HP Mediasmart Server EX490 stopped booting; health light blinks blue forever

My server recently stopped responding on the network. I power-cycled it to reboot, but it never came back up. The network conection light goes solid blue (and the server shows up in the router's list of clients), but the health indicator continues to blink blue indefinitely (as long as 36 hours at one point) and I can't view any files or remote desktop in.
This has continued through a variety of reboots. I attempted to use System Recovery to restore the system, but was never able to get the server to enter recovery mode (health indicator turning violet). I tried using recovery anyway just in case (both with a direct ethernet connection and over the network), but it always failed on step 3.
I wondered if the boot disk had died, but I removed it and hooked it up to another computer and was able to successfully view files, so it's at least not totally dead.
I'd appreciate any further suggestions on things I could try to get it back up and running.

I have the same problem ..... Will not boot up, two 1t drives, I removed the drives tested to see if data was on.. yes... has dat. System will not boot to get it. I can not reinstall software either. HELP !

Similar Messages

HP MediaSmart Server EX490 - Unable to find server/install Connector

Hi,
Would really appreciate any help on this issue since I am at my wit's end. I have a EX490 with 2 2TB drives on it. Been so long ago but pretty sure one is a backup of the other.
I began to have trouble logging in to the Windows Home Server Console a couple of weeks ago but didn't think much of it because I could still access the mapped drives on my computer. I had chalked it up to me typing in the wrong password.
Well, the hard drive on my computer crapped out and had to reformat it. However, whenever I try to install the Windows Home Connector, it tells me that it can't find my server. I get that same error message when I try to install the software on any other computer.
I'm starting to freak out a bit because I'm afraid I won't be able to access all the pictures and videos on the EX490.
I've tried searching Google for solutions but all the solutions involve accessing the server somehow and I'm not able to do so. My next attempt is to take out one of the drives and connect it to my desktop as a hard drive but need to run out to the store to buy another SATA cable. Not sure if that will work but don't really know what else to do.
Any advice or insight would be greatfully appreciated. Thanks!

It sounds like a Local Area Network (LAN) issue where you have this MediaServer installed (home, small office),
A LAN Router REBOOT may be necessary to clear .. and assign a TCP/IP address to the HP MediaSmart Server.
HP EX490 MediaSmart Server
Support Page
HP MediaSmart Server Setup Poster
Assure that your MediaServer is obtaining a TCP/IP address from your LAN Router.
You may need to login to the Router's Adminsitrative Page to check this.
This is covered in Chapter 2 of the User's Manual.
HP MediaSmart Server User Guide

Can't access ex495 mediasmart server

My HP EX495 media smart server is runnng Windows Home Server. The device went off-line the other day and I could not connect to the device through ethernet nor USB. The nick has a solid green light and a flashing yellow lignt. My guess is it is sending out a signal but not receiving one. Any idea how to fix the problem? I've tried rebooting; sending WOL messages; reseating the drives; but still can not access it.
Any guidance would be apprciated. Thank you.

Try this? HP MediaSmart Server EX490 - Solution to LAN going offline at boot-up ‎05-18-2013 03:09 AM After swapping out a defective Netgear router, I started to experience problems with my MediaSmart server going offline immediately after boot-up. I could also see from the router stats that the EX490 established an Ethernet connection at 10Mbps when powered off, but not following boot-up. I could even use WOL to start the server, but it would drop the LAN connection shortly afterwards, without ever coming online. I tried various Cat-5 cables and 3 different routers, but I could not get the aqua LAN LED to stay on for more than about 30 seconds after boot. I could see the yellow LED on the RJ45 NIC port flash very occasionally, but that was about it. I managed to establish a PC to EX490 direct connection and so could get into the server via Remote Desktop, which again suggested there was nothing fundamentally wrong with the NIC port or cables. I tried upgrading the Realtec PCIe driver to no effect, checked there were no conflicting LAN addresses, DHCP services, etc., etc., and even considered doing a server rebuild. Eventually, I found a solution that works for me. Using the peer-to-peer LAN connection and Remote Desktop, go to the EX490 Device Manager, select the Realtek PCIe GBE Family Controller Properties, Advanced Tab and scroll down through the Property window to Speed and Duplex. Change Auto Negotiation to 100Mbps Full Duplex, save and reboot the server. It seems in my case that the EX490 is no longer coping with negotiating connection to a Gigabit LAN (still not sure why), but slowing the card down to 100Mbps is giving me a rock-solid connection. I hope this post will help others who may be contemplating using their MediaSmart as an expensive bookend or doorstop.

HP vs17x monitor power light blinking

After I bring my computer out of standby mode my vs17x monitor's power button/light blinks blue, with the sound of what I assume is power going to the speakers, and continues unless I hold it down to turn it off or unplug it.
After some waiting and clicking I can get it back to normal, but as far as I know it's just random clicks that bring it back up
Any diagnosis/suggestions?
Thanks
-Update-
-This morning I was able to get my screen back up by pressing the power button on my compaq keyboard (crescent moon, which puts in standby/brings up standby/shutdown/restart menu)
Also all the icons on my desk were rearranged, put to the left/top, but I'm unsure if that was due to my random clicking
-This afternoon I after walking away for a bit (after I turned it on) the screen came back up
Message Edited by J_Winn on 10-15-2009 03:52 AM
Message Edited by J_Winn on 10-15-2009 12:48 PM
This question was solved.
View Solution.

Thanks so much for the hint, J_Winn.
Once, I opened the unit, I could see that three of the capacitors looked different the tops were bulging ( bulging capacitor ).
I replaced those three and all was well.
Disassembly hints:
- The curved plastic top piece of the pedestal stand pops to allow access to the 3rd pedestal screw.
- The entire pedestal assembly then slides toward the bottom.
- Use a small flathead screwdriver to pop off the front cover. (but not tiny, that was my initial problem)
- Write the colours of the four wire pairs in pencil on the metal screen so you remember which goes where.
- Remove the small metal cover from the larger metal cover to access the ribbon cable connector.
- To disconnect the ribbon cable from the circuit board, carefully pry up the black strip on the connector.
Reassembly:
- The power button cover, bottom of the U points to the back of the case.
- The other button cover piece has tabs that fit into the small switch circuit board
Hope this helps!

HP MediaSmart Server EX475 Backup stopped working

I have an HP MediaSmart Server EX475 (service pack 3). My network includes a Linksys WiFi router, computer A (Win 7) attached by a cable to the router, computer H (Win 8.1) seen by the router via WiFi connection. I also have a Grace Digital Internet Radio via WiFi and an HP DreamScreen 100 connected via WiFi.
All of a sudden the backups of Herb stopped and I can't restart them. Even "backup now" doesn't work. I can sometimes log into the media server from Herb otehr times in tells me that I have no network connection. I have had no problem accessing the internet or getting email. When I access the Backup service on the Media server I can see both computers but H is greyed out and I can't perform any of the functions. Any ideas

It sounds like a Local Area Network (LAN) issue where you have this MediaServer installed (home, small office),
A LAN Router REBOOT may be necessary to clear .. and assign a TCP/IP address to the HP MediaSmart Server.
HP EX490 MediaSmart Server
Support Page
HP MediaSmart Server Setup Poster
Assure that your MediaServer is obtaining a TCP/IP address from your LAN Router.
You may need to login to the Router's Adminsitrative Page to check this.
This is covered in Chapter 2 of the User's Manual.
HP MediaSmart Server User Guide

MediaSmart Server v1 Reboot on Connection

Hi! Since I installed Windows 10 on one of my personnal computers (without changing anything to the server), I can't connect to my HP MediaSmart Server to administrate it. After I enter my authentification (username and password), whether it's with the console (connector), a RDP session, or from the web interface, the server reboots (health light flashing)... I tried connecting to the server from different computers and it always has that same behavior. Despite that problem, I can access the shared folders and the automatic backups of our personal computers still work. Do you have any ideas that could help solve this problem or do I have to try a server resoration with my recovery disk? Thank you

Hello johntweir,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand you are having issues connecting to your MediaSmart Server. I am sorry, but to get your issue more exposure, I would suggest posting it in the commercial forums, since this is a commercial product. You can do this at HP Enterprise Business Community - Servers.
I hope this helps. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

MediaSmart Server

My HP MediaSmart Server is unresonsive.
Power and USB Port lights are blue.
The four Light Bars are off.
There is a tapping sound coming from inside the server. It sounds like a piece of paper on the disk and taps the side with each turn.
The Health indicator light is not flashing. It's white (with a red tint).
I used a paper clip, press and release the recessed Status/Recovery button on the front of the server.
No change.
I tried the suggestions on this page: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01783366&tmp_task=solveCategory&cc=us&dlc=en&la...
I also tried forced shutdonw.
Nothing I've done so far helps.
Is there any hope in getting my documents off of this server?
Thank you

As a workaround, in the Home Server Console, under Settings > General, set the Region to English.
I find it amazing that this issue has not yet been addressed.

OSX 10.6.8 server will Not Boot

Hi my 10.6.8 server will not boot. System is a 2009 Mac pro. I have run disk utility from the original server software install disk, ran repair disk, and repair disk permissions. Get some acl found errors have read that they most often are erroneous, Still got the same errors after permission repairs. While booting in verbose mode get the following messages before it stops:
kern.maxprocoeruip: 266 -> 2400
launchctl: Couldn't stat("/library/LaunchDaemons/org.macports.asterisk.plist"): Nosuch File or directory (note: removed asterisk from this system months ago)
launchctl: Please convert the following to launchd: /ect/mach_init.d/chum.plist
launchctl: Please convert the following to launchd: /ect/mac_ini/dashboardadvisoryd.plist
launchctl: Please convert the following to launchd: /ect/mach_init.d/pilotfish.plist
Unexpected error triggering kextd volume watching.
/: Couldn't get description from Disk Arbitration..
I did read on another post here to try to reinstall the os, however when I try to install over the operating system it says I am trying to install an older os and it will not let me install in the same volume.... Although I am confident I have all the data on backups as well have timemachine backups, I would rather not have to erase and install this machine.
Any insight to this problem would be greatly appreciated.

I found that I had a bad harddrive, or at least that is what I think happened.. I did have a time machine backup as well, although in hindsight, I should have made some manual backups of my open directory and the databases hosted on the server. In any case I ended up purchasing "server grade" harddrives and reinstalling the OS on to the new blank hard drives, I was then able to recover from my time machine backup, however, I did have the issue of the restore going over 100%, I tried this several times and the same result with no end after hours and hours. After reading through various forums I found that clicking the mouse button for about 10 minutes straight once it hit 100% finally worked, I was lucky that the Time machine backup had good data on it since I have read several posts saying that Time machine doesn;t backup directoies or any "open files" very well, however I had no problems after recovering from the backup. I do however now backup or archive my directory everyday, and I rely on Filemaker to backup its own databases, however I still use time machine as well...

Server has stopped responding

Hi there, when trying to connect to the internet (Safari) I get an error message that the connection failed because the server has stopped responding. I can connect to the itunes store and the app store. I have re-started the computer, router, app, ipad and it still doesn't work. Any suggestions would be appreciated.
Thanks!

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

SAPMMC Server 0 stopped with Exit code -11113

Hi Experts ,
I am using EP 6.40 sp 12.
My SAP MMC console shows server 0 stopped with the exit code -11113.
I was tryinjg to unlock my admin password and this has happend.
Attached here is developer trace of server 0 .
trc file: "C:\usr\sap\EP3\JC00\work\dev_server0", trc level: 1, release: "640"
node name   : ID2686050
pid         : 5832
system name : EP3
system nr. : 00
started at : Wed Jun 27 13:33:35 2007
arguments   :
    arg[00] : C:\usr\sap\EP3\JC00/j2ee/os_libs/jlaunch.exe
    arg[01] : pf=C:\usr\sap\EP3\SYS\profile\EP3_JC00_ep
    arg[02] : -DSAPINFO=EP3_00_server
    arg[03] : pf=C:\usr\sap\EP3\SYS\profile\EP3_JC00_ep
[Thr 5084] Wed Jun 27 13:33:35 2007
[Thr 5084] INFO: Unknown property [box.number=EP3JC00ep]
[Thr 5084] INFO: Unknown property [system.id=0]
JStartupReadInstanceProperties: read instance properties [C:\usr\sap\EP3\JC00\j2ee\cluster\instance.properties]
-> ms host    : ep
-> ms port    : 3601
-> OS libs    : C:\usr\sap\EP3\JC00\j2ee\os_libs
-> Admin URL :
-> run mode   : NORMAL
-> run action : NONE
-> enabled    : yes
Used property files
-> files [00] : C:\usr\sap\EP3\JC00\j2ee\cluster\instance.properties
Instance properties
-> ms host    : ep
-> ms port    : 3601
-> os libs    : C:\usr\sap\EP3\JC00\j2ee\os_libs
-> admin URL :
-> run mode   : NORMAL
-> run action : NONE
-> enabled    : yes
Bootstrap nodes
-> [00] bootstrap            : C:\usr\sap\EP3\JC00\j2ee\cluster\instance.properties
-> [01] bootstrap_ID2686000 : C:\usr\sap\EP3\JC00\j2ee\cluster\instance.properties
-> [02] bootstrap_ID2686050 : C:\usr\sap\EP3\JC00\j2ee\cluster\instance.properties
Worker nodes
-> [00] ID2686000            : C:\usr\sap\EP3\JC00\j2ee\cluster\instance.properties
-> [01] ID2686050            : C:\usr\sap\EP3\JC00\j2ee\cluster\instance.properties
[Thr 5084] JLaunchRequestQueueInit: create named pipe for ipc
[Thr 5084] JLaunchRequestQueueInit: create pipe listener thread
[Thr 3472] JLaunchRequestFunc: Thread 3472 started as listener thread for np messages.
[Thr 2644] WaitSyncSemThread: Thread 2644 started as semaphore monitor thread.
[Thr 5084] NiInit2: NI already initialized; param 'maxHandles' ignored
[Thr 5084] INFO: Unknown property [JLaunchParameters=]
[Thr 5084] *** WARNING => Maximum Java heap size specified twice (through maxHeapSize and in javaParameters) - using -Xmx1024M [jstartxx.c   2300]
[Thr 5084] [Node: server0] java home is set by profile parameter
     Java Home: C:\j2sdk1.4.2_12
JStartupIReadSection: read node properties [ID2686050]
-> node name       : server0
-> node type       : server
-> java path       : C:\j2sdk1.4.2_12
-> java parameters : -Djava.security.policy=./java.policy -Djava.security.egd=file:/dev/urandom -Dorg.omg.CORBA.ORBClass=com.sap.engine.system.ORBProxy -Dorg.omg.CORBA.ORBSingletonClass=com.sap.engine.system.ORBSingletonProxy -Djavax.rmi.CORBA.PortableRemoteObjectClass=com.sap.engine.system.PortableRemoteObjectProxy -Djco.jarm=1 -Dsun.io.useCanonCaches=false -Djava.awt.headless=true -XX:SoftRefLRUPolicyMSPerMB=1 -verbose:gc -XX:PrintGCDetails -XX:PrintGCTimeStamps -XX:UseParNewGC -XX:MaxNewSize=85M -XX:NewSize=85M -XX:DisableExplicitGC -XX:MaxPermSize=192M -XX:PermSize=192M -XX:SurvivorRatio=2 -XX:TargetSurvivorRatio=90 -Drdbms.driverLocation=C:/oracle/EP3/ora92/jdbc/lib/classes12.jar -Dsys.global.dir=C:/usr/sap/EP3/SYS/global/
-> java vm version : 1.4.2_12-b03
-> java vm vendor : Java HotSpot(TM) Server VM (Sun Microsystems Inc.)
-> java vm type    : server
-> java vm cpu     : x86
-> heap size       : 1024M
-> init heap size : 1024M
-> root path       : C:\usr\sap\EP3\JC00\j2ee\cluster\server0
-> class path      : .\bin\boot\boot.jar;.\bin\boot\jaas.jar;.\bin\system\bytecode.jar;.
-> OS libs path    : C:\usr\sap\EP3\JC00\j2ee\os_libs
-> main class      : com.sap.engine.boot.Start
-> framework class : com.sap.bc.proj.jstartup.JStartupFramework
-> registr. class : com.sap.bc.proj.jstartup.JStartupNatives
-> framework path : C:\usr\sap\EP3\JC00\j2ee\os_libs\jstartup.jar
-> shutdown class : com.sap.engine.boot.Start
-> parameters      :
-> debuggable      : no
-> debug mode      : no
-> debug port      : 50021
-> shutdown timeout: 120000
[Thr 5084] JLaunchISetDebugMode: set debug mode [no]
[Thr 3444] JLaunchIStartFunc: Thread 3444 started as Java VM thread.
JHVM_LoadJavaVM: VM Arguments of node [server0]
-> stack   : 262144 Bytes
-> arg[ 0]: exit
-> arg[ 1]: abort
-> arg[ 2]: -Djava.security.policy=./java.policy
-> arg[ 3]: -Djava.security.egd=file:/dev/urandom
-> arg[ 4]: -Dorg.omg.CORBA.ORBClass=com.sap.engine.system.ORBProxy
-> arg[ 5]: -Dorg.omg.CORBA.ORBSingletonClass=com.sap.engine.system.ORBSingletonProxy
-> arg[ 6]: -Djavax.rmi.CORBA.PortableRemoteObjectClass=com.sap.engine.system.PortableRemoteObjectProxy
-> arg[ 7]: -Djco.jarm=1
-> arg[ 8]: -Dsun.io.useCanonCaches=false
-> arg[ 9]: -Djava.awt.headless=true
-> arg[ 10]: -XX:SoftRefLRUPolicyMSPerMB=1
-> arg[ 11]: -verbose:gc
-> arg[ 12]: -XX:+PrintGCDetails
-> arg[ 13]: -XX:+PrintGCTimeStamps
-> arg[ 14]: -XX:+UseParNewGC
-> arg[ 15]: -XX:MaxNewSize=85M
-> arg[ 16]: -XX:NewSize=85M
-> arg[ 17]: -XX:+DisableExplicitGC
-> arg[ 18]: -XX:MaxPermSize=192M
-> arg[ 19]: -XX:PermSize=192M
-> arg[ 20]: -XX:SurvivorRatio=2
-> arg[ 21]: -XX:TargetSurvivorRatio=90
-> arg[ 22]: -Drdbms.driverLocation=C:/oracle/EP3/ora92/jdbc/lib/classes12.jar
-> arg[ 23]: -Dsys.global.dir=C:/usr/sap/EP3/SYS/global/
-> arg[ 24]: -Dsys.global.dir=C:\usr\sap\EP3\SYS\global
-> arg[ 25]: -Dapplication.home=C:\usr\sap\EP3\JC00\j2ee\os_libs
-> arg[ 26]: -Djava.class.path=C:\usr\sap\EP3\JC00\j2ee\os_libs\jstartup.jar;.\bin\boot\boot.jar;.\bin\boot\jaas.jar;.\bin\system\bytecode.jar;.
-> arg[ 27]: -Djava.library.path=C:\j2sdk1.4.2_12\jre\bin\server;C:\j2sdk1.4.2_12\jre\bin;C:\j2sdk1.4.2_12\bin;C:\usr\sap\EP3\JC00\j2ee\os_libs;C:\oracle\EP3\ora92\bin;C:\Program Files\Oracle\jre\1.3.1\bin;C:\Program Files\Oracle\jre\1.1.8\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\j2sdk1.4.2_12\bin;C:\usr\sap\EP3\SCS01\exe;C:\usr\sap\EP3\JC00\exe;C:\usr\sap\EP3\SYS\exe\run
-> arg[ 28]: -Dmemory.manager=1024M
-> arg[ 29]: -Xmx1024M
-> arg[ 30]: -Xms1024M
-> arg[ 31]: -DLoadBalanceRestricted=no
-> arg[ 32]: -Djstartup.mode=JCONTROL
-> arg[ 33]: -Djstartup.ownProcessId=5832
-> arg[ 34]: -Djstartup.ownHardwareId=W1703069195
-> arg[ 35]: -Djstartup.whoami=server
-> arg[ 36]: -Djstartup.debuggable=no
-> arg[ 37]: -DSAPINFO=EP3_00_server
-> arg[ 38]: -DSAPSTARTUP=1
-> arg[ 39]: -DSAPSYSTEM=00
-> arg[ 40]: -DSAPSYSTEMNAME=EP3
-> arg[ 41]: -DSAPMYNAME=ep_EP3_00
-> arg[ 42]: -DSAPDBHOST=
-> arg[ 43]: -Dj2ee.dbhost=ep
[Thr 3444] JHVM_LoadJavaVM: Java VM created OK.
JHVM_BuildArgumentList: main method arguments of node [server0]
[Thr 5952] Wed Jun 27 13:33:37 2007
[Thr 5952] JHVM_RegisterNatives: registering methods in com.sap.bc.proj.jstartup.JStartupFramework
[Thr 5952] JLaunchISetClusterId: set cluster id 2686050
[Thr 5952] Wed Jun 27 13:33:38 2007
[Thr 5952] JLaunchISetState: change state from [Initial (0)] to [Waiting for start (1)]
[Thr 5952] JLaunchISetState: change state from [Waiting for start (1)] to [Starting (2)]
[Thr 4888] Wed Jun 27 13:33:44 2007
[Thr 4888] JHVM_RegisterNatives: registering methods in com.sap.security.core.server.vsi.service.jni.VirusScanInterface
[Thr 4820] Wed Jun 27 13:33:58 2007
[Thr 4820] JLaunchIExitJava: exit hook is called (rc=-11113)
[Thr 4820] JLaunchCloseProgram: good bye (exitcode=-11113)
Can you guys help me ?
Regards,
Ashish Shah

Hi Ashish,
Plz unlock your admin; using below steps:
Just follow below steps:
STEP-1:
1.Start the Config Tool C:\usr\sap\<SID>\<engine-instance>\j2ee\configtool\configtool.bat
Ex: D:\usr\sap\F02\JC00\j2ee\configtool --> configtool.bat
2. "Switch to configuration mode" for that Click on "Pencil" icon;
3. Click on "Pencil" icon means "Swith to Configuration Edit mode" then say "YES"
4. cluster_data --> server --> cfg --> services -->
click on "Propertysheet com.sap.security.core.ume.service
select properties:
ume.superadmin.activated = True
ume.superadmin.password = <enter password >
then say "OK"
Click on "Pencial ICON.
5. Save & restart Java Engine.
STEP-2: Logon with SAP*
Login with "SAP*" into portal
1. http://<host>:<Port>/useradmin/index.jsp
2. Enter userid / password as" SAP* / <password ex: abc123>"
3. Search for "Administrator" user
4. Reset or change password for "Administrtor"
STEP-3: Disable "SAP*"
1.Start the Config Tool C:\usr\sap\<SID>\<engine-instance>\j2ee\configtool\configtool.bat
Ex: D:\usr\sap\F02\JC00\j2ee\configtool --> configtool.bat
2. "Switch to configuration mode" for that Click on "Pencil" icon;
3. Click on "Pencil" icon means "Swith to Configuration Edit mode" then say "YES"
4. cluster_data --> server --> cfg --> services -->
click on "Propertysheet com.sap.security.core.ume.service
select properties:
ume.superadmin.activated = False
ume.superadmin.password = <enter password >   --> delete password of SAP*
then say "OK"
Click on "Pencial ICON.
5. Save & restart Java Engine.
STEP-4: Login with "Administrator"
1. http://<host>:<Port>/useradmin/index.jsp
2. Enter userid / Password as "Administrator / <password>
3. it will ask change password just change it.
Please follow steps one by one. it should resolve your issue.
Thanks,
Nagaraju

HP MediaSmart Server EX485 keeps restarting

I have a HP MediaSmart Server EX485 and it keeps rebooting. If I shut it off for awhile it boots up normal. Is this a powersuppy issue, or a overheating Issue?

Hi Shatterglass,
Your HP MediaSmart Server EX485 is a commercial product and to get your issue more exposure I would suggest posting in the commercial forums. Here is a link to the Commercial Notebook forum.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Question about HP MediaSmart Server and Time Machine

I just got an EX490 MediaSmart server to use for backups and as a media server. I set up the server to serve as a Time Machine backup device, and it seems to work fine. However, when the server is connected and appears as a Share in the Finder, if I use the Finder to navigate to the "Mac" folder on the server, I don't see any files inside. Actually I searched through all visible files on the server and didn't see any files that might be a backup file. I tried turning on Invisible file viewing but that didn't make any difference. I'm assuming that the Time Machine backup file on the server is somehow hidden from viewing.
Does anyone know why the backup file isn't appearing?
Thanks.

I have been looking at similiar HP NAS model, which now appears to have beome a prior model -
HP EX485 MediaSmart Home Server
http://www.amazon.com/gp/product/B001OI2ZG4/
The prices have gone up slightly, too. The reviews on the above EX485 were almost like a mini review and informative. I assume you've created accounts and perhaps have (need?) a PC to configure Windows Home Server R2 fully? I was waiting for full Windows 7 support which is still in beta.
From what I read, one of the "Missing Bible" for WHS or something helps to get the most out of it and help with setup (though generally that just takes 15 minutes if you know how).

Mediasmart server EX495 Blank Contents screen

Ofr the last week or so, I can not get the content screen to show after connecting from any of my clients. I getthe password screen when I try to get to the console. then the progress screen appears. But then instead of the console screen I get the background screen only no matter how long I leave it be. It never goes beyond that.
At the same time, using any of the MS Office applications to load an office document from the shared folders on the server freezes the applicaton. Even Outlook 2007 freezes just opening it (I have Outlook email to the shared folders on the server).
The only remedy I can find is to manually reboot the server which resolves the problem for about 30 minutes then it all happens over again. This full problem started this morning. Oh yes, all the lights on teh server indicate a go status. And when I reboot the server and can get into the console, everything is in order.
I just bought this one when me original Mediasmart server EX470 with the original WHS software w/PP2 finally crashed and I could not revive it (RIP).
Anyne else having a similar problem?

I wanted to provide an update. Spotify 1.0.1.1060.gc75ebdfd appears to have changed behavior. HTTP proxy support appears to be removed now (I can't even play music using my previous prefs). I can enable my HTTPS proxy by editing the prefs file as before. I should be able to do this now through Spotify's settings, but it looks like there's a bug in the settings panel where it seems to require a username and password before saving (my proxy doesn't require a username and password). This time, change the @http back to @https. Here's how my proxy settings now look under 1.0.1.1060.gc75ebdfd:
network.proxy.addr="proxyout.xxx.xxx:8080@https"
network.proxy.mode=2
This allows me to play music and view most images. The only remaining problem is that now I'm still seeing instances where album art and other images aren't downloaded. It's not as prevalent as before, but I do see it when browsing, for example, the News tab under Browse.

TX2517ca, wont Boot - Blinking blue LED lights - Num Lock & Caps Lock

notebook just decided NOT to boot one day..I can hear the fan and very minimal HDD activity. I've tried the Hard reset as directed by HP and removed the battery etc... the lights blink exactly the same time, stay on for 1 sec, and the off for 3 seconds and then blink simultaneously again, and doesn't stop till I pull the power, there is no clicking, grinding, beeping nothing, nothing on the screen at all. The rest of the lighted buttons are solid blue.
FYI, I am a computer technician of 15 years...home based at this time. so I have pulled the memory, cleaned them, 2 (1GB & 2Gb), compress air dried them and blue out the slots and reseated even by doing only 1 at a time, no change, same end result, blinking LED's. So I just pulled the Hard drive, connected it to another machine as an external HDD, it works fine, I can see the C drive and the Recovery drive without any problems. so at this point I have just pulled the battery from the board and will leave for a while to see if we can drain the BIOS/CMOS (wondering if software is stuck in hibernate or sleep and when powering on is only returning to similiar state, but wouldn't account for no screen display...) everything so far is pointing to CPU I would think. Next after replacing existing Hard drive and try booting if that doesn't work, I have a working blank Hard drive I can insert to try for the hell of it...stay tuned...
Oh, also system is immaculate, no collected hair or dust in fan ports etc..
This question was solved.
View Solution.

Hi,
Check the link below:
Blank Screen LED Error Codes
** Say thanks by clicking the "Thumb up" icon which is on the left. **
** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

I've only had my iphone 5s for a week. I keep getting an error message of "Server has stopped responding." I need the server to work. Does anyone know if there is a "fix" for the problem? Other wise, I probably best return for a refund and get a Samsung.

I've only had my iphone 5s for a week. I keep getting an error message of "Server has stopped responding." I need the server to work. Does anyone know if there is a "fix" for the problem? Other wise, I probably best return for a refund and get a Samsung. Thanks

sandyzotz wrote:
Other wise, I probably best return for a refund and get a Samsung.
Unlikely. Based on the complete lack of detail of the issue provided it is entirely possible the same issue would occur.
Unless and until the user provides some actual details of the problem, there is nothing the indicate that the issue is with the iPhone.

HP Mediasmart Server EX490 stopped booting; health light blinks blue forever

Similar Messages

Maybe you are looking for