HP LaserJet 1100 strange issues

This printer was working just fine using the standard setup. I hooked it back up when I got back to my apartment and now it's not doing anything. The computer recognizes it. I've tried uninstalling the printer and resetting the printer system. The printer will print a test page just fine (if I push the button on the printer), as well. Here is the error I am getting:
Process: rastertogutenprint.5.1 [211] (brackets go around this)
Path: /usr/libexec/cups/filter/rastertogutenprint.5.1
Identifier: rastertogutenprint.5.1
Version: ??? (???)
Code Type: X86 (Native)
Parent Process: cupsd [15] (brackets go around here, too)
Date/Time: 2008-03-14 03:49:52.286 -0400
OS Version: Mac OS X 10.5.2 (9C31)
Report Version: 6
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Crashed Thread: 0
Dyld Error Message:
Library not loaded: /usr/lib/libcupsimage.2.dylib
Referenced from: /usr/libexec/cups/filter/rastertogutenprint.5.1
Reason: image not found
Now I've gone into the terminal and libcupsimage.2.dylib is right where its supposed to be. I have no idea how to tell if the file is corrupt or how to get another copy of it there to replace the existing one. Any ideas? Thanks in advance.
Edit: I just went through my crashlog and found this one from when I was trying to get it to go...essentially the same problem, except a different process was trying to access libcupsimage.2.dylib
Process: cgpdftoraster [511]
Path: /usr/libexec/cups/filter/cgpdftoraster
Identifier: cgpdftoraster
Version: ??? (???)
Code Type: X86 (Native)
Parent Process: cupsd [247]
Date/Time: 2008-03-14 04:05:10.466 -0400
OS Version: Mac OS X 10.5.2 (9C31)
Report Version: 6
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Crashed Thread: 0
Dyld Error Message:
Library not loaded: /usr/lib/libcupsimage.2.dylib
Referenced from: /usr/libexec/cups/filter/cgpdftoraster
Reason: image not found
Message was edited by: rfuree11

So, in case anyone else needs help with this in the future, LOOK CAREFULLY WHEN YOU ARE IN THE TERMINAL!! I'm an idiot and didn't realize that my filename had been corrupted. For some reason, one of the m's in the filename got replaced with 胭. Don't ask me why, don't ask me how, it just did. So a basic command later and all was good again. And for some of the people who aren't familiar with *nix commands, I just used the mv command to change the file name:
sudo mv libcupsi胭age.2.dylib libcupsimage.2.dylib

Similar Messages

HP Laserjet 1100 Print Issue

I have above printer connected to Windows XP Pro 2002 SP2 laptop system. When sending print job to printer the print queue appears to process normally (job shows up, changes status, then disappears). However printer never responds: lights do not blink and nothing prints.
I disconnect the printer and connect it to a Windows XP Pro 2002 SP 3 system (using same printer cable) and printer operates correctly! So the printer cable should be OK.
I connect a different printer--a Canon--to each computer system and it works correctly. So the print cable port on the laptop should be OK.
I downloaded the latest driver for the 1100 from HP site onto the laptop, removed the printer defn and re-added the printer...same problem.
Any thoughts as to why the printer is not responding when sending print job? Printer is still good...hate to toss it in the trash.
Note that these 2 computer systems are stand-alone (no networking between them) as is the printer.
Thanks.

Hi there. This is funny, or sad really. I have the exxact problem. When it doesn't print it says this printer is not connected.
That just can't be. What about firmware? While nosing around the HP site I noticed it says firmware needs to be updated.
I'm not sure how to do this.
Have a great day,
Zarifa

Barcode printing issues with Laserjet 1100 8.1 driver

Hi All,
I've ran into issues printing coupons to my Laserjet 1100 printer using Windows 8.1. This worked with no issues (and still does) in Windows 8. Looking at the driver versions, it appears that something was updated form 8 to 8.1.It seems this issue is related
to printing any barcodes. Has anyone else encounters this? Is there any way I can use the Windows 8 driver instead?

For anyone interested, the way I was able to fix this issue is with the
HP Universal Print Driver for Windows PCL6
http://h20566.www2.hp.com/portal/site/hpsc/public/psi/swdHome/?sp4ts.oid=4157320&ac.admitted=1399039456352.876444892.199480143
I selected Windows 8.1 x64, then downloaded the PCL5 driver and now the barcodes work.

[SOLVED] Can't get CUPS to add / detect HP Laserjet 1100 printer

I moved my computer downstairs... after a few weeks I decided to move my printer down and set it up. I had it working perfectly a few weeks ago before the move... however now I can't get CUPS to detect or add my printer. At first when I moved my printer downstairs the CUPS web interface had my previous setup still there and had my printer detected / added. However, printing jobs would just stay in the queue and never print. I did some googling and someone mention to remove the printer and re-add it. Well I tried to to that and got stuck on trying to re-add it. CUPS will not identify my printer now. Funny thing is I just now remember I had a similiar issue a few months back and I remembered now I fixed the queue issue just by unplugging the power to my printer and leaving it off for 5min then replugging it in. I have tried all the steps on the wiki and I can't seem to figure this one out. dmesg does output that it is detecting my printer. I have my printer hooked up via a mini parralel to USB cord. If you have any other questions for me please shoot
Unplugging and repluggin my printer gives me this msg in dmesg:
usblp0: removed
usb 6-2: new full speed USB device using uhci_hcd and address 4
usb 6-2: configuration #1 chosen from 1 choice
usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x4348 pid 0x5584
hp-toolbox also does not detect any printers. I have tried restarting cupsd... Any help is appreciated... I need to get printing up ASAP since school has started.
lsusb output this amongst other things:
Bus 006 Device 004: ID 4348:5584 WinChipHead CH34x printer adapter cable
If it matters I am using XFCE as my DE... I also do not remember using the CUPS interface to intially add the printer... I do not exactly remember how I did it... but the web interface looked completely new to me and I am rather sure that is not how I initially went about doing it... perhaps I used some GUI frontend for it...
EDIT: After reading the forum descriptions closer... perhaps this should be moved to the Workstation section.
Last edited by ugkbunb (2009-09-07 20:11:27)

skottish wrote:I'm curious why you're using gutenprint drivers for a HP printer. hplip provides everything needed for HP printers.
Tell you the truth... I have no idea how to change it or what not... I didn't even add that manually... just rebooted my computer one day and it appeared there.
hpsetup does not detect my printer
system-config-printer gives me an error when I try and add a printer. I manually specify the location to file:/dev/usb/lp0 ... I scroll down find HP LaserJet 1100 and the recommended driver is hpjis 3.9.8. I select that and I get the following:
There was an error during the CUPS operation: 'client-error-not-possible'
EDIT: I am about ready to chunk to this printer out the window... I have been messing with this for about a week now and I just keep getting two steps forward and then three steps backwards.
The system-config-printer dialog looked familiar and I believe that when I intially was able to set up my printer and had it working upstairs I used that dialog to add my printer.
Some googling brought me to this ubuntu bug report
Your USB-to-parallel adapter does not pass through the printer ID. The device is recognized as printer, but there is no information about manufacturer and model. Therefore system-config-printer and hal-cups-utils automatically assign the text-only printer to the unknown device.
In general you have to run system-config-printer and manually choose manufacturer and model.
That you cannot print at all is a bug of the "hal" CUPS backend. See
https://fedorahosted.org/hal-cups-utils/ticket/5
Try to do the following:
cupsctl FileDevice=yes
lpadmin -p <your print queue name> -E -v file:/dev/usb/lp0
This is an ugly workaround which works if you have only one printer (the one with the adapter cable) on USB. Does it work for you?
Now the problem is that I can not add my printer via the system-config-printer. However, if I go the CUPS web interface and hit manage printers the driver is listed as the following:
Driver: Local Raw Printer (grayscale)
Now I think that is my issue... I need to have it set to the correct driver... if I hit modify printer and select my Make/Model I get the following access error:
401 Unauthorized
Enter your username and password or the root username and password to access this page. If you are using Kerberos authentication, make sure you have a valid Kerberos ticket.
However there is no prompt or I do not know where to enter this information to.
Last edited by ugkbunb (2009-09-07 19:06:48)

MacBook + HP LaserJet 1100 + AirPort

I would like to print wirelessly using my HP LaserJet 1100 with my new MacBook, but it looks like it will be more difficult than I thought.
Problem #1:
My HP does not officially work with my macbook. Is GutenPrint or HPIJS the better solution for a driver and printing wirelessly (I suspect GutenPrint)?
Problem #2:
The HP uses a parallel port connection, not a USB connection. It looks like Sabrent, Sewell and Belkin all make USB to parallel port adapters, but whether or not one will work seems to be pretty hit or miss and specific to the computer/printer combination. Which one will (or is most likely) to work?
Problem #3:
As I said, I want to print wirelessly. I have read several posts that say that some printers don’t work with an AirPort base station, even if that printer works with the actual computer (I think it is because the printer does not advertise that it is available over the network). Does GutenPrint overcome this problem (as suggested here: http://discussions.apple.com/thread.jspa?threadID=825581&tstart=15)? If not, what workarounds exist?
MacBook Mac OS X (10.4.8)

How do you have it connected, USB adapter or parallel port?
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

HP Laserjet 1100

I send a document to the HP Laserjet 1100. The document shows up in the Queue. It then disappears from the queue as if it printed, but it did not print.
If I remove the paper, or turn off the printer, and then send the document to the printer, it hangs in the queue until I turn the printer on or put the paper back in the feeder.
It worked on Friday, last week, but would not work starting on Monday.
Also, I can print a test page from the printer self-test, but not from the printer properties in Windows 7.

How do you have it connected, USB adapter or parallel port?
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

LaserJet 1100 paper out indicator

My Laserjet 1100 refuses to recognize that there is paper in the paper feed slot. This means that I cannot use it to print. There used to be a kit that could be used to fix this, but HP seems to have stopped making it available. Is there another solution, or another source for the kit? Except for that problem, the LJ 1100 has been a great workhorse for me.

Hello,
A couple of possibilities come to mind......
1) Sometimes, restarting the product can clear a paper feed issue. Follow these steps to perform a reset.
Press the Power button ( ) to turn on the product.
With the product turned on , disconnect the power cord from the rear of the product.
Unplug the power cord from the wall outlet.
Wait at least 15 seconds.
Plug the power cord back into the wall outlet.
Reconnect the power cord to the rear of the product.
If the product does not turn on by itself, press the Power button ( ) to turn it on.
Then: On the product control panel, press and hold e Resume button ( ) for 2 to 3 seconds.
Best of Luck!!
(Although I am employed by HP, I am speaking for myself and not for HP)
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"
I worked for HP but my posts and replies are my own....Thank you!
*Say thanks by clicking the *Kudos!* which is on the left*
*Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

Strange issue with WEBI schedule Report

Hi All,
I have a strange issue with schedule WEBI reports, a schedule report runs for Hours , i reschedule it again by deleting the instance and the schedule report never got succeed even after running for hours.
Any idea???
regards

Hi Manoj,
1. Try to put some filters in the report and then run the report. if it takes less time, then probably your query is fetching very large data.
2. MDX query error may be the reason , this error come when a query runs endless, please try running the query 2-3 times, or when load on server is less.
Hope this will help,
Anamika.

Files transferred to external HD end up in trash - very strange issue

Hi,
I seem to be having a very strange issue, hopefully somebody can help or has seen this before.
Hardware: MacBook Air, Western Digital Passport external HD, 250gb, formatted NTFS.
Software: OSX 10.7 Lion, Paragon (allows me to write to an NTFS formatted HD)
Issue Summary: I copy something to the external HD; I empty trash; the file I copied is deleted from the external HD. It doesn't happen every time.
I do also seem to have a persistent folder in trash called "WD Sync Data" that won't go away unless I re-delete it as it's also in the root of the drive. Not sure if this is related somehow.
Recently I copied 3 video files inside a folder to the HD, then disconnected the HD. When I reconnected it a while later and noticed that inside the "WD Sync Data" folder in trash were the 3 files I'd copied. I then looked inside the same folder on the root of the drive and the files were there, instead of inside the folder that I'd copied to the drive, which had vanished. If I hadn't noticed and had emptied the trash, those files would've been deleted.
It's definitely happened more than once; last time I actually deleted the files from my computer after copying, then emptied trash, and they were gone from the external HD also.
I've only found one person who seemed to be experiencing a similar problem back in 2010. It sounds similar though it could've been user error: http://www.mac-forums.com/forums/apple-notebooks/188224-weird-external-hard-driv e-trash-problem-help-please.html
Has anyone experienced this or have any suggestions?

Quick update: I ran a verify then a repair in Disk Utility as there were a couple of errors. Hopefully this has solved the issue, however it'd still be interesting to know if anyone's come across this before and what caused it?

Oracle Identity Manager 9.1.0.2 & WebLogic Strange Issue

Hello,
I am running OIM 9.1.0.2 (new installation) and WebLogic 10.3.3 in a clustered environment. I am having a strange issue where the resolution is eluding me.
This install is running on Windows 2008 x64 Standard and using the x64 JRockit Java.
What's happening is when I configure the managed server to run as a windows service, OIM isn't detected on the server. I can bring up xlWebApp but an unable to log into that or the Design Console. When launching the Diagnostic Dashboard it statest that OIM isn't installed.
If I stop the service and log into WebLogic and start the managed server from within the Admin Console in WebLogic, everything works just fine.
Any thoughts on how to troubleshoot this and ultimately resolve this? The service correct startes the managed server as I can watch it start up in the admin console but when it starts that way, OIM isn't detected. Very odd.
Thanks,
Andrew

Oracle confirmed with us that it is certified for 10.3.3 though it may not be published yet.
At any rate I figured out the problem today. The script I used to create the service was missing the JAVA_OPTIONS section from the xlStartManagedServer.cmd file. Once I added that and re-created the service, all is well.
Thanks

Windows Vista and BPS0 - Strange issue

I just got a new HP Pavilion laptop with Vista and I have a strange issue:
All transactions work (SE80, RSA1, ...) except BPS0. The moment I enter TCode BPS0, I get completely logged out (all sessions). No error messages, no dumps. It just logs me out silently.
Is this happening only to me?
I use Windows Vista Home Premium edition and AMD Turion processor 64x2.
Any suggestions appreciated.
Thanks

i too recently bought hp pavillion and my problem is i cant able to logon it gives me error of 10054, connection broken, can you tell me which things restrict me to log on. any settings are there to be performed. do mail me, i have been trying from 2 week my id is [email protected]

Strange issue with RAM upgrade: It works but it doesn't! Please help.

Hello Everyone,
I have a very strange issue with my iMac since upgrading my RAM from 4 to 12 gig. When I first installed the new RAM it booted up and ran great. The next time I went to boot the iMac up it swtiched on but didn't get as far as the first white boot up screen. I tried turning it off and on a few times using the power on/off button but still no success. I decided to remove the RAM and reseat it. The computer then booted up again fine. Here's the problem though: when I went to switch my iMac on the next day it wouldn't boot up. Again, I took the RAM out and put it back in and the iMac booted up fine. I've checked the status of the RAM in the system profiler and it reports that everything is OK. So, I'm at a loss. Obviously, I don't want to go through this process every time I want to start up my Mac. Any ideas/solutions would be very gratefully received.
Many thanks in advance.

I completely agree with you. It will be one of the 3 issues you outline. The machine was bought brand new and has never given me a problem. It is just the introduction of the new RAM that has started a problem. However, I did just risk a restart and it booted up fine. I don't know if a restart is any different to shutting down and then pressing the on/off button to start the computer. Maybe my last reseating has done the trick or maybe my thinking is flawed because restarting involves a different process to booting up by pressing the on/off button. I don't know.
In the part of the world I'm sitting in it's night time now so I will leave the diagnostics running and check the results in the morning. I hope the issue is now resolved anyway. This sort of thing takes me back to my dark PC days although in this case I know it's probably not the Mac's fault.
Thanks again. Very much appreciated.

Laserjet 1100 drivers for win 7 pro 64bit

need drivers for the above
details
Laserjet 1100 mono
model" s4224a
sggjo25836
these are the only details on the sticker on the back of the printer..
It does NOT have product number.
comes up wth this error
Error: This product number is not associated with the serial number provided. Please review your records and make any necessary edits.
Have tried upper & lower case with the same result.
Help please!

Hi,
The drivers for your printer are already included within Windows Update.
Follow these steps to install the printer on a Windows 7 PC:
http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?spf_p.tpst=kbDocDispl...
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

How to define the HP LaserJet 1100 Series(SHARP AR-M550U )?

Hi,
Once the SHARP AR-M550U got plugged to my HP laptop on which Windows 7 Home 64BIT is installed, this screen shot showed me.
I have checked for drivers using Windows Update. But it didn't find any. As this screen shot below.
I don't have the drivers disc which came from manufacture.
This is hardware ID for SHARP AR-M5501UB104
I have googled for USBPRINT\SHARP AR-M5501UB104, but no results showed.
Also, What new featuers are there in HP LaserJet 1100 Series(SHARP AR-M550U ) different from other HP LaserJet P2015 PCL6 and HP laserJEt Professional P1102?

could anyone please reply to me since I am in an urgent need for using this this photocopier.
By entering my Enter product name/number, which is SHARP AR-M550U and pressing 'serach', these results found:
Product search resultsSoftware & driver downloads
Results for "sharp ar-m550u" (22 products)
HP NC550m 10Gb 2-port PCIe x8 Flex-10 Ethernet Adapter
HP NC550m 10Gb 2-port PCIe x8 Flex-10 Ethernet Adapter
HP Pavilion t500 Desktop PC series
HP Pavilion t550m Desktop PC
HP SFP and Mini-GBIC BX10-U Transceivers
HP X115 100M SFP LC BX 10-U Transceiver
HP SFP and Mini-GBIC SX Transceivers
HP X126 1Gb/s SFP LC SX MM 550m 850nm Transceiver
HP Networking Switch Redundant Power Cords
HP X290 500 U 1m RPS Cable
Micron M550 256GB mSATA-3 Solid State Drive
Micron M550 256GB mSATA-3 Solid State Drive
HP Tape Drive SAS Cables
HP 1U SAS Ext-Min 1x-4m Cable Assembly Kit
HP 1U SAS TP I-E 3HDDs X 1Tape Drive X4M Server Cable Assembly Kit
HP SFP and Mini-GBIC BX-U Transceivers
HP 114 100M SFP LC BX-U Transceiver
HP X112 100M SFP LC BX-U Transceiver
HP 3PAR Drive Chassis
HP M6710 2.5 inch 2U SAS Drive Enclosure
HP M6720 3.5 inch 4U SAS Drive Enclosure
HP SecPath Licenses
HP SecPath U200-M 1 Year Anti-spam Service License
HP SecPath U200-M 1 Year Anti-virus Update License
HP SecPath U200-M 1 Year IPS Update License
HP SecPath U200-M 1 Year Web Content Filter Service License
HP StoreFabric Premier Flex OM4 Cables
HP Premier Flex LC/LC LSZH 50/125u OM4 MM 1.6mm Zipcord Short-boot 4M Cable
HP Premier Flex LC/LC LSZH 50/125u OM4 MM 1.6mm Zipcord Short-boot 6M Cable
HP Premier Flex LC/LC LSZH 50/125u OM4 MM 1.6mm Zipcord Short-boot 10M Cable
HP Premier Flex LC/LC LSZH 50/125u OM4 MM 1.6mm Zipcord Short-boot 25M Cable
HP Premier Flex LC/LC LSZH 50/125u OM4 MM 1.6mm Zipcord Short-boot 50M Cable
HP Premier Flex LC/LC LSZH 50/125u OM4 MM 1.6mm Zipcord Short-boot 100M Cable
I am quite confused which ones should be installed to define the SHARP AR-M550U on my HP laptop on which Windows 7 64bit is installed.

I can't find HP LaserJet 1100 printer driver.

I got My Mac to "see" my PC's shared folder and I'm so excited. Then I tried to print but it didn't have my print driver: the HP LaserJet 1100. Is there some way to get it or some other way to make it work?
Thanks.

No I am. I started to answer a different question. Sorry. If I could delete my post I would have.

HP LaserJet 1100 strange issues

Similar Messages

Maybe you are looking for