How do I speed up my USB 3.0 port

I have Windows 7 Home Premium 64 bit.  I am getting messages to the effect that my mass storage device will perform faster if I configure my USB 3.0 port.  How can I speed up my USB 3.0 port

The picture is not visible yet, but do you have this driver installed?
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-103655-1&cc=us&dlc=en&lc=en...
Install this driver and reboot. If that does not work try uninstalling drivers for each usb device and reboot to let the driver reinstall.

Similar Messages

  • How do I disable only the USB 2.0 ports - K7T266 Pro2-RU

    None of the USB ports on this MB will work with my Biostar 6-in-1 card reader - however, I have a VIA USB 2.0 PCI card that works fine with it. I want to disable the 2.0 ports only, and install the PCI card. The manual is not very helpful - if I only enable USB 2, which seems to be the USB 1.1 header, that DOES disable the USB 2.0 ports, but it also disables the 2 USB 1.1 ports on the MB!

    Yes, and they are labled USB1, USB2 and USB3 - now I assume that these correspond to the JUSB1, JUSB2 and JUSB3 headers on the MB, with JUSB2 being the 1.1 ports on the D-LED bracket, and JUSB1 and JUSB3 being the 2.0 headers. I can only ENABLE certain USB ports in the BIOS - i.e. if I only enable JUSB2, this effectively disables the 2.0 ports - aha - it also disables the 2 1.1 ports on the back of the MB itself!!
    Any other answers?

  • How do i activate Sony HS-USB Android Diag ports on Xperia Z3?

    Hi Folks. I have been trying to get the HS-USB Android Diag/Modem/Serial ports activated so that they show in Device Manager, to no avail.  Is there a special number sequence i enter into the dialler? Or is there a special USB driver i have to install? I am able to to activate these ports using my Samsung S4, so surely it is possible for the Xperia Z3?! I remember successfully doing this on an earlier Xperia phone, but cannot how i did it. Would be grateful for any help please. Thanks in advance.

    Yes i have installed PCC, but still not able to activate the Diag ports. Really frustrating this is, as with Samsung all i did was install their Kees software and instantly the Diag/Modem ports were activated. I will have to keep trying/searching and hope somehow i can do/find it. Thanks for your suggestion though!

  • How to replace the installed Generic USB Hub to Generic Super Speed 3.0 USB Hub?

    Hi I have a problem with my RMBP 15" USB PORTS (both are 3.0 physically). Most of the days I will use windows 7 home premium through bootcamp.
    When I connect my WD My Passport 3.0 to the usb port, there will always a pop up saying "Your device can work faster if it connects to a Super Speed 3.0 USB Port and when I do file tranferring between these 2 devices I will only get an average speed of 30 mb/sec which is DEFINITELY a speed of usb 2.0. As the usb 3.0 will be able to transfer (in reality) up to 100 mb/sec.
    I think there is something wrong with the drivers installed. Attached is my device manager showing all the USB drivers installed.
    Please advise me on what should I uninstall and install and where can I download the drivers or firmware.
    For additional information, my macbook in using Intel Chipset C216.

    This is more for googlers/random people in the same boat, since the OP may not be checking this any more.
    I have arrived at this thread from another angle: I downloaded 'SlimDrivers', a free and non-contaminated 'driver updater' Windows program which is heavily-reviewed, on CNET as actually GOOD as opposed to almost all other 'dodgy' driver update checker programs out there (like Driver Reviver, Device Doctor, and Driver Detective - not to mention the scammy and notorious DriverAgent, of course).
    I hit scan, and a whole set of drivers - seemingly under the one chipset download (as assisted by this youtube run-through) - came up. It's extremely user friendly and downloads the installer for you right from within the app. I've yet to install the chipset driver and restart - fingers crossed - but I think it's the same driver as OP is talking about.
    Cos I've also noticed, at least once, some sort of USB issue in the past which made me think "huh, USB 3.0 mustn't be working with the bootcamp driver eh?"
    So *I'm* wondering, whether what I've stumbled upon is indeed the same matter as OP, and thus also, maybe is a solution to the OP question as well .

  • How to get an N wireless USB adapter to transfer data faster that 54 Mbps

    How to get an N wireless USB adapter to transfer data faster that 54 Mbps? I am running FIOS 10/2 and connected to a ActionTec  M1424WR router. Any help will be appreciated.

    I have to ask the question, why are you in need of 802.11N speeds?  Are you transferring lots of files between other PC's on your network or are you simply connecting to the Internet.  
    Remember if your Internet speed is 10/2 which means 10 meg down and 2 meg up having 300 meg capability WLAN connection will not be noticeable.   Your bottleneck is your Internet connection of 10/2.   

  • How do I know whether the USB port in my macbook air is 2.0 or 3.0?

    How do I know whether the USB port in my macbook air is 2.0 or 3.0? I really want to use a usb flash drive that has faster read/write speed but I don't kow if it would be supported by my macbook air - I purchased the macbook air from the apple store on autumn 2011, 1.7Ghz Intel Core i5

    Eddy ~ The free Mactracker app shows USB info and much more:

  • Usb 3.0 port works with slow speed

    i have hp 15r-007tx laptop
    when i try to use usb 3.0 port it works with usb 2.0 speed i have inserted in correct usb port and  installed all the drivers but still speed is very slow 

    vibhors wrote:
    using transcend hdd 500 gb just movies getting 20-25 mbps speed same as usb 2.0
    Hi,
    What is the model of your transcend ? Is it USB 3.0 drive ? How big each movie ? Many smaller movie files will slow  them down.
    Regards,
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • TS2570 System runs slow after upgrading 2010 macbook to Mavericks. How do i speed it up again? Defrag? if so how.

    Downloaded Mavericks to my fast running 2010 Macbook a couple of days ago and since this the whole system is running slow.
    How can i speed it up again please?

    Fixing a Mavericks Installation Problem
    How to manage a failed OS X Mavericks installation | MacFixIt - CNET Reviews.
    Try these in order:
    1. a. Resetting your Mac's PRAM and NVRAM
        b. Intel-based Macs: Resetting the System Management Controller (SMC)
    2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
         Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
         COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and
         after the chime press and hold down the OPTION key until the boot manager screen appears.
         Select the Recovery HD and click on the downward pointing arrow button.
    3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
    4. Reinstall Lion/Mountain Lion, Mavericks: Reboot from the Recovery HD. Select Reinstall Lion/Mountain Lion, Mavericks from the Utilities menu, and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • How do I install windows from USB on Macbook pro 3,1

    How do I install windows from USB on Macbook pro 3,1 ?
    My Superdrive is far from super anymore, So I managed to make an extern drive with both Snow Leopard Partition, Lion Partition (Since I thought Boot Camp 4,1 would bypass my problem), and Time Machine partition, Since I got 1. USB drive that works.
    - My general issue is that Boot camp Refuse to see the USB drive - (Many "how to"´s though show how they install windows perfectly through the USB port, but they use airbooks!, and somehow the Macbook will not ?)
    I fix that issue with >> rEFIt <<, that suddenly makes it possible for the Mac to see the USB drive, and partitions.
    Which was very strange since I could use an extern HD with the whole installation to start up wipe the whole disk, and then use my extern drive with partitions to install Snow Leopard and get everything as before with timemachine. Very smart with timemachine, but very lucky that I have a extern drive that runs the whole system and that I made the partitionsdrive before. DVD-drives are the past!
    Point: So the original system could see the Snow Leopard installation USB disk, but boot camp cannot find the USB drive ?????????
    After rEFIt I booted and then I got this error:
    Starting bootmgr.efi
    Error: Unsupported while loading bootmgr.efi
    I read it could be a problem with the Windows software, so I purchased an extern DVD drive, Used Disk Utility to make an image (.DMG), then used another program to convert the .dmg to .ISO.
    Then downloaded a trialversion of vmWare fusion, and installed windows from the iso. Everything worked brilliant, except and that is why I want to use boot camp, Running windows in another program while running the mac system is a little hacky and slow.
    Point: Nothing is wrong with the windows software, and windows runs fine.
    I then downloaded the Windows DVD / USB Tool, reformatted a USB drive as Master Boot Partition, MS-Dos Fat partition, then after lots of struggling got Vmware, windows to recognise the USB drive. And installed the windows software on the USB drive, as all the walkthroughs recommend.
    Then I tried for "fun"! to just install windows form the extern USB drive, and with rEFIt it will see the drive and start to do something, but then when it starts to boot, the screen just turns into black and nothing happens, and you can see the drive does NOTHING. (I think it is because I only have 1 USB drive and the Extern DVD drive does not get enough power, but again the mac refuse to see the USB drive unless it is a Snow Leopard installation USB-drive!
    Well trying to install Windows Ultimate 64 Bit, which worked great in vmware, because that program installed from the .ISO file that I had on the desktop, but trying with Boot Camp did not get anywhere, what kind of **** program is this boot camp anyway!?, but then I try the new USB disk with windows made from windows, thorugh rEFIt, it sees the disk and then starts and then I get this ERROR:
    rEFIt - Booting Legacy OS
    Starting legacy loader
    Using load option ´USB´
    Error: Not found returned from legacy loader
    Error: Not found from LocateDevicePath
    (x 9 times)
    Error: Load Error while (re)opening our installation volume
    The firmware refused to boot from the selected volume. Note that external hard drives are not well-supported by Apple´s firmware for legacy OS booting
    (Hey Apple please send out a updated firmware that fix this issue?!)
    So how do I do it ? - or is the only option to fix the partition running the system from the extern disk. Format the whole drive in 2 from the "bottom" and install windows and then afterwards install Mac on the other partition ?  Or just run windows on the mac and forget about mac software ? What a stupid solution...

    There are strings in the pliist file to add other Macs so that you can use some USB-DVD drives.
    This is 5 page thread, so a little more 'meat' to it:
    https://discussions.apple.com/thread/3410900?start=60&tstart=0
    And on PC booting Windows from a USB DVD to do the install is usually a piece of cake, sometimes you just need to specify that USB in the BIOS boot order and sometimes select via F12 (or another Fkey) and that is it.
    What you have here seems to be everything and everyone is excluded unless there is a  mac-model device ID string that specifies yes.  An unnecessary hurdle.

  • TS2756 How can i create a new usb connection (service)  on my iMac for sharing internet from my iPhone5 ( i seem have to deleted it )

    How can i create a new usb connection (service)  on my iMac for sharing internet from my iPhone5 ( i seem have to deleted it )
    i know its not a problem whit my carrier o data plan or sharing preferences on the ipone because when i use it un my laptop it works perfectly through
    the usb and even works on the Imac through wifi and bluethood tethering but NOT through usb!!.
    the problem is that trying to make it work i deleted the "profile" usb iphone on the network prefereces panel. Now i only have 3 options: ethernet / wifi / bluetooth
    but not the usb iPhone i used to have.
    And when i try to add a new one i dont get a USB option.
    can some one help me please??
    this is how it looks (after the bluetooth PAN i used to have USB iPhone option)

    The question would be more appropriate in the Mac forums as it is not really related to the iPhone.

  • How do I create multiple live USBs of Operating systems to boot from on one flashdrive?

    How do I create multiple live USBs of Operating systems to boot from on one flashdrive?
    I am attempting to create multiple live USBs within one flashdrive so that i can boot various operating systems without having to buy multiple USb sticks. I am using a Mac OS X Snow Leopard 10.6.8 Operating System currently. I am using the Terminal provided by the OS.
    I would like to try Debian, Kali, Precise Puppy, and Sabayon- with one space left empty for whatever Linux OS I would like to try next. I have partitioned an 8GB flashdrive into the following sections:
    name of intended OS,     space allocated for it:
    1)Debian ........................1.32 GB
    2)Kali..............................2.61GB
    3)Precise Puppy..............163.7MB
    4)Sabayon.......................1.77GB
    5)TBD..............................2.14GB
    I have figured out how to change the .iso files of the operating systems into .img files with the following commands:
    hdiutil convert -format UDRW /path/to/input.iso -o /path/to/output.img
    a .img.dmg file is created, this is corrected in the next line of code *please note: I am a a very beginner at programming, and would greatly appreciate any help. Thank you!
    mv /path/to/output/file.img{.dmg,}
    This is where I started to get confused:
    I entered diskutil list to find the location of the partitions on my flashdrive, and this is the relevant section:
    /dev/disk1
       #:                       TYPE NAME                    SIZE       IDENTIFIER
       0:     FDisk_partition_scheme                        *8.0 GB     disk1
       1:                 DOS_FAT_32 DEBIAN               1.3 GB     disk1s1
       2:                 DOS_FAT_32 KALI                    2.6 GB     disk1s2
       3:                 DOS_FAT_32 PRECISE            163.7 MB   disk1s3
       4:                 DOS_FAT_32 SABAYON           1.8 GB     disk1s5
       5:                 DOS_FAT_32 TBD                     2.1 GB     disk1s6
    This is the code I attempted to use and the subsequent result:
    charles-burtons-mac-mini:~ charlesburton$ sudo dd if=/Users/charlesburton/Desktop/debian-live-7.2-i386-gnome-desktop.img of=/dev/disk1s1 bs=1m
    dd: /dev/disk1s1: Resource busy
    *at this point I went to the Disk Utility GUi and unmounted only the DEBIAN partition, now back to the terminal*
    charles-burtons-mac-mini:~ charlesburton$ sudo dd if=/Users/charlesburton/Desktop/debian-live-7.2-i386-gnome-desktop.img of=/dev/disk1s1 bs=1m
    dd: /dev/disk1s1: end of device
    1259+0 records in
    1258+1 records out
    1320005632 bytes transferred in 1011.966891 secs (1304396 bytes/sec)
    Please may someone help explain why I had a return value of +1 in my records in and how I can make it work properly.

    I would like to know the answer to this as well.  I tried renaming the 3D version by adding 3D after it, but it still not a separate movie in iTunes.
    It's putting them in the same folder.

  • How can I speed up the extract() function queries on XML

    Hi,
    Please I need some light on xml and indexes.
    This is my case:
    I use Oracle 9i R2.
    I have a table with some rows containing some few xml documents (each row contains a big xml document).
    Given a value for an attribute of a tag, I want to extract the entire section within the tags.
    Example:
    <MYTAG number="1">
    .....big stuff here
    </MYTAG>
    <MYTAG number="2">
    .....big stuff here
    </MYTAG>
    <MYTAG number="x">
    .....big stuff here
    </MYTAG>
    So for number=2 I would like to extract from the document the xmltype
    <MYTAG number="2">
    .....big stuff here
    </MYTAG>
    I created an index and have followed all the steps from the XML Database Developers Kit manual. Then I would use extrac() as the document says.
    Now some doubts arised:
    Are these text/xml indexes only useful for getting the rowid of my document?
    I mean, if I select 'x' from the table looking for some value, then the index is used. But when I use extract in the select to get the section I look for, the query gets really low, specially when xml documents are big. I think when I have only row with one document, getting the rowid is not the problem, but the extraction from the document is.
    Is the extraction process faster because of the index?
    For what I see, the index only helps me to find the rowid, but then Oracle has to deal with the very big document inside the row. At that point Its oracle against a big text processing and index has nothing to do.
    How can I speed up the extraction of the section?
    If there any other index or tool for help extraction to be faster?
    I would appreciate to know what can I do. I need help on this.
    Thanks in advance!

    Well,
    - What indexes, if any, already exist?
    - What do the functions rl and nice do?
    - What are the current query plans?
    - How restrictive are the various predicates?
    - What version of Oracle?
    Justin

  • I have a new MacAir and don't know how to get info from my USB stick and my SD photo card.  Can anyone help me please?

    I have a new MacBook Air and don't know how to get info from my USB stick and get info from my SD card.  Can anyone help, please?

    Plug the stick and/or card into the appropriate slots on the side of your Air. Do you see icons for the devices appear on the desktop? Click into them to see what files are there.
    Matt

  • How to read a data from USB port using JAVA

    hi all,
    i need to know how to read a data from USB port using java. any API are available for java ?.........please give your valuable ideas !!!!!!!!!
    Advance Thanks!!

    You can do this. Please use this link
    [http://www.google.co.in/search?hl=en&client=firefox-a&rls=org.mozilla%3Aen-US%3Aofficial&hs=uHu&q=java+read+data+from+usb+port&btnG=Search&meta=&aq=f&oq=]
    What research did you do of your own? Have you done some testing application and tried yourself??

  • How can i create a bootable usb sata for xp

    how can i create a bootable usb sata for xp

    Installing Windows XP on a portable USB hard drive is not supported.
    Carey Frisch

Maybe you are looking for