HT3180 My Apple TV turns on but no image on TV screen

My Apple TV has been unplug over 30 sec. or restart by using 3,4 button on remote but still no image on TV screen. The LED light blinking for a while and turn on for long without blinking. No image shown on screen.
I have used for several times from new without problem on previous.

You may need to grab a micro usb cable and restore in iTunes.
http://support.apple.com/kb/HT4367?viewlocale=en_US&locale=en_US

Similar Messages

G5 turns on but display stops at gray screen+apple logo

Can someone tell me why my G5 turns on but display stops at gray screen+apple logo. The keyboard and the superdrive not responding. After a minute the fans kick in and grow louder and faster...?? I tried a reset with the P and R but keyboard N/S. USB have power. I do get the start sound then the gray logo+screen.
Thanks for the help anyone!!
G5 dual 2G Mac OS X (10.3.9) 2G RAM, 23" display

I was getting a similar issue yesterday, stuck on the
grey screen, then the G5 turned into mini turbine
engine. I'm not sure what fixed it, i took out the
plastic wind deflector and noticed three leds next to
the RAM slots were lit up.. with some quick googling
bringing me back to apple's support pages, it turned
out the lights came up because the deflector shield
wasn't in place. Anyway myabe it was slightly out of
place, but that coupled with unplugging the power
cable for some moments seemed to help, and i was able
to get past the logo screen etc..
but i was still getting intermittent issues, with
startup and programs, and getting plenty of crashes.
So i did the Apple Hardware Test, and after 3hrs it
turned out my RAM was at fault. I recieved the
machine only a week back, since then i've added new
RAM, which was the exact same Samsung RAM that apple
use, though one stick didn't share the exact same
serial, it was still the same spec.. anyway i've
removed the pair of 1GB sticks for the time being,
and since doing so, i've got my mac running to its
full strength.. i just hope i can sort out this RAM
issue and not have blown my money.
Thanks for the help but I tried the cable thing etc and nothing so I reformated the disk (clean install and I'm back to normal now...so the RAMS were not the problem in my case.
Also, I'm glad I backed up all my stuff frequently therefore, no losses...
G5 dual 2G Mac OS X (10.3.9) 2G RAM, 23' display

Computer turns on but nothing appears on the screen

Hi,
I have had this desktop computer for about 2 years. I usually use it almost daily and turn it off at the end of the day. Every few months or so the computer would turn on but nothing would appear on the screen. I would have to hold the power button to turn it off then turn in on a couple times or wait until the next day and the computer would turn on and everything would appear on the screen and work perfectly. Last week, the computer once again turned on but nothing appeared on the screen, except this time, after a week, the computer will now turn on except there is still nothing appearing on the screen. I no longer hear the fans running, however, I hear everything else running as normal. I have unplugged and re-plugged in all the cords multiple times and still, nothing.
Please help! Thank you.

Kelly, welcome to the forum.
When requesting help you should always include the make/model (i.e. p6-xxxx) of the computer and/or monitor. This information is necessary for us to review the specifications of them.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

I dropped my phone it turns on but I have a black screen

I dropped my phone. I think it turns on but the screen is black. Any tips?

Keywords: Careful and Protective Case. They will protect but are not 100% .
OtterBox Defender Series Cases | OtterBox.com
Smartphone Cases

If my iPhone 3GS turns on but cannot use the touch screen, could the Processor be the problem?

I recently dropped my iPhone 3GS but cannot use the touch screen. I took to a local repair shop and they tried replacing the digitizer and some other items but still could not get it to work. They advised that the Processor could be the problem. Is this true? If so, can the processor be replaced without losing data? Additionally, my phone has a lock code and when I try to connect it to my desktop to back up, it states that I need to enter my 4 digit pin first, which of course I cannot. Any workarounds here or am I SOL?

Hook the phone to a computer running iTunes and backup to the computer. Copy pictures off the phone manually to the computer.

Audio but NO images show - black screen -up in the canvas viewer window????

Hi all,
I'm a newbie having problems with a file in FCP where the audio plays and but no image shows up in the Canvas window. I imported the audio from my camera and had some kind of a problem in the browser window where the sequence didn't show up with the actual length of time...it read 00:00:00. I reimported the quicktime file into FCP Express, and then it showed up fine. When I reopened it in FC Pro, this time, the sequence shows the full amount of time of the file, but I'm still getting all black in the canvas window. I'm at a loss to explain this. I have a feeling I did something wrong during the initial import, and so the actual source file is somehow corrupted. But when I open the source file in quicktime, it plays fine. It's only within FCP that it's all dark.
Help!!!!!
Thanks in advance
Message was edited by: Gary King3

sounds like you do not have a source file that FCP recognizes.
What camera and what codec does it shoot? did you convert to a prores or standard QT format before or after ingesting?
bogiesan

My ipad turns in but will not boot up. screen stays blank. I've tried resetting it and rebooting from itunes. It says it is done but the screen still stays blank. The apple icone will show up intermittetly.

I turned on my ipad after charging it and the screen went blank. I tried the home button and on off button and that did not help. I went to iTunes and rebooted the ipad and restored it and it asked me to reboot from the ipad but the screen is still blank. It will go to a blue screen if I hit the on/off button. What else is there to check?

If you restored the iPad, there is nothing else to check. I suggest that you make an appointment at an Apple Store Genius Bar and let them evaluate your iPad.

HT1551 Apple TV turns on but no picture

I Have an Apple TV nothing on screen

What TV are you using? How is.the device connected? Are you on the right input? Tried different ports?

Apple Tv is on, but there is a black screen...help

I have had my apple tv for a year and now when I turn on the TV and go to my channel setting there is nothing but a blank screen...any help?

Hello there mpenna16,
It sounds like your Apple TV is connected to your television but the screen is black and shows no video. There can be a number of causes for this, and I would recommend that you use the following troubleshooting to help resolve or isolate the issue:
Apple TV (2nd and 3rd generation): Troubleshooting video issues
http://support.apple.com/kb/TS5148
Your TV picture is completely black or has other quality issues such as static or blurry video
Confirm the settings and configuration of your television.
Check to verify that your TV's video input matches the HDMI connection.
Refer to the manufacturer's user guide for assistance with changing your TV input or picture mode.
Verify that your television meets the Apple TV minimum resolution requirements.
Verify that the Apple TV's power cable and the HDMI cables are securely connected.
When connecting to power, observe the front LED on your Apple TV for activity. If no light is visible, try a different power outlet or power strip.
Connect the Apple TV directly to your television, bypassing any home theater receivers, splitters, repeaters, or switches temporarily.
Inspect all cables for any kinks, tears, or other evidence of damage.
Verify that the HDMI cable being used with your Apple TV is a bidirectional cable. Although rare, single-direction HDMI cables do exist. If unsure, try flipping the connection between your Apple TV and television.
If all else fails, try a different HDMI cable.
Change the Apple TV resolution:
Press and hold the Menu and Up button on your Apple Remote for six seconds.
The Apple TV will automatically cycle to the next resolution at approximately 20 second intervals.
Press Play on the Apple Remote to keep the current resolution or Select to manually cycle to the next resolution.
Reboot your Apple TV by holding down the Menu and Down button on the Apple Remote for six seconds. Allow the Apple TV a few minutes to restart.
Note: If the Apple TV video functions correctly after bypassing a receiver, switch, or repeater, please refer to the accessory manufacturer's user guide for additional support.
Thank you for using Apple Support Communities.
All the very best,
Sterling

Why is my ipod touch 3g turning on but not displaying the home screen?

my ipod has worked without an issue for 3 years, however yesterday it froze in an app and then displayed the apple icon and then the display turned off. Since then my ipod has been repeatedly attempting to boot up unsucessfully; displaying the apple logo but never going to the home screen. the only way to stop this is to reset it and leave the ipod switched off. Help would be much appreciated

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

Received from Apple new iPhone 4s but can not activate. Screen states activation servers not available. What's next step?

I purchased a new iPhone 4s as a replacement for a 3GS. The phone starts up with configuration, recognizes my home network wi-fi, but for the past 3 days, all I can advance to is the activate your phone screen. I have tried through iTunes, Wi-Fi and cellular and while each has a different wait time initially, in the end it is the can't activate the phone message with the description that the activation servers are unavailable. Considering that the first iPhone 5 will start this process tomorrow, if the servers aren't prepared now, what will be happening to everyone tomorrow? I am in Oklahoma and all of my devices received the updated IOS 6 without problems, but this new phone is just waiting.

When Apple replace an iPhone and the faulty one is locked to a carrier in this case it will be T-mobile ( they do not sell unlocked iPhones) they will replace the iPhone with a locked one to that carrier
So in theory you should have an iPhone locked to T-Mobile
Call Apple and they can tell you if it is locked and to which carrier .
I am also doubtful that a BB sim will work in an iPhone even if unlocked due to BB Messenger

I have a macbook pro with lion os. and i want to connect it to my optoma dlp projector. when i connect through a mini display to vga adapter in MBP it detects as OPTOMA XGA but no image on the screen.

i have a macbook pro. i want to connect it to projector and i have a minidisplay to vga adapter. i could connect my MBP to benq projector successfully and for all other displays( Monitors). but when i connect it to optoma projector, MBP detects the display as OPTOMA XGA but nothing on bigger screen. i tried changing the resolution and refresh rate also but no changes.
In my office we got benq projectors , for that it is working very well.(plug and play).
and also i want to say that there is no problem with the optoma projector seems, because all other windows laptops are working well with that.
i was struggling with this since one month. i googled it could not find anything supportive for my problem. please help me regarding this. i am new to apple. i hope there must be genius around here.
thnak you

Rwogera wrote:
I couldn't transmit sound either, do i need another cable like Kim said? i mean it cant be transmitted through this HDMI port? as for me i have one of the latest mac pro with intel core i5..tnx
I need to know which MacBook Pro you have. Only mid-2010 and later MBP's transmit sound through MiniDisplay Port to HDMI. I have no information about the Mac Pro, so you might want to go to that Forum and ask there.

2009 Core 2 Duo iMac Display not turning on, but everything else is.

The iMac turns on, but NOTHING is on the screen. The machine boots fine, and can even connect to an external display. Help?

That is a tough problem since you don't seem to be able to boot from anything, hard drive, install disks, external. Sounds a lot like a failure on the logic board. And goes to the AirPort card twice before failing. Are you able to take the iMac to an Apple Retail Store genius bar or an Apple authorized repair service? This would be a good problem for their diagnostics.

My iphone wont turn on!! please help!! the apple logo turn on only.

okay so yesterday i went to apple store cos my iphone needed to be fix and today when i was about to put all my stuff in like from a back up i decided to erase all that was already on my iphone so it wont lake long, so i went into settings, rest, erase all content and settings, and now my iphone will not turn on at all. like the apple logo turns on but then the little circle thing that tells its loading appears on top of the logo please help, should i take it into apple again?

Phone not recognised in itunes
iPhone not recognised by iTunes on PC
iPhone not recognised by iTunes on Mac

Apple Logo turning on and off on screen!!

My screen keeps having a apple logo turning on and off..
My screen is firstly 'non-lit' then 'lit' in bout 10secs.
Is this what u call a backlight?!
If so, how can u turn it off?
I cnt even acess any files.. or listen to music.
I tried resetting my ipod over and over again.. But it did not respond.
I just had my ipod for less than a day.. How unlucky!

Like the other two individual's i too am having this same issue. The only difference is now this is the second faulty iPod Nano i have recieved. I am able to press the select and play button for 6 seconds and force it into disk mode, but if i return to regular status, the nano returns to the same state of blinking.
I've been through the steops of reseting and even restoring to factory, I can see the ipod on my desktop as well as in itunes but once i eject the nano, the screen either stay blank, or goes back to to blinking. How do i get my nano to be like a normal one like everyone else has, without anymore issues, bad enough having issues with apple care to transfer my apple care for the nano to this new one from the old faulty one i had.

HT3180 My Apple TV turns on but no image on TV screen

Similar Messages

Maybe you are looking for