How to set date and time on apple tv

how to set date and time on apple tv

Assuming this is not the first time you have used your Apple TV
    1.    You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
    2.    Also try restarting the router.
    3.    If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
If this is a new Apple TV, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123.

Similar Messages

  • How do I set date and time on apple tv?

    How do I set date and time on apple tv?

    Fixed the same problem, STEPS
    1. Reset your apple TV
    2.It will again stuck on that setting, ignore it by press menu
    3. Unplug ethernet wire
    4. Try to connect with wifi, it should be work with wifi connection as mine.
    5. Then you can switch back Ethernet wire after get fixed.
    Thanks. Lemme know dude if it's work.

  • HT1595 setting date and time on apple tv

    Cannot set network date and time using apple tv

    Welcome to the Apple Community.
    Assuming this is not the first time you have used your Apple TV
    You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
    Also try restarting the router. (Also try removing it’s power cord for at least 30 seconds)
    If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
    If restoring from the Apple TV doesn't help, try restoring from iTunes using a USB cable.
    If this is a new Apple TV, in addition to trying the above, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123.

  • HT3180 Can't set date and time on apple tv

    I cannot set date and time. Help!

    It is having trouble connecting to the network. Make sure location is set correctly. DNS should be set to automatic (settings - general - network). If on wifi try ethernet. Reboot ATV and router.

  • HT3180 setting date and time - my apple tv get stuck and says it needs to set the network date and time.  Does anyone know how to do this?

    My apple tv gets stuck and says it need to set the date and time on the network.  Does anyone know how to do this?

    I was able to get my Apple TV working again by downgrading the firmware following the instructions in this message:
    https://discussions.apple.com/message/20008613#20008613
    In case that message disappears, here's my translation:
    1. Connect your Apple TV to your computer via USB. Don't plug in the power cable.
    2. Download the older 5.0.2 firmware from Apple here:
    5.0.2 (Apple TV 2): AppleTV2,1_5.0.2_9B830_Restore.ipsw
    5.0.2 (Apple TV 3): AppleTV3,1_5.0.2_9B830_Restore.ipsw
    3. Open iTunes and select the Apple TV. Hold down the option key and press the restore button at the same time.
    4. In the dialog that opens select the firmware that you downloaded.
    5. The restore process will take a few minutes. Once it's done plug your Apple TV back into your TV. If the date and time message persists just press the menu button to skip it. This got mine working again.

  • I bought my apple tv in USA and use in Indonesia, but I can't set date and time.

    How to set date and time so I can Home sharing with apple tv .

    Call the shop in NYC and find out.

  • Setting date and time in java mail

    I want to set date and time for the mail sent by my application.
    So how to set date and time for my mail.

              msg.setSentDate(new Date());Where msg is an instance of javax.mail.Message.

  • Geting and setting date and time in oracle using jdbc

    can u send me a sample snippet which shows me how to set date and time to a column in oracle database where the column datatype is date.
    and also send me the sample code to get the date and time from the above said column
    thanks in advance

    If you want DATE with time normalized to midnight, use java.sql.Date. If you really want time, with hours/minutes/seconds/millis, use java.sql.Timestamp.
    As for the best way to interact with the database, use java.sql.PreparedStatement and its get/setDate and get/setTimestamp methods. Those will escape dates for you properly.
    Look for a JDBC tutorial on-line to see how to do this, or http://www.javaalmanac.com for the java.sql package examples.
    %

  • All of a sudden my ATV came up with a message stating trying to set dat and time however cannot access. Could this be due to the recent hacking of Apple or is it something new. How do I fix?

    All of a sudden my ATV came up with a message stating trying to set date and time however cannot access. Could this be due to the recent hacking of Apple or is it something new. How do I fix?

    Welcome to the Apple Community.
    It's not related to any hacking.
    Try the following steps, check whether things are working after each step where appropriate, before trying the next.
        1.    Restart the Apple TV (Settings > General > Restart).
        2.    Restart the Apple TV by removing ALL the cables for 30 seconds.
        3.    Restart your router.
        4.    Reset the Apple TV (Settings > General > Reset > Reset all settings)
        5.    Restore the Apple TV (Settings > General > Reset > Restore)

  • HT1595 how do i access apple tv when screen is stuck at setting date and time

    how do i access apple tv when screen is stuck at setting date and time, have unplugged system,restarted router....

    Welcome to the Apple community.
    Assuming this is not the first time you have used your Apple TV
    You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
    Also try restarting the router.
    If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
    If this is a new Apple TV, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123.

  • Automatically Setting Date and Time - How often does it occur?

    Can anyone tell me exactly when Mac OS X retrieves the date and time from Apple's time server? Quite often, the time on my Mac is several seconds out from the correct time. When I open the "Date and Time Preferences", it seems to sync up with the correct time and everything is good.
    Is there any way to schedule when Mac OS X automatically sets the time, or how frequently over the course of a day it sets the time? Or, alternatively, does anyone know of a utility that I can use to accomplish this?
    Thanks in advance for any help you can give me.
    iMac 1.83 GHz Intel Core 2 Duo   Mac OS X (10.4.8)  

    Hi Barry,
    Thanks for your reply.
    I have a wristwatch that receives a radio signal which transmits the correct date and time from an atomic clock in Fort Boulder, Colorado. The watch automatically picks up this signal three times a day (in the early morning so as to get the correct time once we go on/off DST) and sets my watch to it. So my watch is always accurate (so long as it can receive this signal). I have an alarm clock that uses the same principle. It's actually kinda nice...I can look at my watch and KNOW I have the right time!
    At any rate, that's how I know my Mac's clock is out a few seconds...I just check it to my watch.
    The real reason I would like to be able to schedule this function (or, at least have it occur more often) is so my Palm TX gets the correct time from my Mac each morning. I automatically sync it to my Mac every morning, and one of the conduits actually synchronizes the Palm clock to the one on my Mac.
    I'm just curious to find out when exactly Mac OS X sets the clock. Does it happen once a day? Once a week? I haven't had my Mac for all that long, so I do not know what will happen when we go off DST this spring. Will OS X (based on the date) just bump up its clock by one hour, or will it actually get the correct time from Apple's time server and sync the Mac clock to it?
    And, if there's no way the change when this happens or the frequency with which it occurs, is there anyone out there who has written a utility which can do this?
    What about Automator? I'm new to the Mac world, so I am just learning about all this stuff. When I open the Date and Time System Preferences, the clock seems to sync up at that point. Could I use Automator to do this?
    As always, any help would be most appreciated.
    Thanks again for your reply, Barry!

  • How do I change the "Set Date and Time Automatically" server

    Is there a way to change System Preferences/Date & Time/Date & Time/Set date and time automatically from "Apple Americas/U.S. (time.apple.com)" to another time server instead?

    sig wrote:
    The menu has a drop down. But if you know the address of another time server I would think you can type it in.
    Yeah, that's not really a menu, but a "combo box", which is a combination of an edit field and pop-up menu. So you can choose from existing items or just type in whatever time server you want.
    charlie

  • The apple tv is stocked at setting date and time

    I Updated the Apple TV and now it requested to start the configuratio all over again and is stocked at setting date and time, can somebody help me?

    http://appletv2.com/stuck-on-setting-date-and-time-fix/

  • Having problem with the apple tv, because it still setting date and time and dont finish w the activation

    having problem with the apple tv, because it still setting date and time and dont finish w the activation

    That means it is having trouble connecting to the network. Make sure location is set correctly. Go to settings - general - network and ensure DNS is set to automatic. Check that your router is up to date. If on wifi try Ethernet.

  • I plug the Apple TV in and it just says setting date and time.

    When I plug the Apple TV in it just starts up setting date and time. Tried unplugging  it and resetting using the remote but it is unresponsive

    Welcome to the Apple Community.
    Assuming this is not the first time you have used your Apple TV
    You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
    Also try restarting the router. (Also try removing it’s power cord for at least 30 seconds)
    If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
    If restoring from the Apple TV doesn't help, try restoring from iTunes using a USB cable.
    If this is a new Apple TV, in addition to trying the above, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123.

Maybe you are looking for

  • Idoc Script strEqualsIgnoreCase make a wrong evaluation of logic values.

    Hi again, this question starts like the last one i put in forum Re: Cannot find metadata values in workflow queue but it´s absolutely different. I need some help customizing workflow action menues. I´ve created a custom component with an html resourc

  • Vendor list by company code wise with Acoount group..?

    Dear all   Can anybody expalin me how to get a report on vendors list by company codes wise with account group... 1.List of vendors company codes wise 2.List of vendors company codes wise with account group wise. Thanks sap-mm

  • How to make SAP Query additional field as one of the selection field ?

    Hi experts, I'm working on a AdHoc query. I added some Additional fields to the infoset. I put Abap code to populate this additional fields as output fields but I want to make these fields as selection fields also. How can I accomplish this ? I'd app

  • Mighty Mouse a Problem?

    I bought my mighty mouse in the weeks after it came out because i accidentally broke my original mouse which came with by iMac rev.a. I have had a few problems with my mouse in the past weeks and wanted to know if anyone has had similar problems. 1)

  • Service Manager "Error communicating with component" after moving SQL servers

    We just moved our SCCM database to a new SQL server and ever since, I've been getting stumped as to why I'm getting the following error each time I try to query the status of anything under the SQL server: Error communicating with component Admittedl