How to fix my router that I messed up.

I was attempting to connect my router to the internet. I ran an ethernet cord from Dell PowerConnect 2016, which is connected to my desktop, to my Cisco Linksys E1000 router and I plugged it into the ethernet port instead of the internet port and it has messed everything up. How do I fix this in order to be able to use my wireless router? Before I did this I was able to wirelessly connect my laptop to the router, but as soon as I plugged the ethernet cord into the wrong port on the router everything messed up.

Before you continue below, make sure you've first tried a hard reset to revive your router as previously suggested. If that fails, try the following:
Disconnect the router from UTP cables (not the power cable).
Push reset button for 30 secs.
Without releasing reset button, disconnect power cord.
Hold the reset button for another 30 secs.
Replug the power cord.
Still hold the reset button for another 30 secs.
Release the reset button and give the router about 10 secs to resettle.
Disconnect power cord for another 10 secs and then reconnect.
All should be in default settings now.
This procedure is usually called 30/30/30 reset.
If you still have issues, try first connecting a single computer to the router DIRECTLY using a UTP cable. Try logging in via the web interface. Tell us what happens.

Similar Messages

How to fix iframe issue that displays XML values instead of formatted XML in IE11

The following sub.jsp file shows the formatted XML properly as expected when is opened directly:
<% response.setContentType("text/xml"); %>
<book>
<chapter1>chapter 1</chapter1>
<chapter2>chapter 2</chapter2>
</book>
IE11 shows the result as below which are colored and can be collapsed or un-collapsed:
<book><chapter1>chapter 1</chapter1><chapter2>chapter 2</chapter2></book>
But if the sub.jsp is opened in an iframe from the below main.html, it only shows the values of the XML in the iframe:
<!DOCTYPE html>
<html>
<head>
<meta charset="ISO-8859-1">
<meta http-equiv="Content-Type" content="text/html; charset=ISO-8859-1">
<title>Insert title here</title>
</head>
<body>
<iframe src="sub.jsp"></iframe>
</body>
</html>
The iframe shows only the XML values, i.e., chapter 1 chapter 2 in IE11. This issue does not happen in IE8.
I appreciate to your if you know how to address this issue.
Regards, Amir

The following sub.jsp file shows the formatted XML properly as expected when is opened directly:
<% response.setContentType("text/xml"); %>
<book>
<chapter1>chapter 1</chapter1>
<chapter2>chapter 2</chapter2>
</book>
IE11 shows the result as below which are colored and can be collapsed or un-collapsed:
<book><chapter1>chapter 1</chapter1><chapter2>chapter 2</chapter2></book>
But if the sub.jsp is opened in an iframe from the below main.html, it only shows the values of the XML in the iframe:
<!DOCTYPE html>
<html>
<head>
<meta charset="ISO-8859-1">
<meta http-equiv="Content-Type" content="text/html; charset=ISO-8859-1">
<title>Insert title here</title>
</head>
<body>
<iframe src="sub.jsp"></iframe>
</body>
</html>
The iframe shows only the XML values, i.e., chapter 1 chapter 2 in IE11. This issue does not happen in IE8.
I appreciate to your if you know how to address this issue.
This issue is also posted at below link:
https://social.msdn.microsoft.com/Forums/en-US/5b0692b4-d312-4797-9089-42c1029ac059/how-to-fix-iframe-issue-that-displays-xml-values-instead-of-formatted-xml-in-ie11?forum=iewebdevelopment
Regards, Amir

How to fix a shuffle that is stuck on repeat

how to fix a shuffle that is stuck on repeat

Are you sure you have a shuffle? There is no "repeat" setting on a shuffle, unlike other iPods, such as the nano.
The only reason a single song would repeat on a shuffle, is if you have a playlist with only one song, and you have selected that playlist using VoiceOver (or there is only one song on the shuffle).

How to fix a iphone that wont turn on

how to fix a iphone that wont turn on

Connect to Wall Charger for 10 minutes, it may turn ON itself. If still nothing, keep on charger and Reset, hold both home and power buttons for about 20 seconds until iPhone turns ON. If still nothing, clean charging port with toothbrush and small amount of Isopropyl Alcohol.

HT1338 How to fix the safari that crashes under 10.8 ?

Hi, anyone knows how to fix the safari that crashes after upgrading to 10.8 ?
re-installing the system didn't solve it.
thanks

Backup your data and try clean inslall.
Here's reference.

Is there somebody who knows how to fix itunes dj that stop after 4 songs since 10.5 ?

Is there someone who knows how to fix itunes dj that stop after 4 songs since 10,5?
I just have to move the mouse and it starts again.

Hi Tks777,
Thanks for visiting Apple Support Communities.
If you see an "error 4013" when you try to restore your iPhone, try these troubleshooting steps:
Error 4000, 4005, 4013, 4014, and 4016
After you perform each step, try to restore your device.
Restart your computer.
Disconnect all your USB devices from your computer and connect to another USB port.
Use a different USB cable.
Uninstall third-party security software.
Try restoring using an alternate computer.
You can find the article with these steps here:
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
Regards,
Jeremy

How strong is the router that is built into the iMac

How strong is the router that is built into the iMac??
Can you give me a internetadress??
Thanks a lot.

How strong is the router that is built into the iMac??
Router do give some protection, but firewalls provide more security.
For more security, you should look into:
Little Snitch
http://www.obdev.at/products/littlesnitch/index.html
Can you give me a internetadress??
Thanks a lot.
Software routers do not give out internet addresses. A program called DHCP gives out internet address. Your ISP will give your router an internet protocol address. If you have a separate router box, it's DHCP program will dish out another Internet Protocol address to your mac.
RObert

I am a loyal iphone user and of course mine is the 3g iphone.. is that any solution on how to fix the whatsapp that cannot used on all 3g iphone?? i'm not gonna change my phone since i still love my old iphone 3g???

I am a loyal iphone user and of course mine is the 3g iphone.. is that any solution on how to fix the whatsapp that cannot used on all 3g iphone?? i'm not gonna change my phone since i still love my old iphone 3g??? Please reply me. Thanks

There is nothing you can do. The iOS for the iPhone 3G is too old to run WhatsApp

How to fix a router needs to be reset every morning?

I just purchased a new WRT54G V8.0. I upgraded to 8.0.0.2 and set up my network. I have 3 wireless devices and one wired device. The wireless devices are the Desktop, the Laptop, and the Wii console. The wired device is the Xbox.
My problem is this... The network works perfectly all day, no problems what so ever except every morning the router has to be reset and I can't figure out why. Any ideas on how to fix this??
Wireless is set up for DHCP using WAP-PSK with TKIP auth and MAC adress filtering. Everything connects and work fine throughout the day but every morning it needs to be reset.
Thanks.
Message Edited by DaveW on 08-24-2007 08:46 AM

already tried that. the problem is that the router won't assign an IP. Even on the wireless machines, the router shows up as available. I can even connect to it, the problem is it won't assign an IP. I've reset the preferences for the wireless connection, including the WAP key then attempted to recconect. I still couldn't get an IP.
This morning I just reset the router without playing with any settings on the computers. After resetting the router I attempted to reconnect. It asked me to enter the WAP key again, so I did and it connects perfectly.
It's not a huge problem I suppose... but it's really annoying to have to reset the router every morning.

How I fixed my M4 that wouldn't detect in the BIOS

Yeah the power cycling procedure that Crucial posted is **bleep**.
What's happening is that when your SSD thinks the power supply is suspect (which with the current firmware means every time your computer turns off without shutting down) it locks itself to prevent further damage
The procedure that Crucial posted basically has you sit in idle to "convince" your SSD that your power supply is in fact stable by monitoring a period (like 15-20 min) of stable power.
Hard cycling is a common solution but the procedure that Crucial ennumerated only sporatically works.
One thing you guys could so is take a disk tool that can "wake" locked hard drives. I use Parted Magic. Boot into your repair USB or CD with Parted Magic (or whatever utility). As it loads itself it will wake your drive. When you get into the program, simply reboot and your SSD will be good to go.
It's worked every time for me. Alternatively you can struggle with the Crucial procedure, but any means of power cycling will work ie: removing the sata data cable and leaving the SSD plugged into the power for 5-??? minutes. **bleep** even constantly rebooting will eventually get you back in... the point being the Crucial procedure isn't a validated means of doing it more effectively. It's just a bunch of **bleep** that they posted which CAN fix your problem. It's one way. Is it the best way or even a efficacious way? Naw.
For me I wish there was a way to just get my SSD to stop doing this. I initially got a "unstable power supply detected" message a couple weeks ago and now any time I lose power for any reason it locks. IF ANYONE HAS A WAY TO TURN THIS OFF PLEASE POST IT.
Because my computer is a new system that's being fiddled with for overclocking, obviously there are a few system hangs, random boots etc. *keep it courteous* Again if anyone knows how to "untoggle" or reset the protection feature of locking itself, let's hear it

I have an M4 512Gb and I posted here how I fixed it not being recognised 3 times, I think. I did this in a laptop without removing the SSD. I installed it on 7 November and it has been fine for over 2 weeks now. If there are any problems I will report them here. I have 8 partitions on it with about 50% full. The partitions are Linux Ext4. I have lost no data and the system works perfectly now. Disk checks are carried out every 20 boots and they have been fine. I also have a Linux swap partition of about 8Gb which hibernates the computer perfectly. I am wondering if something in the SSD has settled down because I have had no problems since the first day or two. I have been purposely rebooting as often as I can with and without the battery to see if I can make the not being recognised problem reappear. So far it has worked fine. I feel pretty confident at the moment. I do back up my data partition very frequently just to be on the safe side. But I am really pleased with the speed of everything, the fact that I don't worry about bumping the laptop while using it travelling and the nearly doubled battery life. I hope this reassures you.

How to fix audible files that won't sync

Apple repaired my computer. New motherboard and all. Now my iPhone 4s won't sync certain files. iTunes help is horrid and they don't have a phone number. Anyone know how to fix this issue shown below. We're on our own iTunes isn't going to help. And BTW before the repair I had no issues. So now I don't have a clue what to do and I was right in the middle of listening to a book. This isn't the first time iTunes has given me fits either.
I won't dare install and use my new iPhone 5s. Might just return it. What a mess.
Some of the Audible files in the iTunes library were not copied to the iPhone “charlie’s iPhone” because you are not authorized to play them on this computer.
Thanks for any help you can give.

Maybe something in here will help you out:
http://support.apple.com/kb/index?page=search&src=support_site.results.disambigu ation&q=iTunes%20repeatedly%20prompts%20to%20authorize%20computer
ps: you should have made a new post for this question, as the OP is old and irrelevant to your problem.

HT201317 Some photos go to Photo Stream and some go to Camera Roll. How to fix this so that all go to Photo Stream when I take pics?

Sometimes when I take pics on my iPhone 4s the some of the pics go to the Photo Stream while others go to the Camera Roll. Why do they not all go to the camera roll? How to fix this?

Welcome to the Apple Community.
All photos taken on the phone go to the camera roll. If photostream is enabled they should also go to photostream in addition to photos added from other devices. Photos added to photostream from other devices will not be added to the camera roll on your phone (unless you move them manually.
Photos taken on the phone should be added to camera roll immediately, it may take a few moments before they appear in photostream, while they are sent from the camera roll to the cloud and back again to photostream.
If photos aren't being added to photostream there may be a couple of reasons:
Photostream only syncs photos over Wi-Fi, make sure you are connected to Wi-Fi to begin with.
Photostream only syncs when the camera app is closed, ensure it is closed.
Photostream only syncs when the battery is above 20%, try recharging the device
If the problem persists:
Try disabling photo stream on your device (settings > iCloud), restarting your device and then re-enabling photo stream.
If this doesn't help you may need to reset photo stream. You can do this at icloud.com by clicking on your name in the top right corner and then the advanced settings in the pop-up dialogue box that appears.
Note: disabling photostream and re-enabling it will result in any photos that are currently in the photostream album on your device, that are older than 30 days old, not being added back.

How to find all routes that are going out an interface in IOS-XR.

Hi all,
So if I have the following set up in IOS:
interface GigabitEthernet7/0/0.265
encapsulation dot1Q 265
ip vrf forwarding test
ip address 1.1.1.1 255.255.255.252
ip verify unicast reverse-path
end
ip route vrf Apollo 2.2.2.0 255.255.255.248 1.1.1.2
I can see all the routes that are going out the interface using show ip cef command:
ios-router#show ip cef vrf test GigabitEthernet7/0/0.265
2.2.2.0/29
nexthop 1.1.1.2 GigabitEthernet7/0/0.265
1.1.1.0/30
attached to GigabitEthernet7/0/0.265
1.1.1.2/32
attached to GigabitEthernet7/0/0.265
In case of IOS-XR (ASR9K 4.3.2 or 4.3.1) the same setup and command shows only
attached routes:
router static
vrf test
address-family ipv4 unicast
   2.2.2.0/29 1.1.1.2
RP/0/RSP0/CPU0:TST_riga-sb7-pe-asr9#show cef vrf test bundle-ether2.265
Prefix              Next Hop            Interface
1.1.1.0/30          attached            Bundle-Ether2.2220333
1.1.1.0/32          broadcast           Bundle-Ether2.2220333
1.1.1.1/32          receive             Bundle-Ether2.2220333
1.1.1.2/32          1.1.1.2             Bundle-Ether2.2220333
1.1.1.3/32          broadcast           Bundle-Ether2.2220333
Is there any command to see all the routes that are going out an interface without complicated parsing
of the configuration, recursive show cef commands etc.?

You can accomplish this with the "show route" command. Here is an example:
P/0/RSP1/CPU0:ASR9006-E#sh route next-hop tenGigE 0/3/0/2
Tue Oct 8 15:34:58.046 UTC
Codes: C - connected, S - static, R - RIP, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - ISIS, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, su - IS-IS summary null, * - candidate default
       U - per-user static route, o - ODR, L - local, G - DAGR
       A - access/subscriber, - FRR Backup path
Gateway of last resort is 172.18.87.1 to network 0.0.0.0
D    10.95.248.1/32 [90/128512] via 10.129.56.210, 4d00h, TenGigE0/3/0/2
C    10.129.56.208/30 is directly connected, 4d00h, TenGigE0/3/0/2
L    10.129.56.209/32 is directly connected, 4d00h, TenGigE0/3/0/2
O    10.242.142.240/30 [110/20] via 10.129.56.210, 3d11h, TenGigE0/3/0/2
                       [110/20] via 10.129.56.214, 3d11h, TenGigE0/3/0/3
D    192.168.1.16/32 [90/128512] via 10.129.56.210, 4d00h, TenGigE0/3/0/2
D    192.168.20.39/32 [90/128512] via 10.129.56.210, 4d00h, TenGigE0/3/0/2
RP/0/RSP1/CPU0:ASR9006-E#
Thanks,
Bryan

How to fix an ipod that is frozen

my ipod start to turn differnt colors and when it turn back to its regular color then it froze and now i cant cut it off or type in my code to open it what should i do should i get it fix or do some else?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

How do fix ipod 4gen that wolt turn on?

I have a ipod that just wolt connect to iTunes or turn on how do I fix this?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

How to fix my router that I messed up.

Similar Messages

Maybe you are looking for