How do i use a 2nd airport extreme both are newer models

how do i use a 2nd airport extreme both are newer models

I assume that you mean that you want to extend the range using wireless only.
This Apple Support Document will tell you exactly how to do that:
http://support.apple.com/kb/HT4259
The instructions assume that you have AirPort Utility 5.6 for Mac OS X Lion , so if you have not already done so, you will need to download and install this application to track the instructions in the support document.

Similar Messages

  • How do I use a 2nd Airport Extreme plugged into an Ethernet Wall Plug to join an existing wireless network to give me a better signal upstairs?

    I have a 5th generation Airport Extreme giving me a great wireless signal on the 1st floor of my house. However the signal upstairs is weak. So I purchased another 5th generation Airport Extreme that I would like to plug into an ethernet wall plug upstairs. I would then like to have the upstairs Airport Extreme join the same network thus giving me a good wirelss signal upstairs. I have a MacBook Pro running OS 10.7.4. Can somebody give me step-by-step directions to set up the upstairs Airport Extreme?

    I assume that the new AirPort Extreme is still in its original factory default settings.
    Before you connect the AirPort Extreme, please connect a laptop to the Ethernet cable that will be used for the connection and turn off the wireless on the laptop. Make sure that you can can connect to the Internet before you begin to configure the AirPort Extreme.
    Disconnect the Ethernet cable from the laptop and connect it to the WAN "O" port on the upstairs AirPort Extreme and power it up.
    Open Macintosh HD > Applications > Utilities > AirPort Utility 6.1
    Look in the upper left hand corner of the screen for a tab or box that reads "Other AirPort Base Stations (1)"
    Click on that box,then click on the name AirPort Extreme xxxxxx
    Wait a moment while AirPort Utility analyzes the network and then displays a message that the AirPort Extreme will be configured to extend your existing wireless network.
    Enter a Base Station (device) name for the AirPort Extreme (and a device password if prompted), then click Next.
    Wait another minute or two until AirPort Utility notifies you that the AirPort Extreme has been Set Up.
    That's it.

  • How to replace a older Airport Extreme with a newer model? (OS 10.6 w/ Mac Mimi)

    How do I replace a older Airport Extreme with a newer model? (Mac Mini OS 10.6.8 )

    There is not much more to it than to buy a new one, and configure it using AirPort Utility.
    You should be using AirPort Utility 5.6.1.
    Power down your modem before removing your older Extreme and connecting the new one.

  • How can I utilize a 2nd Airport Extreme to extend a network but not WIFI, only hardwired?

    Hi All.  Need your help figuring this out.  The location of the cable line in my home causes a bit of an issue for my internet dependant electronics.  My computers have no problem connecting over Wifi but certain peripherals require an ethernet connection as Wifi is not an option for them.  I have prepared this quick diagram to explain my perfect set up.  I have a current gen Airport Extreme and a Previous gen as well.  How can I set my 2nd Airport to receive the Wifi from my main airport, but then only serve as a router, not extend the WIRELESS network.  Only provide a hardwired network.  In other words, I know how to "extend network" with airport utility, but then the 2nd airport also casts its own wifi network and causes problems.  I only want the one single Wifi network.  The 2nd router should only be providing ethernet connectivity.
    Is this even possible?  Both Airports are running the most updated firmware.  Any advice would be greatly appreciated!!!

    With a properly configured extended network both AirPorts will be broadcasting the "same" Wi-Fi network. This shouldn't impact wired clients at all. The other advantage of using an extended network is that your older AirPort Extreme's Ethernet ports will be enabled for wired clients.
    At present the only other option would be to connect the older Extreme to the newer one using an Ethernet connection between them. Then disable the older Extreme's Wi-Fi radios.

  • I want to replace one of my older Airport Extremes with the new model.  Any tips?

    I have 2 older airport extreems that are connected by a network cable.  They share the same Netrwork ID.
    I want to replace one of them with the new model as I want to use the old router on another project.
    Any tips out there for a no-issue switch?
    Should the newer and faster Extreme be connected  to the Modem or does it nt make a didfference?
    Thanks

    use the new router as your primary router with the modem - this will be a factory  install from the default configuration -   as long as you use same network name password and type a password that you used for the express in bridge mode, you should be able to plug it in and have it work like before.  just make sure that you configure everything individually and then power all devices down and repower each one individually starting with the modem then the router in the express and that should work 

  • How can i use my old airport express with my new imac and wireless hp print

    i just bought my first imac (intel) and a wireless hp printer. i now realize that a wireless connection between my imac and my printer needs a router.
    i have an airport express base station, which is a few years old. I can't find my documentation, so i don't know its specifications.
    how can i find out the specs of the airport express i have and whether i can use it now? it says that it is model a1084 100-240v~ 0.2a 50-60 hz.
    does that tell any knowledgeable people out there about the specs? can i search the apple website by serial number and find the specs?
    thank all of you potential responders ahead of time.

    Hi green jean
    Try this > http://www.apple.com/airportextreme/features/printing.html
    but also see > http://docs.info.apple.com/article.html?artnum=305293
    Dennis

  • How can I strenghten a weak Airport Extreme (2nd Generation) signal?

    I have been having a weak WiFi signal in my Airport Extreme. Even when I am in a room that is less than 30 ft away.
    Here are the details:
    AirPort Extreme 802.11n (2nd generation)
         Version: 7.6.1
         Wireless Mode: Participate in a WDS network
         Wireless Security: WPA/WPA2 Personal
         Channel: 6
         Connect Using: Ethernet
    My Airport Extreme is on the second floor of the house and is connected to a D-Link DIR 825 router that is on the first floor.
    Sometimes when I am on the second floor, I get a better signal from the D-Link router than from the Airpot Extreme.
    How can I strenghten the signal?
    Thanks in advance

    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Click on the AirPort Extreme
    Information about the device will be displayed in the area to the right
    The 3rd Generation product was the first Apple simultaneous dual band router, introduced in March 2009. Minor changes were made in the chipsets between the 3rd Generation and 4th Generation versions with some antenna improvements added in the 4th Generation versions as well. The 4th Generation version was introduced in October 2009.

  • How do I extend my existent airport extreme network by addition of a 2nd airport extreme?

    How do I extend my existent Airport Extreme network by addition of a 2nd Airport Extreme?

    Can you clarify which version of the AirPort Extreme that you have now along with the model that you plan to use as the second device?
    The older "round" AirPort Exteme or the newer "square" version with rounded corners?
    Are you planning to extend using wireless only.....or by connecting the AirPort Extremes using a wired Ethernet connection?

  • How do I set up my Airport Extreme to best use multiplayer games locally

    How do I set up my Airport Extreme to best use multiplayer games with my family. Everyone is located in the same house and uses the same router.
    I have tried a few games but have not  successfully connected  2 players

    That is a weird question, as your GAMES could be interpreted a hundred different ways. Are we talking about third party devices here or what?

  • How many devices can I use with an AirPort Extreme Base Station?

    How many devices can I use with an Airport Extreme Base Station? Devices included a mac, iphone, ipad and pc laptops.

    The AirPort Extreme will support up to 50 wireless devices and 200 wired Ethernet devices. I would imagine that this would probably be adequate for most homes.

  • How to set up 6th Generation AirPort Extreme to cable modem as a wireless router and then connect my 3rd Generation Time Capsule to AirPort Extreme as a wireless extender?

    What is the best way to set up my 6th Generation AirPort Extreme (A1521) to my cable modem as a wireless router and then connect my 3rd Generation Time Capsule (A1355) to my AirPort Extreme as a wireless extender? I live in a small 1 story house and I currently have the Airport Extreme connected to my cable modem in the living room and the Time Capsule plugged into the wall in my bedroom. I am able to wirelessly connect to the internet using the AirPort Extreme as my router and I can also do wireless back ups to my Time Capsule. My problem is that my connection seems to be really slow! My 1TB Time Capsule back up is only half way complete and it has been 3 days! My computer has been backing up all day and night for almost 72 hours and its still not even 75% complete. I have backed up to this Time Capsule in the past and it never took this long. I am thinking that when I set up my AirPort Extreme and Time Capsule using AirPort Utility I must have set it up incorrectly or something.
    How do I set up my Airport Extreme and Time Capsule for the fastest possible internet speed and back up speed?
    Thank you,

    AirPort Utility 5.6 works with AirPort Extreme 802.11g base stations.
    It works with N version airports.
    It will also show details of the AC model but cannot be used for the setup.. mostly.
    I purposely got the new 6th Gen Airport Extreme so my internet connection would be a lot faster!
    Your network will be much faster when you have AC client directly connected to the AE. Older client will go no faster.. but what is worse.. extend wireless is mixing new and old wireless standards.. guess what one wins.. OLD.. So when you extend wireless.. you have no improvement whatsoever. This whole post is about extending wireless.. so you cannot extend to older equipment and do any better.. maybe slightly better signal although from your comments that isn't happening either.
    I would rather not have to use an ethernet at all with the TC and I don't know EOP adapters are!
    If you do not use ethernet then you are going to be forced to accept slow speed.
    EOP (ethernet over power). Also called homeplug in the US.
    http://en.wikipedia.org/wiki/HomePlug
    Provides a method of networking over power cabling that already exists in your house.
    So what your saying is for the fastest internet speed and back up speed possible I should keep my Airport Extreme plugged into my Modem and keep my TC set up as a wireless extender? Then when I want to do back ups I should plug an ethernet cable from my TC to my MacBook Pro?
    To spell this out.
    A wireless link to an extended device will go very slowly.. if it is not direct.
    So lets say you have a laptop sitting in the lounge.. Your connection goes.. Laptop- - - - - AE- - - - -TC.
    That means two wireless links.. wireless has this nasty half duplex and single channel nature.. it can send or receive (Tx or Rx) but not at the same time.
    Ethernet by contrast does both at once. It is full duplex.
    Wireless can talk to one client at a time.. so if there are multiple items using wireless lets say 4 devices.. then your computer gets a 25% time slice. Since wireless cannot handle multiple simultaneous connections.
    Ethernet by contrast can connect multiple computers to multiple destinations at the same time.. all transmitting and receiving at full speed.
    When you put all this together.. there are a couple of rules for fast connection.
    1. Use ethernet at all times. Where you cannot use ethernet use anything but wireless.. eg EOP (homeplug) at least to try and get rid of wireless.
    2. Where you must use wireless use it sparingly and make sure it is never more than one hop.. ie never have an extend wireless (repeater is more usual term). Repeater will cause instant slowdown of 50% and maybe up to 75% just because it is so inefficient.
    3. Fastest wireless is 5ghz but it has very short range.. you need to be up close and personal to get it working.
    Apple routers however unless you do manual setup I suggest are set to connect to best signal strength not best speed. It will therefore use 2.4ghz at 25% less speed than 5ghz because it is 1db better signal.. this madness means you need to setup manually for the best setup.

  • Network issue using Time Warner, Airport Extreme, MacBook Pro OSX, Windows7

    I have the following on my home network:
    - Time Warner cable-internet and phone service.
    - Apple Airport Extreme Base Station hooked up to the cable modem
    - MacbookPro running OS 10.6.3 connected wirelessly to airport extrm
    - HP Laptop running Windows 7 connected wirelessly to airport extrm
    - HP Officejet Pro 8500 connected to wirelessly to the airport extrm
    - iPhone connected wirelessly to the airport extrm
    - XBox connected via ethernet cable to airport extrm
    - USB external hard drive connect via USB cable to airport extrm
    My network worked fine with only my Macbook Pro, Airport Extreme, iPhone, XBox, and occasionally my buddy's Macbook Pro all on the network at the same time.
    I recently added an HP Laptop running Windows 7 and a wireless HP Printer to the network at the same time.
    Now if both the Windows 7 PC and the Macbook Pro are on the network at the same time, one of the machines will get booted from the internet. At one point, I got a message on my MacBook Pro that said another computer on the network is using the same IP address. I also have trouble communicating with the new HP printer if both the Windows 7 and the Macbook Pro machines are on the network at the same time.
    How should I set up my airport extreme to allow all machines to function properly on my network. Right now, the network is set up to receive IP addresses automatically through the DHCP server. I read somewhere that maybe setting up the computers to manual static IP addresses and manually entering in the DNS server info into the airport extreme may fix my problem. I also read that configuring the network to all share a single IP address will fix the issue. How do I set this up. I would also like to keep my network invisible from being seen. Is this still possible?
    Thanks for your help on this!!

    To change the IP address on a Mac, go to settings, then select the network interface you use, then, change Automatic to manual. I don't know how to do this on windows 7, and you can access and change your printers settings by clicking in the bookmark windows on Safari, clicking printers, and open up it's settings.

  • Can I use an old Airport Extreme as an extender with a new Airport Express

    Hi All,  I have Verizon Fios and the data line runs into my bedroom.  I purchased a new Airport Express today to replace the Airport Extreme (from 2006).  Can I use the old Airport Extreme as an extender (I'd like to set it up in the basement as I get poor connectivity there).  I tried using the Airport Utility - Other WiFi Devices to find the Airport Extreme, but it's not registering. Is what I'm attempting possible?  If so, how do I set it up?

    Can I use the old Airport Extreme as an extender
    Is this the "round" or "dome" shaped AirPort Extreme?
    If yes, then it is not possible to have the AirPort Extreme wirelessly "extend" the signal from the AirPort Express.
    However, the older AirPort Extreme can probably be set up to provide more wireless signal coverage if it will connect back to the LAN <--> port on the AirPort Express using a permanent, wired Ethernet cable connection.
    In this case, the setup of the older AirPort Extreme will require that you have an older version of AirPort Utility installed on your computer. If it is a Mac, then the Mac must be running Leopard (10.5.x), Snow Leopard (10.6.x), or a PC with AirPort Utility could be used to set up and configure the older Extreme.
    f you have the "square" or "flat" version of the AirPort Extreme, then everything becomes much easier. Post back if you do.

  • Airport Extreme 5Ghz with 2nd Airport Extreme

    I currently have a Airport Extreme Base Station (Latest model).
    I have it connected to an Airport Express.
    I would like to purchase another Airport Extreme and set this in Bridge Mode. I have it connected to an 8 port switch which is in turn connected to the original Airport Extreme.
    If I have two Airport Extreme's will I get Wi-Fi via 5Ghz on 5Ghz capable devices?
    What happens when a 2Ghz device connects to the network?
    Most importantly can I use this new 2nd Airport Extreme's 3 additional ports to connect a local computer and printer?
    If I use my Airport Express will this kill the 5Ghz network?
    Thanks,

    Can the Airport Express be set up as a PRINT SERVER only with no networking configuration?
    No, the Express needs to be configured as a client on the network to act as print server
    I noticed teh 5Ghz range is limited compared to 2.4Ghz range. Is there a rule of thumb on range between the two?
    5 GHz signals are much weaker than 2.4 GHz signals, so they do not penetrate obstructions well. In general...for good performance....5 GHz is pretty much of a line-of-sight deal between the router and computer.
    I am assuming I set the 2nd Extreme in Off (Bridge Mode) to turn it into an Access Point?
    Yes
    Why do I see IP address from devices located on the 2nd floor near the 2nd Extreme in Bridge Mode connected to the 1st Extreme in the basement?
    You are seeing wireless devices that are using the wireless on the 2nd Extreme, but the IP addresses have been issued by the 1st Extreme. You can confirm by checking all DHCP Clients on the 1st Extreme.

  • Currently use Airport Express -1st Generation-to access internet -purchased 2014 Airport Extreme base station -can I import Express back up configuration to keep current settings . Or is it best to do new Airport Extreme as a new Network .

    Currently use Airport Express -1st Generation-to access internet -purchased 2014 Airport Extreme base station -can I import Express back up configuration to keep current settings . Or is it best to do new Airport Extreme as a new Network .

    Just spoke with Cisco about the router.  They said the router is compatible with the E1500.  They suggested that I contact Apple to see if their default IP address was that same as the router (192.168.1.1).  They told me I would have to change it if that was the case.  How would I do that?

Maybe you are looking for