HT1414 My ipod touch shows white screen when i turn on. And, it does not register in my computer.

My Ipod touch don't start up as usual. It doesn't register to my PC. It shows white screen and some time other colors like green and blue. I trying restarting, but that did not work. I cannot restore the IOS because my Ipod touch doesn't even shows up in my Computer.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
  Apple Retail Store - Genius Bar

Similar Messages

  • HT1414 my ipod touch in white screen when i connect to the itunes can'tbe detected

    my ipod touch in white screen when i connect to the itunes can'tbe detected

    If not sucessful try:
    Try:
    - iOS: Not responding or does not turn on
    - If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • After my ipod touch restarts because it says plug into itunes and i does not pop up it does not appear in the apple window like it said it would.

    After my ipod touch restarts because it says plug into itunes and it does not pop up it does not show up in the itunes window like it says it would. why.

    Start here:
    iOS: Device not recognized in iTunes for Windows
    or
    iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X

  • My ipod just goes to a white screen when i turn it on

    my ipod just goes to a white screen when i turn it on

    A white screen is one of those symptoms covered here:
    iPod touch: Hardware troubleshooting

  • Ipod touch has white screen instead of home page, cant acess anything, any ideas?

    problem acessing Ipod touch. have white screen instead of home page

    dude your going to have to take it to apple because i can't tell if it's a hardware or software defect. your ipod might not be in warranty unless you got apple care.

  • Ipod touch has white  screen and not responsive

    ipod touch has white screen and not responsive, pls. suggest solution

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • 3rd generation ipod touch has white screen with lines going down. Can't access anything. Any ideas?

    My 3rd generation ipod touch has white screen with lines. Can't access anything. Any ideas?

    Have you tried connecting the device to iTunes in recovery mode and restoring it? See this article for instructions on getting your iPod into recovery mode.
    iOS: Unable to update or restore
    B-rock

  • White screen when I turn the Satellite M50 on

    I intermittently just get a white screen when I turn the computer on. Usually the problem is solved by switching the computer off and trying again - but sometimes I get a white screen again.
    It seems to be connected to use of external devices - can anyone give me clear instructions about what should/should not be connected when I start and shut down the computer? Or any other suggested solutions?
    Thanks

    Thanks for your reply/advice - and the tip about Antivir. I used to use AVG and then Norton came as a package with this laptop....will have a re-think when my subscription need renewing.
    I have updated the display/graphics driver but am still having the same problem of a white screen at boot-up. On reflection I think it is possibly a loose connection as I have just been a long trip with the laptop - including a fairly bumpy 4 hour bus ride - and I recall having the same problem several months ago which self-corrected after a similar trip (taking it down to a Toshiba ASP who never saw it as they were closed for the week-end and I had to get back to work!). This may sound strange but I took the laptop for a walk yesterday to see if any loose connection would shift and it then booted up on the second attempt rather than the 8th!
    I guess I'll have to take it to the ASP - unfortunately it's no longer under warranty.
    EDIT:
    Problem solved. High temperature caused this issue
    http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=23402

  • Why does my Mac stay on the white screen when I turn it on?

    Why does my Mac stay on white screen when I turn it on?

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.   
    There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
         a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
    b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    Sometimes a boot failure can be resolved by resetting the NVRAM.
    Step 3
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 4
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
    Step 5
    Boot in safe mode. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
    If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
    If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 6
    Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
    Step 7
    Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 8
    Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
    Step 9
    This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 10
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • My iPod Touch 4th Generation 8gb won't turn on and is frozen on the loading symbol/wheel, I tried the method where you hold the home and lock button lots of times and it hasn't worked! What do I do?

    My question won't all fit in but it says 'My iPod Touch 4th Generation 8gb won't turn on and is frozen on the loading symbol/wheel. What do I do?'
    I've had this problem from about two weeks and I forgot about it, but today I wanted to play on it and remembered that it's not working, I've tried connecting it to iTunes via my laptop but I'm not to sure how to update it because I thought that might fix it, but no luck. I've tried the trick where you hold the lock and home button but nothing happened apart from it just went back to the apple logo and then to the frozen loading symbol/wheel. I need help!

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • My Ipod is showing the loading sign while turning off and its frozen there.

    My Ipod is showing the loading sign while turning off and its frozen there. My computer wont reconize it either. My Safari didnt work so I thought that I will turn it off to see if its working after and it just gotb stuck in the loaeding sign while turning off.

    Try here:
    iOS: Not responding or does not turn on

  • 4th gen ipod touch has white screen

    I have a 4th generation Ipod touch. The screen turned white all of a sudden for no reason. I've tried holding buttons letting it die and plugging it back in but the white screen is still there.It still makes noise. like the other day it was making a noise like someone was calling it. Then if I press the sleep/wake button and home button it takes a picture and I can hear the noise but still have the white screen. Does anyone know what I can do? Thanks

    try one of these ways:
    > restore you iDevice with iTunes in Recovery Mode (if you have to... back up your device before restoring)
    > let the battery go completely dead.... then plug it using USB to PC or Mac OS
    > replace the LCD with www.ifixandrepair.com
    > go to the Apple Store (official store not retail) and see what they can do. they can replace your device for refurbished price

  • Ipod touch 4g white screen

    My iPod Touch 4G's screen went white after using draw something and facebook apps. I've tried resetting, DFU, restoring and connecting it to iTunes... no work. But the screen is not completely white, it looks blackened now. I've tried holding menu button and then Sleep/Awake button and volume button for over ten or more times now. Please i got to fix this or I'm dead!!!   PLEASE HELP MEEE!!!!!
    Device: iPod Touch 4G
    Memory: 32GB

    Let the battery fully drain. After charging for at least an hour try everything again
    If not successful ,time for an appointment at the Genius Bar of an Apple store.

  • Ipod touch 4 white screen

    my ipod toch 4th generation went completely white and i dont want to loose all my informatiom what do i do beside restarting it?

    See  Display Shows White Screen Here  >  http://support.apple.com/kb/TS2771
    If no joy... Try letting the Battery Fully Drain... Then Charge the Device for at least 30 Minutes...

  • HT201210 ipod touch gen2 white screen , ive tried everything apple says to try ,still no change,what am i supposed to do now

    ive tried everything apple says to try ,still no change,what am i supposed to do now

    See  Display Shows White Screen Here
    http://support.apple.com/kb/TS2771
    If that does not work... try letting the battery fully drain.
    Then Charge for an Hour and try the Reset again.

Maybe you are looking for

  • Inactivate the print button is the ABAP list

    How can I inactivate the print button in the report program (ABAP list)? I can inactive the print button on selection screen by using 'RS_SET_SELSCREEN_STATUS'. But can't achieve the same effect after the program jumped to the list output screen. Tha

  • How do I fix my problem with Artist and Sort Artist?

    I have all my songs sorted by Artist and because I have songs that feature other artists I use the sort artist field. In itunes it all looks fine but when I sync it with my iPod Nano 5th Gen one of the artists names comes up as the artist for all son

  • Error while deploying same BPEL process created by jd10.1.3.4 then 10.1.3.3

    Hi, My SOA suite is in 10.1.3.3. I have created a BPEL process using jdeveloper 10.1.3.4 and deployed it in SOA suite 10.1.3.3, but when I created a same (everything same, even name) with jdeveloper 10.1.3.3 and deployed it, it is giving me the below

  • PM Order Operations Default Unit of Measurement

    Halo Experts, We have a problem in UOM for PM/CS order operations. We have defined HR as default value of UOM for operations in IMG. Business wants to change at the order level to H as UOM and it is manually keyed in and saved. But when we check with

  • Sales Order -- Purchase Req -- Purchase Order ..... Sales Document flow??

    Hi Guys, We have a process where we proccure few parts externally. When a sales order is created in our system based on the item category config we are able to create a purchase requition automatically. This Preq is further used to create a PO based