HP Pavilion 500 (desktop) will not boot after updating driver's.

Working on my mothers CPU but I cant seem to get past this screen now
This was after I had downloaded and installed drivers from this site. I cant seem to figure out why it is not going in to windows xp. Any ideas? It also was giving me a fan error which was easy to fix but cant seem to figure this out.

wow no one can help I guess everyone is duped as I am. DaRN HP

Similar Messages

  • HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

    After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing. 
    I have tried a "hard reset" a number of times with no success. 
    When the battery is present the white LED flashes 3 times when the power button is pressed. 
    Please please help. 

    Hello Cuffy,
    Welcome to the HP Forums!
    I understand you notebook will not boot after a series of Windows updates.
    Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
    If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
    You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
    You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
    Hopefully this information helps!
    Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
    Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
    The Great Deku Tree
    I work on behalf of HP.

  • Will not boot after updates

    I have a macbook air. It is running Lion. After updates it will not boot. It starts installing updates and just stops all together. Any help would be very welcome.

    Hey bfa67,
    Thanks for the question. To isolate the issue, what happens when you start up in Safe Mode?:
    OS X: What is Safe Boot, Safe Mode?
    http://support.apple.com/kb/HT1564
    Thanks,
    Matt M.

  • IMac, 2010, will not boot after update

    After downloading Yosemite, my 2010, 27" iMac will not reboot. It appeared to install ok but it stayed white screen, no text for more than an hour after it automatically rebooted. Idaes? 

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
    a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.  
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • Pavilion dv5020ca sound will not work after updating xp to vista home premium

    HP Pavilion Dv5020ca   windows vista home premium
    After upgrading from xp to vista the drivers for my sound card will not install and the error message i recieved was
    cannot find media any help would be apperciated
    This question was solved.
    View Solution.

    Hi:
    See if installing the XP audio driver works...
    Download and run this driver.  If it automatically installs the audio, great.  If not...close out of any error windows.
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-42513-1&cc=us&dlc=en&lc=en&...
    Go to the device manager and click on the multimedia audio controller needing drivers.
    Click on the driver tab.  Click on update driver.  Select the Browse my computer for driver software option and at the bottom of that window, select the Let me pick from a list of device drivers on my computer.
    The select Have Disk and browse to: C:\SWSetup\sp33443\CPL30A5a and select the Conexant High Definition Audio from the list and see if the driver installs.
    Then reboot.

  • Macbook Will Not Boot After Updating Leopard

    I just reinstalled Leopard after having some trouble with my partition tables, and everything ran smoothly and worked fine. After the install I let software update update everything including the 10.5.5 update. It prompted me to reboot, and when I did it got to the grey Apple screen and the thing spun for about 30 seconds before it restarted and did it again. This happened a few times and then I booted from a Leopard disk to look at disk permissions and they seem to be fine. Anyone have any idea why this is happening or how I would fix it?
    Thanks in advance, hope to get this sorted out quickly, I thought I had finally gotten my computer working fine again when I reinstalled Leopard. :P

    At start up, press 'C' to boot directly from a CD/DVD. Or, you can press 'Option' and you should get a list of bootable selections (CD/DVD, external hardrives) that you can boot from - assuming you have something that IS bootable.
    I recently had a problem and ended up reinstalling my OS (via TimeMachine). I also confirmed that you can boot from your original OSX install disk. As part of this process I also discovered I could NOT boot directly FROM the AppleCare provided TechTools Deluxe disk. Supposedly you can boot INTO that disk via a restart but that seems kind of silly to me.
    However, if you have signed up for AppleCare and go to the Apple Support web site, you can download TechTools Deluxe and it can be made bootable by burning the .dmg file via Apple Disk Utilities. I don't understand Apple logic of not making the provided AppleCare TechTools Deluxe disk bootable.

  • Server will not boot after update !! Help needed fast !!

    I have a new (Aug 2005) XServe G5, running 4.3.
    Active Directory integrated, stores home folders (AFP), manages preferences and 5 print queues for 55 Mac OS X.4.3 clients and 200 users.
    It downloaded the 4.4 update, unchecked the OS 4.4 update (I think was my first mistake), restarted. Now, at boot up, about the moment the apple would appear (maybe it appears for a split second) all I get is the ugly not sign.
    -- Am able to boot to external firewire drive
    -- Drive shows as boot option
    -- Disk repair reported no problems to fix
    -- Can not find any log entries after last shut down. No service ever starts for any entries to be made.
    -- Applied the 4.4 update successfully while booted from external fw drive, no effect. Startup disk reports system to be OS X Server 4.4 and lists as a boot option.
    -- Drive behaves same when transferred to my G5 tower: big not sign.
    What other steps can I do to troubleshoot this boot problem? If I don't get this server up this weekend, I'll get roasted by an angry mob.
    Any suggestions are welcomed and greatly appreciated.

    Eeh...
    Always clone the existing system prior to updating it. Do so when the server is not in use, shut off services where possible (you want it to be as quiescent as possible).
    Mike Bombich (at Apple) describes how you can do this via the command-line, which I prefer for this purpose (you can stagger the process):
    http://www.bombich.com/mactips/image.html
    Now then:
    Have you booted from the install CD and used Disk Utility to run Repair Permissions ? That should be your first step.
    It may change nothing, but can you boot into Safe mode ? Hold down the Shift key at powerup and keep holding it until you see: "Safe boot"
    If you CAN get it booted in that state, then run the 10.4.4 COMBO updater
    you need to run the combo updater at this point. After doing so, use Disk Utility to run repair permissions on the boot drive itself, and then reboot.
    Otherwise, start it in Target Disk Mode as you did before, connect it to a unit running 10.4.4, and run the /combo/ 10.4.4 Server updator (NOT client, of course) onto the server's mounted hard drive.
    I'm not sure you can do this while running 10.4.x client. You may need to do a quick install of 10.4 server (say onto a Firewire drive), boot your spare Mac from it, and -then- mount the server via Firewire target mode, and apply the 10.4.4 server combo updater.
    Good luck !

  • Z68 WIN 7 will not boot after setting drive BIOS from IDE to SATA

    MSI Z68MA-ED55 (B3) Motherboard
    Windows 7 Ultimate 64 bit OS
    SATA III Solid State Drive with greater than 500 MB/s throughput
    After installing WIN7 and all my Applications programs I noticed in the BIOS that the driver for the SSD did not properly set to fully support the SSD but remained in the IDE mode.
    This computer was built for technical graphics work and not for child's play.  So I don't want to have to reinstall all the applications software for work with all its required protection features from theft.
    QUESTIONS:
    1. With this high transfer rate SSD, is it worth the performance improvement to reset the BIOS from the IDE driver to the proper driver?
    2. If so, how can I set the BIOS to the correct driver without reinstalling everything?
    3. At some level of the installation the system should have sensed the SSD SATA III and changed the driver from IDE. Where should this take place?

    Hi,
    I had the same problem. You need to put it back to IDE, boot to Windows then follow the below instructions and it works fine. (Courtesy of Guru3D)
    Enable AHCI
    The last tip we want to give you to gain a little extra performance boost is that you enable AHCI mode. AHCI mode can help out greatly in performance for SSDs. Now, if you swap out an HDD for an SSD with the operating system cloned and THEN enable AHCI in the BIOS, then you'll likely get a boot error / BSOD.
    The common question is, is there a solution for this ?
    To answer that question (and as we do safely with all modern chipsets) there is a way to safely enable AHCI mode. Here we go:
    1. Startup "Regedit"
    2. Open HKEY_LOCAL_MACHINE / SYSTEM / CurrentControlset / Services
    3. Open msahci
    4. In the right field left click on "start" and go to Modify
    5. In the value Data field enter "0" and click "ok"
    6. exit "Regedit"
    7. Reboot Rig and enter BIOS (typically hold "Delete" key while Booting)
    In your BIOS select "Integrated Peripherals" and OnChip PATA/SATA Devices. Now change SATA Mode from IDE to AHCI.
    You now boot into windows 7 or Vista, and the OS will recognize AHCI and install the devices. Now the system needs one more reboot and voilla ... enjoy the improved SSD performance.

  • [SOLVED] Kernel will not boot after update to 3.1.5

    Not sure what went wrong here. Pacman seemed to hang when updating, so I CTRL-C'd it and restarted the upgrade. It seemed to complete properly. That was a few hours ago and I did not immediately reboot the computer but went on with my work instead. After rebooting the laptop I get this
    ***normal boot up to this :
    Running Hook [uresume]
    resume libgcrypt version: 1.5.0
    resume: Could not stat the resume device file '/dev/sda4'
    Please type in the full path name to try again or press ENTER to boot the system: _
    Pressing ENTER at this point results in mean looking error message :
    ERROR : Unable to determine major/minor number of root device '/dev/sda4'
    You are being dropped to a recovery shell
    Type 'exit' to try and continue booting
    sh: can't access tty: job control turned off
    [ramfs /]# _
    **typing exit**
    Trying to continue (this will most likely fail)...
    mount: you must specify the filesystem type
    You are being dropped into an emergency shell
    sh: can't access tty: job control turned off
    [ramfs /]# _
    Did I somehow ruin my install or is there something I can do?
    EDIT : Oh and it can still boot the windows partition, so it's not likely due to defective hardware.
    Last edited by bolshevik (2011-12-16 14:31:19)

    bolshevik wrote:
    Not sure what went wrong here. Pacman seemed to hang when updating, so I CTRL-C'd it and restarted the upgrade. It seemed to complete properly. That was a few hours ago and I did not immediately reboot the computer but went on with my work instead. After rebooting the laptop I get this
    ***normal boot up to this :
    Running Hook [uresume]
    resume libgcrypt version: 1.5.0
    resume: Could not stat the resume device file '/dev/sda4'
    Please type in the full path name to try again or press ENTER to boot the system: _
    Pressing ENTER at this point results in mean looking error message :
    ERROR : Unable to determine major/minor number of root device '/dev/sda4'
    You are being dropped to a recovery shell
    Type 'exit' to try and continue booting
    sh: can't access tty: job control turned off
    [ramfs /]# _
    **typing exit**
    Trying to continue (this will most likely fail)...
    mount: you must specify the filesystem type
    You are being dropped into an emergency shell
    sh: can't access tty: job control turned off
    [ramfs /]# _
    Did I somehow ruin my install or is there something I can do?
    EDIT : Oh and it can still boot the windows partition, so it's not likely due to defective hardware.
    If you foolishly interrupted the initramfs creation after a kernel upgrade and didn't regenerate it manually, you earned this.
    You'll need to find a live CD so you can chroot to your install and rerun mkinitcpio.

  • Macbook (Black) Will Not Boot After Update (grey screen of non-booting)

    I bought my first MacBook less than one month ago.
    Last night at 9pm the apple update software said there was an update and I should restart. It has not been able to boot since.
    Now, when the computer turns on it shows a grey screen with a dark grey apple logo for a few minutes, then turns off again.
    I am completely lost, any help would be greatly appreciated.
    Thank you for your time.
    Chris Albon

    Sorry to hear about your troubles Chris.
    Was this a System/Security update you installed or just for an application? Personally, I never install anything system related without first running a 3rd party Disk Utility like DiskWarrior. It's important to ensure that there are no latent issues before doing so. That being said, if you don't have access to DW, try booting up from your OSX installation DVD (insert the disk and hold down the 'C' key on startup) and choose Disk Utility's disk repair option from the file menu once it's loaded. Post back once you've tried this.

  • Mac Mini will not boot after Security Update 2008-007

    Hello,
    A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
    Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

    Hi Arkku , and a warm welcome to the forums!
    I'd certainly give Sig's advice a try first.
    If that should fail...
    applesetupdone...
    This was Posted by: JoseAranda at September 9, 2006 3:48 AM
    "OK, restart your computer, hold down Command-s and type in the following:
    /sbin/fsck -fy Enter
    /sbin/mount -uaw Enter
    rm /var/db/.applesetupdone Enter
    # The rm command is the remove command which deletes the file.
    # Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
    reboot Enter
    Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
    end of posted by: JoseAranda"
    Reset OS X Password Without an OS X CD...
    http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

  • MacBook Pro will not boot after software update

    MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you).  MONEY, MONEY, MONEY is the name of the game.  They can cause your computer to crash and still charge you! 
    Does anyone have an answer to why my computer is showing a little gear spinning for hours?  I have tried several things with NO luck.
    Thanks-

    Run through the list of fixes here
    Step by Step to fix your Mac

  • HT4623 iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

    iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

    Obviously since you have iOS 7 you're a developer.  As a developer, you signed a NDA with Apple not to discuss the iOS on a public forum.  Please log in to the Developer Forum using your credentials and ask for help there, lest you risk having your credentials terminated.
    Thanks, and best of luck to you.
    GDG

  • HP m9300t desktop will not boot

    Hoping someone can help me out here.  I think my motherboard is shot but would appreciate some second opinions.  My HP m9300t desktop will not boot past the initial "HP Invent" blue splash screen.  On this screen, I have the options to enter Setup, Boot Menu, Recovery, or Diagnostics.  Normally, this screen will display for a few seconds then the PC will start to boot into Windows but that's not happening anymore.  Instead, it just hangs on the "HP Invent" screen.  If I attempt to enter Boot Menu, Recovery, or Diagnostics, nothing happens.  If I attempt to enter Setup, it will display a message saying "entering Setup" but the computer just hangs there and never does enter Setup.  I hear my fans spinning, I *think* I hear at least one of the hard drives spin up (I have two in the system), the blu-ray drive activity light blinks as it normally does when I turn the system on, but again, system will not boot past the HP splash screen.  I have tried booting from the Windows cd (no luck) as well as attempted to boot with all peripherals disconnected except keyboard and mouse and again, no luck.  I have noticed that the past two days the system has behaved somewhat erratically, locking up two times requiring a reboot but I just chalked that up to general Windows instability and/or my installing of some new beta software for a HDHomeRun cablecard tuner I just installed.  Looking back though, maybe those were some warning signs that my motherboard was on the brink of dying.  In any case, what I am thinking now is that the motherboard needs to be replaced but before I go out and buy a new one, I wanted to get other people's opinions in case I am overlooking something.  Thanks for any help that you can offer.

    Marty, welcome to the forum.
    Since the computer is over 3 years old, I believe that you have a failed power supply unit (PSU).  Here is a guide to help you troubleshoot the problem.
    Please click "Accept as Solution" if your problem is solved.
    Signature:
    HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
    HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
    HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
    HP Photosmart 7520 AIO
    ++++++++++++++++++
    **Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
    Intelligence is God given; Wisdom is the sum of our mistakes!
    I am not an HP employee.

  • MBP 17" will not restart after updating Java... why?

    MBP 17" will not restart after updating Java...why?
    It would actually try to restart for about 10-15 seconds but would quit and then shut down. Tried using P_R_Command_Options but that too failed and again it just shut down. Tried using D at startup which ran a test of the hard drive. No issues there which tells me there's a software problem.
    Can any one help?

    Disk Utility suggest reformating
    Reformatting is not a Recovery Aid. When Disk Utility suggests reformatting, it is because it considers your drive unsalvageable. Yes, you lose all the data on the drive when you reformat.
    And yes, Mac OS X Extended, journaled is the method you will need for a Mac OS X Boot drive.
    You should also consider buying a replacement drive to have on hand the next time this internal drive gives you the slightest bit of trouble. Possibly an external enclosure to put it in as well. and it would not hurt to go ahead and Install Mac OS X on it and try booting from it, to make sure it is ready.
    And make sure your Backups are current, as the next time that internal drive screws up you may get no warning whatsoever.

Maybe you are looking for