I am trying to setup VPN with QuickVPN

Hi I am trying to setup VPN with WRVS4400N and Quick VPN on client side. I am fairly new to VPN and did some research and looked through the manual but can't seem to get it to work so far and from what I noticed many people are having this problem. So hopefully someone can tell what the problem is or at least point to right direction on solving this.
Basically it gives the "Failed to establish connection" generic error, shows it almost instantly..
It also showed the certificate error before but then I read about putting it in the installation directory and it stopped showing it, and whats strange is later I removed it but it doesnt show the error any longer, so don't know if its caching it somewhere or what can be going on...
In effort to look for answer and test things out I tried to connect to another location and setup a WRV200 router, I also get the same error but not instantly, it even shows "Activating Policy" but then doesn't go farther and shows the generic error...
Also with this setup strangly it always shows the certificate error, no matter if I put one in directory or not... Even tried to name it as the WRVS4400N certificate name...
Anyway VPN IPSec is disabled, and Client Accounts are configured and changed password several times to make sure its correct, VPN Passthrough enabled on all 3 options.
I tried to disable Windows Router, I also have a router in place do I possibly need to open some type of ports for the QuickVPN client?
Don't know yet whats going on if I am missing something or if there is some problem that needs work-around but if you know the answer or guesses of answer please let me know.

Hi Aleksandr,
since this question is about a product in the Cisco Small Business / Linksys range, I suggest you move it to the community, where you will have a better chance of getting expert advice.
best regards,
Herbert
Cisco Moderator

Similar Messages

Need help in setup vpn with IGMP enabled !

hi all
i hve cisco 2901 router and i want to setup vpn that allow IGMP ,
can somebody help me with it or at least sample configuration ?
can it be done from http gui ? or it is mandatory from cli ?
regards

Hello,
So you plan to send multicast traffic over the tunnel?
It could be possible to do it via both ways, thing is is harder to get assistance via GUI as for example I have no access to any router. I reply based on commands that I remember so CLI is a must.
I would recommend using a GRE tunnel to send the Multicast traffic through it
Looking for some Networking Assistance?
Contact me directly at [email protected]
I will fix your problem ASAP.
Cheers,
Julio Carvajal Segura
http://laguiadelnetworking.com

Ipad 3. trying to Setup icloud with windows 7 laptop, but Safari says "safari cannot Download this file"

Safari window pops up with "Safari cannot download this file"

There is an app you can download for xp, i havnt tried it because im not going to use icloud but if you go onto the ipad tab and then icloud there is a link on there.

What is the WPS button on my access point? I am trying to setup wirelessly with a canon MX892 printer

Printer setup instructions say to press the WPS button on the access point (my 4th gen Time Capsule). Does that mean hit reset and will I have to setup every other device again by doing that?

No, do not hit reset .. it is not a WPS button.
Apple products do not use WPS, so no WPS button is needed. And they have no need to implement one.. nothing exists outside the Apple bubble.. didn't you know that??
Read the forum expert Tesserax instructions for using WPS. https://discussions.apple.com/message/16034147#16034147
But it is better to plug in your printer to a mac by usb and use the disk provided to do a full manual setup of wireless.. WPS is simply the easy way.

Trying to setup RAID with 2 80GB Western D and K7N2 Mainboard.

Thank you for looking at my problem in advance.
Here is my problem. When I go to the fastTrak setup it only shows 1 hard drive. I have both Wetern Digital 80gb hard drives connected to one IDE cable going to the ID3 connector on the MB.
These drives are not SATA, they are just plain ATA133 IDE hard drives. Any help would be greatly appriciated! Thanks,
Jamey

no normally in raid they would have an ide each ,wether onboard raid or a card
im wondering if both on the same will negate any benefits
it either reading or writting but it can only do it to one drive one one ide at a time
thats what i see as a problem

Do I need a security license to setup VPN on router?

Hi All.
I'm trying to setup VPN connections on 2 different routers and I'm not sure about that Do I need a security license to setup VPN connection on router?
First one is 1941-K9 site-to-site.
Second one is 887G-K9, EasyVPN connection.
Both of them don't work properly. What do I need to check on both routers to see if they're abled for vpn connection, maybe some commands as well.
Thanks in advance.
Regards,

yes, for VPN you need a security-license.
The 1941 should show the following line:
rtr-01#sh ver | b Technology
Technology Package License Information for Module:'c1900'
Technology    Technology-package          Technology-package
              Current       Type          Next reboot
ipbase        ipbasek9      Permanent     ipbasek9
security      securityk9    Permanent     securityk9
data          None          None          None
The 887 comes by default with the "Advanced Security" feature-set. That's all you need for that device.
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Cannot setup VPN (WMI failure?) - Server Essentials 2012 R2

Hi,
Last week i setup a new Server Essentials 2012 R2 (fresh install). Everything apart from the Anywhere Access has sucessfully been setup and the server is in a production Environment.
When i try to configure Anywhere Access and setup VPN + RemoteDesktop , the wizard fails. VPN cannot be setup , retry.
Two Issues:
The VPN setup/configuration fails (Lets start with this one, could be related to second issue).
Remote Desktop setup is completed. However the "Remote Desktop Gateway" service cannot be started because the dependant service RPC/HTTP Load Balancing cannot start.
Troubleshooting steps taken on the VPN setup Issue:
Restarting the server (multiple times)
Rerunning the wizard (multiple times)
Checking if the correct roles has been installed by Server Essentials
Checking log files dashboard.log (The error found)
Run sfc /scannow (errors found and corrected)
Run DISM (OK)
Tried to setup VPN manually using the RRAS GUI (Error: Installation of the Routing and Remote Access service failed because Class not registered 80040154)
Further I've concluded that the 1st (VPN) issue is probably casued by malfunctioning WMI
In the dashboard.log , when running the VPN setup an error can be found on one of the setup steps:
[6684] 140723.170909.2619: RemoteAccess: PS > RemoteAccess\Install-RemoteAccess -VpnType Vpn;
[3320] 140723.170910.1772: DomainManagerObjectModel: Calling KeepAlive for instanceID=1
[3320] 140723.170910.1772: DomainManagerObjectModel: KeepAlive succeeded for instanceID=1
[6684] 140723.170918.1943: RemoteAccess: PS Exception (catch and rethrow): System.Management.Automation.MethodInvocationException: Exception calling "EndProcessing" with "0" argument(s): "Object reference not set to an instance
of an object." ---> System.NullReferenceException: Object reference not set to an instance of an object.
To troubleshoot this further, i've run the PS command "Install-RemoteAccess -VpnType Vpn" manually. This gives me the following error which Points to a WMI issue
PS C:\Windows\system32> RemoteAccess\Install-RemoteAccess -VpnType Vpn
RemoteAccess\Install-RemoteAccess : Provider load failure
At line:1 char:1
+ RemoteAccess\Install-RemoteAccess -VpnType Vpn
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : NotSpecified: (PS_RemoteAccess:root/Microsoft/...PS_RemoteAccess) [Install-RemoteAccess]
   , CimException
    + FullyQualifiedErrorId : HRESULT 0x80041013,Install-RemoteAccess
Ran WMIdiag - Found errors. The most interesting error is found below
53059 22:43:35 (2) !! WARNING: WMI provider DCOM registrations missing for the following provider(s): ..................................... 3 WARNING(S)!
53060 22:43:35 (0) ** - ROOT/CIMV2/TERMINALSERVICES, AAGProvider ({75D15B16-228C-499F-A0FC-E4899AC870CE}) (i.e. WMI Class 'Win32_TSGatewayResourceGroup')
53061 22:43:35 (0) **   Provider DLL: ''
53062 22:43:35 (0) ** - ROOT/WEBADMINISTRATION, WebAdministrationProvider ({84951D16-922E-4692-B4E9-90DD80426ECF}) (i.e. WMI Class 'SiteContainsConfigurationSection')
53063 22:43:35 (0) **   Provider DLL: ''
53064 22:43:35 (0) ** - ROOT/MICROSOFT/WINDOWS/REMOTEACCESS/SERVER, RAServerPSProvider ({BEF7FC3B-203F-4AD6-B38E-A1F519202644})
53065 22:43:35 (0) **   Provider DLL: ''
The WMIDiag provider CSV shows that the RASERVERPSPROVIDER.DLL has no DCOM (WMI Provider Binary) registration. (see example below)
WMI Namespace
WMI Class name
WMI Provider Name
WMI Provider Model
WMI provider binary
WMI provider registration MOF file(s)
ROOT/MICROSOFT/WINDOWS/REMOTEACCESS/SERVER
PS_RemoteAccessLocal
RAServerPSProvider
No DCOM registry registration
No DCOM registry registration
C:\WINDOWS\SYSTEM32\WBEM\RASERVERPSPROVIDER.MOF
So I've tried to reregister the DLLs with regsvr32 RASERVERPSPROVIDER.DLL. I've also tried to recompile the MOFs (RASERVERPSPROVIDER.MOF). I found the missing DLL and MOF using WMIDiag on Another Server Essentials 2012 R2 machine. But no sucess - the WMI
Provider binaries and model are still missing..
Example from another (healty) 2012 R2 Essentials Server
WMI Namespace
WMI Class name
WMI Provider Name
WMI Provider Model
WMI provider binary
WMI provider registration MOF file(s)
ROOT/MICROSOFT/WINDOWS/REMOTEACCESS/SERVER
PS_RemoteAccessLocal
RAServerPSProvider
In-proc
C:\WINDOWS\SYSTEM32\WBEM\RASERVERPSPROVIDER.DLL
C:\WINDOWS\SYSTEM32\WBEM\RASERVERPSPROVIDER.MOF
Is there any other way to add the WMI provider binary manually? Or do you think I'm on the wrong track?
Thank you in advance.
Regards
Josef
Support Engineer
(MCP) Microsoft Certified Professional
(MCTS) Exchange Server 2010, Configuring
(CCNA) Cisco Certified Network Associate

Hi,
Here is a good blog to troubleshoot WMI issues.
WMI: Rebuilding the WMI Repository
http://blogs.technet.com/b/askperf/archive/2009/04/13/wmi-rebuilding-the-wmi-repository.aspx
First, I want to confirm if the good system is at the same hotfix/SP.
Re-register all of the dlls and recompile the .mofs in the wbem folder and re-registering WMI Service and Provider. Then verify the consistence of the repository.
If the issue persists, we can choose to rebuild the repository.
Hope this helps.

I have an iphone 5 with ios 6. I am trying to setup a new exchange email account. I need the backslash but it is not available. I can find it on other apps but not when trying to set up the mail account. (it is not on the keyboard)

I have an iphone 4s with ios 6. I am trying to setup a new exchange email account. I need the back slash but it does not show up on the keyboard. I know it is supposed to be on the +key (and is for other apps) but for some reason it is not available when setting up an email account. Is this on purpose or am I doing something wrong?

I can tell you that with Sprint their coverage area isn't as good as Verizon or AT&T.
Are you sending these imessage while on wifi or cellular data? Also your husband would need to be in a good coverage area.
Usually when imessage is unavailable it will send it as a text. Does your husband receive your imessage as a text?

I am trying to setup wireless using my old dome Airport ExtremeBase station. I had previously used it about 5 years ago when I had dial up but have now switche to DSL with Windstream. I can not get connecte as ABS keeps trying to dial up(the phone number)

I am trying to setup wireless using my old dome Airport Extreme Base station. I had previously used it about 5 years ago when I had dial up but have now switched to DSL with Windstream. I can not get connected as the ABS keeps trying to dial up(the old phone number). When I tried to change my network settings an annoying popup window says "your network settings have been changed by another application'. I have no idea what the message is all about and when I close this window it immediately pops up again and prevents me -as far as I can tell -from changing my Airport settings? I need advice on how to get this wireless setup done. Maybe a reset? or something else? I have the DSL phone line plugged into WIndsteam Seimens Speedstream 4200 modem and then the ethernet (yellow) wire from the WIndsteam Seimens Speedstream 4200 modem to the port on the dome that is a circle of dots.

1)Can you explain how using the AEBS as a bridge will work with the Seimens Speedstream4200?
As a bridge, the AEBS will basically become a wireless access point. This will allow the AEBS to provide a wireless network, but still allow the Speedstream to provide NAT & DHCP services for the wireless clients connected to the AEBS. If the AEBS was left as a router, you would have a double-NAT condition which isn't necessary bad in itself, but would create a second subnet. That would make it more difficult for clients connected to the AEBS to access clients connected to the Speedstream.
2) Is there a link that will guide me through the steps to set the AEBS as a bridge?
You can easily reconfigure the AEBS as a bridge using the AirPort Utility.
ref: AirPort Utility > Select the AEBS > Manual Setup > Internet > Internet Connection > Connection Sharing = Off (Bridge Mode)
3)Can I just connect the DSL phone line to the AEBS and eliminate the Speedstream4200?
Unfortunately no. The AEBS does not have a built-in DSL modem. You will still need the Speedstream to provide this function.

I am trying to setup iCal syncing with Mobile Me on Mac Pro and Mac Pro Notebook. I have accounts added in for MobileMe and Gmail. Problem is that iCal does not appear as one of the Sync choices in the MobileMe sync window on either computer?

I am trying to sync iCal with all my computers and devices via MobileMe. I cannot sync iCal on my Mac Pro nor Mackbook Pro. I believe accounts to be setup properly BUT on both computers there is NO choice to select iCal among the choices in "Sync Menu" on the MobileMe window in System Preferences. Help?

Greetings,
If you delete individual messages they will be deleted from other accounts.
If you setup the accounts as IMAP (which is the default for MobileMe accounts) you can remove the accounts and the other users will still have the email.
Alternatively if you don't want to see the account in the other user go to Mail > Preferences > Accounts > MobileMe account > Advanced > remove the check mark for "enable account". This leaves the account and just turns it off so you don't see it and it doesn't send / receive messages.
Finally, you should be backing up your data for safekeeping so even if you did delete the account and the messages magically vanished you could restore them: http://support.apple.com/kb/HT1553
Hope that helps.

HT1926 when trying to setup itunes on my pc i get the following message: there is a problem with this Windows installer package. A program required for this install to complete could not be run. How could I solve this problem?

when trying to setup itunes on my pc i get the following message: there is a problem with this Windows installer package. A program required for this install to complete could not be run. How could I solve this problem?

Repair your Apple software update.
Go to START/ALL PROGRAMS/Apple Software Update. If it offers you a newer version of Apple Software Update, do it but Deselect any other software offered at the same time. Once done, try another iTunes install
If you don't find ASU, go to Control Panel:
START/CONTROL PANEL/Programs n Features/highlight ASU and click REPAIR,

While trying to setup a time capsule backup to my MyBookLive external drive, I got the following error message: The network backup disk does not support the required AFP features. What's up with this?

While trying to setup a time capsule backup to my MyBookLive external drive, I got the following error message: The network backup disk does not support the required AFP features. What's up with this?

This means that your NAS does not support the required encryption. Update your NAS to the latest firmware or ditch it and buy a Time Capsule (they are the most reliable when using TM).

Trying to setup RAID 1 with new SATA drives on xserve 2009 model

Trying to setup RAID 1 with new SATA drives on xserve 2009 model
I have an Xserve rack mount model Xserve 2.26 Quad Core (EMC# 2279) with an Apple RAID card, 24GB RAM (running 10.9 Server software)
Purchased two Western Digital 1TB SATA III 7200 RPM 64MB Cache Black WD1003FZEX drives
It came with three 160GB SATA drives. I'm leaving one of the original 160GB drives for the OS, but I want to replace the 2 other drives and set it up with RAID 1 (mirrored). I bought 2 brand new Western Digital 1TB SATA drives and formatted them on another Mac through Disk Utility with Mac OS Extended (Journaled) formatting. I then placed the new drives in the Xserve and booted it up. After I login it immediately gives me 2 error windows saying...
"Apple RAID Card
The Apple RAID Card installed in your system requires your attention."
It has two buttons underneath this message allowing me to either select 'Ignore' or 'Open RAID Utility'
I've tried to RAID the drives the Disk Utility and through the RAID Utility with no success.
I have both drives mounted on the desktop, as separate drives, but I really need to set these up as a RAID 1.
I've been reading other forums, where others have been able to get this to work by using a jumper on certain pins (5 & 6)of the drive to back down the transfer rate to 1.5 Gb per second. I tried that and it didn't work for me. Maybe I used the wrong pins -- I just don't know. I'm also wondering if there is some Apple firmware that is required on these drives? I'm asking for help from anyone who has gone through this same issue. Thanks in advance.

UPDATE -- I had an issue with the RAID card battery, it was dead and I have since replaced it. But I am still unable to setup the RAID 1 drive configuration. Does anyone know if it has something to do with the faster transfer rates on these new drives. Maybe they need to be clocked down with certain jumper settings on these Western Digital drives? Or am I fighting a losing battle because these drives don't have Apple firmware? Any help would be appreciated. Thanks.

Trying to setup my new ATV and it won't set date and time, and won't allow me to log in with my apple ID.

Trying to setup my new ATV and it won't set date and time, and won't allow me to log in with my apple ID to homeshare OR to test te network, which I know is correct since I changed it. I live in an apartment complex and the router is in my roommates room. ANY suggestions? I'm at the point where I may return this because it has been nothing but a hassle. I'm very annoyed and just want the product that I paid for to actually work.
The ABOUT section says Network Time: Skipped (reachable) and Activation: Failed (skipped)
I'm also using my MacBook Pro as the homesharing with iTunes up to date.

I had a similar issue wuth my new Apple TV. If you (or your roommate) are able to change the router firewall settings, do that first. I don't know the ports that you need, except that 123 is one of them (to set the time). Then restart the Apple TV. See if that will get you through the activation process. I actually ended up restoring mine to factory settings, but I'm not sure if that step was really necessary.
I understand your frustration, though. Getting the Apple TV to work was such a pain -- it almost feels like it is not really an Apple product.

Trying to setup PHP site (friendica) with nginx on localhost

Hi, just new here :-)
Started to use Arch a couple of month ago and sofar everything went fine thanks to the great documentation!
Now I tried to setup friendica on my computer for testing some modifications but I just fail on installing the required modules :-(
I already installed:
php
php-fpm
php-gd
php-cgi
php-mcrypt
mariadb
nginx
phpmyadmin
But I still get the following errors:
GD graphics PHP module (required)
Error: GD graphics PHP module with JPEG support required but not installed.
OpenSSL PHP module (required)
Error: openssl PHP module required but not installed.
mysqli PHP module (required)
Error: mysqli PHP module required but not installed.
Generate encryption keys (required)
Error: the "openssl_pkey_new" function on this system is not able to generate encryption keys
If running under Windows, please see "http://www.php.net/manual/en/openssl.installation.php".
Command line PHP
Could not find a command line version of PHP in the web server PATH.
If you don't have a command line version of PHP installed on server, you will not be able to run background polling via cron. See 'Activating scheduled tasks'
PHP executable path Enter full path to php executable. You can leave this blank to continue the installation.
Url rewrite is working (required)
Url rewrite in .htaccess is not working. Check your server configuration.
My nginx.conf looks like this:
#user http;
worker_processes 1;
error_log logs/error.log;
#error_log logs/error.log notice;
#error_log logs/error.log info;
#pid logs/nginx.pid;
events {
worker_connections 1024;
http {
include mime.types;
default_type application/octet-stream;
#log_format main '$remote_addr - $remote_user [$time_local] "$request" '
# '$status $body_bytes_sent "$http_referer" '
# '"$http_user_agent" "$http_x_forwarded_for"';
#access_log logs/access.log main;
sendfile on;
keepalive_timeout 15;
gzip on;
gzip_comp_level 1;
server {
listen 80;
server_name localhost;
location ~ \.php {
root /srv/http/project;
fastcgi_pass unix:/var/run/php-fpm/php-fpm.sock;
fastcgi_index index.php;
fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name;
include fastcgi_params;
location / {
root /srv/http/project;
index index.php;
Can someone help me?

Thanks for the quick answer!
progandy wrote:Did you enable all necessary modules in your php.ini?
I had a look at /etc/php/php.ini but I can't find things (with my knwoledge) that seem to be important....
progandy wrote:Then you'll have to create the rules in the .htaccess in the format nginx understands.
Haven't checked that yet...
progandy wrote:https://github.com/friendica/friendica/ … tall-Guide
This is quite complicated. Seems like I'd need to study to understand it:-(
progandy wrote:http://jcsesecuneta.com/tome/labox/sett … -on-nginx/
This one seemed clear I changed my nginx.xonf according to it:
server {
listen 80;
server_name localhost;
root /srv/http/project;
access_log off; # If you are using 'Analytics' type software for tracking, keep this 'off'
log_not_found on; # Turn on if you want to track "not found" errors
error_log /srv/http/project/logs/error.log info; # valid values: debug, info, notice, warn, error, crit
#rewrite_log on; # Uncomment if you want to debug your rewrites (then change 'crit' above to 'notice')
# block stuff early
# Do not log favicon.ico and robots.txt stuff
location ~* /(favicon\.ico|robots\.txt) {
allow all;
access_log off;
log_not_found off;
# Return error 444 for these files
location ~* ^.+\.(bzr|git|log)$ {
access_log off;
log_not_found off;
return 444;
# Deny public access to ~ (bak) files
location ~* ~$ {
access_log off;
log_not_found off;
return 444;
# Friendica #
location / {
try_files $uri $uri/ @friendicacleanurl;
location @friendicacleanurl {
rewrite ^/(.*) /index.php?q=$uri last;
break;
# Security: Friendica #
# block public access to .htaccess and .htconfig.php
location ~* /\.ht {
access_log off;
log_not_found off;
return 444;
# block public access to .tpl files located in /view/ folder
location ~* /view/(.*)\.tpl$ {
access_log off;
log_not_found off;
return 444;
# block public access to /util/ folder
location ^~ /util/ {
access_log off;
log_not_found off;
return 444;
# Deliver static files directly #
# images (Friendica)
location ~* /(addon|images|library|spec|util|view)/(.*)\.(bmp|cur|gif|ico|j2k|jp2|jpe|jpeg|jpf|jpg|jpm|jpx|mj2|mng|png|svg|svgz|thm|tif|tiff|webp)$ {
add_header Pragma "public";
add_header Cache-Control "public";
access_log off;
log_not_found off;
expires 28d;
# redirect 50x error pages #
error_page 500 502 503 504 /50x.html;
location = /50x.html {
root /usr/share/nginx/html;
internal;
# enable PHP #
location ~ \.php$ {
try_files $uri =404;
fastcgi_split_path_info ^(.+\.php)(.*)$;
fastcgi_pass 127.0.0.1:9000; # Comment if you want to use sock instead of tcp
#fastcgi_pass unix:/var/run/php-fpm.sock; # Uncomment to use sock instead of tcp
fastcgi_index index.php;
fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name;
include /etc/nginx/fastcgi_params;
but then nothing works anymore! When I try to restart nginx I get:
sudo systemctl status nginx.service
nginx.service - A high performance web server and a reverse proxy server
Loaded: loaded (/usr/lib/systemd/system/nginx.service; enabled)
Active: active (running) (Result: exit-code) since Sa 2013-12-28 18:05:13 CET; 1 day 22h ago
Process: 15591 ExecReload=/usr/bin/nginx -g pid /run/nginx.pid; daemon on; master_process on; -s reload (code=exited, status=1/FAILURE)
Process: 318 ExecStart=/usr/bin/nginx -g pid /run/nginx.pid; daemon on; master_process on; (code=exited, status=0/SUCCESS)
Process: 314 ExecStartPre=/usr/bin/nginx -t -q -g pid /run/nginx.pid; daemon on; master_process on; (code=exited, status=0/SUCCESS)
Main PID: 320 (nginx)
CGroup: /system.slice/nginx.service
├─ 320 nginx: master process /usr/bin/nginx -g pid /run/nginx.pid; daemon on; master_process on;
└─10295 nginx: worker process
Dez 30 14:59:10 thinker nginx[10294]: 2013/12/30 14:59:10 [notice] 10294#0: signal process started
Dez 30 14:59:10 thinker systemd[1]: Reloaded A high performance web server and a reverse proxy server.
Dez 30 16:12:58 thinker systemd[1]: Reloading A high performance web server and a reverse proxy server.
Dez 30 16:12:58 thinker nginx[15396]: 2013/12/30 16:12:58 [emerg] 15396#0: "server" directive is not allowed here in /etc/nginx/nginx.conf:1
Dez 30 16:12:58 thinker systemd[1]: nginx.service: control process exited, code=exited status=1
Dez 30 16:12:58 thinker systemd[1]: Reload failed for A high performance web server and a reverse proxy server.
Dez 30 16:15:33 thinker systemd[1]: Reloading A high performance web server and a reverse proxy server.
Dez 30 16:15:33 thinker nginx[15591]: 2013/12/30 16:15:33 [emerg] 15591#0: no "events" section in configuration
Dez 30 16:15:33 thinker systemd[1]: nginx.service: control process exited, code=exited status=1
Dez 30 16:15:33 thinker systemd[1]: Reload failed for A high performance web server and a reverse proxy server.
What's wrong?

I am trying to setup VPN with QuickVPN

Similar Messages

Maybe you are looking for