HT1338 My mac mini will not allow me to update itunes with osx mountain lion 10.5. I check for software updates and it says none.

what shall' I do?

10.5 is not Mountain Lion. You need to find out what release of OS X is on your Mac. Go to >About This Mac and tell me what you see.

Similar Messages

  • HT1338 My I pad will not allow me to update

    My I pad will now allow me to update?

    Connect to iTune and Check for Update (tap to enlarge image)

  • Mac Mini will not boot after Security Update 2008-007

    Hello,
    A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
    Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

    Hi Arkku , and a warm welcome to the forums!
    I'd certainly give Sig's advice a try first.
    If that should fail...
    applesetupdone...
    This was Posted by: JoseAranda at September 9, 2006 3:48 AM
    "OK, restart your computer, hold down Command-s and type in the following:
    /sbin/fsck -fy Enter
    /sbin/mount -uaw Enter
    rm /var/db/.applesetupdone Enter
    # The rm command is the remove command which deletes the file.
    # Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
    reboot Enter
    Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
    end of posted by: JoseAranda"
    Reset OS X Password Without an OS X CD...
    http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

  • Mac Mini will not load after recent update.

    My late 2012 model Mac Mini just had a software update and upon rebooting, my login name did not populate.  I rebooted again and now I get the gray screen with spinner and progress bar.  Once the progress bar loads I have just the spinner for a minute or so before it cuts off completely.  I use a wireless MAC keyboard and it will not load into safe mode when I try holding down SHIFT upon reboot.  Any suggestions?

    Try Safe Mode with a wired KB
    Use a PC KB if necessary
    http://support.microsoft.com/kb/970299
    Boot to recovery
    OS X: About OS X Recovery
    and try repairing the startup disk
    Next reinstall the OS

  • MAC Mini does not restart after Yosemite update

    I bought my MAC mini in 2011 and I successfully updated to Mavericks with no problems.  I am not sure why my MAC Mini will not restart after I updated to Yosemite. The completion bar gets stuck around 30%.
    Any help or ideas appreciated 
    Larry

    Okay, this is strange.  I tried restarting three times yesterday with the same results. In fact I left it go overnight only to find the next morning that the bar was still stuck at 30%.  I did a hard boot a little bit ago and waited a few seconds. I restarted an it booted up fine.
    Larry

  • Aperture 3.1 will not allow me to update

    Aperture 3.1 will not allow me to update.

    Hi, It says I need Aperture 3. which i already have. 10.6.7 is my current OS. I downloaded it from the APP Store a few months ago. I am presently using Aperture 3.1.1 I have read in forums that the problem could be some leftover file from the trial version.. which I never used, so that preference file is not there. I am trying to update to 3.0.2 and eventually to 3.0.3
    Ahy help would be appreciated.

  • My mac mini will not let me log in.   it says i can change my login info with my apple id.   no good!   help desk stumped!   Help!

    my new Mac Mini will not let me log in.   I shut it down while away on vacation and now it will not accept my password.   I tried to log in with my apple ID and it still would not accept it.   I stumped the apple help desk.   Help!

    User Password Reset

  • My mac mini will not shutdown with either Mavericks or Yosemite (following a clean install)

    First noted while running Mavericks, my Mac-Mini will not shutdown.  It just hangs on a black screen with the little icon.  I created a clean user account and the problem went away.  Rather than do a fresh install of Mavericks, I waited until Yosemite came out.  I reformatted the drive and did a fresh Yosemite install.  I then restored my apps and data only to find the problem is still present.  I've also tried stopping many of the applications I would normally expect might cause the problem with no luck.  And I tried the one Yosemite suggestion regarding deleting the Library/Caches folder content with no luck.
    My naive question:  following the fresh install of Mavericks, should I have done a re-install of my (very many) applications instead of a restore from an image?
    I've tried looking at the system logs after I've forced a shutdown with the power button but there's nothing I could find that shows any problems.
    Any other suggestions of things to try would be appreciated.

    Hi,
    Thanks.
    It is running 10.5.8.
    I am trying to boot up an external drive with 10.5.8 on it. It works on my Macbook Pro which is running 10.5.8, runs on my IMAC running SL. But doesnt work on the mac mini?
    It had been running SL, however there are a number of programs I have like Windows Live Sync which are not yet compatable with SL so i downgraded to 10.5.6 which came with the Mac Mini then loaded all updates.
    It seems to just go into an auto reboot as soon as i click on it.
    i thought it might be the firmware? Is it possible to downgrade them and then re-install?
    I have reset the PRAM.
    Any help would be appreciated.
    Thanks

  • Help, my Mac mini will not start up, only keeps thinking on first page( white screen with apple emblem)

    Help, my Mac mini will not start properly. Only goes to the white screen with thinking. Will not go to the password section

    Are you sure about your hard disk health, any clicking noice recently?
    Go to boot menu (press option button or button left to your space bar while booting) > Select Recovery drive > Disk utility > Verify the volume on which OS X is installed.

  • My Mac Mini will not read TDK disks from my iMac G3.

    My Mac Mini will not read TDK disks from my iMac G3.
    I used an iMac G3 (2001) -- the ones that looked like a big pod -- running on OS X and saved files to TDK  CD-R, 700 MB disks, which worked fine. Now that I have a Mac Mini (model number  A1347) I cannot get this computer to read those disks, made on the iMac G3.  Once inserted each disk will open and I can retrieve files for a short period, then the problems start. The computer makes some noises, the beach-ball/pinwheel goes around and I cannot get the files to open or the disk to eject. After a while the disk does eject -- to my relief. I keep using Control+E until ejection happens.
    My Mac Mini (2010-2011) is hooked up to a View Sonic HDMI LED monitor, an iOmega external hard-drive for backing up, an Epson Stylus C88 Plus printer and to the internet by a fibre 10MB feed. The Mac Mini runs on OS X version 10.6.8 Snow Leopard: Processor Speed:2.66 GHz
    I took the Mac Mini to an Apple retailer and he hooked the computer up to one of his monitors and it read the TDK disks just fine. I am now using Sony CD-RW, 700 MB disks, but I would prefer to use my TDKs because I have such a large pile of blank ones to use and there are those TDK disks with information that I want to look at from time to time. Can anyone tell me what to do?
    DJG

    Try disconnecting everything attached to the Mini except the monitor.
    If that doesn't work, try setting up another admin user account to see if the same problem continues. If Back-to-My Mac is selected in System Preferences, the Guest account will not work. The intent is to see if it is specific to one account or a system wide problem. This account can be deleted later. If successful, copy the files to the original account Public/Dropbox.
    Isolating an issue by using another user account
    If the problem is still there, try booting into the Safe Mode using your normal account.  Disconnect all peripherals except those needed for the test. Shut down the computer and then power it back up after waiting 10 seconds. Immediately after hearing the startup chime, hold down the shift key and continue to hold it until the gray Apple icon and a progress bar appear. The boot up is significantly slower than normal. This will reset some caches, forces a directory check, and disables all startup and login items, among other things. When you reboot normally, the initial reboot may be slower than normal. If the system operates normally, there may be 3rd party applications which are causing a problem. Try deleting/disabling the third party applications after a restart by using the application un-installer. For each disable/delete, you will need to restart if you don't do them all at once.
    Safe Mode - About
                    Safe Mode

  • Hello, mac mini will not boot. I get a file symbol with a question mark, then a white screen, Hello, mac mini will not boot. I get a file symbol with a question mark, then a white screen

    Hello, My mac mini will not boot. When I turn it on, I get the chime, then the white screen, then the apple symbol, then a file symbol with a question mark, then the white screen and then it stays like that.
    Is this a bad hard drive?

    Sounds like it.  Try booting from your OSX restore DVDs - startup and hold down "C".  This will take AGES! Then run Disk Utility from the menu. 
    The flashing ? means your system is corrupt, dead, not there, on a dying HD, etc...

  • Iphoto on my used mac mini will not open my photos from my new macbook air, it says to update software but there arent any available.. please help

    iphoto on my used mac mini will not open my photos from my new macbook air,  it says something about updating the software, but i checked and there arent any updates available... please help

    Sorry for the second post..
    I currently do not have an older version of iPhoto to test this on, but you might also try coping the Originals from the iPhoto Library of iPhoto 11.
    To do that;
    1. Right (control) click on the iPhoto Library in the Picture Folder on the MacBook Air
    2. Select Show Package Content.
    3. Click on the Originals Folder
    4. Navigate to the disired Event or photos and copy those images to your Flash or External Drive, then copy those to the older version of iPhoto.
    Beware do not move, add or delete anything in the iPhoto Library, Apple has intensionally hidden it in later versions to prevent people from messing things up.

  • My mac mini will not shut down.  I need to manually shut it off with the power button.

    My mac mini will not shut down or restart.  I need to manually shut it off with the power button.

    If you have more than one user account, these instructions must be carried out as an administrator.
    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
    Step 1
    Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
    View ▹ Show Log List
    from the menu bar.
    Enter "BOOT_TIME" (without the quotes) in the search box. Note the timestamps of those log messages, which refer to the times when the system was booted. Now clear the search box and scroll back in the log to the last boot time after  you had the problem. Select the messages logged before the boot, while the system was unresponsive or was failing to shut down. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V). Please include the BOOT_TIME message at the end of the log extract.
    If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
    When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
    Please do not indiscriminately dump thousands of lines from the log into this discussion.
    Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
    Step 2
    Still in Console, look under System Diagnostic Reports for crash or panic logs, and post the entire contents of the most recent one, if any. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if present (it may not be.) Please don’t post any other kind of report — it will be very long and not helpful.

  • Mac Mini will not boot OS, can I get to files with another Mac?

    My mac mini will not boot the OS proserly, it goes to a screen that tells me that some root folder can not be found.
    The install CD works and I can boot to it. The disk utility reports no problems, all disk repairs done and OK.
    The computer still will not boot to the OS.
    How can I get the files I need off the drive before I reinstall the OS?
    I have other Macs and fire wire cables, cross over cables, regular eithernet cables. What can I do?
    Thanks!

    How can I get the files I need off the drive before I reinstall the OS?
    Connect it to another Mac with a FireWire cable and start it up with the T key held down.
    (40535)

  • Would like to use an alarm clock.  I need the alarm clock to function from the sleep mode.  A review said that MAC products will not allow a program to wake up a Mac.  Is this correct ?  Are there any products in the Mac store what will function from the

    Would like to use an alarm clock.  I need the alarm clock to function from the sleep mode.  A review said that MAC products will not allow a program to wake up a Mac.  Is this correct ?  Are there any products in the Mac store what will function from the sleep mode ?  How do I check this out ?

    You can set times for your computer to turn on or wake from sleep in the Energy Saver system preference pane using the Schedule... button.

Maybe you are looking for

  • Polling for new Data in Tables with SQL-functions

    Hi In my table I have 2 columns: event_state : integer (0 = unread, 1 = read) min_process_time : date In the DB-Adapter-Wizard I can configure my event_state-Field for using as logical delete field. In the SQL-Query there is a ... WHERE event_state=0

  • Quicktime export, colors washed out

    I think this question has been asked before but I just couldn't find a good explanation in the archives. Wondering if anyone knows why, when I export my movie out of FCP to h.264 and then playback in quicktime, the colors become much more muted and w

  • How to display duplicates in Itunes 11

    Since I listen to a lot of classical music, accurately synchronizing track titles is very important... And, with an 80 gig Ipod Classic, I cannot get my whole library [95 gigs +] on it at one time...So, with itunes 10, you could display duplicates wh

  • Document number generation w. ref to Part no.

    Hi Gurus, We have created a template to upload Cutover data  in CV01N with the following series. Document Document Type Document Part Document version Description 1 DWG 000 00 TEST TEST TEST 2 DWG 000 00 TEST TEST TEST 3 DWG 000 00 TEST TEST TEST 3 D

  • Iir butterworth bandpass filter

    Hello everyone, I am trying to generate bandpass butterworth filter coefficients for one of my class projects. I am using "Butterworth CoefficientsVI" to generate the filter coefficients and using these coefficents I filter my input signal using "IIR