How to change host name and domain name in installed Cisco Meeting Place Express 2.0?

Hi
I have  Cisco Meeting Place Express 2.0 installed on server. Meting Place uses Linux (Red Hat) as base operation system. Please tell me how I can change host name and domain name for Meeting Place Express application to integrate it into corporate domain infrastructure.
Thanks in advance!!!
Sincerely yours
Sergey Bondarenko

Hi
Thanks for your attention for my humble problem.
I have performed Meeting Place Express configuration through the “net” command.
But now unfortunately I can't connect to meeting place through web browser. I just get blank page.
Though I can reach the server with help of ssh. I think my DNS works properly because I can resolve the ip address of  cumpxvoice .uclab.com and cumpxweb. uclab.com with help of dig command.
Have you any idea?
A lot of thanks in advance!!
Sincerely yours Sergey Bondarenko
Here I have printed the net configuration output of Cisco meeting Place Express:
[root@cumpxvoice root]# net
This is the MeetingPlace Express network configuration utility.
Up to the point where you save changes, it is safe to hit ^C to get
out at any time, in which case nothing will have changed.
1) List current configuration
2) Configure Ethernet port 1
3) Configure Ethernet port 2
4) Configure service bindings
5) Set host names
6) Set domain name
7) Configure DNS service
8) Configure NTP service
9) Configure routing
10) Done
Select: 1
Primary/audio host name: cumpxvoice
HTTP host name:          cumpxvoice
RTMP host name:          cumpxweb
Domain name:             uclab.com
Service bindings:
Audio:                   port 1 (eth0)
Web browsing (HTTP):     port 1 (eth0)
Web conferencing (RTMP): port 2 (eth1)
Port 1 (device eth0):
IP Address:      10.62.60.116
Network mask:    255.255.255.0
Default gateway: 10.62.60.1
Link setting:    autoneg on
Port 2 (device eth1):
IP Address:      10.62.60.117
Network mask:    255.255.255.0
Default gateway: 10.62.60.1
Link setting:    autoneg on
Static routes:
Destination      Gateway          Network mask     Port
0.0.0.0          10.62.60.1       0.0.0.0          1
DNS Servers:
10.62.60.115
10.0.1.4

Similar Messages

  • How to change IP, Hostname and domain name for Oracle Application R12

    Hi,
    I'm new to Oracle, we used to have one production and one test server for Oracle Application R12, but the test server was corrupted, so we decided to clone production server and create a new test server, after cloning and creation of test server, how should we do to change IP address, hostname and domain name for test server?
    Our production and test server environment is:
    Linux Enterprise AS 2.6.9
    Application module: E-Business Suite Treasury only
    Your advice will be much appreciated.
    Regards,
    Kenneth
    Edited by: 850209 on Apr 7, 2011 5:37 PM

    850209 wrote:
    Hi,
    There are few tnsnames.ora and listener.ora files in the system, how to know which one are effective? If I change tnsnames.ora hostname entry, do I need to change listerner.ora file also?
    Thanks.
    Regard,
    Kenneth.tnsnames.ora is used only by client processes. listner.ora is used only to configure the listener, and that is a server side issue only. In addition, the listener can start without any listener.ora at all, using all default values. See my discussion of tns issues at edstevensdba.wordpress.com
    If you are using dbcontrol, you will most likely need to reconfigure it, using the emca utility.

  • Change Groupwise system name, po name and domain name?

    Hello Board,
    we want to migrate a Groupwise 7 System (Netware) to a Groupwise 8 System (Linux).
    Doesnt sound that difficult, but we dont want to use the names for the system name, the post office and the domain (groupwise domain, _not_ internet domain) which were used on the old system.
    Currently iam trying the way mentioned in TID 10077372, which mentions merging the two systems and then delete the old System.
    Am i on the right way? Do you have any hints?
    Any help appreciated.
    best regards
    sven

    Grewes,
    Ok you have a GW system(s) that you do not like the names and you want to change them. Not a problem. As you stated, and as Tommy said -merging works.
    The process you need is to build a new GW system -same as the version you have running preferred. Set it up as you like it -name-wise. Then, merge the older systems (branches) into the new system you built. Then you will have to build new domains/post offices and move mailboxes from the old GW branches into the new domains/post offices. When its all done -delete the old, and you are done.
    I have done many different variations of this type of migration/merge/consolidation. It works, its just a lot of work. Just make sure to plan it all out on paper first, document it, then go forward.
    Good Luck!
    Take Care.
    Gregg A. Hinchman
    Consultant
    [email protected]
    www.HinchmanConsulting.com
    A Novell Consulting Partner
    317.329.0288 Office
    413.254.2819 eFax
    "Courage is doing what is right."
    "Do not be bound to any doctrine, theory or ideology, even Buddhist ones. All systems of thought are guiding means, not absolute truth." Thich Nhat Hanh, Vietnamese monk.
    Book Travel @: www.booknewtravelnow.com
    >>>
    From: grewes<[email protected]>
    To:novell.support.groupwise.migrations
    Date: 8/20/2009 6:56 AM
    Subject: Re: Change Groupwise system name, po name and domain name?
    Thank you for your reply.
    I do not want to keep the names.
    If i want to link this domain to another branches domain and the domain
    is called the same this doesnt work AFAIK.
    grewes
    grewes's Profile: http://forums.novell.com/member.php?userid=3563
    View this thread: http://forums.novell.com/showthread.php?t=383606

  • Difficulty changing computer name and domain name

    I have a working Xserve with the latest Snow Leopard Server and am having difficulty reconfiguring it from its keyboard.
    I would like to edit the computer name and domain name and maintain all other server settings. I would prefer to do this off-line. However Server Admin appears not to work off-line and any attempt to change computer name or domain name removes all server settings from view including the serial number. I can recover everything by reinstating computer name etc and restarting on-line.
    Is the serial number tied to the computer name and/or domain name?
    Is there any way to retain my existing server settings for a different domain?
    Is there any way to progress any of this off-line?

    This has now been resolved. This note is to assist others who have the same problem.
    1 - I had been changing the computer name in the place I had always done it - System Preferences/Sharing. This confused Server Admin. Reverting to the original name and changing computer name and location within Server Admin resolved the issue. That is System Preferences/Sharing is updated by Server Admin but not vice versa.
    2 - Playing with these things can corrupt Server Admin plist resulting in a restarted Server Admin not seeing the edited server even with the server otherwise fully functioning. Trashing Server Admin plist resolved this for me without loss of server settings.
    3 - Having set it up off-line I experienced difficulty as soon as I went on-line. This was resolved by changing the server from 'local' to its full domain name. I have no explanation for this as the same settings had previously worked with 'local'.
    4 - Server Admin can take a long time to find settings and occasionally failed to do so until after a restart.
    The result can be seen here: http://links.open.ac.uk/ - Since Apache refuse to provide hit counter support (there are several public posts of mine on the subject) I use JavaScript to retrieve the count from an old QPQ server running on a G3 with OS 9.

  • Cisco Meeting Place Express 2.1.1.2 and not working anymore

    Hello, we currently have cisco meeting place express 2.1.1.2; however are now having issues with it.  We are unable to dial to the internal extension that was previously working to login to the meetings and only get a busy signal everytime. Furthermore, whenever someone tries to schedule a new meeting via the web form, it says "request to server timed out. please try again".
    I tried reaching out to Cisco TAC support; however it's no longer a supported item and am looking for assistance here.  The TAC engineer was able to help assist with updating the system clock; however I believe the problems started happening after we updated the clock and rebooted the server.  Now we are unable to schedule and attend any meetings (busy signal everytime) at all.  I tried restarting the server itself as well as via the command line.  I also now see an error during CLI restart, which I have listed directly below:
    Stopping MeetingPlace SNMP/R:                              [  OK  ]
    Stopping mpe-tomcat-main: bash: /root/.bashrc: Permission denied
                                                               [  OK  ]
    Stopping mpe-tomcat-securewebservices: bash: /root/.bashrc: Permission denied
                                                               [  OK  ]
    Shutting down breeze:                                      [  OK  ]
    Shutting down fmsmaster:                                   [  OK  ]
    Shutting down fmsadmin:                                    [  OK  ]
    Stopping MeetingPlace application: /etc/init.d/mpx_app: line 264:  4955 Segmentation fault      (core dumped) ${shutdown_bin} ${shutdown_arg_1} ${shutdown_arg_2} ${shutdown_arg_3} >>${non_verbose_shutdown_output} 2>&1
                                                               [FAILED]
        ERROR: returncode = 139
    Stopping MeetingPlace License Manager:                     [  OK  ]
    Stopping MeetingPlace database:                            [  OK  ]
    Stopping MeetingPlace Java RMI: Shutting down RMI Registry:
                                                               [  OK  ]
    Stopping Cisco MeetingPlace Express:                       [  OK  ]
    Starting MeetingPlace Java RMI: Starting RMI Registry:
    starting daemon
    mpxadmin
                                                               [  OK  ]
    Starting MeetingPlace database:                            [  OK  ]
    Starting MeetingPlace License Manager:                     [  OK  ]
    Starting MeetingPlace application:                         [  OK  ]
        already running
    Starting breeze:                                           [  OK  ]
    Starting fmsmaster:                                        [  OK  ]
    Starting fmsadmin:                                         [  OK  ]
    Starting mpe-tomcat-main: bash: /root/.bashrc: Permission denied
                                                               [  OK  ]
    Both the admin and user web interfaces work on the home pages, but can't seem to schedule any new meetings or login to any existing ones, with busy signal as well. Anyone have any ideas? We need assistance with this ASAP since it's our voice collaboration solution.  Thanks in advance for any help.                  

    Amlesh,
    Here is the pertinent output:
    /common/log/taos-log-a/core/core.1947.11.ConfSchd.1183266069
    /common/log/taos-log-a/core/core.1837.6.gyromain.bin.1183266161
    /common/log/taos-log-a/core/core.1859.6.cpgs.1183266206
    /common/log/taos-log-a/core/core.1951.11.ConfSchd.1184475669
    /common/log/taos-log-a/core/core.1946.11.ConfSchd.1185685269
    /common/log/taos-log-a/core/core.1836.6.gyromain.bin.1185685332
    /common/log/taos-log-a/core/core.1880.6.cca.1185685452
    /common/log/taos-log-a/core/core.1858.6.cpgs.1185685452
    /common/log/taos-log-a/core/core.1950.11.ConfSchd.1185771671
    /common/log/taos-log-a/core/core.1863.6.cpgs.1185771865
    /common/log/taos-log-a/core/core.1884.6.cca.1185771865
    /common/log/taos-log-a/core/core.1991.6.nmpagent.1185771865
    /common/log/taos-log-a/core/core.1950.11.ConfSchd.1185858067
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1188018079
    /common/log/taos-log-a/core/core.1969.11.ConfSchd.1188190869
    /common/log/taos-log-a/core/core.2008.6.vui.1188190988
    /common/log/taos-log-a/core/core.2029.6.nmpagent.1188190988
    /common/log/taos-log-a/core/core.1998.6.poclient.1188190988
    /common/log/taos-log-a/core/core.1970.11.ConfSchd.1189227671
    /common/log/taos-log-a/core/core.1862.6.gyromain.bin.1189227762
    /common/log/taos-log-a/core/core.1883.6.cpgs.1189227807
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1189918866
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1190005281
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1190178068
    /common/log/taos-log-a/core/core.1886.6.cca.1190178237
    /common/log/taos-log-a/core/core.2012.6.nmpagent.1190178237
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1191906070
    /common/log/taos-log-a/core/core.1843.6.gyromain.bin.1191906162
    /common/log/taos-log-a/core/core.1886.6.cca.1191906248
    /common/log/taos-log-a/core/core.1865.6.cpgs.1191906248
    /common/log/taos-log-a/core/core.1950.11.ConfSchd.1192424479
    /common/log/taos-log-a/core/core.1842.6.gyromain.bin.1192424571
    /common/log/taos-log-a/core/core.1863.6.cpgs.1192424613
    /common/log/taos-log-a/core/core.1951.11.ConfSchd.1192597270
    /common/log/taos-log-a/core/core.1969.11.ConfSchd.1192683669
    /common/log/taos-log-a/core/core.1903.6.cca.1192683817
    /common/log/taos-log-a/core/core.1951.11.ConfSchd.1193029270
    /common/log/taos-log-a/core/core.1842.6.gyromain.bin.1193029360
    /common/log/taos-log-a/core/core.1864.6.cpgs.1193029400
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1193720467
    /common/log/taos-log-a/core/core.1843.6.gyromain.bin.1193720565
    /common/log/taos-log-a/core/core.1864.6.cpgs.1193720610
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1195452071
    /common/log/taos-log-a/core/core.1843.6.gyromain.bin.1195452170
    /common/log/taos-log-a/core/core.1864.6.cpgs.1195452213
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1196834481
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1197007273
    /common/log/taos-log-a/core/core.1842.6.gyromain.bin.1197007371
    /common/log/taos-log-a/core/core.1864.6.cpgs.1197007413
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1198044080
    /common/log/taos-log-a/core/core.1843.6.gyromain.bin.1198044184
    /common/log/taos-log-a/core/core.1842.6.gyromain.bin.1199858530
    My understanding is these core files are crash dumps and are safe to delete?
    Jared

  • Apps 11i , Need to change Host Name and Domain Name after Install

    Hi,
    I have installed 11.5.10.2 on Windows. Now I need to change the Host and Domain of the instance.
    Please advise.
    Regards
    Tauseef

    Hi,
    Please refer to:
    Note: 338003.1 - How to change the hostname and/or port of the Database Tier using AutoConfig
    Note: 341322.1 - How to change the hostname of an Applications Tier using AutoConfig
    Regards,
    Hussein

  • How to protect my company name and domain names

    Hi All
    I have just been approached via email from a company in China wanting to use my company name for their client and asking if it has been registered.
    It hasn't and I am now extremely worried and not sure what to do. I have been trading under this name for 2 and half years and have my domain name under the company name too.
    Does anyone know if they can take this from me if they register the same name?
    Tracey

    You do have to be careful that your domain doesn't expire—you have to pay the yearly fee or it will be available to anyone. If you've lost track of where it's registered or when it expires, you can look it up here:
    Whois Lookup & IP | Whois.net

  • How to change the full host and domain name on OS X Leopard...

    I recently bought an iMac, and I'm trying to configure it for my network. The question I have is, how can I change the host name and domain name from Skuld.local to skuld.tolharadys.net?
    After mucking around with a few searches on Google, I've gotten the domain name to stick since running domainname returns tolharadys.net. Also I can change the hostname as reported by 'hostname' temporarily by running 'hostname skuld.tolharadys.net' in Terminal.app. However, this isn't persistent after reboots. Ideas are welcome.

    You would need a DNS server on your network configured to answer authoritatively for that particular subdomain.

  • Change Db name and Instance name in *i

    Following is the procedure how i changed the DB and instance name
    1Alter database abckup controlfile to trace;
    2.Edit the trace file to create a new file
    create a instance with diff SID(New sid)
    startup nomount
    edit the initora.file
    changed the instance and db_name in Init.ora
    edit the controlfile with resetlogs option and set dataabse name
    alterdatabase open tresetlogs
    shutdown backup
    Is it correct?
    looks correct to me
    aything i missed out?

    edit the init.ora and then startup nomount and then execute create controlfile command and then open db.

  • Need to the domain name and computer name in offline mode

    Hi,
    I can not able to login to the windows system, the password i am using is correct. But im getting error "the login method using is incorrect, please contact network admin". I forgot the domain name i set to login to the system. Now Currently i
    dont have the recovery/windows7 disks.  I have Unix in my machine as well. so i have mounted the windows7 parition in linux, and trying to find out the computer\domain name.  so please suggest which file i need to search to get the details.
    Thanks,
    Ravi

    Hi Ravi,
    If you want to know more information about domain name, please take a look at the following article.
    http://technet.microsoft.com/en-us/library/cc731265(v=ws.10).aspx
    Based on my research, the computer name and domain name are stored in the registry key.
    We could find computer name in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\ComputerName\ComputerName.
    And we can find domain name in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Domain.
    Have you ever  joined a domain?
    If yes, please contact the network admin as mentioned.
    And we can type Domain name\Username and then password to login.
    If you haven’t, we could try to type Computer name\username(.\username) and then the password to login the computer.
    Best regards,
    Fangzhou CHEN
    Fangzhou CHEN
    TechNet Community Support

  • How to change Host and domain name on APS 10g R2

    Hi,
    I have installed oracle application server 10g rel.2 I want to change the host and domain of the system, what should I do, Plz help.
    Thanks and Regards.
    Khawar

    Hi,
    Thanks to all of you for reply, I started without reading any manual to modify host and domain name and after expending several hours finally decided to reinstall APS, with new installation forms runing ok but report server having problem if you see the status of report server in enterprise manager it shows green mark(if you want to stop it via EM it will not), if you check with Report Queue manager it says no report server with the given name,
    if you check the report with GETSERVERINFO via browser it says
    "REP-51002 Bind to report server AAAAA failed. some one have idea."
    some one plz explain me how can I fix it.
    Thanks and Regards.
    Khawar

  • Server host and domain name have changed, which files do I edit?

    I just changed my Linux box server name and host name. I am going to edit the:
    tnsnames.ora
    sqlnet.ora
    listener.ora
    files to reflect the new host and domain name, are these the only files I need to edit?
    Thanks!

    OK here is my output when I try 2 different tnsping commands on my remote Linux box from my local PC:
    1.)
    C:\Documents and Settings\Rick>tnsping db.host.mtdomain.com
    TNS Ping Utility for 32-bit Windows: Version 9.2.0.1.0 - Production on 13-NOV-2005 07:38:55
    Copyright (c) 1997 Oracle Corporation. All rights reserved.
    Used parameter files:
    C:\oracle\ora92\network\admin\sqlnet.ora
    TNS-03505: Failed to resolve name
    2.)
    C:\Documents and Settings\Rick>tnsping mydomain.com
    TNS Ping Utility for 32-bit Windows: Version 9.2.0.1.0 - Production on 13-NOV-2005 07:36:07
    Copyright (c) 1997 Oracle Corporation. All rights reserved.
    Used parameter files:
    C:\oracle\ora92\network\admin\sqlnet.ora
    Used HOSTNAME adapter to resolve the alias
    Attempting to contact (DESCRIPTION=(CONNECT_DATA=(SID=*)(SERVICE_NAME=mydomain.com))(ADDRESS=(PROTOCOL=TCP)(HOST=mydomain.com)(PORT=1521)))
    OK (250 msec)
    Here are my sqlnet.ora, listener.ora, and tnsnames.ora
    # SQLNET.ORA Network Configuration File: /home/oracle/Oracle9i/product/9.2.0/network/admin/sqlnet.ora
    # Generated by Oracle configuration tools.
    NAMES.DEFAULT_DOMAIN = host.mydomain.com
    NAMES.DIRECTORY_PATH= (TNSNAMES, ONAMES, HOSTNAME)
    # LISTENER.ORA Network Configuration File: /home/oracle/Oracle9i/product/9.2.0/network/admin/listener.ora
    # Generated by Oracle configuration tools.
    LISTENER =
    (DESCRIPTION_LIST =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC))
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = host.mydomain.com)(PORT = 1521))
    SID_LIST_LISTENER =
    (SID_LIST =
    (SID_DESC =
    (SID_NAME = PLSExtProc)
    (ORACLE_HOME = /home/oracle/Oracle9i/product/9.2.0)
    (PROGRAM = extproc)
    (SID_DESC =
    (GLOBAL_DBNAME = db9i)
    (ORACLE_HOME = /home/oracle/Oracle9i/product/9.2.0)
    (SID_NAME = db9i)
    # TNSNAMES.ORA Network Configuration File: /home/oracle/Oracle9i/product/9.2.0/network/admin/tnsnames.ora
    # Generated by Oracle configuration tools.
    DB.host.mydomain.com =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = host.mydomain.com)(PORT = 1521))
    (CONNECT_DATA =
    (SERVICE_NAME = db)
    EXTPROC_CONNECTION_DATA.host.mydomain.com =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC))
    (CONNECT_DATA =
    (SID = PLSExtProc)
    (PRESENTATION = RO)
    INST1_HTTP.host.mydomain.com =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = 127.0.0.1)(PORT = 1521))
    (CONNECT_DATA =
    (SERVER = SHARED)
    (SERVICE_NAME = MODOSE)
    (PRESENTATION = http://HRService)
    )

  • How to change the name / IP address and domain name for BOE Server

    Hello,
    We want to change the name / IP address and domain name for BOE Server, please could you indicate the steps or procedure to follow?
    I need your help
    thank you

    If it's 3.1 just change them, shouldn't cause any issues if by domain name you are referring to changing the domain the computer belongs to. If you are changing your domain for AD authentication then you will may have to take quite a few steps if the old domain is going away. Let us know.
    Regards,
    Tim

  • How to change host name for management agent.

    Hi,
    I 've installed management agent for oracle, it's a part of Oracle Management Framework, but I have to change host name.
    I know how to change port number, but I've no idea how to change host name.
    Have you got any idea?
    Thank you in advance.
    Matin

    Hi,
    you can change it in System Landscape directory.
    Go to the http:yourportal.com:50000/sld
    then click on the Landscape and update the new host name.
    Raghu

  • OS X Server clients can't login after IP renumber and domain Name change

    I can not seem to get the logins working again on my OS X server (10.9.4 w/ server 3.1.2 on a 1 yr old. MacMini) after I needed to renumber the IP and change the domain name. I destroyed the Open Directory server, recreated it and created one test account. If I log in to the client with a local account I can connect to the server (Go>Connect To Server)  from the client using my newly created account, but when I try to login to the server  using the same network account login I get the "shaking head" response immediately. I have rebound the server to this client and it says that network accounts are available, but seem to be at a loss to understand why it won't let me login...
    The only error message I see in any of the logs is the following:
    (AFP Error Log:) Sep 15 20:21:47 isis.mydomain.com AppleFileServer[3032] <Info>: major error <1>: No credentials were supplied, or the credentials were unavailable or inaccessible.
    I'm not sure what credentials it is referring to. I created a self signed certificate that I am using with OD, could that be the one?

    Many Open Directory problems can be resolved by taking the following steps. Test after each one, and back up all data before making any changes.
    1. The OD master must have a static IP address on the local network, not a dynamic address.
    2. You must have a working DNS service, and the server's hostname must match its fully-qualified domain name. To confirm, select the server by name in the sidebar of the Server application window, then select the Overview tab. Click the Edit button on the Host Name line. On the Accessing your Server sheet, Domain Name should be selected. Change the Host Name, if necessary. The server must have at least a three-level name (e.g. "server.yourdomain.com"), and the name must not be in the ".local" top-level domain, which is reserved for Bonjour.
    3. The primary DNS server used by the server must be 127.0.0.1 (that is, itself) unless you're using another server for internal DNS. The only DNS server set on the clients should be the internal one, which they should get from DHCP if applicable.
    4. Follow these instructions to rebuild the Kerberos configuration on the master.
    5. If you use authenticated binding, check the validity of the master's certificate. The common name must match the hostname and domain name. Deselecting and then reselecting the certificate in Server.app has been reported to have an effect in some cases. Otherwise delete all certificates and create new ones.
    6. Unbind and then rebind the clients in the Users & Groups preference pane. Use the fully-qualified domain name of the master.
    7. Reboot the master and the clients.
    8. Don't log in to the server with a network user's account.
    9. Disable any internal firewalls in use, including third-party "security" software.
    10. If you've created any replica servers, delete them.
    11. As a last resort, export all OD users. In the Open Directory pane of Server, delete the OD server. Then recreate it and import the users. Ensure that the UID's are in the 1001+ range.

Maybe you are looking for