How to properly install airport extreme?please help

please help me install this airport extreme
i think im doing everything right but i dont know
please help
thanx

When changing ISPs (or networking equipment) it's always a good idea to start from "scratch" in configuring your equipment.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Power-up the modem; wait at least 10-15 minutes.
Power-up the base station; wait at least 5-10 minutes.
Power-up your computer(s).
In this basic configuration, computers connected to the base station, either by wire or wireless (as appropriate for the base station type), should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options.

Similar Messages

How do i install airport extreme on a windows pc and route it to another windows desktop?

How do I install airport extreme into a windows desktop pc and then successfully route it to another windows desktop?

The AirPort Extreme Base Station (AEBS) is an Internet router that supports both wired and wireless network clients. You can connect both of your desktop, using either media, to the AEBS for network connectivity.

Ethernet Patch Cable from One iMac to AirPort Extreme Please help!

Hi, I have an iMac on one side of my home office, and a cable modem connected to my AirPort Extreme. I just bought a 25 ft. patch cable to run and connect to the router for faster speeds, but it is not working. I tried connecting it to the AirPort and the modem, and I did not get a light on the AirPort extreme or on the modem (I have disabled the wireless functionality on the gateway so it is just a modem now). I noticed that the cable has metal on the sides of the plug. Does that mean anything? How can I connect this and get it working properly?
Please help me!

your post is a little confusing
your imac is on one side of your home, and both your cable modem and extreme are on the other side of the house?
temporarily move the imac to the same side and try a different cable, seems like a cable issue

How do I install Airport Extreme + Bluetooth 2.0+EDR card on new G5?

I just received the card (Part# MA252G/A) in the mail but have no instructions on how to install it. The Apple website makes it seem like you have to have a BA in computer science to do it, so I'd like to see what's involved before attemting the install myself. Mind you, I've built computers from scratch so I'm inclined to believe I can so this myself with a little help.
Thanks!

Hi Nick -
Installation instructions that accompany cards are often sketchy as configurations can vary considerably from one system to another. If you take a look at the User's Guide that came with your G5 you should find the instructions you need for installing any type of card. In fact, my G5 User's Guide provides specifics for Airport Extreme installation. Check in the Index under 'Installing' & post back with detail if you have any problems. I think you'll find it rather straightforward.
Good Luck |:>)

Installing airport card: please help me!

I have put it into my friends clamshell ibook g3,..following the right instructions for physical installation under the keyboard,. but when i turn on the laptop, no new hardware is detected, and there is none in the system properties, or whatever its called,.. So basically nothing happens,. Additionally, the software in the CD is already on the computer (as it is Mac OS X 10.3.9). Any ideas? Any weblinks that have more detailed advice about these problems? Is there any way of finding out if the card just doesnt work?
Thanks very much,
Michael

You should be looking to setup the airport card through the Network preference in System Preferences. Select "Airport" from the "Show" popup menu. You may have to "Select Network Port Configurations" from the "Show" popup and check "Airport" first in order for it to appear in in the "Show" popup.
Additionally System Profiler should list the Airport Card under the network area.
Note: there is no "new hardware detected" notification after installing new hardware under MOSX as there is in Windows.
--Bill
MacBook Pro Mac OS X (10.4.5) No Longer Buzzing

HT3024 after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

Hi David,
Have you done a PRAM reset, CMD+Option+p+r...
http://support.apple.com/kb/HT1379
In fact, do 3 in a row, takes a bit of time.
Tried resetting the PMU for PB/iB?
http://docs.info.apple.com/article.html?artnum=14449

I installed lightroom 5 with a 30 day trial and it finished. Yesterday I installed cc and when I open LR5 I need a serial number. What do I do/how do I get one? Please help Tank you

I installed lightroom 5 with a 30 day trial and it finished.
Yesterday I installed cc and when I open LR5 I need a serial number.
What do I do/how do I get one?
Please help, Thank you.

Your photos remain in place, the catalog you have been using will remain. After you install Lightroom from the CC, all you have to do is open your existing catalog and continue right where you left off.

How to install AirPort Extreme card in eMac?

I just recently acquired a 2005 G4 eMac (the top-of-the-line model with the SuperDrive and 160 GB hard drive), and I am trying to install an AirPort Extreme card into it. Apparently I think the instructions must differ from this one:
http://support.apple.com/kb/HT2596
Since this is for the older AirPort cards.
I pushed the card in all the way, logo facing downward, screwed in the antenna, etc., but the Mac still won't recognize it! What should I do to get it working?

Numerous eMac users who installed Airport Extreme cards in the past have brought up that the Extreme card is a very tight fit in the eMac Airport slot, especially compared to the original Airport card. Often, the card appears to be fully seated, but is actually some fraction of a millimeter out. After seating the card according to all the instructions, you have to push hard on the edge of the card to get it to really seat all the way, hard enough to just start to push the 50-lb eMac away from you (don't try this with the eMac on the very edge of the table or desk!). I ran into exactly that putting an Extreme card in my in-law's eMac, and I had already read other's warnings; that may give you some idea how firmly you really need to push the card once it feels as if it's seated.

I intended to install windows on my macbook, but I removed Mac os X wrongly! Now I don't know how to install Mac again please help me.

I intended to install windows on my macbook, but I removed Mac os X wrongly! Now I don't know how to install Mac again please help me.

I still don't know which version of OSX you have but assuming it's 10.7 or 10.8 .....
You need to press command-R (at the sound of the chime) to get into recovery, try that, if it does not work try command-option-R for Internet Recovery.

HT4623 How do I install the iOS 4.3 on my iPhone 3GS ? I've tried direct links but it says safari cannot install this ? Please help !

How do I install the iOS 4.3 on my iPhone 3GS ? I've tried direct links but they it says safari cannot install this ? Please help !

You can not install anything but the current version of iOS. If you have a 3Gs, then you can install 6.0.1 by plugging it into your computer running iTunes (10.7 or higher). If you have a 3G, 4.2.1 is the end of the line.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

How do I connect airport extreme to seagate hard drive using windows

How do I connect airport extreme to seagate hard drive using windows?

First the AirPort Extreme Base Station (AEBS) cannot share out an external HDD attached to its USB port unless it is formatted in either HFS+ or FAT16/32. It will not work if the HDD is formatted in either NTFS or ExFAT.
If the HDD is formatted properly, when you access the AEBS with the AirPort Utility, does the HDD show up properly on the Disks tab of the utility?
If it does, then you would access the HDD as any other network share, using the following format: //servername/sharename. In the case of the AirPort Disk (a HDD attached to the USB port of either an Extreme or Time Capsule), the "servername" would be the Extreme's Base Station Name, and the "sharename" would be the volumename of the HDD.

How do I use Airport Extreme to limit internet time for my kids? His computer is hardwired to the modem.

How do I use Airport Extreme to limit internet time for my kids? His computer is hardwired to the modem.

You can set up daily time limits for each computer that connects using wireless, but it is not possible to do this when a computer is connecting directly using a wired Ethernet connection.
Open Macintosh HD > Applications > Utilities > AirPort Utility on your Mac and click Manual Setup
Click the Access Control tab below the icons
Select Timed Access
For more details on this, click the Help menu at the top of the screen and enter the following phrase into the search box:
Controlling access to your wireless network
A more sophisticated approach would be to use a service provided by OpenDNS. From your computer, this would allow you to monitor web sites visited, and block any unsuitable sites. More info is here:
http://www.opendns.com/landings/familyshield

How do I use AirPort Extreme to be able print from my MacBook Pro AND a PC. If I connect printer into AirPort, I can only print on laptop. If printer is connected to PC hard drive, I can only print on desk top. How do I configure this to make both print?

How do I use AirPort Extreme to be able print from my MacBook Pro AND a PC. If I connect printer into AirPort, I can only print on laptop. If printer is connected to PC hard drive, I can only print on desk top. How do I configure this to make both print?

If you have not already done so, your chances will really improve if you....
1) Connect the printer to the USB port on the AirPort Extreme
2) Download and install Bonjour Print Services for Windows on the PC

How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

How to properly install airport extreme?please help

Similar Messages

Maybe you are looking for