How do I open ports in Norton Security by Comcast?
How do I open ports in Norton Security by Comcast?
You should ask them or find a forum relating to Norton Security. There's a chance someone here may know but this forum is for Apple TV so you may not get the help you need.
Similar Messages
-
I recently had a security system installed in my house. One of the features is an EPAD which enables me to have a virtual keypad on my iphone, and computer to operate the alarm system. The technician was not familiar with Mac's and Airports. How do I open port 80 to 80 in my airport and assign a fixed IP address for the EPAD? Apparently this is what is needed to make this work.
There are three ranges of "strictly local" IP addresses reserved for local Network use:
192.168.xxx.yyy
172.16.xxx.yyy
10.xxx.yyy.zzz
What your Router does for you is to act as your agent on the Internet.Your requests are packaged up and forwarded on your behalf, and only when a response is expected is the response returned to your local IP address.
Directing Network Traffic to a Specific Computer on Your
Network (Port Mapping)
AirPort Extreme uses Network Address Translation (NAT) to share a single IP address with the computers that join the AirPort Extreme network. To provide Internet access to several computers with one IP address, NAT assigns private IP addresses to each computer on the AirPort Extreme network, and then matches these addresses with port numbers. The wireless device creates a port-to-private IP address table entry when a computer on your AirPort (private) network sends a request for information to the Internet.
If you’re using a web, AppleShare, or FTP server on your AirPort Extreme network, other computers initiate communication with your server. Because the Apple wireless device has no table entries for these requests, it has no way of directing the information to the appropriate computer on your AirPort network.
To ensure that requests are properly routed to your web, AppleShare, or FTP server, you need to establish a permanent IP address for your server and provide inbound port mapping information to your Apple wireless device.
To set up inbound port mapping:
1) Open AirPort Utility, select your wireless device, and then choose Base Station > Manual Setup, or double-click the device icon to open its configuration in a separate window. Enter the password if necessary.
2) Click the Advanced button, and then click Port Mapping.
3) Click the Add button and choose a service, such as Personal File Sharing, from the Service pop-up menu. -
How can I open ports on my AirPort Extreme, from WINDOWS?
I have an Airport Extreme as my router, and I have a Windows-based computer. I need to open ports on the router (ironically, it is for my Apple TV).
However, even though I can use the Airport Utility for Windows (latest version 5.5.3), I cannot open ports from the application.
Everywhere I look, I am supposed to have a firewall tab in the Advanced section, but I do not have it. The only tabs that I have in Advanced are:
Logging and Statistics
MobileMe
IPv6
How can I open ports on my Airport Extreme router from Windows?Is your AirPort Extreme the only router in your network configuration?
-
I have flash media server but how can i open port 1935
how would i open
Port 1935 on my server as i think this is why my streaming in flash med
ia server does not workThis is my port details from command prompt Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:\Users\Administrator>netstat Active Connections Proto Local Address Foreign Address State TCP 127.0.0.1:11110 WIN-L969VFMO5GO:49242 ESTABLISHED TCP 127.0.0.1:19350 WIN-L969VFMO5GO:49167 ESTABLISHED TCP 127.0.0.1:19350 WIN-L969VFMO5GO:49243 ESTABLISHED TCP 127.0.0.1:49167 WIN-L969VFMO5GO:19350 ESTABLISHED TCP 127.0.0.1:49242 WIN-L969VFMO5GO:11110 ESTABLISHED TCP 127.0.0.1:49243 WIN-L969VFMO5GO:19350 ESTABLISHED TCP 192.168.1.65:1111 WIN-L969VFMO5GO:50394 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50371 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50393 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50395 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50398 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:51012 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:51091 ESTABLISHED TCP 192.168.1.65:49230 a92-123-153-19:http CLOSE_WAIT TCP 192.168.1.65:49231 a92-123-153-83:http CLOSE_WAIT TCP 192.168.1.65:50371 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50393 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50394 WIN-L969VFMO5GO:1111 ESTABLISHED TCP 192.168.1.65:50395 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50396 192.150.8.200:https CLOSE_WAIT TCP 192.168.1.65:50398 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:51012 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:51091 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:51412 text:http TIME_WAIT TCP 192.168.1.65:51413 text:http TIME_WAIT TCP 192.168.1.65:51416 bits:http TIME_WAIT TCP 192.168.1.65:51417 bits:http TIME_WAIT TCP 192.168.1.65:51418 bits:http TIME_WAIT TCP 192.168.1.65:51419 bits:http TIME_WAIT TCP 192.168.1.65:51421 bits:http TIME_WAIT TCP 192.168.1.65:51425 bits:http TIME_WAIT TCP 192.168.1.65:51432 text:http CLOSE_WAIT TCP 192.168.1.65:51433 bits:http TIME_WAIT TCP 192.168.1.65:51438 bits:http TIME_WAIT TCP 192.168.1.65:51439 bits:http TIME_WAIT TCP 192.168.1.65:51444 w2:http ESTABLISHED TCP 192.168.1.65:51445 ww-in-f149:http ESTABLISHED TCP 192.168.1.65:51447 mpr5:http TIME_WAIT TCP 192.168.1.65:51450 wy-in-f144:http ESTABLISHED TCP 192.168.1.65:51451 ir1:http ESTABLISHED TCP 192.168.1.65:51452 mpr6:http TIME_WAIT TCP 192.168.1.65:51453 ir1:http ESTABLISHED TCP [fe80::7800:6e:735:c444%13]:3389 pc-PC:49161 ESTABLISHED C:\Users\Administrator>ping 192.168.1.65 Pinging 192.168.1.65 with 32 bytes of data: Reply from 192.168.1.65: bytes=32 time<1ms TTL=128 Reply from 192.168.1.65: bytes=32 time<1ms TTL=128 Reply from 192.168.1.65: bytes=32 time<1ms TTL=128 Reply from 192.168.1.65: bytes=32 time<1ms TTL=128 Ping statistics for 192.168.1.65: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\Users\Administrator>netstat -a Active Connections Proto Local Address Foreign Address State TCP 0.0.0.0:80 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:135 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:445 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:1111 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:1935 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:3389 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:6515 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:8134 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:47001 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49152 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49153 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49154 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49155 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49163 WIN-L969VFMO5GO:0 LISTENING TCP 0.0.0.0:49164 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:9421 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:9422 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:9423 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:11110 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:11110 WIN-L969VFMO5GO:49242 ESTABLISHED TCP 127.0.0.1:19350 WIN-L969VFMO5GO:0 LISTENING TCP 127.0.0.1:19350 WIN-L969VFMO5GO:49167 ESTABLISHED TCP 127.0.0.1:19350 WIN-L969VFMO5GO:49243 ESTABLISHED TCP 127.0.0.1:49167 WIN-L969VFMO5GO:19350 ESTABLISHED TCP 127.0.0.1:49242 WIN-L969VFMO5GO:11110 ESTABLISHED TCP 127.0.0.1:49243 WIN-L969VFMO5GO:19350 ESTABLISHED TCP 169.254.196.68:139 WIN-L969VFMO5GO:0 LISTENING TCP 192.168.1.65:139 WIN-L969VFMO5GO:0 LISTENING TCP 192.168.1.65:1111 WIN-L969VFMO5GO:50394 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50371 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50393 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:50398 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:51012 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:52277 ESTABLISHED TCP 192.168.1.65:1935 WIN-L969VFMO5GO:52388 ESTABLISHED TCP 192.168.1.65:49165 WIN-L969VFMO5GO:0 LISTENING TCP 192.168.1.65:50371 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50393 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:50394 WIN-L969VFMO5GO:1111 ESTABLISHED TCP 192.168.1.65:50396 192.150.8.200:https CLOSE_WAIT TCP 192.168.1.65:50398 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:51012 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:52277 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:52319 a92-123-153-19:http CLOSE_WAIT TCP 192.168.1.65:52388 WIN-L969VFMO5GO:1935 ESTABLISHED TCP 192.168.1.65:52592 wy-in-f157:http ESTABLISHED TCP 192.168.1.65:52593 wy-in-f157:http ESTABLISHED TCP 192.168.1.65:52612 ww-in-f155:http ESTABLISHED TCP 192.168.1.65:52619 ww-in-f102:http ESTABLISHED TCP 192.168.1.65:52620 a92-123-153-25:http ESTABLISHED TCP 192.168.1.65:52626 a92-123-153-81:http ESTABLISHED TCP 192.168.1.65:52717 fe:http TIME_WAIT TCP 192.168.1.65:52720 91.103.142.194:http ESTABLISHED TCP 192.168.1.65:52722 a92-123-153-10:http ESTABLISHED TCP 192.168.1.65:52724 a92-123-153-10:http ESTABLISHED TCP 192.168.1.65:52725 a92-123-153-10:http ESTABLISHED TCP 192.168.1.65:52726 a92-123-153-10:http ESTABLISHED TCP 192.168.1.65:52729 65.242.27.32:http TIME_WAIT TCP 192.168.1.65:52730 65.242.27.32:http TIME_WAIT TCP 192.168.1.65:52732 ww-in-f102:http ESTABLISHED TCP 192.168.1.65:52734 64.236.76.160:http ESTABLISHED TCP 192.168.1.65:52739 ec2-79-125-122-81:http ESTABLISHED TCP 192.168.1.65:52740 95.101.16.74:http ESTABLISHED TCP 192.168.1.65:52741 mpr2:http TIME_WAIT TCP 192.168.1.65:52742 ec2-79-125-28-85:http TIME_WAIT TCP 192.168.1.65:52744 a92-123-153-9:http ESTABLISHED TCP 192.168.1.65:52745 mpr2:http TIME_WAIT TCP 192.168.1.65:52746 wy-in-f156:http ESTABLISHED TCP 192.168.1.65:52747 a92-123-153-82:http ESTABLISHED TCP 192.168.1.65:52749 64:http TIME_WAIT TCP 192.168.1.65:52757 64:http TIME_WAIT TCP 192.168.1.65:52760 mpr2:http TIME_WAIT TCP 192.168.1.65:52761 ec2-79-125-28-85:http TIME_WAIT TCP 192.168.1.65:52763 mpr2:http TIME_WAIT TCP 192.168.1.65:52764 64:http TIME_WAIT TCP 192.168.1.65:52770 194.129.79.23:http TIME_WAIT TCP 192.168.1.65:52774 mpr2:http TIME_WAIT TCP 192.168.1.65:52776 mpr2:http TIME_WAIT TCP 192.168.1.65:52782 mpr2:http TIME_WAIT TCP 192.168.1.65:52783 ec2-79-125-28-85:http TIME_WAIT TCP 192.168.1.65:52785 mpr2:http TIME_WAIT TCP [::]:135 WIN-L969VFMO5GO:0 LISTENING TCP [::]:445 WIN-L969VFMO5GO:0 LISTENING TCP [::]:3389 WIN-L969VFMO5GO:0 LISTENING TCP [::]:47001 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49152 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49153 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49154 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49155 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49163 WIN-L969VFMO5GO:0 LISTENING TCP [::]:49164 WIN-L969VFMO5GO:0 LISTENING TCP [fe80::7800:6e:735:c444%13]:3389 pc-PC:49161 ESTABLISHED UDP 0.0.0.0:53 *:* UDP 0.0.0.0:500 *:* UDP 0.0.0.0:3702 *:* UDP 0.0.0.0:3702 *:* UDP 0.0.0.0:4500 *:* UDP 0.0.0.0:5355 *:* UDP 0.0.0.0:6514 *:* UDP 0.0.0.0:50854 *:* UDP 0.0.0.0:50856 *:* UDP 0.0.0.0:50858 *:* UDP 0.0.0.0:56952 *:* UDP 127.0.0.1:49293 *:* UDP 127.0.0.1:50781 *:* UDP 127.0.0.1:50855 *:* UDP 127.0.0.1:53143 *:* UDP 127.0.0.1:58363 *:* UDP 127.0.0.1:58653 *:* UDP 127.0.0.1:59769 *:* UDP 127.0.0.1:63390 *:* UDP 127.0.0.1:64492 *:* UDP 169.254.196.68:137 *:* UDP 169.254.196.68:138 *:* UDP 192.168.1.65:137 *:* UDP 192.168.1.65:138 *:* UDP [::]:500 *:* UDP [::]:547 *:* UDP [::]:3702 *:* UDP [::]:3702 *:* UDP [::]:4500 *:* UDP [::]:5355 *:* UDP [::]:50857 *:* UDP [::]:50859 *:* UDP [::]:56953 *:* UDP [fe80::b0e8:29cf:aafb:800c%11]:53 *:* C:\Users\Administrator>
-
I am using a 2wire modem/router. I was told by a tech at ATT that I can only click a button that allows ALL ports open, but not just port 80.
Does anyone know if there is a way to open port 80 ONLY? I'm next to done setting up a security CCTV system for my home, and this would allow me to use my computer to look at whats going on, rather than buying a new monitor.
Thanks for helping.Thanks for the reply. You and X423424X are close. From the beginning. I bought a 4 camera DVR security surveillance system. Yesterday, we installed it. I was told by the place from which I bought it ( and subsequently from the manufacturer's tech guy) that if I wanted to use my computer for a monitor for the security setup, that in the Router Firewall Settings I would have to identify the device, and then 'direct' the device "through" port 80 to be able to view the 'goings on outside' (the input from the cameras) from my computer monitor. Inclusive with this configuration via the iMac, is that the DVR is recording all the time, and I could download any portion of the recorded material from the DVR to the iMac and burn it to a disk, for example to give to the cops if there was a theft. AND, it was also mentioned that in order to remote view whats going on around the place from say, a laptop or pc when I'm out of town can also be done, but that would require opening another port, with 4 digits, like 3806, or similar. I will eventually get the port number for this operation later. So that is what I'm trying to do.
So far, the 'local tech' from the security store seems to have limited knowledge of the Mac, and of the 2Wire router/modem. So HE was on the phone with first the tech support from the security cam/DVR dealers, and then with an ATT tech. The ATT tech was the one that said, in the firewall settings on the modem, there is a button that opens ALL ports, and that was the only way to allow port 80 to be used for the DVR/security setup.
I think that he is incorrect. I think that there is a way to view the camera images on my Mac monitor, and that there is a way to configure the settings on the router to allow the camera images to be seen on the computer screen, and that I could also download to the HD on the iMac any 3 or 4 minute portion of what is recorded on the DVR, in order to burn a copy. I have a co-worker that had a car taken, and her neighbor was there in an instant telling her thatt he had the whole thing on his video surveillance, and had a disc burnt in about 5 minutes, which went to the police. Her car was found, and the perp arrested within 2 hours.
THATS what I want to end up with (no, not a stolen car, but the configuration), and I'm hoping that I can find the way to get 'er done here. There is only one good Apple/OS X tech in this town, and he is on vacation for another week. AND, I'm not sure he is a 2wire expert.
So, again, thank you for any help or input. -
Torrents, how do I open ports
I have a Netgear DG934G Router from Sky which is broadcasting a 'B/G' only network. To this, connected by ethernet I have an Airport Extreme which runs a seperate 'N' only network. The Extreme is set to bridge and the Netgear distributes the IP addresses.
How would I use Transmission? How do I forward the ports on the extreme to allow it to download?
I use the B/G network for my partners laptop and the iPhone and I use the N network for my macbook, apple tv and my Airport express to stream music....I am wondering why then does my apple tv not pick up on the N network, only the G network?
The ability to pick up the wireless signal from the AEBS has absolutely nothing to do with opening ports. This relies only on the strength and quality of the RF signal reaching the Apple TV.
Also I wanted to use an Extreme to extend the N network but when I am trying to set it up, it will not see the N network in the Airport Utility.
I am confused. If the AEBS is creating the N network how is it going to extend the N network? -
I recently purchased several internet cameras. Not webcams. You can set them up to be viewed by any computer via the internet. Now it is my understanding that I need to open two ports. One for the web server and the other for the actual image transfer. I can assign separate IP's, and Web server and image transer ports throught the camera software for each individual camera. My internet connection setup in DHCP. Does this need to be Static? Can anyone explain to me how to exactly open the appropiate ports on my router to be viewed over the internet?
Windows XP
WRT54G v4
Also do I need to make any exceptions regarding the windows or the router firewall?
Thanks for any insight.Hi… You would need to change the IP address on all the cameras to be static and unique and also need to change the port on the cameras from 2064 to 2065 to second camera, 2066 to third and so on. Now you can go ahead and forward the these ports on the router for corresponding IP address.
-
How to forward/open ports for WRT54G?
Hi. I recently bought a WRT54G because my old router was destroyed by lightening and thunder. I have managed to set it up, and got the interent itself to work with static IP adress (192.168.1.101 for my PC).
However, even though I have tried to forward/open ports for applications like uTorrent and DC++ as well as Limewire, I have no luck. When I test if the ports are indeed opened, I get the result that they are not. Here are how my port forward setting looks like for utorrent. The port in the settings image is of course the same as in uTorrent.
http://www.pictub.com/quickupload/01/untitled-1mb4wd.jpg
I can't seem to open any ports, even though I have followed tutorials like the ones at portforward.com. I have the latest firmware for my router, as I flashed it when I got it. Help .Yes, I did .
Anyways, look what I found in the uTorrent FAQ:
1.7 Special note for users with Linksys WRT54G/GL/GS routers, there are severe problems with them when running any P2P application
To fix it, they say one has to flash with a unofficial firmware, but I will rather get the money back and buy another router tomorrow. Thanks for the help anyways . -
How do you open port 3283 when firewall is off?
I've had no success trying to get ARD working on a new Snow Leopard Server 10.6.2 install on an XServe. Can't get it working from the Sharing control panel, and tried all the different syntax options in kickstart here
http://discussions.apple.com/thread.jspa?threadID=2342445&tstart=15
and here http://support.apple.com/kb/HT2370
A port scan shows that port 3283 is closed, but the computer firewall is off, and there is no external firewall. Another 10.6.2 Server works fine on ARD, so it's internal to the first one.
How can I open that port? Hoping that's the problem.
Thanking anyone for feedback.It's probably a Mac OS X firewall fault, where it's actually holding that port closed even though it claims the firewall is off. I'd suggest you ask in the Mac OS X Server forum; you'll be more likely to get help with this problem there this not being an ARD problem per se.
This of course presumes that the Xserve isn't behind a router that might be filtering that port. If both Xserver are on the same subnet, that probably won't be the case, but if the problem Xserve is on a different subnet, you might check the router's filter.
Regards. -
How to block opening a file for security purposes
There is a chance my MacBook may need repairs for case issues. I have some personal information on my computer that I want to protect from prying eyes.
How would I do this?
Thank you!Hi the musigal
You could create a disk image and encrypt it with a password. Move the files into that and delete the originals. On return, copy them back from the disk image to their original locations.
To create a disk image:
Open Disk Utility.
Select New Image
Give it a name, select a size and choose Enrcryption
Click Create
Enter a chosen password twice (make it different to your normal one)
The newly created disk image will appear mounted on the Desktop, if that is the location you chose for it.
Move your sensitive files into it.
Unmount it (eject it)
Test it by double clicking on it, supply your password.
Once opened (mounted), check your files are in there and work correctly.
Again eject it. It can remain on your computer as it can't be opened except by you.
Delete the original files.
regards roam -
How do I open port 1701 on my Mac?
I've got my Airport Extreme set properly, and "ipfw" is turned off/set to open. However, when I run the Port Scan with Network Utility from my Macbook on my local area network, neither port 500, 1701, or 4500 show up as open. Because I'm not seeing it from one mac to another on the local network, that leads me to conclude there is something on my Mac Pro, running OS X Server 2.2.1 and OS X Mountain Lion 10.8.4, that is keeping those ports closed. What could it be if not the ipfw firewall?
My hours of internet research have not otherwise turned up a way to affirmatively open a port in Mac OS X—only the ability to close a port using ipfw. Please help!Reviewing relevant comments, my guess is this is one of those mysterious issues that requires a reinstallation of Mountain Lion. It appears that there is some ghost in the Server program and my Mac Pro that results in the VPN thinking it is working and ready to go when, in fact, it is not. This would not be the first ghost in OS X Server and/or my Mac Pro, as you can see if you review the questions I've asked on this board.
I don't know if I have it in me to risk something else going wrong with OS X Server after the reinstallation. Ironically, however, the only thing I can get it to do is run a Time Machine server for my one laptop . . . but I had such a hard time getting Open Directory up and working that I am reallly hesitant to start over–even though I don't use Open Directory for anything. Maybe someone could suggest a good third-party VPN service? -
How do i open ports on a mac with a wrt54g
i need to open 6 of them for that new xbox and i have no clue what they are talking about,i am not good on pc,s i have a imac and wrt54g v3 please help
Solved!
Go to Solution.In a web browser type 192.168.1.1 in the address bar, just lke where you'd type www.bing.com or www.yahoo.com.
-
your link wwww.mozilla.com/en-us/firefox/all-older does not apear to work
You can get Firefox 3.6.16 here:
http://www.mozilla.com/en-US/firefox/all-older.html
http://support.mozilla.com/en-US/kb/Installing+a+previous+version+of+Firefox -
As the title suggests...
I have a mix of five Mac and PC's at home using an Airport Extreme Base Station as the router. I need many ports opened on the AEBS for all of the computers- not just one computer. (for example: three people want to play TF2 on Steam at the same time; each machine needs the correct ports open on the router). Port forwarding only allows me to forward a given port to a single IP, yet I need that port open for five differnt IP's, all at the same time.
How do I do that on an AEBS?
In the same way, I have a small office of four iMacs using an old airport with the same exact issue. I would like to be able to connect to all of them remotely with Apple Remote Desktop, but the port forwarding on the airport only allows a port to forward to a single IP. I want to be able to tunnel into the office network and log onto any machine behind the Airport extreme... not just a single IP. I currently have it set up where I can tunnel into the office from my house, I can find the one machine that the port forwarding has been assigned to, I can log on and everything is just fine... with one machine. How do I open the firewall for the other machines?
TL,DR version: How do you open ports on an Airport Extreme Base Station instead of forwarding ports? Forwarding ports doesn't work for multiple IP's.You can open a single or multiple ports to a single device or different ports to different devices, but you cannot open the same port to multiple devices via the AirPort Utility for the Apple routers.
-
How do you open ports 80 and 443? I'm trying to connect a tv to the internet.
What router are you using? Who is your ISP? Also, what exactly are you trying to accomplish?
Maybe you are looking for
-
Passing value from JSP to Action in Struts
Hi, I am populating JSP page with rows retrieved from the database and represented as a List of Beans in forEach loop: <c:forEach var="list" items="${OperationsForm.OperationsList}"> <c:choose> <c:when test="${list.isCompleted =='Y'}" > <td width="10
-
Logo in the Footer of the RTF doesn't show in PPT output
Hello I try generate a Powerpoint slide deck with a logo at the bottom of each slide. Therefore I have inserted the picture into the footer of the RTF template. When generating the ppt output there is not picture at the bottom of the slides. I played
-
Webdynpro ABAP: data binding for node having subnodes and attributes
Hello, Problem description: There is parent node (cardinality 0..n), which has some attributes and also a sub node. This parent node has to be bound to an internal table. The fields of internal table correspond to the attributes of the parent node. N
-
Hi, Is there anyway Oracle EDQ can provide restful services instead of SOAP services? Thanks,
-
Java method to call LabView on remote computer
Greetings, I am very new to LabView and have a Java programming background. I have to put together a way to submit a String to a LabView vi on a remote computer. The Labview should then return another String to my Java program. I just need an examp