HT3728 After upgrading to mountain lion, my Mac no longer sees the Time Capsule.  What am I doing wrong?

After I upgraded to Mountain Lion, my Mac cannot access the data disk on the Time Capsule.  Who else is having this problem and have you been able to solve it?

Bonjour PanicRev16
   I use Grapher 2D 3D on my early 2006 iMac, but I tried it on my wife's Macbook Pro with Lion then Mountain Lion : no problem with Grapher 2.1  3D gcx files, Grapher 2.3 loves them !
   You can try the 3D Grapher 2.1 files from the website  http://y.barois.free.fr/grapher/  and see the result on your Mac Mountain Lion.
   I updated Grapher documentation and bugs of this website on 15th december 2012 (Lion, then Mountain Lion).
  Au revoir,
YB24

Similar Messages

  • After upgrading to Mountain Lion my Mac Book pro takes 1min 15 to load sec to open, never took that long.

    after upgrading to Mountain Lion my Mac Book pro takes 1min 15 to load

    Apple made some changes to increase security that slowed the boot time.
    Startup - Slow Boot
    Startup - Slow Boot (2)
    Startup - Slow Boot (3)

  • After upgrading to mountain lion my mac is very slow?

    Hello
    After upgrading to mountain lion my mac is very slow
    It was starting in 10 seconds and shuting dow in 5 seconds and now it's taking more than one minute to start it or shut down it and everything is slow
    why????????/
    Thanks

    First, back up all data immediately, as your boot drive might be failing.
    Take these steps when you notice the problem.
    Step 1
    Launch the Activity Monitor application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
    Select the CPU tab of the Activity Monitor window.
    Select All Processes from the menu in the toolbar, if not already selected.
    Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
    Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
    Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
    Step 2
    You must be logged in as an administrator to carry out this step.
    Launch the Console application in the same way as above. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left.
    Post the 50 or so most recent messages in the log — the text, please, not a screenshot.
    When posting a log extract, be selective. Don't post more than is requested.
    Please do not indiscriminately dump thousands of lines from the log into a message.
    Important: Some personal information, such as your name, may appear in the log. Edit it out before posting.

  • After upgrading to mountain lion e-mail no longer pushes to my i-Phone

    after upgrading to mountain lion e-mail no longer pushes to my i-Phone I have to launch the mail app on phone to retrieve mail now

    The OS on your Mac has nothing to do with behavior of email on your iPhone. The only thing I can imagine is that Mail on your Mac may be receiving messages and marking them as "read" before your iPhone has a chance to receive them. What kind of email account are you talking about here!

  • After upgrading to mountain lion my mail fails while reformatting the database

    I recently upgraded to OS X Mountain Lion and when I try to start the mail app it goes into a reformat the database process that never ends.  I force quit the mail app and shutdown the MacBook Pro.  But when I reboot and try mail again it does the same thing.  What can I do? I don't care about my mail database.  I would like to begin receiving emails, however.

    Maybe this will help. If you monitor the "More Like This" box (top right), other threads appear. Opening them usually displays other threads.
    https://discussions.apple.com/thread/3197363

  • After upgrading to Mountain Lion, all my pictures are gone from iPhoto.  What happened?

    This is very upsetting.  ALL my pictures are gone from iPhoto.  What happened, and how can I get them back?

    Look in your user folder/Pictures. Is the Library there?
    Try rebuilding the library.
    iPhoto Library rebuild

  • Google Talk not working with Messages after upgrade to Mountain Lion

    After upgrading to Mountain Lion, I'm no longer able to use Google Talk with the new Messages App.  It worked fine on iChat, but now I cannot enable the account.  When I try to check the enable box, it immediately unchecks itself and nothing happens.  Any suggestions?

    Welcome to Apple Communities
    Open Finder, press Option key and select Go > Library. Open Preferences and delete com.apple.imessage.bag.plist and com.apple.imservice.iMessage.plist

  • After upgrading to Mountain Lion on my 2011 27" iMac, my Mac occasionally lock-ups.

    After upgrading to Mountain Lion on my 2011 27" iMac, my Mac occassionaly locks up while using Safari, Mail or Dreamweaver and I have to d a force-quit, then restart my Mac.  Anybody having similar probelms?
    I am thinking about doing a clean install of Mountain Lion.  Would I be able to restore my applications and data from Time Machine after the re-install?

    My 24 inch iMac... 2.8 GHZ dual core (Early 2008) is having the same problem.  After it sleeps, I go to use something... and the beachball of death occurs.  This happens multiple times a day... and let me tell you... it is annoying... and I am the one who is being annoyed!
    It could possibly be revolving around safari... as that is really the only thing that is running consistently.  I don't use iTunes on this iMac as I have so many other Macs up and running in the house... and I never consume media on it... so I kind of dismiss iTunes being the culprit.
    This is majorly affecting my Mac... in terms of reliability and uptime... which coincedently is the main reason why I switched to Mac in 2008.  This is my only Mac that could upgrade to ML... so I don't know how widespread this is... but I hope that this problem can be solved...
    I agree with another person who commented on this issue... do we really need a 10.8.1 update already... to fix this?

  • After upgrading to Mountain Lion I am not able to access "security and privacy" button under "system preferences". I like to activate "find my mac" but cannot access privacy setting after upgrade. Kindly advice.

    After upgrading to Mountain Lion I am not able to access "security and privacy" button under "system preferences". I like to activate "find my mac" but cannot access privacy setting after upgrade. Kindly advice.

  • Hi...I have this problem, everytime I want to print something out the mac asks me for the computer password...that is really becoming annoying after. That happened since I upgraded to mountain lion. How can I stop the computer from asking me that?

    Hi...I have this problem, everytime I want to print something out the mac asks me for the computer password...that is really becoming annoying after. That happened since I upgraded to mountain lion. How can I stop the computer from asking me that?

    If you are printing via a Windows shared printer and it is the Windows user account that you are being prompted for then you can save this in the Keychain, as shown below.

  • I have a mac, would like to upgrade to mountain lion from mac os x, anybody experienced any problems after this upgrade, thanks

    i have a mac, would like to upgrade to mountain lion from mac os x, anybody experienced any problems after this upgrade, thanks

    Check that your computer is compatible with Mountain Lion.
    To check the model number hold down the option/alt key, go to the Apple menu and select System Information.
    iMac (Mid 2007 or newer) model number 7,1 or higher
    MacBook (Late 2008 Aluminum, or Early 2009 or newer) model number 5,1 or higher
    MacBook Pro (Mid/Late 2007 or newer) model number 3,1 or higher
    MacBook Air (Late 2008 or newer) model number 2,1 or higher
    Mac mini (Early 2009 or newer) model number 3,1 or higher
    Mac Pro (Early 2008 or newer) model number 3,1 or higher
    Xserve (Early 2009) model number 3,1 or higher
    Your Mac needs:
    OS X v10.6.8 or OS X Lion already installed
    2 GB or more of memory (More is better - 4 GB minimum seems to be the consensus)
    8 GB or more of available space
    If you can/do upgrade, I recommend you make a copy of the installer and move it out of your Applications folder. The installer self-destructs. The copy will keep you from having to download the installer again.  You can make a bootable DVD/USB stick to install using this free program.
    Bootable Drive DVD or USB Flash Drive – Lion Diskmaker
    Our 2 computers haven't experienced any significant problems, even though others have. I find it much better than 10.7 Lion, which I used for a week before reverting to 10.6.8
    Mavericks is supposed to be released this fall, so you may want to wait.

  • After upgrading to Mountain Lion 10.8.2, I cannot print to my Samsung laser printer ML 2525w?  How can I get this set up to print?

    After upgrading to Mountain Lion 10.8.2 on my iMac, I cannot print to my Samsung B&W Laser printer ML 2525W either by USB or wireless.    Any help on how to setup or reconfigure would be apprecaited.
    I either print blank pages or prints one time then goes off line, or spits out a bunch of blank paper, etc.  Have gone through all the standard fixes, reboot, reset , reload driver, etc.

    From the link to the Thread you provided, I worked through the one message procedures that were listed.
    For ease of reference, I have copied them and printed them below.  This was an old thread but the guidance still works with no firmware upgrade required.
    I would stress that you MUST delete any and all files relating to USB connection of the printer to the MAC, including all print drivers (from both Apple and Samsung either from CD or web downloads) and all print queues, etc.  I was only able to get the printer to properly hand shake with my Mac by setting it up wirelessly after all old files were deleted with hard power off reboots on both the Mac and Printer. 
    I hope that someone from Apple will pass this note along to their programing department because there is some type of incompatibility in the new ML OS and the Samsung ML2525w print dirvers used for a cable (USB) type connection.  Apple needs to be talking to Samsung to get the USB issue resolved.  I am going to post this same message on the Samsung site to see if someone from there will contact Apple to work together on a final solution for USB connectivity.
    Here is the steps I followed to get my ML2525w to work in the wireless mode.  Again, I cannot stress the need to clean out all the old files (drivers, print queues, etc. - everything) before setting up wirelessly. 
    As a note, I ran this printer with Lion for almost 2 years and it always worked fine (both wireless and USB).  From other comments on the thread, users were good with this printer using Lep. and Snow Lep also. - - no issues from either a USB connection or wireless until Mountain Lion.
    Before the fix, I was experiencing many of the same issues as described on user chat threads, printer going offline after a print job.  1st page sometimes printing but all the rest of the pages were garbage.  No printing at all. Printer just running a bunch of blank pages out. etc.
    I run an iMAC 27" desktop with the ML OS upgrade just installed from Lion.
    "I've just installed one of these printers for my parents.
    First of all, don't waste your time connecting the ML-2525W as a USB printer. The printer will go offline after each print job. It's hopeless, at least (I assume) until Samsung gets around to publicly releasing a firmware update.
    Instead, you have to use the ML-2525W as a wireless printer. In that mode, it works fine.
    This is what I did:
    (1) First, if you have already attempted to install the Samsung driver software from the included CD-ROM, uninstall it. Get the uninstaller from the Samsung support site:
    http://www.samsung.com/us/support/downloads/ML-2525W
    Download the "Printer Driver (ver. 4.0)" ZIP file. It unzips to a folder that contains the uninstaller. Likewise, download the "Smart Panel Driver" ZIP file and uninstall the Smart Panel software.
    (2) Disconnect the USB cable from the printer, if it is connected. Pull the power plug on the printer and power cycle it.
    (3) Restart your Mac.
    (4) Go to the "Printer Driver (ver. 4.0)" folder that you previously unzipped. Inside it is a folder named "WirelessSetting". Open the folder and run the "Wireless Setting.app".
    (5) The application will ask you to connect the USB cable to the printer. Do so, and the Mac should be able to communicate with the printer to perform the wireless setup.
    (6) The application will show you a list of wireless networks. One of them is the wireless interface in the printer (ad-hoc). You can ignore that unless you intend to use the printer without connecting to another wireless network. In my case, I selected the wireless network in my parents' home (infrastructure) and entered the security passphrase. The application then configured the wireless interface in the ML-2525W to connect to the home network.
    (7) The Wireless Setting application will then tell you to disconnect the USB cable.
    (8) After finishing the Wireless Setting application, go to Word, Textedit, Pages, or Safari, and select a file or page to print. In the print dialog window, you should see the ML-2525W as a "Nearby Printer" (i.e. via Bonjour). Select the ML-2525W, and your Mac will automatically connect to Apple's Software Update and download the latest Samsung driver. If for any reason the Software Update download does not succeed, you can manually download and install the Apple driver using the previously published link in this discussion.
    (9) After that, you should be able to print to the ML-2525W whenever you want, without the printer going offline.
    (10) If you have a USB printer queue still in your Print & Fax Preferences (from your previous unsuccessful attempt to connect via USB), you can delete it. You only need to keep the Bonjour queue.
    Obviously YMMV, but in my case this procedure got the printer working reliably without the need for a firmware update."
    MacBook (white 12"), Mac OS X (10.6.5)

  • After upgrading to mountain lion, contribute cs4 did not open

    After upgrading to Mountain Lion, I found that Contribute CS4 did not open.  In searching for an answer I found the following on the Adobe forum:
    "Earlier versions of Adobe Photoshop (CS3 and CS4) software were also tested with Mountain Lion and there are currently no known issues."
    So continuing to search, two days of frustration ensued as I "chatted" with 2 unhelpful Adobe customer support reps, searched unhelpful Apple and Adobe websites and posted my question in various places.  Finally I found that the above statement was completely wrong when I received the following from an Adobe staffer:
    Mountain LION is not a supported platform for Adobe Contribute CS4. The supported versions are Latest Adobe Contribute 6.5 and Adobe Contribute CS5.X.
    And now I have to spend hundreds in order to maintain my website after upgrading to Mountain Lion.  I don't even know to whom I should take my complaint, Apple or Adobe.  Does this mean I have to research every piece of software I use before upgrading my Mac?  At the very least, Mac owners should be forwarned of platform support failures for major 3rd party producers. I'm doing my bit here.   How about you taking some responsibility?

    I just baught a new imac from the apple store and loaded mountain lion when I got home due to the time it would take there.  I then used migration assitant to load CS4 from my mac pro that is using snow lepord.  This worked flawlessly. CS4 and Bridge work great.  I then downloaded the mountain lion upgrade to my wifes mac pro that was also using snow lepord and once mountain lion was instaled it disabled CS4 compleatly.  I will repost the results tomorrow. I believe that I can reinstall CS4 to her mac pro now that she has mountain lion installed using migration assistant from my mac pro since it worked this way with the new imac.  I hope this works because I want to upgrade my mac pro to mountain lion but can't afford to lose CS4. 

  • After upgrading to mountain lion no contacts says no cards

    After upgrading to Mountain Lion when I go into Contacts, no contacts are displayed.  It says no cards.  One solution I found on this site says to go into libraries and then the Application Support folder and delete the address book there and then restart the computer.  I don't have Address Book listed in the Application Support folder.  Any ideas?

    The OS on your Mac has nothing to do with behavior of email on your iPhone. The only thing I can imagine is that Mail on your Mac may be receiving messages and marking them as "read" before your iPhone has a chance to receive them. What kind of email account are you talking about here!

  • After upgrading to Mountain Lion, i can't connect to app store or safari

    After Upgrading to Mountain Lion, I can't access the app store, itunes store, Safari - anything that requires the internet.  I tried resetting my modem and rebooting.
    I also tried deleting items from the keychain that look like they are related to the above.  When I did that and rebooted, It works for a little while, and then gets back to where it won't login to anything on the internet and safari won't load anything.

    This means that at some time you had the iWork ’09 trial installed. You need to delete the trial & then reinstall from the boxed DVD or the Mac App Store. The files to delete are the iWork ’09 folder from the main HD > Applications; the iWork ’09 folder in HD > Library > Application Support & the individual iWork application plist files found in HD > Users > (your account) > Library > Preferences for each user. Yvan Koenig has written an AppleScript that removes the files. You can find it on his box.com account in for_iWork'09 > other_iWork'09 items > uninstall iWork '09.zip.

Maybe you are looking for