How to configure a Proxy in OSB with Digest Authentication?
Hello, Guys.
I need a help with this subject.
I have a demand to configure a Proxy in OSB 11.1.1.6 with Digest Authentication. I'm using a Embedded Ldap with Identity Asserter.
I'have configured a DefaultAuthenticator and the DefaultIdentityAsserter to support Digest Password and create a new LdapIdentityAsserter pointing to my embedded Ldap.
When I'll create a new Proxy, in the security options, i can see the digest options to authenticate my username and password. I selected the one of all the options, but in the time of the Proxy test the authentication didn't work.
Could anyone help me?
Thanks you.
Unfortunately, a reference trigger can't be used for continuous acquisition after the trigger. The maximum post-trigger count is either 2^24 or 2^32 depending on your hardware. Depending on your sampling rate and how many samples you expect to acquire before issuing a software stop, using the max post-trigger count may be sufficient for you. There are a couple of other options I can think of that you might want to try:
1.) If possible, play with the trigger condition such that it occurs at the start of your pre-trigger data and use it as a start trigger instead. I suspect this may not be possible.
2.) Set up a continuous acquisition and implement detection of the trigger condition through software. This is more software work and is more CPU intensive than the hardware solution, but it can definitely be made to work.
3.) With some creative use of the counters, you may be able to latch the sample clock number that trigger occurred on. This would allow you to setup a continuous acquisition and use the hardware to tell you where the trigger occurred instead of figuring it out in software. What I'm thinking is you would set up a buffered event counting task with the ai/SampleClock as the timebase source of the counter and the trigger signal as the sample clock of the counter. By reading the first count value, you should know which AI sample the trigger occurred. From there, you can seek to the right position in the buffer and begin reading data indefinitely.
Good luck!
Similar Messages
-
How to configure Security services in OSB 11g..
We are integration OSB with BANK application, we will be using SSL certificate for the same.
Please help how to configure security policy in OSB.
I checked below link policy defination
http://tim.blackamber.org.uk/?p=825
but in OSB proxy service we are not able see Policy button.
Please help.
Thanks,
MihirPlease post your query in SOA Suite forum -
SOA Suite
Regards,
Anuj -
How to configure a new product type with a new operation deal?
hello, All,
I wonder to know if somebody knows, how to configure a new product type with a new operation deal with the amortization divided?, I mean in the SPRO, portfolio of securities with the characteristics mentioned.
Hope you help me.
Bests regards.Hi Prasad,
Thanks for the information, but the directions that you give me not be useful, I want that the UPDATE TYPE appears in the position cash flow in the transaction deal in the option-->operative valuation area( 2nd option) or in the report TPM13, this for two treasury ledger dates.
I mean that the update type "samxx" affect the accountant as amortization divided?, this transaction deal is a purchase.
Thanks in advanced -
How to configure SMTP server for osb 10.3.1
Hi All,
Can anyone share information on how to configure SMTP server for osb 10.3.1
and then how to send an email from osb 10.3.1
Thanks in Advance!!Thanks a lot!!
I configured the same way. When I am sending email to an account on the same domain as my SMTP server is the sending of email is successful. But its giving error when I am trying to send an emain to an account which is on different domain. It giving error as "Operation has been cancelled"
Please suggest something. -
How to configure a proxy server for Windows Azure Tools in Visual Studio 2013
Hi Visual Studio/Azure Tools team
I would like to use the Windows Azure tools in Visual Studio 2013 to manage my Azure Web sites (Server Explorer -> Windows Azure -> Web Sites) from within my corporate network which is secured using a proxy server. Unfortunately, I am not able to use
the Windows Azure tools since the required HTTPS connection to windows azure is not going through the default configured proxy. Instead, Visual Studio tries directly to connect to port 443 which is blocked by our corporate firewall (and yes: there is no way
around using our proxy server). Other visual studio features like NuGet, updates, etc. work fine and use the configured proxy server.
So my question: How can I configure visual studio respective its Azure tools to use a proxy server instead of a direct connection? I already tried configuring the proxy server within the file devenv.exe.config but this doesn't show any effect for Windows Azure
tools.
Regards
tschaenaAs we have very similar problems I consider the found solution a work arround an existing problem which will not work if corporate FW policy does not allow such changes.
In my mind, any tools in charge of dealing with some sort of FW protocols should deliver the following information, should make it absolute clear how to setup that the request packages are setup rigth at the first time.
a) proxy server
b) proxy port
c) proxy user
d) proxy users-password
e) proxy.auth.Preference="BASIC"
And for moste tools (including Visual Studio and AZUR Tools) it is absolut unclear
a) how to setup that on a per tools basis
b) OR who inherits this information from whom i.e. use the same as IE does, what if we use FireFox or any other browsers?
I understand that developers requested to cure such problem areas will often have difficulty to gain all required elemenst used to realy test the solution.
But I can tell you: I loos more time figthing down the FW setups for my clients. WHat I do at home in a sniff, takes ages to be realised by all the various clients on the market where each has to deliver the same sort of information but actually does not,
or has it just somewhere, but not in the vicinity of the demanding user.
Good examples i.e. NetBeans IDE where the Option Menu shows very clearly what information is required to pass through a FW/Proxy; but even there, the hint to start with a BASIC authentication schema is not part of this OPTION menu and must be added a JAVA
environment value. But at least, it works.
Sepp -
How to configure internet proxy for portlet builder
Hi All,
We have downloaded the portlet builder from developer.bea.com. But while trying
to access xmethods for adding web service, it can't access as the internet connection
is thru proxy.
Can anybody pls tell me how to configure the internet proxy with this portlet
builder ?
TIA,
SudarsonHi, I got the same problem...I try to configure a web service with Portal Builder
7.0 in Bea E-Business Control Center... But I can not proceed cause there is no
hint for a proxy... Have you found a solution?
"sudarson" <[email protected]> wrote:
>
Hi All,
We have downloaded the portlet builder from developer.bea.com. But while
trying
to access xmethods for adding web service, it can't access as the internet
connection
is thru proxy.
Can anybody pls tell me how to configure the internet proxy with this
portlet
builder ?
TIA,
Sudarson -
How to Configure Oracle Management Server (OMS) with Dataguard Broker
Dear Experts,
i have a production DB (192.168.200.9) 9.2.0.1.0 on Server 2003
i have a standby DB (192.168.200.19) 9.2.0.1.0 on Server 2003
Archive logs are shipped to standby database and applied there. *(Datagauard is configured).*
Now i want that Graphically i want to see that archivelogs are shipping to standby database and applied there ( i want to configure Dataguard Broker in graphical mode (*dataguard manager*) isnt it ( bcz i anm bit confused with this).............?
*1.* For this purpose to achieve i take some seperate machine install on it Server 2003.
*2.* and then Install oracle db 9.2.0.1.0 ( here i will install FULL DATABASE, CUSTOM installation ( then createsome repository).
*3*. can i configure this repository for OMS on my already running production or standby DB............?
*4.* After this OMS is configured or not..........?
*5.* how i will configure datagauard broker
what i know regarding this is on primary and standby db *( DG_BROKER_START = TRUE)* and after
this we have to create some configuration wizards but how
i think i have to go with this sequence if somebody has different sequence tellm e
wait for replies
thanks in advance
regards rehan
faisalabad pakistanDoes anybody dont know anything about this.................?
-
How to configure BODS in network environment with NAT ?
Hi Team,
Now we are working on POC of BO Data Services 4.0 with SI partner and they reported us that a communication error (error code:BODI-1241023) occurred when they started a job from Designer.
They can do it without any problems in the following two cases.
1. from Designer which is installed in the CMS/JobServer machine
2. from Designer which is installed in local PC within internal network (without firewall / NAT)
That is, the cause is Firewall with NAT(Network Address Translation) between Designer and JobServer/CMS.
And, they can log on to CMS/JobServer with NAT environment, however, cann't start a job from Designer.
The port #3500 for JobServer is open. They confirmed that they could log on to the JobServer in the event log
of the JobServer.
That is, Designer -> CMS/JobServer communication is OK, but JobServer -> Designer communication must be NG.
Could you advise us how to configure BODS both client and server sides in the network environment with NAT ?
Thanks and best regards,HI Buddy,
You can achieve this by $FLEX$, create first value set, and assign it to first field. Create second value set based on first value set using $FLEX$.
follow steps mentioned in the bellow link
http://erpschools.com/articles/usage-of-flex -
How to configure SMTP server in OSB eclipse platform
how to configure the SMTP server in OSB eclipse platform......
secondly.................the output email shud contain message sent and not the overview of the mail how do i do itHow to configure the server? That depends on what server it is. If you are the administrator I would suggest finding the help file for the server and searching for the term "relaying". However I hope you are not, and can ask the real administrator.
-
How to configure global proxy under ios 7
I would like to know how to configure the global proxy so that I don't need to set for every wifi every time under iphone 5 ios7. It seems the function is not available under ios 7 right now? please help.
Page 27:
https://developer.apple.com/library/ios/featuredarticles/iPhoneConfigurationProf ileRef/iPhoneConfigurationProfileRef.pdf -
How to configure MySQL to be used with J2EE 1.3.1 -- Very Very URGENT.
Hi All,
I have downloaded Sun's J2EE reference implementation 1.3.1. I want to use MySQL as my database instead of the default database Cloudscape that comes with J2EE SDK 1.3.1. Can any one help me configuring in doing the same.
Thanks and regards,
Venky.Hi! I had the same problem, too. I�m Brazilian and I�ve been learning the English language yet, but I�ll try to describe how to configure J2EE with MySQL.
I am using MySQL version 4.1.7 with J2EE version 1.3 on Windows XP Professional. The driver version of MySQL is 3.0.16.
You have to configure the following two files:
- <J2EE_HOME>\bin\setenv.bat
- <J2EE_HOME>\config\resource.properties
Do the following steps:
1) Copy the JAR file of MySQL driver (mysql-connector-java-3.0.16-ga-bin.jar) to <J2EE_HOME>\lib directory.
2) In <J2EE_HOME>\bin directory open the setenv.bat file and analize the code. It is not hard to understand the code, it is just the classpath configuration of J2EE. After understand it, add a reference of MySQL driver (mysql-connector-java-3.0.16-ga-bin.jar), that was copied to <J2EE_HOME>\lib directory.
3) Run the <J2EE_HOME>\bin\j2eeadmin.bat to configure the resource.properties file.There are two command lines to be executed, as below:
- j2eeadmin.bat -addJdbcDriver <CLASS NAME OF THE DRIVER>
- j2eeadmin.bat -addJdbcDatasource <JNDI NAME> <URL>
For example:
- j2eeadmin.bat -addJdbcDriver "com.mysql.jdbc.Driver"
- j2eeadmin.bat -addJdbcDatasource "jdbc/mysql/test" "jdbc:mysql://localhost/test?user=username&password=pass"
4) After run j2eeadmin.bat, the resource.properties file will be modified. But when I did it and when I executed the verbose command to start J2EE, some error messages was exhibited. So I decided to open the resource.properties file and I noticed that the character "\" was added erroneously in a lot of places of the code. It did not seem correct, so I decided to remove these characters replacing them. Bingo!!! After I did it, I run verbose again and no more message error ocurred. I think it is a bug of J2EE.
Finish! I modified the datasource JNDI to access MySQL and then I run my EAR application. No problems occurred. My application is running succesfully.
Good luck! -
How to configure airport extreme to work with Actiontec gt701d modem
I have been trying to set up a new Actiontec modem to work with a new Airport Extreme with no luck. I don't know what the right settings are to get it to work correctly. So far the only way I have been able to get the two to work together is to have the AE connect with ethernet and bridge mode. However with this configuration I can't setup a guest network which I would like to be able to do. I have read some past posts and have tried other configurations but end up either losing internet connection or getting a very slow connection. If anyone has some idea how to get this modem to work with the AE i would really appreciate some advice
Thank youWelcome to the discussion area, Meagan!
The Actiontec "modem" that you mention is really a gateway...a combination modem/router, so with this device and the AirPort Extreme, you have two routers on the network.
Whenever you have two routers on a network, the first router must be configured to handle the main routing chores and any other routers must be configured in Bridge Mode to function correctly. So, Bridge Mode is the correct setting for the AirPort Extreme when used with the Actiontec gt701d gateway.
In order for the AirPort Extreme to provide a Guest Network, it must be configured as the "main" router on a network. This won't be possible unless you can re-configure the Actiontec device to act as a simple modem, not a router. You might want to check with Actiontec support to see whether this might be possible.
Message was edited by: Bob Timmons -
How to configure ACS to authenticate Modem with radius
Hi,
How do I configure ACS to authenticate and authorize modem users with radius. My problem is with authorization(authentication is ok in the debug). Do I need to configure specific Av pairs (006 and 007 in IETF)Hi Dominic,
Are we have Microsoft radius server or ACS?
Yes, these attributes should be configured.
006-service-type: login
007-framed-protocol: PPP
HTH
JK -
How to configure Oracle 8 to work with Weblogic portal4.0
Hi! I'm trying to configure my portal to work with oracle8i using thin driver.I've set classes12.zip in the classpath.But if I set the DATABASE=ORACLE_OCI value inthe set-environment.sh file the server does not start.Pls help.
Here's the error log it throws for the problem:
: 'Fatal initialization exception
Throwable: java.lang.IllegalAccessError: Exception[com.bea.p13n.security.realm.R
DBMSException: An error occured creating a database connection for the realm.]
java.lang.IllegalAccessError: Exception[com.bea.p13n.security.realm.RDBMSExcepti
on: An error occured creating a database connection for the realm.]
at weblogic.security.acl.Realm.getRealm(Realm.java:91)
at weblogic.security.acl.Realm.getRealm(Realm.java:62)
at weblogic.security.SecurityService.initializeRealm(SecurityService.jav
a:258)
at weblogic.security.SecurityService.initialize(SecurityService.java:115
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:390)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:202)
at weblogic.Server.main(Server.java:35)
'> -
How to configure dbconsole on R12.1 with 11g database on RHEL AS 5(64-bit)
Hi Dear
I want to configure dbcosnole on R12.1 with 11g database. When i start it by executing the command emctl start dbconsole it does not start. It shows the following error:
OC4J Configuration issue. /u01/oracle/PROD/db/tech_st/11.1.0/oc4j/j2ee/OC4J_DBConsole_dg.orientpower.com.pk_PROD not found.
I will highly appreciate, if anybody could help me to resolve this issue.
Thnx
JabbarYou might want to checkout
http://download.oracle.com/docs/cd/E11882_01/install.112/e10813/dbcacrea.htm#sthref287
Oracle® Real Application Clusters Installation Guide
11g Release 2 (11.2) for Linux and UNIX
Maybe you are looking for
-
I'm still a newbie at this, so pleasse bear with me. I have a links page on a website for myself. I wish to create a link from a hidden button over the text to a pdf file within the project folder. I keep getting errors saying that it cant find the f
-
Error "INCLUDE report "/1CAGTF/IF_LOGFUNC_000208" not found" in SolMan.
Hi experts, Need help, in SolMan when EWA background job executes it gives error: Short text Syntax error in program "RDSVASAEW_DBMSS____________061 ". What happened? Error in the ABAP Application Program The current ABAP program "SAPL
-
Switch access for an iPod touch
I'm trying to figure out how to use a switch with an iPod touch. One of my students is motivated by listening to the iPod touch. I would like to use this motivation to work on her accessing her environment by using a switch/device. Is there any way t
-
I have had photoshop elements 6 for years and use it regularly. It disappeared in front of me 2 days ago, Now what do i do? I have the original cd, and have tried to upload it again, but to no avail...... Now what? SINCERELY Nicole Ramirez
-
How are you able to publish a website on iWeb without using a .Mac account? G4 Processor Dual 867 MHz Mac OS X (10.4.6) 4GB iPod Mini - If I answered your question, I'd love it if you marked so