How to configure isdn pri on gigabit interface on AS 5850 router

hello All,
i currently have a project at hand which is a voip project using sip protocol. my client wants to send voip traffic to my router using STM interface with SIP protocol. But the challenge is how do i convert the sip protocol to ISDN PRI on another STM gigabit interface before sending it to my PSTN switch for onward termination to the customer. currently i use serial interface to communicate with my PSTN using E1 for other existing clients in other to terminate calls to customers. please see sample configuration below:
interface Serial10/1:15
no ip address
encapsulation hdlc
no snmp trap link-status
trunk-group JKN
isdn switch-type primary-net5
isdn incoming-voice modem 64
isdn map address .* plan unknown type unknown
isdn send-alerting
no cdp enable
thank you.
Adekunle

hello n-kirillov,
Yes i mean STM as Synchronous Transport Module for Optical Network. currently, the medium of transport for communication between my router and the PSTN switch is the serial interface whose configuration i have shown above. also currently E1 pri cables are connected to this serial interface and E1s are provision for this serial interfaces directly from the switch for communication with the PSTN switch.
the question now is that my switching team now wants be to communicate with their switch using fibre from STM interface on my router without using PRI cables. is this achievable? if yes what is the configuration like?

Similar Messages

How to configure Multiple PPTP VPN Clients on cisco 3g supported Router

I want the router to be a PPTP VPN client to 2 independent PPTP servers, both are in different cities in Cisco routers. I have tested with one on cisco 1841 aqnd its working fine; but when I add the 2nd, its using vpdn-group 1 and therefore connecting to the wrong PPTP server:
here is the config for the one that works:
vpdn-group 1
request-dialin
protocol pptp
rotary-group 0
initiate-to ip xxx.xxx.xxx.xxx
interface Dialer0
mtu 1450
ip address negotiated
ip pim dense-mode
ip nat outside
ip virtual-reassembly
zone-member security private
encapsulation ppp
ip igmp query-interval 125
dialer in-band
dialer idle-timeout 0
dialer string 123
dialer vpdn
dialer-group 1
no peer neighbor-route
no cdp enable
ppp pfc local request
ppp pfc remote apply
ppp encrypt mppe auto
ppp authentication ms-chap-v2 ms-chap eap chap pap callin
ppp eap refuse
ppp chap hostname xxx@xxx
ppp chap password 7 xxxpassword
But if I create a vpdn-group 2 and a Dialer1 interface, with dialer-group 2, its still attempting to connect to the IP in vpdn-group 1 - how do I get it to use the 2nd vpdn-group, or how do I make this work? and which cisco 3G Router you prefer because these are remote sites and only 3G Internet service is available.

I want the router to be a PPTP VPN client to 2 independent PPTP servers, both are in different cities in Cisco routers. I have tested with one on cisco 1841 aqnd its working fine; but when I add the 2nd, its using vpdn-group 1 and therefore connecting to the wrong PPTP server:
here is the config for the one that works:
vpdn-group 1
request-dialin
protocol pptp
rotary-group 0
initiate-to ip xxx.xxx.xxx.xxx
interface Dialer0
mtu 1450
ip address negotiated
ip pim dense-mode
ip nat outside
ip virtual-reassembly
zone-member security private
encapsulation ppp
ip igmp query-interval 125
dialer in-band
dialer idle-timeout 0
dialer string 123
dialer vpdn
dialer-group 1
no peer neighbor-route
no cdp enable
ppp pfc local request
ppp pfc remote apply
ppp encrypt mppe auto
ppp authentication ms-chap-v2 ms-chap eap chap pap callin
ppp eap refuse
ppp chap hostname xxx@xxx
ppp chap password 7 xxxpassword
But if I create a vpdn-group 2 and a Dialer1 interface, with dialer-group 2, its still attempting to connect to the IP in vpdn-group 1 - how do I get it to use the 2nd vpdn-group, or how do I make this work? and which cisco 3G Router you prefer because these are remote sites and only 3G Internet service is available.

How to Configure Transparent caching on Cat 6500 with CSM in routed mode

I am trying to configure Transparent caching on Cat 6500 with CSM in routed mode, but facing some problems in it , also I have gone thru the example config on cisco site for transparent caching using CSM on Cat 6500 , but the above does not fit my clients requirement.
The scenario is like
Access Switches - Cat6500 with MSFC & CSM - Internet Router
|
Cache Engines and Real servers
The clients as well as real servers are on seperate VLANs (L3) and the requirement is to load balance the internet traffic using cache engines.
I'd really appreciate any helpful suggestions or any useful links/docs/info on this.
Thanks
kumar

Hello Joerg,
Thanks for the reply.
I have already gone thru the sample config shown by this weblink, however this link refers to configuring transparent caching on the CSM in BRIDGED MODE ( i.e both the client and server vlans are having the same IP address ) but in our case , we have multiple L3 VLANS on the CAT6509 having IP addresses in different SUBNETS , and the Real servers to be used for caching also exist on one of these VLANS. Thus, the scenario described by the Weblink does not apply here. Also , in the configuration referred by the above weblink, the VLAN 100 is configured as client , however the endusers are shown to be on vlan200 which is configured as SERVER VLAN in the CSM.
Dont you think there is something wrong here, I mean the endusers should be on VLAN 100 (Client) and real servers on VLAN 200 (SERVER).
So, I have to configure CSM in routed mode ( i.e both the client and server vlans will have seperate IP addresses in different subnets ) and the endusers will be on all VLANS .
Pls let me know , how I can implement this solution.
Thanks again
Sudhir

How to Configure Multiple Portal Middle Tiers with a Load Balancing Router

Hi,
Portal version trying to install 10.1.2 on Windows 2003 boxes.
I am following the guide http://download.oracle.com/docs/cd/B14099_19/portal.1012/b14037/cg_advnc.htm#i1046354. I have InfraStructure installed on a different box and am trying to install 2 Portal Midtiers each on separate boxes and using LBR. The above document is kind of confusing as I am trying to following
5.3.1 Step 1: Install a Single Portal and Wireless Middle Tier (M1)
5.3.2 Step 2: Configure OracleAS Portal on M1 to Be Accessed Through the LBR (AND FOLLOW ARE THE STEPS 1 to 14 in sequence)
if I follow 1 to 14 steps in sequence the information is not consistent what is being listed in the following sections
5.4.1 Create Virtual Hosts
5.4.2 Configure OracleAS Web Cache
5.4.3 Register OracleAS Portal with OracleAS Single Sign-On
i.e.
ptlconfig -dad portal -sso -host www.abc.com -port 7779
ptlconfig -dad portal -sso -host www.xyz.com -port 7779
as in the above steps it says to run
ptlconfig -dad portal -wc -site
and ssoreg command that always fails because I am running it from midtier as it gives error saying invalid username/password
as oppoesed to steps listed in point 8, 9, 10, 11 and 12.
Can someone please privide the steps in sequence I need to follow when installing 2 midtiers with frontend LBR and one infrastructure. I am trying to follow the architecture listed in the above link.
Any help is really appreciated.
Thanks

Hi,
Will appreciate any inputs on the following.
I am planning to install Infrastructure and one Midtier BI Forms Reports Discoverer, Portal on one windows box and the second midtier BI Forms Discoverer, Portal on the second windows box.
Please correct me if I am wrong on installing and configuring the mid-tiers as following are the steps I have compiled going through the document and want to make sure this time I do it right.
As I'll be installing BI Forms Reports Discoverer, Portal so wondering when I install the second midtier do I need to unselect all Portal, Forms, Reports, Discoverer or just the Portal I need to unselect.
Also in the host file of both the windows boxes do I just need to keep the LBR IP Address entry and remove the rest.
LBR:_
Computer Name: bigip5.prd.com
IP Address: *167.123.2.5*
Listen Port: *80*
Invaidation Port: *9401*
Infrastructure:_
Computer Name: portal1.prd.com
IP Address: *167.123.2.6*
Oracle HTTP Server Listening Port: *7777*
Application Server Control port: *1800*
M1 (Portal & BI Forms Reports Discoverer):_
Computer Name: portal1.prd.com
IP Address: *167.123.2.6*
Oracle HTTP Server Listening Port: *7778*
OracleAS Web Cache Listening Port: *80*
OracleAS Web Cache Invalidation Port: *9401*
OracleAS Web Cache Administration Port: *9400*
Web Cache Statistics port: *9402*
Application Server Control port: *1810*
M2 (Portal & BI Forms Reports Discoverer):_
Computer Name: portal2.prd.com
IP Address: *167.123.2.7*
Oracle HTTP Server Listening Port: *7778*
OracleAS Web Cache Listening Port: *80*
OracleAS Web Cache Invalidation Port: *9401*
OracleAS Web Cache Administration Port: *9400*
Web Cache Statistics port: *9402*
Application Server Control port: *1810*
First to create MetadataRepository and then Install Infrastructure and then follow the below steps to install Midtiers
Install and Configure of M1 (Portal and BI Forms Reports Discoverer):-_
*5.3.1 Step 1*: Install a Single Portal and BI Forms Reports Discoverer (M1 i.e. portal1.prd.com)
*5.3.2 Step 2*: Configure OracleAS Portal and BI Forms Reports Discoverer on M1 to Be Accessed Through the LBR
*1.* Configure LBR
*2.* Follow Section 5.4.1.1 to create the Virtual Host for bigip5.prd.com (LBR) and portal1.prd.com (M1)
*3.* Define a site that matches the virtual host entry for bigip5.prd.com (LBR) on Webcache of M1
*4.* Use OracleAS Web Cache Manager on M1, to map the site bigip5.prd.com (LBR) to middle tier portal1.prd.com (M1).
Follow steps 5 and 6 as per the document
*7.* Configure bigip5.prd.com (LBR) to accept invalidation requests from the OracleAS Metadata Repository on a separate port i.e. 9401
*8.* Change iasconfig.xml on M1
*9.* run ptlconfig -encrypt
*10.* Register the URL changes with OracleAS Portal by running ptlconfig -dad portal -wc -site
*11.* No need as it is http only
*12.* Run the follwoing
MID_TIER_ORACLE_HOME_M1\sso\bin\ssoreg.bat
-site_name bigip5.prd.com
-mod_osso_url http://bigip5.prd.com:80
-config_mod_osso TRUE
-oracle_home_path MID_TIER_ORACLE_HOME_M1
-config_file MID_TIER_ORACLE_HOME_M1\Apache\Apache\conf\osso\osso.conf
-admin_info cn=orcladmin
-virtualhost
*13.* Edit targets.xml to enable monitoring of the LBR's front-end host and port settings for OracleAS Portal
+<Property NAME="PortalListeningHostPort" VALUE=http://bigip5.prd.com:80/>+ and then run
MID_TIER_ORACLE_HOME_M1\bin\emctl reload
*14.* Test the setup
Install and Configure of M2 (Portal and BI Forms Reports Discoverer):-_
*5.3.4 Step 4*: Install a Single Portal and BI Forms Reports Discoverer (M2 i.e. portal2.prd.com)
*1.* As I am installing on wiondows so will not set IASCONFIG_LOC environment variable as I can just copy the iasconfig.xml file from M1 to M2
*2.* Run OUI on M2
*3.* Clear the selection for OracleAS Portal but don't know if I need to unselect Forms , Reports, Discoverer also.
*4.* Enable OracleAS Portal
*5.3.5 Step 5:* Configure the New Middle Tier (M2) to Run Your Existing Portal
*1.* Create both virtual hosts as done on M1
*2.* Copy dads.conf, oradav.conf, cache.conf, web.xml from M1 to M2
*3.* Re-register mod_osso on M2. To do this, perform the following steps by copying osso.conf from M1 to M2
*4.* Synchronize the DCM by using the following command
MID_TIER_ORACLE_HOME_M2/Apache/Apache/bin/ssotransfer MID_TIER_ORACLE_HOME_M2/Apache/Apache/conf/osso/osso.conf
*5.* Run dcmctl updateConfig
*6.* add the necessary mod_rewrite and mod_oc4j directives to the httpd.conf and mod_oc4j.conf files respectively
*7.* Restart Oracle HTTP Server on M2
*8.* Access the OracleAS Web Cache Manager on M1 and follow steps 9,10,11,12,13,14,15,16 for Webcache seetings and clustering.
Also will appreciate if can get some info on the following:
*1.*
When I configure the Webcache as per the Document but if I bring down one Midtier Instance the requests are not going to the other Instance that is up and ignores the case whether an instance is down. Any idea how what and where do I need to provide any setting which in case of instance is down routes the requests to the one that is up.
*2.*
What exactly happens when it says To enable monitoring of the LBR's front-end host and port settings for OracleAS Portal edit target.xml. Is this for LBR to find if an Instance is down or not and route the requests appropriately.
Thanks again for all the help.

ISDN PRI Configuration errors

Dears,
I trying to configure a ISDN PRI on a 1751-V router and the following error occur:
CISCO_BARR(config-controller)#pri-group time 1-6
%Controller tdm clock does not have data capability
%Insufficient HDLC resource for pri-group - it has been removed
How do I to configure ISDN PRI in that router ?
More information:
Cisco 1751-V
Router Version: c1700-ipvoice-mz.123-9d.bin

Hi,
Please make sure that you putting the T1/E1 card in the WVIC and not VIC slot as PRI can do
voice but it is still considedred as data, so if you try to confiugre this in a slot that
is VIC (instead of VWIC) only then it will not work for you. Furthermore, you needed to
have the tdm clock command set to both and not just voice, as you are creating a PRI,
which, again, is Data, but can do voice too.
here is the example of command :--
tdm clock T1 2/0 both export line
hth
CJ

Why do we need to assign ip for the D channel ISDN-PRI

Why do we need to assign ip address to the D channel (signaling ) when we configure ISDN-PRI in the example below :
http://www.cisco.com/univercd/cc/td/doc/product/access/ap/ap_ts3/ap_ts3sw/apswisd.htm
<quote>
Step 1:Specify the D channel of the first Primary Rate Interface (PRI):
AS01(config)# interface Serial 0:23
AS01(config-if)#
Step 2: Assign an IP address and subnet mask to the interface:
AS01(config-if)# ip address 172.16.254.253
</quote>
Regards

You can assing one there, and / or on dialer interfaces. It depends on what you are doing.
These will be the address used by PPP when it runs on the B-channels.

ISDN PRI & BRI configration

Hi,
I have 2800 series route at central location with PRI line and remote location with BRI line and DLINK router. i have 10 remote site.
Now i want to connect my multiple remote site through BRI to my PRI at central location
can you guide me with the configration at the central location PRI part
I am in INDIA
Bhargav

in india we have E1 as a PRI follow the procedure.
Configuring Channelized E1 ISDN PRI
To configure ISDN PRI on a channelized E1 controller, use the following commands beginning in global configuration mode:
Command Purpose
Step 1
isdn switch-type switch-type
Selects a service provider switch type that accommodates PRI. (Refer to Table 17 for a list of supported switch type keywords.)
Step 2
controller e1 slot/port
or
controller e1 number
Defines the controller location in the Cisco 7200 or Cisco 7500 series router by slot and port number.
Defines the controller location in the Cisco 4000 series or the Cisco AS5200 universal access server by unit number.1
Step 3
framing crc4
Defines the framing characteristics as cyclic redundancy check 4 (CRC4).
Step 4
linecode hdb3
Defines the line code as high-density bipolar 3 (HDB3).
Step 5
pri-group [timeslots range]
Configures ISDN PRI.
.1 Controller numbers range 0 through 2 on the Cisco 4000 series and 1 to 2 on the Cisco AS5200 access server.
If you do not specify the time slots, the specified controller is configured for 30 B channels and 1 D channel. The B channel numbers range 1 to 31; channel 16 is the D channel for E1. Corresponding serial interfaces numbers range 0 to 30. In commands, the D channel is interface serial controller-number:15. For example, interface serial 0:15.
Table 17lists the keywords for the supported service provider switch types to be used in Step 1 above.
Dlink you have to configure simple dial-up connectivity with PRI.
Thanks,
Dharmesh Purohit

How to configure e-mail to forward to outlook 2007

I am looking for help in how to configure my Verizon.msn.com e-mail to forward to outlook 2007. Currently my e-mail is forwarded from Verizon to my msn e-mail address.

Do you make any effort to search for your answers before you post your questions? ERMS is the email response system
The 2nd post on this board - Documentation for Interaction Center (IC) WebClient
There is tons of stuff here to answer your questions as well as show you the configuration. You need a 3rd party CTI solution to do chat that you will read about in the blog.
SAP Notes
759923 Frequently Asked Questions about IC WebClient
940882 Frequently Asked Questions about ERMS
882653 Frequently Asked Questions about Agent Inbox
1114557 SAP CRM 2007 Internet Browser Releases
1118231 Supported user interfaces for SAP CRM
981710 Support for Microsoft Internet Explorer 7.0
1144511 Blank screen when starting CRM WebClient or IC WebClient
1115493 CRM Web UI: Mandatory SICF services for CRM framework
992848 Mandatory ICF nodes for CRM WebClient UI Framework
IC WebClient Consultant Cookbook for CRM 2005
Online Documentation
Online Knowledge Products
Blog: How to Configure Contact Center Simulator User Interface (CCSUI)
Blog: What is Computer Telephony Integration (CTI)

How to Configure E-mail and Chat functionalities

Dear all,
How to configure E-mail and Chat functionalities for IC Webclient.
through IC Webclient ICI interface how can we configure E-mail functionality, As per my understanding, E-mails can be handled in a similar way of receiving phones.
Where these E-mails can be stored?, Where we define agent E-mail id?
being ICI is a multi channel support does it need SMPT server support? If No, would there be any difference in the functionality?
How does CHAT functionality works?
Please educate in above scenarios to get a better understanding.
Your help will be highly appreciated.
Best wishes
Raghu ram

Do you make any effort to search for your answers before you post your questions? ERMS is the email response system
The 2nd post on this board - Documentation for Interaction Center (IC) WebClient
There is tons of stuff here to answer your questions as well as show you the configuration. You need a 3rd party CTI solution to do chat that you will read about in the blog.
SAP Notes
759923 Frequently Asked Questions about IC WebClient
940882 Frequently Asked Questions about ERMS
882653 Frequently Asked Questions about Agent Inbox
1114557 SAP CRM 2007 Internet Browser Releases
1118231 Supported user interfaces for SAP CRM
981710 Support for Microsoft Internet Explorer 7.0
1144511 Blank screen when starting CRM WebClient or IC WebClient
1115493 CRM Web UI: Mandatory SICF services for CRM framework
992848 Mandatory ICF nodes for CRM WebClient UI Framework
IC WebClient Consultant Cookbook for CRM 2005
Online Documentation
Online Knowledge Products
Blog: How to Configure Contact Center Simulator User Interface (CCSUI)
Blog: What is Computer Telephony Integration (CTI)

How to Configure Transparent caching on Cat 6500 with CSM in bridge mode?

hi.
I found How to Configure Transparent caching on Cat 6500 with CSM in routed mode.
But,
I need help How to Configure Transparent caching on Cat 6500 with CSM in bridge mode?
Please let me know sample configuration.
thanks.

Hi,
I wrote the document you mentioned and I also wrote the one below.
http://www.cisco.com/en/US/partner/products/hw/modules/ps2706/products_configuration_example09186a00802c1201.shtml
The one with the SSLM is a bridge mode config.
If you replace the SSLM with a cache [or a farm of caches] it would be a similar config.
Replace the SSL21 vserver with an HTTP vserver [most important is to keep the vlan configured on each vserver]
Regards,
Gilles.

How to fake ISDN b-channels as busy out of the pri-group timeslots definition ?

Hi, Cisco Support Community,
This is my first post here, so I hope I won't make mistakes... First, thanks for reading me.
I wanted to reuse an old 2811 to act as a SIP gateway on an ISDN primary rate interface. This router is featured with 2 PVDM2-8 modules, so that we're able to handle up to 16 simultaneous calls. So I ordered a pri with 10 channels, which is supposed to be more than enough for our usage.
Everything works fine, excepted that I discovered that the PRI which was delivered to us is a full one, meaning 30 B channels.
As a result, as incoming calls are dispatched round robin by the isdn line provider, when incoming calls start to be presented on b-channel 16, the call is rejected by the router with a "channel unavailable" message... The only way to have a successful incoming call is then to have 15 more unsuccessful tries so that the calls are presented on B-channel 1 again :-/
I have to wait for monday to deal with the line provider to sort this out, but meanwhile, I was trying to find a workaround.
My first try was to use B-channel negotiation on the serial interface (isdn negotiate-bchan resend-setup), but it seems that b channel negociation is disabled on the provider side.
So the other obvious solution would be to fake channels 17 to 31 as busy (isdn busy b_channel xx) ... But as the pri-group timeslots are 1-16, the related serial interface is serial0/0/0:15, and I'm unable to set busy B-channels over 15. And of course, I have no way to define pri-group timeslots 1-31 as I have not enough DSPs to handle more than 16.
I also tried to use the ds0 busyout directive within the E1 controller configuration, but while the command is accepted, it does not appear in the configuration
Below is my running configuration... If some of you can help, this would be much appreciated. Current IOS on the router is Version 12.3(11)T3
Kind regards,
Philippe Martorell
--- cut here ---
Current configuration : 4311 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname RTR-xyz-abc
boot-start-marker
boot-end-marker
enable secret 5 xx
username user1 privilege 15 secret 5 xx
username user3 privilege 15 secret 5 xx
username user1 privilege 15 secret 5 xx
network-clock-participate wic 0
network-clock-select 1 E1 0/0/0
aaa new-model
aaa authentication login default local
aaa session-id common
ip subnet-zero
ip cef
ip name-server 8.8.8.8
ip name-server 8.8.4.4
no ftp-server write-enable
isdn switch-type primary-net5
voice-card 0
dspfarm
no local-bypass
voice call send-alert
voice call carrier capacity active
voice rtp send-recv
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
sip
no call service stop
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
controller E1 0/0/0
pri-group timeslots 1-16
translation-rule 1
Rule 1 ..% 900 international international
Rule 2 ..% 90 national national
translation-rule 2
Rule 1 ..% 02212345
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0/0$
ip address 172.16.31.200 255.255.255.0
duplex auto
speed auto
no mop enabled
interface FastEthernet0/1
ip address 10.0.1.200 255.255.255.0
shutdown
duplex auto
speed auto
interface Serial0/0/0:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice voice
isdn map address .* plan unknown type unknown
isdn negotiate-bchan resend-setup
isdn outgoing-voice info-transfer-capability 3.1kHz-audio
no cdp enable
ip default-gateway 172.16.31.254
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.31.254
no ip http server
snmp-server community xx RO
control-plane
voice-port 0/0/0:15
no echo-cancel enable
playout-delay maximum 170
playout-delay nominal 80
playout-delay minimum low
cptone CH
bearer-cap 3100Hz
no mgcp piggyback message
dial-peer voice 1 pots
application session
incoming called-number .
direct-inward-dial
dial-peer voice 456389160 voip
destination-pattern 6[0-8]
translate-outgoing calling 1
translate-outgoing called 2
rtp payload-type cisco-codec-fax-ind 124
rtp payload-type nte 96
no modem passthrough
voice-class codec 1
session protocol sipv2
session target ipv4:10.200.3.21
dtmf-relay rtp-nte
fax rate disable
no vad
dial-peer voice 999999 voip
answer-address 0.
rtp payload-type cisco-codec-fax-ind 124
rtp payload-type nte 96
no modem passthrough
voice-class codec 1
session protocol sipv2
dtmf-relay rtp-nte
fax rate disable
fax protocol pass-through g711ulaw
no vad
dial-peer voice 9912 pots
destination-pattern 99123T
progress_ind alert enable 8
port 0/0/0:15
dial-peer voice 9920 pots
destination-pattern 99222T
clid restrict
clid restrict
port 0/0/0:15
dial-peer voice 456389162 voip
destination-pattern 69
translate-outgoing calling 1
translate-outgoing called 2
rtp payload-type cisco-codec-fax-ind 124
rtp payload-type nte 96
modem passthrough nse codec g711ulaw
voice-class codec 1
session protocol sipv2
session target ipv4:10.200.3.21
dtmf-relay h245-alphanumeric
fax-relay ecm disable
fax rate 9600
fax nsf 000000
fax protocol t38 ls-redundancy 2 hs-redundancy 2 fallback none
no vad
gateway
timer receive-rtp 1200
sip-ua
max-forwards 15
sip-server ipv4:10.200.3.21
banner login ^CCC
WARNING: This is a private network.
Unauthorized access is prohibited.
Use of this system constitutes your
consent to interception, monitoring,
and recording for official purposes
of information related to such use,
including criminal investigations.
^C
line con 0
line aux 0
line vty 0 4
password 7 xx
scheduler allocate 20000 1000
end

Hi,
Thanks for your answer, but unfortunately, this did not help. commands ds0 busyout are accepted, but not taken into account :
RTR-505-012#conf t
*Apr 7 10:23:04.361: %SYS-5-CONFIG_I: Configured from console by sysadmin9 on vty0 (172.16.0.88)
Enter configuration commands, one per line. End with CNTL/Z.
RTR-505-012(config)#controller e1 0/0/0
RTR-505-012(config-controller)#ds0 busyout 17-31
RTR-505-012(config-controller)#do sh run | begin controller
controller E1 0/0/0
pri-group timeslots 1-16
And the "isdn service b_channel state" commands in the serial interface context are rejected
RTR-505-012(config-controller)#interface Serial0/0/0:15
RTR-505-012(config-if)#isdn service b_channel 16 state 2
%The service state of reserved channel 16 on DSL 0 can not be changed.
While the "show isdn service" status shows channels 16 to 30 are out of service, some incoming calls are still directed to these channels by the provider :
RTR-505-012#show isdn service
PRI Channel Statistics:
ISDN Se0/0/0:15, Channel [1-31]
Configured Isdn Interface (dsl) 0
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
*Apr 7 10:20:45.509: %ISDN-6-CHAN_UNAVAILABLE: Interface Se0/0/0:15 Requested Channel 19 is not available
*Apr 7 10:20:53.353: %ISDN-6-CHAN_UNAVAILABLE: Interface Se0/0/0:15 Requested Channel 20 is not available
I'll try to sort this out with the provider today.
Thanks,
Philippe.

How to configure the web interface of service desk

Hi All,
We are currently doing a configuration on solman service desk. I am on a stage where in i need to use the web interface of service desk via tcode notif_create_bsp. However, every time i call the transaction code (call the url) i cant view the web. Only an error the "Network Access Message: The website cannot be found".
I already activate needed services and already publish
SIAC_PUBLISH_ALL_INT but it still doesnt work.
I might have missed some configs/procedure on how to do it correctly.
My questions are.
1. How am i going to know the qualified domain name
of the Web AS for solman? How to configure it?
2. Can anyone give me some guide and any step by step documentation/procedure on this.
You help/suggestion will be very much appreciated
Thank you very much,
Ice

Hi,
+"Check the following 2 things. See if the port 8000 is open and in the url for the BSP in internet explorer, replace the host name with the IP address of your Solman server.+
+"+
That was a helpful tip. I change the host name with the ip address ofour solman server. However, upon login, it promts me to enter username and password. I've tried to login using my solman password but it shows an error like this.
Business Server Page (BSP) error
What happened?
Calling the BSP page was terminated due to an error.
SAP Note
The following error text was processed in the system:
Die URL enthält keine vollständige Domainangabe (10.123.161.125 statt 10.123.161.125.).
Exception Class CX_FQDN
Error Name
Program CX_FQDN=======================CP
Include CX_FQDN=======================CM002
ABAP Class CX_FQDN
Method CHECK
Line 10
Long text -
Error type: Exception
Your SAP Business Server Pages Team
Is there anything i need to configure so that i can maintan the username and password?
Thank you for your assistance,
Ice

How to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

how to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

Hi ,
Have you got any additional public IP Address from your service provider , If yes on router you can have static route for those additional IP Address pointing to your ASA outside interface .
Accordingly you can configure NAT
HTH
Sandy .

How to configure network interface only when cable inserted?

Hi there,
I was wondering if anyone here could help me with a minor configuration problem. I have a server with two network interfaces, I'll call one "internal" and the other one "external". It has NAT configured so that the "internal" interface gets served DHCP, can access the Internet, etc. My problem is that sometimes I want to run the server without anything connected to the internal interface, and at these times it seems that the boot process gets stuck on the "bringing up internal interface" part. (It's a bit hard to know exactly what's going on because the server is headless.) I am using a script in /etc/network.d/, set to static IP address, for the internal interface.
Does anyone know how I could configure Arch so that it only tries to bring up the internal interface if something is actually connected to the port? Otherwise I have to physically go to my server and plug in my laptop to keep the boot process going... let me know if I should provide more details.
Thanks for your suggestions!

ifplugd? Which is used by net-auto-wired from netcfg.

How to configure snmp on loopback interface, on vrf TEST, in ASR 9000 series

Hi there!
How to configure snmp v2, with community string, for ASR 9000 series, in interface loopback 1, that has vrf TEST
Regards!

oh that is somewhat vague, but let me try...
in order to enable snmp access to an interface in a vrf you need to enable MPP (management plane protection) in that vrf.
Something like this:
control-plane
management-plane
inband
interface Loopback100
allow all
if you have this and it doesn't work, a config snippet and some debugs (like debug snmp packet) will help to define what to do next.
regards
xander

How to configure isdn pri on gigabit interface on AS 5850 router

Similar Messages

Maybe you are looking for