I am unable to join my existing wireless network with new AirPort Express

I am unable to join my existing wireless network with new AirPort Express.
I am using a DLink DI-524 Router, Windows 7 (64), and the AirPort Express.
AirPort Utility will not recognize the AEX wirelessly, it will only recognize it when it is connected by Ethernet. I can then configure the AEX and verify that the settings stick once disconnected and then reconnected. However, even after that, it will not recognize the AEX once disconnected from the Ethernet cable.
I followed the suggestions of several other threads on these forums. But I am unable to get the AEX to work.
Any suggestions? Thanks in advance.

Welcome to the discussion area!
It's almost always a security setting that causes problems when the Airport Express (AX) tries to join a third party wireless network. The AX usually does not "join" correctly and that's why you can't see it on your wireless network using AirPort Utility.
Using an ethernet cable is still the more reliable way to configure and adjust the AX, but if you are want to try to configure it using wireless, you must return the AX back to factory defaults as follows:
Power down the AX
Hold in the reset button +and keep holding it in+ as you plug the AX back in to power
Release the reset button after 10 seconds
When it is set to factory defaults, the AX broadcasts a wireless signal with a network name like "apple network xxxxxx" where the "x's" are either letters or numbers. You must look for this network by clicking on the fan shaped Airport icon at the top of the screen. If you don't see this network, then click Join Other Network to search that way. Unless you connect to this network, you will not be able to configure the AX using wireless.
Do you know the exact security type that your D-Link router is using? That is the key element in the process.
Open AirPort utility, click Manual Setup
Click the Base Station tab to establish a name for the AX, device password and adjust time zone settings
Click the Wireless tab
Wireless Mode....Join a wireless network
Wireless Network Name...must exactly match your D-Link wireless network name
Enable ethernet clients if you want the port to be active (your D-Link must be compatible with ProxySTA for this to work)
Wireless Security...exact setting of the D-Link network. WEP security causes a lot of issues. Try to use WPA/WPA2 Personal, which is far more secure.
Wireless Password...must match the D-Link network
Click the Music icon to enable AirTunes
Click Update to save settings
Any luck?

Similar Messages

Extending an existing wireless network with an airport express

My wireless signal is quite weak in my room so I'm looking for a way to extend the range of the network by using an airport express. I understand i can't do this wirelessly but is it possible to run an ethernet cable from my existing router to the airport express in my room and then have a stronger signal in my room?
Thanks in advance!

Welcome to the discussion area, Aaron!
If you connect an ethernet cable from your existing router to the AirPort Express, and then configure the Express to "Create a wireless network" with the same name, security settings and password, this will in effect, extend your current wireless network.
The Express must be configured as a "bridge" to operate correctly on your network when you do this, meaning that the setting for Connection Sharing on the Express will be set to "Off (Bridge Mode).

Unable to create a wireless network with my airport express. Please help!

I am trying to setup a wireless network with an airport express, and connect to it with my Macbook. I just bought both of these and haven't been able to get wireless to work.
I initially plugged the ethernet cable from my cable modem into the airport express and plugged it into the wall. The macbook detected it when I opened airport utility, but the express had a flashing amber light and I was unable to connect. I then unplugged the express and re-started the cable modem. This time, the airport express showed a solid green light -which should mean that it is working correctly. However, the macbook did not find the airport express device when i searched for it using airport utility. I am able to connect the macbook directly to the cable modem, after re-starting the modem, and access the internet so at least some of the systems are go.
Any ideas? Thanks in advance for your help.
Tom

Is the issue that you cannot access the 802.11n AirPort Express Base Station (AXn) with the AirPort Utility that is running on your Win7 PC? ... or that once you have configured the AXn, the PC is unable either to find the new wireless network or can find it but cannot connect to it?

I am unable to join my own wifi network with new iphone 5

I am unable to join my own wifi network with new iphone 5. It has the latest software downloaded too. Keeps saying unable to join network after I type in the password. All my other devices are able to join but just not the iphone. I've called Verizon and my internet provider and they have been unable to help. I had no problems with my iphone 4 with this very same issue. Please help or I'll be forced to return this phone. I have 13 days left.

Try power-cycling your router (unplug for 15 seconds, then plug back in), then on your phone go to Settings>General>Reset and tap Reset Network Settings, and try joining your network again. Note: resetting network settings will erase passwords for previously joined networks on your phone.

Joining an existing wireless network with airport express

Ok, am almost to the point of throwing my AX across the room
AM trying to join an existing wireless network, its from a 2Wire gateway
one of three things happen
it won't find the AX in the first place
it recognizes it, but i can't connect to it
it goes through the configuration and when it restarts the AX, it can't reconnect to either the router or the AX and it fails. if this happens i can't reconnect to my wireless network without deleting it and re-adding.
it doesn't show up in my available wireless networks at all
protected via WEP, and i have tried using all the security options.

The directions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode.
Are you using MAC address access control in addition to WEP?
Turn off WEP and see if that makes a difference?
One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
Though sometimes not even that works and the HEX key must be used regardless.
Choosing a password for networks that use Wired Equivalent Privacy (WEP)
http://docs.info.apple.com/article.html?artnum=108058
WEP is now considered not to be secure and therefore it is advised you use WPA.
"WPA Personal" on the Mac corresponds to plain WPA, with a pre-shared key (PSK) and TKIP encryption, on non-Apple wireless routers. The same alphanumeric password should work on both.
iFelix

Can you expand an existing wireless network with the airport?

Can you use an Airport Extreme to wirelessly expand an existing wireless network?

Yes you can, only if the primary base is an airport extreme, airport express or time capsule

How to extend range of my wireless network with an Airport Express connected by ethernet with Airport Utility 6.0

Hi everyone,
I have AirPort Express 802.11n (1st Gen) firmware 7.6.1, that is connected to my main wifi base station (a TimeCapsule) by ethernet. I would like to extend the range of the Wifi Network but am not clear on how to do so using the new interface of Airport Utlity 6.0.
Does anyone have any tips on how to do this?
BR
AK

Hi Everyone!
Many thanks for the tips. I have downloaded 5.6 and have set my Airport Express in the "Extend a wireless network" mode. I was still having a few problems with the quality of the wifi connection in different parts of my apartment (by no means a very large one, but walls seem to be made of extra dense concrete here in Singapore) and went out and bought a few powerline adapters by TP Link (http://www.tp-link.sg/products/details/?categoryid=1862&model=TL-PA211#spec).
If you don't mind a slightly long post, I would be very grateful for any tips:
My setup is now as follows:
Main room
Time Capsule - connected to a Cisco DPC3925 Modem (http://www.cisco.com/web/consumer/support/modem_DPC3925.html) both connected to a TP Link adapter 1.
iMac - connected via Ethernet to TP Link adapter 2 and wifi enabled
Airport Express 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1) used to stream audio to a stereo that doesn't have an optical cable input. Since it is an Ethernet connection, I have wifi turned off.
Apple TV 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1)
Bedroom A
Airport Express 2 - connected via ethernet to TP Link adapter 3
Bedroom B -
Apple TV 2 - connected by Ethernet to a TP Link adapter 4
After following the tips on setting up the extended wifi network, I find that when I use a wireless client (e.g. iPad, Macbook air, etc) in either Bedroom B or Bedroom C (both don't have wifi in the room) the connection is very poor. Even more odd is that the connection in Bedroom A, one that does have Airport Express 2. To be clear when I mean very poor, I mean Skype/facetime skips frames and freezes... this doesn't happen when I am in the main living area.
I would be very grateful for tips on how to set up the most robust network given the configuration above. Specifically, I am wondering about:
When I select Extend a wireless network option on Airport Utility 5.6 the summary page states that it is connecting using "Wireless Network" vs what I would expect it to say "Ethernet connection".
Is there any advice on whether to enable 5Ghz network and if so, should I try to use that for the various wifi clients?
Does anyone know if I can somehow use Apple products to extend the reach of the Cisco DPC3925? Frustratingly the signal is quite strong (compared to Apple routers), but I cannot properly stream audio/video if that wifi network is used (as my iMac that hosts the content is on the Apple one... and I'd have to walk over to switch it to the Cisco one).
Any other tips would be much appreciated!
Cheers!
AK

Unable to extend existing wireless network with new TC

I have an original 500GB Time Capsule that I've been using successfully for a long time. It is plugged into my modem/router (which acts as a DHCP server) in bridge mode.
As the TC is getting full (and the number of Macs in our house is increasing!), I decided to buy another TC - this time the latest 2TB model. I have set it up so it extends my existing network. However, as soon as I plug it into my network my Internet connection breaks (or goes very slow) and the modem/router activity light flashes like crazy. As soon as I unplug the new TC from my wired network, I get my fast Internet connection back and the modem/router goes back to normal.
I've tried using the LAN and WAN ports on the new TC to connect to my wired network but the result is the same.
Has anyone any ideas what the problem is? Is there a problem using the latest TC to extend the wireless network of an older model TC?

Welcome to the discussion area!
If you are connecting your Time Capsules using an ethernet cable, you would connect from one of the LAN ports on the "main" device to the WAN port on your new 2TB device.
The 2 TB device must be configured as a "bridge".
You would configure the 2 TB device to "create a wireless network" using the same network name (SSID), security setting and password as your "main" device. (The "extend" setting is only used if you are connecting your devices using wireless only...and you are using ethernet).
When you "create" the wireless network on your 2 TB device, you are configuring what is known as a "roaming" network. Your laptop will automatically connect the device with the strongest wireless signal depending on where it "roams".
To configure your 2 TB device as a bridge:
AirPort Utility > Manual Setup > Internet icon > Connection Sharing setting = Off (Bridge Mode).
Please post back on your results.

Extending airport express wireless network with another airport express

I am trying to set up another airport express to my existing airport express at home so I can extend the wireless range and also to connect my printer (to my second airport express) so I can have a shared wireless printer. Is this possible? If so, can someone assist me on how to set this up?
Thanks.

Try the following ...
AirPort Express Base Station (AX) - WDS Setup
"Factory Reset" the AX base stations
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
(Note: To facilitate setting up the base stations, place them in near proximity of each other during the setup phase. Also record the Apple IDs of each base station that will included in the WDS as these will be required during setup.)
Main Base Station Setup
(Note: The AX connected to the Internet will be assumed to be the main base station in the WDS.)
Either connect to the AX's wireless network or by temporarily connecting directly, using an Ethernet cable, to the Ethernet port of the AX, and then use the AirPort Admin Utility to make the following settings.
WDS Tab
1. Enable this base station as a WDS: main base station (checked)
2. Allow wireless clients on this base station (checked)
3. Click "+" to add Remote/Relay Base Stations.
3a. Select the Base Station that you want to be the WDS Remote/Relay.
3b. AirPort ID: <verify that this is the correct MAC address for the Base Station you are adding as a Remote/Relay.>
3c. Auto configure as a WDS remote base station (checked)
3d. Click "OK."
4. Verify that the Remote/Relay Base Station has been added to the list.
5. Click "Update," and then verify the settings for the Remote/Relay.
5a. Allow wireless clients on this base station (checked)
5b. New network name: <verify that this is the same as the network name as the main base station>
5c. TCP/IP: Configure using DHCP
5d. Base Station Password: <the Remote/Relay Base Station password>
5e. Confirm: <same as previous step>
5f. Click "OK."

Having trouble with extending an Apple wireless network with a AirPort Express

Trying to extend the range of my AirExtreme with a AirExpress:
I get stuck when the AirPort Utility ask is I'm sure I want to switch networks. if I select switch I loose the AirExtreme. If I select don't switch it take me back to the beginning. Any help will be appreciated.

You have to "switch" networks to be able to pick up the signal from the Express and configure it with new settings.
Once the Express is configured it will become part your existing network when you see a green light.
Then, switch back to your regular wireless network on your Mac and everything will be on the same network

I have an airport extreme and am trying to extend the range of the wireless network with an airport express. I set it up with the help of apple support, both lights are green on both airports, but the range didn't change. What could be wrong?

I am trying to extend the range of my wireless network by adding an airport express to an airport extreme. I configured it with the help of apple support, but it hasn't changed the range that I can access the internet wirelessly in my house. What could be the problem? Does weather affect the wireless network??

So, on the Extreme you checked the box to "allow this network to be extened" ?
Correct?
And on the Express, you set it up to "Extend a wireless network" ?
Correct?
See this Apple article and see if you missed anything...
http://support.apple.com/kb/HT4145
To learn about other options for expanding your Wi-Fi base station wireless network and things you should consider before expanding your network, click here.
Set up: Components of an extended network
➊ Primary Wi-Fi base station (this is the base station connected directly to the Internet)
➋ Extended base station
Configuring a wireless extended network
To create a wireless extended network, you must place any extended Wi-Fi base stations within range of the primary Wi-Fi base station.
Start with the device that will be configured as the primary Wi-Fi base station. Then configure your extended Wi-Fi base stations, ensuring that each is within direct range of the primary Wi-Fi base station.The physical location of extended Wi-Fi base stations will vary according to the building environment and may require some experimentation.
If you have configured your Wi-Fi base stations in the past, it may be helpful to do a factory default reset of each Wi-Fi base station that will be part of the wireless extended network before you begin.

Extend wireless network with multiple airport express and netgear powerline

I currently have the following network configuration:
1. Using ATT u-verse (2-wire 3800HGV-B "modem") to internet
2. Disabled the u-verse modem wireless router, and have connected an Apple Time Capsule wireless router (on a DMZ)
3. Have four Netgear XAVB5001 powerline adapters connected to the time capsule (for our iMac desktops and the Apple TV)
4. Have an Airport Express wirelessly connected to the time capsule to extend range (for our iPhones and iPad)
All this is currently working. What I would like to do is the following, keeping 1-3 above the same:
4. Connect the airport express to the time capsule via Netgear XAVB5101 powerline adapter (instead of wirelessly connecting to the time capsule as it is today) and use it to extend the wireless range of the time capsule
5. Add ANOTHER airport express to the time capsule via powerline adapter (and extend the wireless range elsewhere in the house).
Does anyone have any experience with this kind of setup and can assure that it would work? (I'm trying to decide whether to spring for a couple more powerline adapters and another airport express)
Thanks in advance!
Dave

I had a VERY similar problem: I was trying to extend my wireless network using a hardwired ethernet connection from Airport Extreme to my Time Capsule. Every time I plugged in the wire to the TC, everything disappeared. Unplugged, and boom. Came back.
Here's how I solved it:
Go into Airport Utility and select the unit you are trying to use as a wireless extender and choose to edit it. Then, on the wireless tab select CREATE a wireless network. But, give it the exact same name and password. This is completely counter-intuitive. You would think to choose EXTEND, but this would be wrong. Next choose the network tab. And, select Router mode to Bridge (off).
By choosing the same name and password, your phone, laptop, etc. will think it's on the same network and move seamlessly from one to the other.
See if this fixes your issue. Fixed mine instantly. AND, it only took 3 painstaking hours of checking ethernet connections and rewiring jacks, etc. to figure it out. LOL

How do I extend a netgear wireless network with an Airport Express?

I can get the Airport Express to join the network, but not extend it. I am trying to extend my network to improve the signal to my Apple TV. I have read in some places that his can't happen. I have a Mac as my computer.

Any idea how to merge the Netgear extender to the primary Netgear network?
You have a question for Netgear Support here since your question involves two Netgear products.
This link would be a logical place to start:
Contact Support - Netgear
While it is possible that someone on an Apple forum might know how to do this....it is also unlikely that they will see this post and respond. You can certainly wait to see if someone responds here if you wish.....but if it were me, I would contact Netgear about a Netgear question.

Extend existing wireless network with airport express..impossible?

I have tried to extend my existing wireless network with an airport express, but it seemd that I always need a ethernetcable...apple support insured me it is possible but the airport utility software only allows me to extend using a cable it seems....

Couple of thoughts here.......
The AirPort Express will only extend a wireless network if you have another Apple router providing the wireless network to be extended.
Is your "main" wireless router an Apple product? If yes, what model number do you have?
It would also help if we could get the model number of the AirPort Express. Some older versions are not capable of extending a wireless network.

I have a mid-2010 iMac and just purchased a 2TB TC, can't join existing wireless network with AC standard so attached to iMac via ethernet with TC wifi turned off. How do i access TC now? not showing up in disk utility or on desktop. working fine with TM

I have a mid-2010 iMac and just purchased a 2TB TC, I just found out that it can't join existing wireless network with new AC standard so attached to iMac via ethernet with TC's wifi turned off. How do i access TC now? not showing up in disk utility or on desktop. It is working fine with TM. My cheeper seagate drives etc kept crashing, so i didnt trust cheeper back up options anymore. Connected those drives to TM via firewire and could see the drives and access them.
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc. I connect to the internet via airport only and it is pretty fast. Getting over 50mbs downloads and over 30mbs uploads. Plus everything in my home it connected to my fios router, airport express for music streaming, two apple tvs, vuezone camer system. I really didn't want to monkey around too much with my system. But are there other options to connect the new TC. Can't find info anywhere for this and called apple who gave me the info above. after hanging up, i see that i cant access my TC and I am wondering if i would have to reset it to turn wifi on again to make changes to the drive, turn off blinking light or repair it in disk utility if it should become corrupted.
For other with similar issues i did solve some other problems: when i connected it to my ethernet port on my iMac wifi stopped working. Found that I had to turn off the ethernet in the system>network screen, but then TM didn't see the TC so i restarted after changes and then it saw it.
Now a rant. I can't believe in this wireless age that Apple would make a product that cant join a wireless net work. The apple rep said i could return it and look for the previous TC that would join an existing wireless network. Are we going backwards?
Thanks!
lennydas

Ok... it is getting a bit clearer but there are still some questions.
I connect to the internet via airport only and it is pretty fast.
I was assuming airport in this statement in your first post meant the TC or the Express.. but I now realise we are still in the mass confusion stage where apple calls everything wireless an airport. So what you mean is the airport internal card of the computer??
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc.
I think this is mistaken.
Putting the TC in bridge mode plugged into your FIOS will not slow the network.. nor will it cause mail or port issues.. in bridge the TC is just a fancy WAP and switch plus the network hard drive.
If the computer is close it will be faster than the FIOS.
You can run both wireless networks with different names.. so it is clear which is which. But you can also setup roaming so the computers themselves pick which is the best wireless.
I tried extending the wireless net work and tried joining wireless network, but the TC kept crashing and I had to keep resetting the TC. the Apple support person said these, extend wireless network and joint wireless network, are no longer a connection option with the new TC because of the new AC protocol.
Thanks again!
You cannot extend to a non-apple wireless router.
You cannot use join a wireless network because when you do the ethernet ports will be cut off.
But that has not changed.. I don't think Apple support is correct.. there has been no change with the AC model.. it is simply a fact that apple routers do not work in join wireless mode other than as a dumb client. The same applies to AC as to the earlier version.. but I have asked another person to check this.
Join in the express is the only apple router that still allows an ethernet connection.
For now you best use of the TC is bridged to the FIOS. Wireless you can sort out between several options.

I am unable to join my existing wireless network with new AirPort Express

Similar Messages

Maybe you are looking for