
    "I have tested the same scenario on the same computer running Windows 8/8.1 and got the same result. However, when doing the same thing under Windows 7, CPU utilization went up to 100%.
    Anybody has any idea why this happens? Is it a different default setting somewhere (probably in registry)?"
    I am a little confused here .According to my understanding ,the number is smaller the performance of the machine is higher when the other conditions are the same .
    Here is a link may be useful for us to understand the CPU Utilization for Performance Analysis
    Interpreting CPU Utilization for Performance Analysis
    http://blogs.technet.com/b/winserverperformance/archive/2009/08/06/interpreting-cpu-utilization-for-performance-analysis.aspx
    Best regards
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Case Fan Running at Full Speed

    I accidentally shorted the case fan circuitry on my HP motherboard (explanation below) and now the fan runs at full speed all the time. Other than the fact that is was a stupid thing to do, will it be a problem long-term and should I try to reset the fan speed switch?
    (Long Version) It is hot around here these days and my computer fans seemed underpowered. I put a splitter on the case fan outlet on the motherboard and added a second fan in addition to the original fan. It all worked fine except the new fan seemed to run pretty slow. I wanted to get a voltage reading from the fan plug but I accidently touched the two sensors on my volt meter and the computer immediately shut down. It started up and worked fine except the throttle was no longer working and the fans were running at full speed. This also explained why the second fan was running slowly before when they were both being throttled.
    I guess in the end I got my wish to have my fans running at full power, I just wanted to see if there will be any future problems leaving it this way.
    This question was solved.
    View Solution.

    Hello design_guy,
    You should not have any problems with the fans running at full speed other than the fact you may decrease the life cycle of the fan.
    You may want to install some software on the computer that will allow you to adjust the fan speed from the computer which may help you prolong the life of the fans and give you a little control over them.
    Something like SpeedFan should do the trick.
    If I have helped you in any way click the Kudos button to say Thanks.
    The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
    - Friendship is magical.

  • Macbook May 2010 edition exhaust fan runs at full speed

    Bought a new Macbook around February 2011. Yesterday all of a sudden while watching Netflix, the exhaust fan started running at full speed (Approximately 6200 RPM). I thought the machine was overheating. So I immediately shut it down and let it cool. But I noticed the machine was barely warm.
    When I started it up again, it started making the same noise with the exhaust fan running at full speed. I installed SMCFanControl and I see that the CPU is barely warm - 35-37C and yet the fan is running at full speed. I looked at the CPU/HDD usage and there is barely ANY usage (~90% idle). Nothing out of the ordinary. So it definitely doesn't seem to be a heating issue.
    In order to troubleshoot this I have done the following:
    1. Installed latest upgrade - Snow Leopard 10.6.7
    2. Reset SMC
    3. Reset the PRAM
    4. Tried booting from the install DVD. There as well it exhibits the same issue.
    Neither of these steps have helped me with my situation. I would really hate to go to the apple store as its always crowded and would end up wasting time. Are there any other steps I could try?
    Update: I tried running the Apple Hardware Test from the DVD. This is the error code that I got: 4SNS/1/40000001: TN1D- -1.000
    Can someone please tell me what this means?

    I don't know what that code means for sure, but it sounds like one of the temperature sensors may have died, so the fans just run at full to cool.
    I would take it to the apple store.

  • How can i get the max rpm from cpu fan??

    how can i get the max rpm from my cpu cooler regarding that i don't have a speed controller attached to the cpu fan ,,, ??  please make things clear for me
    thanks

    if you have not reduced it by using a speed controller either hardware or software or by the 7v mod its already going as fast as it will at 12 v dc you cannot speed it up only slow it down
    need more air get a different cooler/fan

Maybe you are looking for