HP LaserJet P1505n stops printing and blocks network interface

I have been using my P1505n for over two years without any problem. But it suddenly stopped printing. The scenario is as follows:
1. The P1505n is connected to a wired home network with reserved IP address in the DHCP server.
2. The P1505n is used from Ubuntu 10.4, 11.4 , Windows XP and Windows 7 without any previous problems.
3. The last partial successful print job stopped in the middle of a page leaving the rest blank: no paper jam.
4. I have reset the printer several times: turn off + press Cancel & Go + turn on while holding the two buttons down.
5. The first reset was successful: the toner level going from 40 to 100%. The next ones may have been successfull too.
6. After each reset and also after each power-on, I can ping and access the embedded web server.
7. Whenever I send a print job, the print queue on the computer (all OS behave identically) says "printing" and stops. I can cancel/remove the jobs from Ubuntu.
8. After the printer receives the print job, it silently blocks the network interface (no ping nor web) and doesn't print anything. No movementsm no LED blinking either: just nothing happens.
What is the reason for this problem? And how do I solve it?

Hi firedude007,
Welcome to the HP Forums!
I see that your HP Laserjet P1102w stops printing files from your Mac but not on Windows, and I am happy to help!
For further assistance, I will need to know the following information:
The version number of the Mac Operating System. To find the exact version, visit this link. Whatsmyos.
If the printer is connected, Wireless, or USB.
If the printer is able to make copies by itself.
In the meantime, I would try the following:
Reset the printing system. Mac OS X: How to reset the printing system.
Verify and repair disk permissions. Disk Utility 12.x: Repair disk permissions.
Hope to hear from you, and thank you for posting!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Similar Messages

  • HP laserjet m1536dnf mfp print and scan is very slow

    Hi Sir/Madam,
    HP laserjet m1536dnf mfp print and scan is printing and scanning slow on network. Sometimes scan is not work. That's why I have to reinstall the printer driver. So how to increase print speed?
    Thanks in advance,

    Hi riz1_4444,
    Welcome to the HP Forums, I hope you enjoy your experience!
    I understand the printer is printing and scanning slow on the network.
    I will be happy to help you.
    Make sure printer is connected directly to a wall outlet.
    Try printing a hardware test on the printer to see if it prints slow or not.
    Printing a Configuration Report. Select Method one: Print a Configuration Report from the printer control panel.
    I would restart the router to see if this will resolve the issue.
    Try another Ethernet cable.
    If you are still having issue then test the printer by connecting the printer to the computer by a USB cable to see if it is something on the network that is causing it to slow down.
    Hope this resolves your issue for printing slow over the network.
    Thank you for posting on the HP Forums.
    Have a wonderful day!
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • HP LaserJet m1120n multifunction printer scan to network

    Hello,
    I have an issue making the scan to network function to work between HP LaserJet m1120n multifunction printer and Snow Leopard.
    Printing is working fine and it was added via IP.
    I checked the HP site for the instruction, but it does not work.
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01846935&cc=us&lc=en&dlc=en #N441 the scanner does not show up.
    http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=3 447597&lang=en&cc=us&taskId=135&prodTypeId=18972&prodSeriesId=3447595 does not show scanner driver for 10.6
    anyone using the same printer/scanner that could give me tips to get this working? thank you in advance.

    my setup is different.
    the printer is connected via ethernet to an airport extreme and printing is fine.HP Director/Scan is not detecting the printer over the network.
    i saw this one hp site(i forgot yhe link and i couldn't find it again) telling us to include network devices in preview and the scanner does not show on the options.

  • When syncing iPhone with iTunes I get an iTunes stopped working and the network connection timed out message. I reinstalled iTunes and checked settings still no go.

    When syncing iPhone with iTunes I get an iTunes stopped working and the network connection timed out message. I reinstalled iTunes and checked settings still no go.

    Disable or turn off your firewall, anti-virus, and all security software and try the download again.
    Stedman

  • Bridging wireless and wired network interfaces

    Hi,
    Is it possible to "bridge" the airport and ethernet network interfaces on a macbook pro using Leopard (10.5.7) ? I do not mean Internet connection sharing. That results in NAT.
    I recently got a desktop in my room which doesn't have a WiFi interface. I wish to connect its wired interfaced to my mbp's wired interface and give it access to the wireless network my mbp is on. To do this I would need to bridge the wireless and wired interfaces on my mbp. All the results I find online to do this only talk about Internet Connection Sharing ..
    thanks,
    regards,
    Puneet

    You can turn on IP Forwarding to achieve most of what you're after:
    sudo sysctl -w net.inet.ip.forwarding=1
    This will have the Mac forward packets from one interface to the other without NAT.
    However you still need to use separate subnets, and may need to play with routing to get everyone to talk to each other.

  • HP Laserjet p1505n doesn't work over network with Yosemite

    Ever since upgrading the machines in my house (Mac Pro, iMac, MBPretina, MBAir) to Yosemite, I have not been able to use the network attached Laserjet p1505n that used to work flawlessly under 10.9.  It doesn't appear in the printer tab in System Prefs where it used to pop up.  Anyone have any experience with this?  The printer will install via USB just fine on the Mac Pro, MBPRetina, etc.  Thanks!

    To see the printer in the Default view of the Add printer window, a protocol called Bonjour is used by the printer and Mac. This protocol is having issues for some users who have upgraded to Yosemite. Until the issue is resolved you may be able to use one of the IP protocols to connect to the networked printer. To do so you will need to find the IP address being used by the printer. If the LJ-P1505n has a control panel, you may be able to generate a report showing the network settings.
    Once you have the IP address you can open Printers & Scanners and click the plus button to add a printer. Then click on the IP icon and enter the IP address of the HP in the Address Field. In the Protocol field, change to HP Jetdirect-Socket and in the Queue field, leave this blank. You can then change the Name from the IP address to LJP1505n and in the Use menu, select the P1505n printer. Click the Add to complete the printer creation and then see if you can print.

  • Can't get my hp laserjet p1505n to print with verizon mifi

    I changed internet provider from broadband to Verizon MIFI and now my printer doesn't work. II have a HP Laserjet P1505n and it was networked to my desk pc and my laptop. What can I do to get it working again??
    Thank you
    Connie Moore

    Check this page from HP
    http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&obje ctID=c01863616&jumpid=regR1002USEN
    Maybe you can find your drivers there —or at least some information.
    As of your printer, turn it on and connect it to your mac, then click in software update —chances are that you can download the drivers.
    Good luck

  • Hp laserjet 3030 would print and now won't

    When I plugged in the hp laserjet 3030 all-in-one to my mac mini and added a printer it worked!
    Then, I found the driver CD that came with the printer so I thought I'd install the HP Director so I could scan etc.
    Now the printer won't print, I used to get an error message that said something about a postscript and the number 13. I don't recall the entire message because I no longer get it, instead ...
    I see in the printer que window that it is starting the job, then it just quits without anything being printed.
    I've tried to unistall and install the printer multiple times. I'm not sure if I'm doing this right. I go to printer/fax preferences and remove any printers from my list. I've gone to user/library/printers and deleted any printers in that folder. I'm nervous to delete items in the mac hardrive/library/printers folder.
    I've repaired disk permissions multiple times.
    No luck
    The strange thing is that I can use the hp director to use the scanner. The scanner works but printing won't go through.
    Please, please help.
    Dan

    Hi Brotocol,
    Thank you for your reply!
    Please try the following:
    Uninstall the software. Uninstalling the Printer Software.
    Clean boot the computer. How to perform a clean boot in Windows.
    Disable any antivirus programs. Disable antivirus software.
    Disable any firewall programs. Windows Firewall from start to finish.
    Create a new user account. Managing User Accounts and Logins (Windows 8).
    Reinstall using the HP Printer Install Wizard for Windows.
    Tips for troubleshooting wireless connection issues
    The following tips can help you troubleshoot and avoid wireless connectivity issues. You can try these tips separately or in combination to get a successful wireless signal.
    Move the printer and the computer closer to the router, but no closer than 6 ft (1.8 m). Wireless signals can be weaker at greater distances between the printer and the router.
    If you are experiencing an intermittent wireless connection, try restarting your router. Consult your router manufacturer, Internet service provider, or network administrator for instructions on how to restart the router.
    Remove any metal objects between the printer, the computer, and the router. Objects such as refrigerators, microwaves, or metal bookcases can interfere with wireless transmission.
    Move any device that emits radio signals, such as microwaves and cordless telephones, farther away from the printer. Such devices can interfere with wireless signals.
    Make sure the router is broadcasting at 2.4 ghz and not 5 ghz.
    Hope this information is helpful!
    RnRMusicMan
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to say “Thanks” for helping!

  • HP LaserJet CM1415fnw stop printing

    My CM 1415fnw stopped printing today from every computer in the house. I have had this printer for about a year without any other problems. The wirless network test report states "pass" but the HP Toolbox FX states printer not connected to the network. I have reinstalled from factory settings and started from beginning again. Still same result. The only thing that has changed recently is I had to install a new wireless router in the house. That said, the printer was working fine for the last 3 days on the new router. Any ideas?

    It may be that the printer got a new IP address from the new router.   You might look at your printer properties on your pc and look under ports, open up the port and see what IP address it was configured for.  Now print out a config report from your printer and see if they match.  If they are different that may likely be the issue.  To help elimate this problem, (some wireless router will force IP address changes quite often) the best thing to do is assign a manual IP address on your printer.  Please refer to your manual or other support to see how to do that.   You can use the printer's control panel to do this but you just need to make sure you don't choose an ip address that your router might try and give to another device (computer, etc).
    Although I work for HP, my posts and replies are my own.

  • HP LASERJET 4000 PARALLEL PRINTER - CONNECT TO NETWORK

    I have a HP LaserJet 4000 printer with parallel interface currently connected to a desktop computer (WIN 7) via hardwire connection.  I have a wireless home network with another desktop and several laptops that I would like to be able to print to this printer, preferably via a wireless interface.  Does anyone know if this is possible and if so what it would take in additional hardware.  Even though this printer is no longer sold, in terms of usage it is still new, on the first toner cartridge!
    thanks

    Can you elaborate as I'm not that tech savvy but have a similar issue.  I have an HP Laserjet 2100M that I love as a "workhorse" printer.  I previously had this printer and an Epson Stylus Photo R800 "networked" so I could print to either from my MAC.  I recently moved from CT to FL and would like to replicate the network.  In retrospect, I think my network was facilitated by the HP printer being connected directly to an old PC which must have been like the printer server you described.  The old PC did not move to FL so I now have a MAC, a cable modem, an Airport router and a new PC laptop that I would like to connect.  Plus, I'm looking to buy an all-in-one to have the functionality that I had before the move (a separate fax machine and an HP printer-scanner-copier that also didn't make the move.  (As an aside, I was looking at the HP 8600 to buy and was concerned as it doesn't say it supports Windows 8 so I have to find something else.)  
    Sorry for beng so longwinded but I'm at a loss for which direction to go and recognize I'm in over my head but beleive what I want to do can be done (I just don't kow how)

  • Vista 64 - LaserJet P1505n - Word - printing only first 2 pages

    I have a new Dell laptop with Vista 64 and HP LaserJet P1505n. When I try to print a multi page document in Word 2007, it only prints the first 2 pages. I have to tell it to print pages 3-4, 5-6, 7-8, etc. to get the rest of the pages. If I convert the same document to PDF, all pages print fine. Has any one resolved this issue? 

    it's getting more interesting:
    I connected the printer directly via USB; Voila, works like a charm
    Using wireless: problems.
    Now it's specifically the wireless option why I choose this printer, so USB is not really an option.
    Strange thing is: the HP Utility cannot find the printer wireless, not even if I enter the (static) IPv4 address.

  • Laserjet 1200 stopped printing on Mac Book Pro

    I've had my MBP since May timeframe and my JetDirect shared LJ 1200 has always worked and just stopped recently. I loaded the upgrade to 10.4.8 around the same time. I get no errors on sending a document to the printer, it doesn't show in the queue but does show in completed documents even though it didn't print.
    I've deleted and reinstalled the printer in OSX to no avail. Other Windows machines sharing the printer can print fine. I also use a networked Officejet 7310 (recently installed) with no problems printing from the MBP.
    Any suggestions would be appreciated.
    Kevin
    Mac Book Pro Mac OS X (10.4.8) 2 GB, 2.16Ghz

    Hello Kevin,
    As you have just done the 10.4.8 update, run the Repair Permissions located in Disk Utility. This may be all that is needed.
    If it doesn't, and since the job leaves the Mac, it could be queue related rather than being due to the protocol used. I've seen this symptom before when the wrong queue name is used for LPD printing. For the JetDirect cards, the queue name should be raw.
    You can check the queue name that has been used by viewing the CUPS printers page. Open your browser and type "http://localhost:631/printers". You will see a list of the printers installed and for the LJ1200, look at the line Device URI. It should show something like "lpd://192.168.44.146/raw".
    If it is incorrect the best thing would be to delete the printer from the Printer Setup Utility and add it again with the correct information.
    If the queue name is correct, then run the Reset Printing System function located in the Printer Setup Utility menu. This will delete the printer and force you to add it again.
    Regards,
    Paul

  • Im using HP laserjet M1120N MFP printer and its required WIA driver.

    hi, 
    im using HP laserjet M1120N MFP printer.
    last time i dont have any issues to printer or scan, and lately i cant scan
    and only able to print out.
    its required me have WIA driver. anyone know how to fix its.
    thanks

    Hello zuzack97,
    I am sorry, but to get your issue more exposure, I would suggest posting it in the commercial forums, since this is a commercial product. You can do this at http://h30499.www3.hp.com/hpeb/
    I hope this helps.
    Regards,
    Happytohelp01
    Please click on the Thumbs Up on the right to say “Thanks” for helping!
    Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
    I work on behalf of HP

  • [HP Color LaserJet CP1518ni] Stopped printing black ink documents when Magenta toner finished

    Hi there,
    I have a HP Color LaserJet CP1518ni.
    I just printed about 200 pages of black ink documentation.  The black ink cartridge is still about 38% full.
    Although none of these printouts involved colour, the printer started flashing the message: "Replace magenta cartridge".
    Since then, it would no longer print.  Again, I am only attempting to print black ink docs, and I even tried turning off the colour print option to no avail.
    The printer queue on my macbook shows the doc as 'printing' and 'sending', and then it disappears, with nothing happening on the printer itself.
    If I push the 'X' button on the printer, it says 'cancelling print' or something like that.
    Is there any way around the problem of the printer not printing anything once one of its cartridges runs to empty, even though the printjob does not need that colour cartridge?
    Thank you!
    Steve

    How can I find the Toolbox FX on Windows 7 Professional? I can only find information about Windows XP and Windows Vista. When I  go to my Start button, and go to All Programs , there is no HP option or folder;therefore,I can't find the Toolbox FX.
    My printer ran out of magenta toner, but all I want to do is print in black ink (which I have plenty of).
    Can anyone please help me?

  • Canon Multifunction MF5700 Stopped printing and is seen as unavailable.

    Came into the office this morning and our Caon MF5700 was not printing from any workstation. I tried to ping the IP address and the device was unreachable. I reset the Network IP settings and I am able to sucessfully ping the new IP for the printer. I can also type the IP into a browser and log into the Admin panel for the MF5700. But Windows still shows the device as offline. I have powered down the printer and restarted all the workstations. Still showing as offline in Windows. I have several different versions of Windows in a peer to peer network. Windows 7, Windows Vista, and Windows XP. None of the workstations can print a test page or any othe document. Has anyone else run into this issue?

    Hi tcastaldo and Dinsdale,
    If printhead cleanings did not get your PIXMA MG5320 to print correctly, it would appear as though your PIXMA MG5320 would require service.
    For your service options, please contact our support group using the following link:
    http://www.usa.canon.com/cusa/consumer/standard_display/contact_us_consumer
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Maybe you are looking for

  • Open links in new window

    How do you setup a link to open in a new window? I have two webcams on my iWeb and would like them to open in a new window. my iweb : www.puppybark.com   Mac OS X (10.3.9)   iMac G4   Mac OS X (10.3.9)     Mac OS X (10.3.9)  

  • 11.5.10.2 Workflow-only users licensing

    Hi, I have a question on licensing required for the users who only have a 'Workflow user' responsibility in OEBS, version 11.5.10.2. We'd like to start using iExpenses, but currently lots of potential approvers do not have any access in OEBS, I wonde

  • My ipod touch 4g got wet today and the screen is now very dim.

    I used it like normal afterwards and then i locked the screen and now it can barely see anything. Am I SOL?

  • F4 help for select options based on parameter value

    hi all, I need a help to create an F4 help for select options for object id based on parameter value of object type, I mean once an object type is given the f4 help should contain object id's only of that type for each option. Regard's, Girija Modera

  • Tracking infotype chnages

    plz reply Hello, I am coding  to get fileds of  infotpe changes . I can not use standard program RPUAUD00 for my requirement. for FM  HR_INFOTYPE_LOG_GET_DETAIL  it exports only itab & fields, but i need to fetch head-opera too, which i can not get f