How to Remove ZD7000 Antenna Wires from the Hole?

UPDATE: The Maintenance and Service Guide mentions that the antenna wires are attached to a card; that's why I cannot simply pull them out through the hole. There may be enough slack so that, for my purposes, I won't have to disconnect the wires.
I'm finding some issues with the step-by-step instructions that I referenced below.
BB
Hi,
I'm disassembling my ZD7000 laptop to replace the DC power jack. I started following the steps at http://www.ifixit.com/Guide/Repairing+HP+Pavilion+​ZD7000+Motherboard/2878/1.
Everything went well until I got to Step 14, where I'm instructed to "Disconnect the 2 wires connecting the monitor to the rest of the laptop." In the picture, the antenna wire is one of the two wires highlighted with a red box. (Although the picture is somewhat confusing, because it shows a hand touching a third wire that is not highlighted.)
The HP Service & Maintenance Manual says, "Remove the 2 antenna cables from the hole and routing channel in the top cover." Since they are antenna wires, I assumed I could simply pull them out through the hole. However, I gave up after exerting as much pull pressure as I dared, which was a lot.
Am I missing something? I suppose I could cut the antenna wires and resolder them during reassembly.
Any suggestions would be greatly appreciated.
Thanks,
Bill
This question was solved.
View Solution.

As indicated in my update, this issue has been solved

Similar Messages

  • How to remove my credit card from the App Store

    How to remove my credit card from the App Store

    I used a pre-loaded credit card so when it ran out i had problems, primarily because it wont let me download or update anything until the "billing problem with the last transaction" was resolved. I dont really care if the purchase goes through but i want to be able to update stuff again and it wont give me the option to select 'none' under payment type. do i have to put another card on there just so i can "resolve the billing problem" and then i have  to take it off again or is there a way around this or is it a never ending cycle?

  • Any ideas on how to remove a small scratch from the screen or whether it is covered by apple?

    Any ideas on how to remove a small scratch from the screen or whether it is covered by apple?

    Call Apple Care and ask them if your computer is still under warranty. 

  • HT3702 How to remove my credit card from the iPod

    I want to remove my credit card from the app store

    On an iOS device go to Settings>Store>Apple ID>View Apple ID>Payment Information>None.
    If "None" is not an option, you may want to contact iTunes support:
    http://www.apple.com/support/itunes/contact/

  • How to remove a static class from the Runtime of the JVM

    I want to remove a static class from the Runtime of the JVM.
    My goal is to clear the cache of the "InetAddress.getByName(String host)" static method.
    Thanks in advance.
    Floweb

    Sorry, It means a class that has been loaded in the JVM by the call to a static method......
    Floweb

  • How to remove a Java instance from the config tools

    Hi,
    I would like to remove a java instance from the config tool since that server does not exist anymore.  Is there a way?
    Please le me know.
    Thanks
    Jean

    Jean,
    I think you can do this if you remove the entries of your Instance from instance.properties file located under the below path.Take a backup of the file first then do the changes and Restart the server once done.
    /usr/sap/SID/JCInstanceno/j2ee/cluster/instance.properties
    Hope this helps.

  • How to Remove Jar File name from the screen of nokia 40 series

    hi
    i have the problem with running midlet.
    the jar file jame is always visible on the screen, how to remove that ?

    >
    Prasanna Kumar wrote:
    > Hi ALL
    >
    > I am using  file adapter and I what to create file name dynamically by acesssing PO number and time stamp from the payload using variable substution.
    > But the problem is I am getting ":" in time stamp field value and it is not acceptable for file name .
    > So could you please tell me a way that I can remove this ":" from that particular field value and create the file name dynamically.
    >
    > Note 1)Add Time stamp option will not help me as we require a time stamp of particular zone.
    > 2) Dynamic Configuration code is also not use full as I am using 1:n file creation
    does the time stamp with the ":" a part of your output file?
    else use a replaceAll function in your mapping and replace the : with empty string then use the value in the variable substitution
    Another option is use the normal BPM for 1: N message flow. The use a simple java mapping that will introduce a dynamic configuration and you can create the file name as you want. the java mapping will be used in the flow of messages from BPM to target system.
    ref: /people/shabarish.vijayakumar/blog/2009/03/26/dynamic-configuration-vs-variable-substitution--the-ultimate-battle-for-the-file-name

  • How to remove links to adobe from the image viewer

    On my site I need to display lots of pictures. I used the
    image viewer flash element from the `insert`-`media` tabs.
    Everything works great, but the first few pics in the
    slideshow are clickable, and link to the adobe home page. How could
    I remove the links and make the pics not clickable. I already went
    into the flash element properties window and made the `image links`
    and `image link targets` blank. I don`t know what else to try.
    Please help!
    thank you: Tibor

    It's only necessary to post once. No answer usually means
    that nobody knows
    the answer....
    Murray --- ICQ 71997575
    Adobe Community Expert
    (If you *MUST* email me, don't LAUGH when you do so!)
    ==================
    http://www.projectseven.com/go
    - DW FAQs, Tutorials & Resources
    http://www.dwfaq.com - DW FAQs,
    Tutorials & Resources
    ==================
    "serestibi" <[email protected]> wrote in
    message
    news:frm8qo$26v$[email protected]..
    > On my site I need to display lots of pictures. I used
    the image viewer
    > flash
    > element from the `insert`-`media` tabs.
    > Everything works great, but the first few pics in the
    slideshow are
    > clickable,
    > and link to the adobe home page. How could I remove the
    links and make the
    > pics
    > not clickable. I already went into the flash element
    properties window and
    > made
    > the `image links` and `image link targets` blank. I
    don`t know what else
    > to
    > try. Please help!
    > thank you: Tibor
    >
    >

  • How to remove a Sharepoint list from the Powerpoint app on iPads??

    Hello,
    I have added a Sharepoint "place" in Powerpoint app on an iPad and cannot find a way to remove it, the address of the SharePoint page/place/list has been changed so it is no longer relevant to me. Any tips?

    Hello Scott,
    I did post a question but for some reason it didn't post. What I typed was removed for some reason. So I'm trying again. I'll keep trying until it posts. I had installed a 3rd party sound editor program which added a sound device to the list with Mic and line in. It's also in the output list. All I need to do is remove the device and then AU will allow me to select line in as an input device. Right now AU is confused by the extra device and wont let me select an input device. AU is a developer app. But that's not the problem. The problem is removing the device from the list of sound devices.
    If someone knows where this device might be and how to remove it, please let me know.
    Thanks,
    Dave

  • How to remove (delete) FB contacts from the contact list.

    I'm really new to my new Mac and having a bit of trouble trying to delete all the contacts that were downloaded to my contact list from Facebook. I have tried highlighting one and deleting it that way, but, the 'Remove from Group' doesn't light up.
    I tried putting them in a particular group, such as FB contacts, then deleting that group. But, they still remain in the group titles 'All on My Mac'. How do I get them deleted from that group??

    To turn off Facebook contacts:
    1) Go to Contacts
    2) Click Group on the top
    3) Uncheck All Facebook
    Then you shuold just see your regular contacts.
    Good luck.
    Mr Bill

  • How to remove a 3inch CD from the slot loading drive??

    I have am external adapter for various IDE external devices. The drivers came on a 3 inch CD.I put the CD in the slot it did not appear to go all the in and it will not eject using the normal methods. Anyone run into this situation??
    Bob

    I was able to remove the disk quite simply. I slid a business card through the center of the slot. I aimed the card slightly upward toward the top of the drive. I inserted the card in about an inch and a half. I then took a mediun size paper clip and straightened it out. I bent the last millimeter down about one millimeter forming sort of a hook. I then inserted the hook end in about an inch and a half on top of the business card (away from the drive mechanism).I then rotated the paperclip so that the hook end dropped into the hole in the CD. I then slid the paper clip, the the business card and the CD out together It worked great first try. The drive still works.
    Bob

  • How to remove only one row from the database using labview6.1

    using labview 6.1 I create a table with various rows and columns and store bulk of data's in them.,, what procedure should I follow to remove only one paticular row from the database? Help me out with an example please,,
    Thanking you in advance!

    Hi,
    If you have the database toolkit you can delete a row using just a SQL Query to "DB Tools Execute Query.VI"
    Example:
    DELETE FROM Table name Where SerialNum='Value' And Date='Value' And Time='Value'
    See also attached VI
    Best Regards
    Johan
    Attachments:
    Delete_a_row_in_a_database_table.vi ‏48 KB

  • How to remove a dynamic symbol from the stage?

    I'm loading dynamically copies of a Library symbol with a button click. Question is, when I move around in the timeline, I don't want to see the symbols at certain points. Can I loop through the json file and remove each symbol from the stage? Or is there a better way of accomplishing this?
    Being new to Edge Animate, I'm also unsure as to the names of the symbols as they are placed on the stage. If I use the browser's developer tools, I can see that the divs are named Stage_90, Stage_91, Stage_92 etc. However doing something like the following does not seem to work:
    sym.$("Stage_90").hide();
    I appreciate the help. Thanks again.

    I got it. It should be:
    $("#region1").remove();  
    // # was missing.
    I actually added that to time 0 on the main timeline so when I got back there it removes the image.
    It's not working from the symbol yet but I guess I should eventually get it working from there instead.
    Thanks for your time.

  • How to remove a "learned" word from the dictionary

    Somehow I managed to add some mis-spelled words to my dictionary and I cannot figure out how to remove or edit these "learned" words.
    Any help would be appreciated.

    What version of Pages?
    Peter

  • How to remove Credit Card number from the account

    Dear Sir/Madam,
    Someone used my Creadit card to buy credit and I agreed initially.
    Now i want to remove my creadit card number from her account and disallow her to use it. But it seems the credit card infomation can not be removed and she still can buy credit using my credit card.
     I checked with her account and it seems my credit card number is always shown there, no matter how I try.
    May I know how can I do?
    Thanks
    Solved!
    Go to Solution.

    Hi,
    You can delete a credit card if you have used it to buy Skype Credit, but you cannot delete a card that is being used for recurring payments (a subscription or Auto-recharge). You have to cancel the recurring payment first.
    To delete a credit card:
    1. Sign in to your account:
    http://www.skype.com/go/myaccount
    2. In the Account details section, click Billing & payments.
    3. On the Payment settings page that appears, click Stored payment details, and then next to the credit card you want to delete, click the Delete button.
    For more help with updating your credit card details, visit:
    https://support.skype.com/faq/FA10486/
    Hope this helps.
    Rod
    If you found this answer helpful, please give Kudos. If it resolved your issue, mark it as a solution to help others. Thanks!

Maybe you are looking for