How to install the driver of the 'SCSI and RAID Host Controller'

Hi,
I have two Windows XP(32Bit) installations:
•Windows XP SP2(32Bit) which is old and it seems as if it is infected by some viruses.
•I have installed another fresh clean Windows XP(32Bit) SP3. However, I have found that there is no category named with ''SCSI and RAID Host Controller'. However, when checking out the old version of Windows XP, I found 'SCSI and RAID Host Controller'
is there. (Screen shot below)
The new Windows XP(32Bit) SP3, there is no 'SCSI and RAID Host Controller'
My motherboard is:
My Desktop Computer(Intel P 4, 512MB of RAM, and Graphics Card with 256MB of RAM.
]I am seeing that most computer doesn't has the scsi / raid controller . in the old Windows XP on my computer that SCSI and RAID controller exists, and it it has not a yellow mark on it.
When I installed a new windwos XP 32Bit SP3, no SCSI/RAID in divice manager .
My computer sound on new Windows XP doesn't work , however, on old Windows XP SP2 works well. I have a buitl-in sound card. SCSI and RAID controller category in the device manager on the old Windows xp SP2 is realted to sound card,I don't think.
Thus, What drivers would let the 'SCSI and RAID Host Controller' added in the device manager?
A man should convert his anger and sadness into strength to continue living in this life.

If you open the case and shine a light on the motherboard you can usually see both the manufacturers name and the model printed on the pcb somewhere. You should also normally see this information on the first POST screen when you turn on the PC.
Otherwise Google "775i65G" like I did.
Here are the driver downloads (assuming it is an Asrock 775i65G R2.0 and not an R3.0)
http://www.asrock.com/mb/Intel/775i65G%20R2.0/?cat=Download&os=XP
You should install the inf driver first. Hopefully after you do that you will see your desired listing in Device Manager.
With regard to the AMR driver and the HDMR driver, you can find some information about these here :
http://en.wikipedia.org/wiki/Audio/modem_riser
Unless you actually have something plugged into these risers, it is probably not necessary to install the drivers.
However, the drivers for the integrated C-Media audio chip and the Realtek Lan chip may prove useful.
It looks like the motherboard has integrated video but if you are using a graphics card it will not normally be necessary to install the VGA driver.
You can download both the manual and the installation guide here
http://www.asrock.com/mb/Intel/775i65G/?cat=Manual
And if "SCSI and RAID Host Controller" is still not shown in Device Manager, don't worry - because these functions are not supported by your motherboard (again assuming it is an Asrock 775i65G)
Thanks a lot,
First of all, when saying that I have multi-operationgs systems, I mean there are two operating systems installed on my PC(SP2, SP3) both are 32Bit. The first Windows SP2(NOT installed by me) has all multimedia audio card installed
well, and has SCSI and RAID Host Controller shown the device manager. However, only the VGA is not installed on Windows SP2. However, the second one Windows SP3(Installed by me) has VGA not installed, Multimedia audio NOT installed, and there is no SCSI and
RAID Host Controller in device manager.
First: Why did the CPUz, specy didn't detect motherboard name, and only detect the model. IF I need to open the case and shine a light on the motherboard you can usually see both the manufacturers name and the model printed on
the pcb somewhere, then what benfit would be there from hardware detection software?
Second: Yes, my motherboard has integrated video, and integrated audio card
However, this doesn't mean that I don't need to install them since the Vidoe controller is not properly installed (it is a default VGA ) Also, Multimedia audio controller is not functiong at all.
Finally: if And if "SCSI and RAID Host Controller" is still not shown in Device Manager in Windows XP SP3, because these functions are not supported by my motherboard, then why is 'SCSI and RAID Host
Controller' installed/shown in the device manger in Windows XP SP2 on the same PC???
A man should convert his anger and sadness into strength to continue living in this life.

Similar Messages

How to install display driver on the Sattelite Pro 4600?

I just can't find the option to do so. Can someone explain to me on how I can do this?
I don't see a dislpay option at the device controller.
What option is it?
Thanks in advance!
All help will be greatly appreciated.
Message was edited by: Boetje

Hi
The newest display driver you can download from the Toshiba website.
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp
Control Panel System -- Device manager -- Display adapters right click on the graphic controller update driver or install driver.
In this case the driver source is the download place of the graphic driver.
Good luck
Bye

How to install archlinux2008.6 from the hard drive?

How to install archlinux2008_6 by archlinux2008_6_i686.iso in hard drive?
i get the booting files(archlive.img,vmlinuz26) in the archlinux2008_6_i686.iso and put them in c:\
in the grub command mode the use of these code:
root (hd0,0)
kernel (hd0,0)/vmlinuz26
initrd (hd0,0)/archlive.img
boot
i get those from : http://blog.chinaunix.net/u/31909/showart_1121360.html
but it stopped , some code printing on the screen...................it can not continue..
from the google i find :"this method must use the "vmlinz "and the "initrd.img",this files is from archlinux2008.03.iso
i don't understand .......
i must download the archlinux2008.03.iso?...........it's too much trouble.
How to install archlinux2008.6 from the hard drive? or who could give me the two files (the "vmlinz "and the "initrd.img") from archlinux2008.03.iso?
e mail: [email protected]
THS.
--------this is my topic for the first time in english, I hope that you can know what i said ~~~
Last edited by 自学linux (2008-08-29 03:14:54)

自学linux wrote:
http://blog.chinaunix.net/u/31909/showart_1121360.html
A waste of CD-ROM...........,in china, many people install linux just by iso,don't burn the iso,
could you give me the two files (the "vmlinz "and the "initrd.img") in archlinux2008.03.iso, those can't find in archlinux2008.06.iso
my email :[email protected]
Do you have a USB stick you could copy the image to? Where I live, a CD costs $0.50 at most. To put that into perspective. A coffee costs a $1.00. Either a CD costs a lot more than a coffee where you live or are you telling me you'd rather get a lot of grey hair than buy half a coffee?
Sorry I can't be of much help. I don't know how to do this method of installation. If you're desperate, you could try making an extra partition, and trying something with that. Take a look at these:
http://wiki.archlinux.org/index.php/Fas … nux_System
http://wiki.archlinux.org/index.php/Ins … her_distro
Last edited by solarwind (2008-08-27 04:37:59)

How to Install Windows 7 Without the Disc

1a) Here is very useful article from PCWorld.com. The article is entitled "How to Install Windows 7 Without the Disc" and means just what it says. The article also has links to Magical Jelly Bean Keyfinder and legitimate Windows 7 ISOs from Digital River, a licensed distributor of Microsoft software. The article lists "Step 1" as;
"Find your Windows 7 product key: Typically this 25-character alphanumeric string is printed on a sticker affixed to your PC or on documentation included with your PC. Alternatively, you can use a keyfinder program such as Magical Jelly Bean Keyfinder to pull your product key from the Registry. You need your product key to reinstall Windows."
1b) Using a key finder, however, is only useful if the Windows 7 product key was printed on a sticker (Microsoft Certificate of Authenticity) affixed to your PC, on documentation included with your PC, or sent via email by Microsoft. Assuming your computer came from one of the big brand computer manufacturers... HP, Sony, Dell, Gateway, etc... as most do, it uses a generic "mass activation" OEM SLP key. Trying to use this key by itself isn't going to work. This OEM SLP key needs to be mated with an OEM SLP certificate and an appropriate OEM BIOS with a proper SLIC table.
1c) Here is where ABR Beta With Windows 7 Support comes to the rescue. Follow the "How to use it" section of ABR for Windows Vista for information and instructions on how to use ABR. The steps listed for Vista apply to Windows 7 as well. Perform the "activation backup" to "backup" and save the OEM SLP key and OEM SLP certificate. Save the entire ABR folder to an external location for later use. This will allow you to pre-activate your "clean" Windows 7 install on the computer you pulled the key and certificate from.
1d) Now install Windows 7 from your new "Windows 7" disc or USB stick, following all prompts as needed. Don't enter a Windows 7 product key if request. Also, don't allow Windows to try to auto-activate. Once Windows is fully installed, run ABR "activation restore" to "restore" the previously backed up product key and certificate to the new Windows 7 install. Verify that Windows is activated, repeat "activation restore" if needed.
2) Here is another useful article, this time from SevenForums.com. This arcticle is entitled "Clean Reinstall - Factory OEM Windows 7" and provides detailed steps required to backup your computer, audit current hardware and software, locate software and drivers, install and activate Windows 7, and create a Windows 7 Backup Image of your fresh install.
Good luck.
Links to additional Windows 7 SP1 "Editions" and "Languages" can be found HERE and HERE.
Link to "ei.cfg Removal Utility". The "ei.cfg Removal Utility" is a simple tool that will remove the ei.cfg from any Windows ISO disc image, thereby converting the image into a "universal disc" that will prompt the user to select an edition during setup instead of being forced to use different discs for different versions of Windows 7.
Direct link to Windows 7 USB/DVD Download tool.
<Cross posted to Notebook Operating Systems and Software for Notebook, Laptop, and Netbook users>
EDITED by Frank on 8/28/2013
Please click the white KUDOS star to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

ervis,
Before formatting the hard drive you should have been able to use the HP Recovery Manager to create your recovery discs or perform a system recovery. This is provided the recovery partition wasn't already corrupt or damaged. If the "D:" HP Recovery partition is missing or damaged and you don't have a set of HP Recovery Discs, you will need to use the information in my previous post to get your computer up and running again.
The information in the document referred you to applies to several different "types" of installations;
Using ABRbeta is only needed if you have an active OEM factory SLP (system locked preactivated) installation of Windows. You use ABR to pull the factory key and certificate off the computer, to reuse it on the same computer with a clean Windows install.
If you are just installing Windows and are going to use the Windows 7 product key on the COA on the side of your computer, all you need to do is download the same version of Windows that your key is for and burn the ISO. Now install Windows answering or following all prompts as needed (except do not enter the Windows product at this time... it will be entered later). Once Windows has completely installed, enter the key and activate it. Your Windows 7 OA key should work on a SP1 install without issue.
The only thing I see that could mess things up, is the language of the install. If you are still having trouble activating Windows, please reference the ISO you download and a post a photo of your Windows COA
with the key erased or Xed out.
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

How do I get Mac OSX 10.6.4 to print to a Canon iRC2380 colour printer? Using the driver in the Mac's list doesn't work., How do I get Mac OSX 10.6.4 to print to A Canon iRC2380 colour printer? Using the driver in the Mac's list doesn't work.

How do I get Mac OSX 10.6.4 to print to a Canon iRC2380 colour printer? Using the driver in the Mac's list doesn't work., How do I get Mac OSX 10.6.4 to print to A Canon iRC2380 colour printer? Using the driver in the Mac's list doesn't work.

Not sure which driver you mean when you say "the driver in the Mac's list". Apple does not provide a driver for this device, so if you mean one of the default printers that are included with 10.6, like the Generic Postscript or Generic PCL, then these will only work if the optional PS or PCL print kits were installed in the machine. Given your inability to print then it would seem that you have neither kit installed. So this would require you to install the Canon UFR2 driver, which you can obtain via this link.
With the UFR2 driver installed, you add the printer using IP > LPD. Enter the IP address of the iRC2380, leave the Queue name blank and change the Name to iRC2380. Leave the Location field blank and in the Print Using menu, browse to the "Canon iR C2380/2550 UFR II (UK)". Click OK and then Add to complete the queue creation. You should now be able to print. Please reply if it does not work.

How come the driver for the validiy sensor has an older version but newer release date

Can someone please explain why the driver for the finger print reader has an older date but a newer version?
The one on HPs website := Driver Version 4.4.234.0 and Driver Date 24/09/2012.
Yet the one on my P.C. := Driver Version 4.5.235.0 and Driver Date 22/07/2009.
Is it worth updating or not?
I can't seem to get the add-on working on I.E. 11.0.3
Any advice appreciated.

Spyke,
Welcome to the HP Forum.
Short Answer:
If you are running the same version of the Operating System that you were running when the driver was installed, then it is likely your driver is fine as it is.
Based on your Example:
If you have upgraded your Operating System, and you are using Windows 8 or Windows 8.1 AND your system is among those supported by the "newer" driver, then you should upgrade.
Long Answer:
There are several Validity Sensor Drivers of this same revision - in the case of sp58869 , the driver has been issued as a compatible driver for the HP Envy M6 for both Windows 8 and Windows 8.1. The change might have required additional supporting libraries used with the driver and did not require changes to the driver software itself.
You didn't say which computer model you have nor the version of Windows you are running.
It is true the specific driver within the version class might make a difference if you have updated your Operating System since your own driver was issued for your computer.
It is true that reinstalling a "same version" driver can help if the driver on your system is corrupted. Driver corruption is normal to some extent -- leave a driver on a Windows computer long enough and one or two of the zillions of instructions can corrupt, links can be lost; data can become unstable due to library changes or registry errors.
Drivers control hardware. The fingerprint driver only controls the fingerprinter.
Software provides a means for the user to interact with the computer in an organized environment.
===========================================================================================
Sometimes a perfectly good driver can "look bad" -- certain data persists from boot to boot. This is normal and the fact that some data is immediately available at boot means the computer starts up faster and that the Operating System is available sooner to the user of the computer.
When things in the boot-to-boot instruction set get tangled, then things may stop working: TouchPad, mouse (external), fingerprint software, maybe even the keyboard. The login data profile for the user account may not set up properly.
Driver Reset / Clean-the-cobwebs off the computer:
Close all your programs and Shut down the computer
Disconnect everything (little Unifier for the keyboard / external mouse can stay)
Perform the Hard Reset for your notebook
Boot the computer and log in
Next...
If Internet Explorer 11 is a recent update from a previous version, and even if this is not an upgraded IE issue, it is important that you be running the most recent version of your fingerprint Software.
I am assuming a lot here -- including that you are running HP SimplePass Version 6.x.
Continuing that line of thought; you might find the following useful:
Simple Instructions to Upgrade HP SimplePass
Brilliant Post - How to Ask Your Question
Click the Kudos Thumbs-Up!
It is a nice way to say “Thank You”.
Although I strive to reflect HP's best practices, I do not work for HP.
Kind Regards,
Dragon-Fur

How to Install .CAP file in the Java Card?

Hi Friends..
How to install *.CAP* file in the Java Card?..
I've GPShell script as follows :
mode_211
enable_trace
establish_context
card_connect -readerNumber 2
open_sc -security 1 -keyind 0 -keyver 0 -mac_key 404142434445464748494a4b4c4d4e4f -enc_key 404142434445464748494a4b4c4d4e4f
install_for_load -pkgAID a00000006203010c01 -nvCodeLimit 500 -sdAID A000000003000000
load -file HelloWorld.cap
card_disconnect
release_contextwith that script i can load HelloWorld.cap file successfully..
Now, how to install the HelloWorld.cap file?..
if i add script : load -file HelloWorld.cap i got this error :
install -file HelloWorld.cap
file name HelloWorld.cap
Command --> 80E602001B09A00000006203010C0107A00000015100000006EF04C60201A80000
Wrapped command --> 84E602002309A00000006203010C0107A00000015100000006EF04C60201
A80030C859793049B85300
Response <-- 6985
install_for_load() returns 0x80206985 (6985: Command not allowed - Conditions of
use not satisfied.)i ask this question because when i tried to select the applet through its AID, by this script :
establish_context
card_connect -readerNumber 2
select -AID a00000006203010c0101i got this message error : select_application() returns 0x80216A82 (6A82: The application to be selected could not be found.)
but there's exactly any that AID in my Java Card..
here's is the list of AID from My Java Card :
C:\GPShell-1.4.2>GPShell listgp211.txt
mode_211
enable_trace
establish_context
card_connect -readerNumber 3
* reader name OMNIKEY CardMan 5x21-CL 0
select -AID a000000003000000
Command --> 00A4040008A000000003000000
Wrapped command --> 00A4040008A000000003000000
Response <-- 6F108408A000000003000000A5049F6501FF9000
open_sc -security 1 -keyind 0 -keyver 0 -mac_key 404142434445464748494a4b4c4d4e4
f -enc_key 404142434445464748494a4b4c4d4e4f // Open secure channel
Command --> 80CA006600
Wrapped command --> 80CA006600
Response <-- 664C734A06072A864886FC6B01600C060A2A864886FC6B02020101630906072A864
886FC6B03640B06092A864886FC6B040215650B06092B8510864864020102660C060A2B060104012
A026E01029000
Command --> 8050000008AAF7A87C6013BC0300
Wrapped command --> 8050000008AAF7A87C6013BC0300
Response <-- 0000715457173C2A8FC1FF0200937A55C288805D8F2A04CCD43FA7E69000
Command --> 848201001023CA18742D36165ED992CFF2146C3D51
Wrapped command --> 848201001023CA18742D36165ED992CFF2146C3D51
Response <-- 9000
get_status -element 10
Command --> 80F21000024F0000
Wrapped command --> 84F210000A4F004FF8BE1492F7275400
Response <-- 0CF0544C00004D4F44554C415201000009A00000006203010C010100010AA000000
06203010C01019000
GP211_get_status() returned 2 items
List of Ex. Load File (AID state Ex. Module AIDs)
f0544c00004d4f44554c4152        1
a00000006203010c01      1
        a00000006203010c0101
card_disconnect
release_contextPlease help me..
And please correct me if i'm wrong,,
Thanks in advance..

Any suggestions for my question?..
Please help me..
Thanks in advance..

How do i recover data from an external hard drive that was accidentally deleted? After I verified the drive, a message appeared that said my drive needed to be repaired. When I tried to access the drive again, the 700 Gigs of music is gone!

How do i recover data from an external hard drive that was accidentally deleted? After I verified the drive, a message appeared that said my drive needed to be repaired. When I tried to access the drive again, the 700 Gigs of music is gone!

Stop using the drive immediately, un plug it.
Buy a copy of ProSoft DataRescue 4 and use it to search for deleted files.

How to install ftp service on the system?

OS: SuSE Linux Enterprise Server 8
How to install ftp service on the system?
How to check and modify to use it?
I am not able to use FTP.
Regards,
D

Rohit,
If its about installation/Deployment of Agent- then its through SDM,
'configuration' can be manual or Atuomatic:
Manual-> refer the installation Guide which digesh has mentioned -(from page 20).
Automatic- Its through Diagnostics Setup through Solman -(Its bit easy).
Thanks,
Jagan

How to install forms 6i on the same machine oracle8i installed

I have oracle8.1.6 release 2 installed on microsocft windows 98. How do I installed forms 6i on the same machine. when I installed forms6i, it has overwritten the resgistry settings and I cannot run database any more. Please give me some ideas how to install all these on the same machine on windows 98 , operating system DOS.

<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Simon Jennings ([email protected]):
You need to use seperate Oracle homes.<HR></BLOCKQUOTE>
You have to install Forms6i on a different Oracle_Home not Default_Home, which I believe is where you installed Oracle8i.

How to package instrument driver in the user.lib or instr.lib directory

Hey guys,
I currently am using bunch of instrument drivers in my project.
In the VI form it works fine, but I noticed that once converted to an executable,
there are errors regarding the DLL that the drivers are calling.
Apparently the driver VI check if its being called in an VI or executable based on the current directory.
I dont think this is good/correct programming to begin with... but anyways since this driver is
saved in the instr.lib directory of LabVIEW, when I call it from the executable the default path becomes
XXX.exe/1abvi3w/instr.lib/.../.../VI above.vi
I saw this post which talks about how vi's in instr.lib and user.lib will get the path 1abvi3w in an executable but never talked about how to deal with it.
so my question is can i solve this problem smoothly without copying the entire driver.lvlib into my project and
editing the VI above? i am fine with creating wrappers for driver vi's but would to like to avoid editing the driver vi's themselves.

doradorachan wrote:
I dont think this is good/correct programming to begin with...
I don't disagree, but there is a reason this code was written like that (you might note that it doesn't actually work) - before 2009, EXEs were built as flat directory, so stripping twice would bring you to the folder. Because of the addition of libraries, where different files have different names, this was no longer possible, so 2009 builds the EXE as a zipped hierarchy of folders, which is why the check for a folder succeeds even inside the EXE.
There are a couple of things you can do:
Replace the VI path with the Application Directory primitive. This is designed to function differently in an EXE. Understandably, you don't want to do that.
Check the 8.x checkbox in the advanced page of the build settings. This will make the code work correctly, but if there's LVOOP code with VIs of the same name anywhere, it will create extra folders that you need to move around with the EXE.
Add the driver to the project (just the lvproj, don't actually copy the files) and then set an explicit destination in the build for its VIs as an LLB in the data folder. This will place the driver VIs in an wLLB, which is external to the EXE and should then strip correctly. I can't say I have much experience with this, but I'm assuming it should also work with code that was originally in user.lib. This is probably the cleanest solution in terms of number of files because you only have one extra file.
Try to take over the world!

Installing a driver for the Apple Keyboard in Boot camp windows

I recently installed Boot Camp, VMware and Vista on my Mac so that I could move all of my computing on to one computer (I use a few programs that aren't available for the iMac). In Windows I cannot use the number pad for input - I can only use the numbers just above the letters. This is a major inconvenience because I input numbers often. I have tried to search for the driver for the Apple Keyboard that is compatible with windows, but have been unsuccessful.
Anyone know of a fix for this?
Thanks!

I tried putting in the Leopard disk and running setup.exe and that went through the motions of installing all of the drivers, but after I restarted the windows machine it still doesn't recognize my keyboard. This may be a system wide issue, because when I work in Windows it also tells me that I do not have a camera installed for video chat. At first I thought this was just part of the price I had to pay to have a Mac and use windows on it, but now I'm thinking that my drivers were not installed properly because I know a camera is installed internally (obviously - its a less than one year old iMac all-in-one).
Can anyone think of something that I'm not doing? I have gone into the control panel in the Windows machine and tried to update my driver, but it keeps telling me that the driver is correct (it has windows driver for a standard ps/2 keyboard).

How to install flash player for the gaming app "raptr"?

how to install flash player for the gaming app "raptr"?

Hi,
If you wants to install flash for any browser just visit http://get.adobe.com/flashplayer/ from that browser and click on "Install Now" button to install flash player for that browser.
But since i have found that raptr is a standalone game so raptr support team would be the right contact who can guide you well that which Flash player plugin they are using in their game. And this is what i have found on there support page Raptr wants me to download "Flash for Other Browsers". Where do I get that? : Raptr Support
You can follow the steps on that link, I hope it will solve your problem.
-Varun

How to install several instances of the same application on a computer?

Hej,
I have an application in LV 2009, where I have created an installer. The installer installs to a directory called \Receiver relative to the Program Files directory. If I install this once to a computer, everything is OK.
However, I want to install the same application twice on the same computer. There should be no conflicts between the two applications, since I can configure them to work on different directories and ports. But if I call the installer again, and selects another directory, nothing is installed and I get the message "Installation Summary - No software will be installed or removed". It seems like the installer ignores that I have selected another directory, and just uses the default directory, relative to the Program Files directory.
Anyone knows the trick, how to install several instances on the same computer ?
BR, Jan
Jan Nielsen
Freelance system analyst and LabVIEW programmer

Hi Jan,
This is so because each installer has a GUID that is used to check whether the application needs to be upgraded or not. (It's a Microsoft function).
What you can do is create a new installer with a different GUID (copy the installer in the projects), and check witha text editor whether this GUID has changed.
But any specific reason you need two seperate installs? You can run the application twice with a specific INI token:
allowmultipleinstances=True
Ton
Free Code Capture Tool! Version 2.1.3 with comments, web-upload, back-save and snippets!
Nederlandse LabVIEW user groep www.lvug.nl
My LabVIEW Ideas
LabVIEW, programming like it should be!

Need help ...just bought a mac mini, how to install adobe lightroom4 without the cd-rom?

need help ...just bought a mac mini, how to install adobe lightroom4 without the cd-rom?

You could download it as a trial version, and enter your serial number when prompted to buy.
https://www.adobe.com/cfusion/tdrc/index.cfm?product=photoshop_lightroom

How to install the driver of the 'SCSI and RAID Host Controller'

Similar Messages

Maybe you are looking for