I am using datasocket in seperate vi, with error catching, but network slowdown causes labview to crash without any error message ...

I have a master computer setup as a datasocket server with several vi's that publish. I have about 5 other computers each with a vi that reads the data socket publisher. The interval at which the 5 vi's read is every 15 minutes, concurrently. It seems that when ever there is a network slow down, LabVIEW crashes catastrophically, even though I have timeouts in the datasocket readers. Is this error related to the datasockets not being able to handle the slow down or something else? Should I use another technique - if so - which is more reliable (FTP, TCP/IP?). This bug has been hounding me for several MONTHS.

One thing I forgot to mention - the 5 datasocket readers are also web servers, serving out the front panels to the web after getting updated. Well, after weeks of trial and error, would you believe that if I turn off the web server logging, everything works fine. I have had it off for a week now and no crashes. I first discovered this by realizing that if I turned off the web server everything ran fine (which would be totally useless for my application), so then I searched this site and found an off the cuff remark about the web server logging function causing crashes for an unrelated problem. I figured what the heck, I'll disable it and see what happens. So far so good, I am still keeping my fingers crossed ...

Similar Messages

Can we use Apple tv to present with iPad wirelessly but no internet? if not, is there any other way?

Can we use Apple tv to present with iPad wirelessly but no internet? if not, is there any other way? Please tell me what's the best solution if I want to present what's on the iPad screen to TV or projector withtout using internet network or small range of bluetooth.

yes

How do I sync music onto 3 phones with different iclouds but one apple id and one laptop without any problems, each phone user wants different music???

I have recently uploaded some music onto my laptop from cds onto my itunes library. User 1 (B) is a regular user of itunes and has playlists on his iphone from cds. User 2 (c) wanted like a particular cd on his phone and it synced onto iphone ok from the itunes library, also has never used the laptop before to sync normally uses icloud.
User 1(b) later downloaded 5 cds onto itunes and wanted to sync onto iphone but now cannot get the sync to work, however when you ask what is actually on the phone those cds do feature via itunes but are shown in grey on the screen whereas all the other music on the phone is in black.
FACTs
I only have one laptop and one login on the laptop
All three phones have their own icloud
User 3(K) just uses icloud and doesn't use itunes on the laptop but occasionally buys tracks straight from itunes on her iphone
QUESTION
Does this mean only one user can login/sync to itunes?
What is the solution to this problem so that all 3 users will be able to log on to itunes with the same login on the laptop to sync cds onto iphones?
Would Home Sharing help?
Thanks

You are going to need to change the email address you use with your old ID. Once you have got access to your old account you will then log into both accounts at the same time on your Mac and transfer your data to a single account. We can do this later, but need you to get access to your old account first.
My Apple ID

[DC2] An net use or LsaPolicy operation failed with error 67 - Moving AD from 2003R2 to Server 2012

Hello, i hope someone can help me with this tricky situation.
The plan is to move AD from 2003R2 name "DC" to a server 2012 "DC2"
I have made all the adjustments and transferred all the role to the new 2012 server, and both are now GC servers.
The problem is "transferring" the netlogon share.
in DCDIAg on the new server i get:
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
Home Server = DC2
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site-Name\DC2
Starting test: Connectivity
......................... DC2 passed test Connectivity
Doing primary tests
Testing server: Default-First-Site-Name\DC2
Starting test: Advertising
......................... DC2 passed test Advertising
Starting test: FrsEvent
There are warning or error events within the last 24 hours after the
SYSVOL has been shared. Failing SYSVOL replication problems may cause
Group Policy problems.
......................... DC2 passed test FrsEvent
Starting test: DFSREvent
......................... DC2 passed test DFSREvent
Starting test: SysVolCheck
......................... DC2 passed test SysVolCheck
Starting test: KccEvent
......................... DC2 passed test KccEvent
Starting test: KnowsOfRoleHolders
......................... DC2 passed test KnowsOfRoleHolders
Starting test: MachineAccount
......................... DC2 passed test MachineAccount
Starting test: NCSecDesc
......................... DC2 passed test NCSecDesc
Starting test: NetLogons
Unable to connect to the NETLOGON share! (\\DC2\netlogon)
[DC2] An net use or LsaPolicy operation failed with error 67,
The network name cannot be found..
......................... DC2 failed test NetLogons
Starting test: ObjectsReplicated
......................... DC2 passed test ObjectsReplicated
Starting test: Replications
......................... DC2 passed test Replications
Starting test: RidManager
......................... DC2 passed test RidManager
Starting test: Services
NtFrs Service is stopped on [DC2]
......................... DC2 failed test Services
Starting test: SystemLog
......................... DC2 passed test SystemLog
Starting test: VerifyReferences
......................... DC2 passed test VerifyReferences
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test
CrossRefValidation
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test
CrossRefValidation
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Running partition tests on : dom1
Starting test: CheckSDRefDom
......................... domain passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... domain passed test CrossRefValidation
Running enterprise tests on : domain.xxxxx.no
Starting test: LocatorCheck
......................... domain.xxxxx.no passed test LocatorCheck
Starting test: Intersite
......................... domain.xxxx.no passed test Intersite
I have as a last option the burflags issue, i tried this with the option D2, but i think i have done it wrong, because the netlogon share is gone on the old DC. i took a backup of the files and folders before
i did this. http://support.microsoft.com/kb/290762/en-us But i am a little confused on which server i am going to set the D4 value on now? COuld someone help? Best regards Aksel

Hello Dirk
And thank you for your answer, in regards of the KB, do i have to follow the steps regarding:
Global vs. replica set specific reinitialization
You can locate the replica set specific
BurFlags
registry key by determining the GUID for the replica set that you want to configure. To determine which GUID
corresponds to which replica set and configure a restore, follow these steps:
Click Start, and then click Run.
In the Open box, type cmd and then press ENTER.
In the Command box, type net stop ntfrs.
Click Start, and then click Run.
In the Open box, type regedit and then press ENTER.
To determine the GUID that represents the replica set that you want to configure, follow these steps:
Locate the following key in the registry:
KEY_LOCAL_MACHINE\System\CurrentControlSet\Services\NtFrs\Parameters\Replica Sets
Below the Replica Sets subkey, there are one or more subkeys that are identified by a GUID. In the left pane, click the GUID, and then in the right
pane note the Data that is listed for the Replica Set Root value. This file system path will indicate which replica set is represented by this GUID.
Repeat step 4 for each GUID that is listed below the Replica Sets
And so on?
I have only thos 2 DC's in the network...

If i lock my Mac using iCloud "Find My.." with a code, but now i have forgotten the code i used but have my Mac bac. How can i Unlock it????

If i lock my Mac using iCloud "Find My.." with a code, but now i have forgotten the code i used but have my Mac bac. How can i Unlock it????

If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup).
If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.
You may have to force iPad into Recovery Mode
http://support.apple.com/kb/ht1808

Just got new air and trying to set up. When I put in my Apple ID and password it comes up with error message 'can't sign in because of server error. Try again signing on.' Trying again does not fix. I know my ID and PW are right as work on other devices.

Just got new air and trying to set up. When I put in my Apple ID and password it comes up with error message 'can't sign in because of server error. Try again signing on.' Trying again does not fix. I know my ID and PW are right as work on other apple devices I have.

Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems
http://tinyurl.com/32drz3d
 Cheers, Tom

The way I deal with error message 1417, 1418 and 1428

Firstly, sorry for my poor English, but I would like to share with you my experience, and hope that it may helps you.
Since the release and update of iTunes 7, I have not faced any problem, but I heard a lot of articles from this forum about the errors 1417, 1418, 1428 and 50 etc. I could not make any suggestion and find a solution about it, all I could do is to copy some threads from some successful cases mentioned on this forum.
Until yesterday, I finally received a 4th Gen 20GB iPod (around 2 years old)from a friend and asked me whether I could fix it for him, which has been left untouched as a paper-weight for almost 2 months.
I tried to turn it on, and the screen was completed blank and the device looked dead. Before doing anything I prepared the following:-
1. A window based PC
2. A Mac computer
3. An USB iPod cable
4. A Firewire iPod cable
5. An iPod AC charger
As the iPod was previously formatted on a PC, therefore I tried to plug it with a PC via USB cable, it did not response and not able to get recognized by the PC. I ejected the iPod and connected with an AC charger, after a few minutes, I did a Reset for the iPod
How to reset iPod
http://docs.info.apple.com/article.html?artnum=61705
The iPod showed an Apple sign, it stuck there for almost a minute, the screen then showed a battery with an exclamation mark sign, and after a minute, the iPod turned off itself. I was sure that the iPod carried very low battery, and could not be charged by connecting it with any computer (both Mac and PC).
I decided to let it have a charge with an AC charger for a bit longer, after 10 minute I did the Reset again, this time a sign of folder with exclamation mark showed up after the Apple sign, and again could not get recognized by a computer.
I changed my mind, and put the iPod into disk mode
Putting iPod into disk mode
http://docs.info.apple.com/article.html?artnum=93651
Instead of connecting with a PC, I plug it with my Mac using a Firewire cable, it did not response, so I switched the cable to an USB, interestingly, the iPod got recognized and a window pop up indicating that the iPod needed to do a Restore. Therefore I clicked “Restore”, after a few seconds, an Error message pop-up with Error Message 1417, the sign that I have been waiting for quite sometime.
I ejected the iPod and the screen immediately showed a folder exclamation mark (a sign indicating a corrupted or a failure iPod OS). I am forced to put the iPod into disk mode again, connected with the Mac computer and open the Disk Utility
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
It managed to complete the Restore process, and started to sync with the iTunes. However, it got stuck at the song no.238 from the total of 2000. I left it for an hour, but with no process, instead the iPod became “Hot” and the iTunes showed an Error message of 1428. I ejected the iPod from my Mac computer, the iPod’s screen turn to show the famous killer icon;“The Sad iPod“.
This time it was totally dead, even failed to put it into Disk Mode and non of the computer could recognize it. Sigh, I hated to do it but I knew that I must did the following:-
Holding the iPod in my Palm, and hitting it on a surface of a Sofa with 5 attempts.
Did not surprise me, the iPod turned on and it showed the Language Menu on the screen. So, I put it into Disk Mode and connected with my window PC.
The PC showed a sign and indicated that an USB device had been connected with it. I opened the iTunes and did a Restore there.
However, an Error Message 50 showed up, but I were not worried about it, connected it back with my Mac computer with it in Disk Mode. As expected the iTunes opened and allowed me to do a Restore there.
This time it managed to complete the process and a window of register pop up. After the completed the process, the iPod started to sync with the iTunes again, which finally managed to complete the process.
I left it connecting with the AC charger overnight. In the next morning, I switched it on and have a play with it, I am so glad as it is working like a charm.
From the above experience, I would like to share it with the user the following:-
1. It always better to charge with an ac charger instead of the computer, as when an iPod carrying with very low battery, it may not able to get charge from a computer
2. Try to connect the iPod with a computer, switching between USB and Firewire
3. Try to format an iPod with HD problem, with a different kind of computer e.g. Mac or PC, as the formats are totally different, the way it formats may able to solve the bad sectors on the HD
4. It may get better chance to get your iPod recognized, if you put it in Disk Mode
I hope the following works in your case as I did.

a pop up error message says itunes couldnt be configured
I'd like to have a closer look at that error message please.
Generate the error message again. While the error message box is open, hold down the Alt key and hit the PrtSc key. Paste the screenshot into an image file (using a program like Paint), and save the file.
Start a reply here and click the wee camera icon at the top of the reply window. Click "Choose file", browse to the image file, select the file and click "Open". Now click "Insert file" to insert the screenshot into the reply.

Ipod touch is disabled with error message to login to Itunes. i log in and device is not recognized as it is disabled. Im stuck in a loop....???

My iPod touch is disabled with error message to log into ITunes. I log in to ITunes and it does not recognize device as ITouch is disabled. Im stuck in a loop...?
Any assistance is greatly appreciated.

Connect the device to your iTunes library in Recovery Mode using the instructions in this Apple support document. From there restore it factory defaults.
http://support.apple.com/kb/ht1808
B-rock

HT1925 After failed update of itunes yesterday, now will not run with error message "MSVCR80.dll can't be found, APSDaemon.exe not running". Windows 7.

After failed update of itunes yesterday, now will not run with error message "MSVCR80.dll not found" APSDaemon.exe will not run. itunes will not now run.

Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
Remove all of these items in the following order:
iTunes
Apple Software Update
Apple Mobile Device Support (if this won't uninstall move on to the next item)
Bonjour
Apple Application Support
Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
Please note:
Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
HT1925: Removing and Reinstalling iTunes for Windows XP
HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
tt2

Lightroom has crashed with error message 'error reading from its preview cache' - this happens every time i try a launch it. I have looked a forum to repair the fault. there are different recommedations.can you tell me step by step how to recify this pro

lightroom has crashed with error message 'error reading from its preview cache' - this happens every time i try a launch it. I have looked a forum to repair the fault. there are different recommedations.can you tell me step by step how to recify this problem. i can not find ircat ir data etc in the programme files. Thanks

robmac76 wrote:
can you tell me step by step how to recify this problem.
Yes:
Step 1: Delete the preview cache.
That's it!
So, the trick is to find the preview cache.
This document gives location:
http://helpx.adobe.com/lightroom/kb/preference-file-locations-lightroom-41.html
To be clear: it's a folder in with your catalog and you want to delete the whole folder but nothing else.
If your catalog file path is "X:\My Catalogs\My Catalog.lrcat", then the preview cache "folder" will be:
X:\My Catalogs\My Catalog Previews.lrdata
So the trick is to find your catalog file, and since Lr won't open your catalog and run, you can't use it to find out.
But you should be able to find it by searching your disks for *.lrcat files - do you know how to do that?
Which OS?
If you know the name of the catalog it will help, but also: it's probably NOT in with your program files.
UPDATE: The above-mentioned document gives default name and location for preview cache, so if you haven't overridden the default, it should be right where that document said it would be - is it? (of course you need to know your user name too, but presumably you do, no?).
R

I plug my ipod into my computer itunes pops up with error message "Ipod detected but can't be identified properly" suggests I unplug and try again or uninstall itunes and reinstall nothing works. What should i do?

I plug my ipod into my computer itunes pops up with error message "Ipod detected but can't be identified properly" suggests I unplug and try again or uninstall itunes and reinstall nothing works. What should i do?

summarizing:
iPod nano (what version iOS BEFORE update?)
downloaded music
updated iPod to iOS 8.1.2
Windows 7 PC
plug-in iPod to PC
error message from iTunes on the PC "Ipod detected but can't be identified properly" ⬅[quoted from your original post] (+ suggested troubleshooting steps)
un-plug > re-plug iPod (how many times?)
iTunes un-installed from PC (?)
iTunes RE-installed to PC (?)
error message repeats(?)
searched "Ipod detected but can't be identified properly" site:support.apple.com with ZERO results - pretty strange that the support site wouldn;t know an iTunes generated error message (?) EDIT - had an "aha! moment when using a fresh Google search page and 'suggested' CANNOT
then "Ipod detected but can't be identified properly" site:discussions.apple.com had ONE result = Can't connect to iTunes with ipod touch (-50 error) - NO REPLIES
CANNOT instead of can't [ tsk tsk ]
iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support
follow all the instructions in order and let us know

ITunes - When launched comes up with error message - User at wits end

Hi - When launched ITunes comes up with error message below
"iTunes has encountered a problem and needs to close. We are sorry for the inconvenience" - and then wants to send an error report off to Microsoft
I have so far been through the bulletins and - deleted high and low filters using regedit , disabled virtual drives (which bought me CD drive back to life hurrah), reinstalled several times both Quick Time and I Tunes (seperately and together) including using Windows Install Clean up and the methodical Uninstalling and full deletion of Files - HELP - any ideas !! - forgot also disabled Norton through these steps

Try this, it took me 5 days but I eventually got it to work.
1. Scanned my hard drive for viruses. 1 was found & fixed, Spybot search and destroy, this is a freebee of the internet. Reboot PC
2. Removed all software having to do with quick
player & itunes - including ipod updates. Reboot PC
3. Downloaded Quick player via the stand alone, you can get this from http://www.apple.com/quicktime/download/standalone.html. Reboot PC
4. Dowloaded Itunes from the itunes support site.
Then when you are asked to update say no. Reboot PC
This should then work.

When trying to open a PDF format using Adobe XI I get an error message that there's a problem opening the document (57)

When trying to open a PDF format using Adobe XI I get an error message that there's a problem opening the document (57)

Hi chasore,
Are you still facing this issue?
Is this issue happening with all the documents you have. If yes, i would suggest try uninstall and reinstall. Or if the documents are located on some shared drive try to copy them on local machine and test again.
Regards,
Ajlan Huda.

IDOC_INPUT_ORDERS with error message RV45A-VBAP_SELKZ (2) is not input fiel

Hi
I am creating a multiple line sales order from Idoc and using the FM IDOC_INPUT_ORDERS. The idoc is processed with status 51 with error message RV45A-VBAP_SELKZ (2) is not input field.
It only happens for Idocs that are processed 1st time (re-processing is succesfull) and only in the background (if processed first time in foreground - it is ok).
Have you ever seen this message?
Thanks,
Magda

Hi Joy
Thanks for an idea of creating a BDC from bdcdata before calling VA01 from an IDoc. I could analyze it and to correct an error I added some code in the user exit ZXVEDU04. I simply replaced all concurrencies of RV45A-VBAP_SELKZ (2) with RV45A-VBAP_SELKZ (1) and it worked:
* MW Replace RV45A-VBAP_SELKZ(2) with RV45A-VBAP_SELKZ(1)
move dxvbak to i_dxvbak.
if i_dxvbak-bsark = 'WINT' and dxbdcdata-fval eq 'SICH'.
dxbdcdata-fnam = 'RV45A-VBAP_SELKZ(1)'.
modify dxbdcdata transporting fnam
where fnam = 'RV45A-VBAP_SELKZ(2)'.
exit.
endif.
This is called only once when dxbdcdata-fval = 'SICH'.
Hope it helps.
Magda

How to keep the field open for input with error message in report program

Hi,
Need a help in solving the below issue.
"How to keep the field open for input with error message in report program"
Regards,
C.Shasiraj.

Hi...
you have to use the event:
AT SELECTION-SCREEN ON <FIELD> EVENT.
u have to give an error message in this event.
Consider the following Example:
PARAMETERS : NUMBER TYPE I.
AT SELECTION-SCREEN ON NUMBER.
IF NUMBER = 10.
MESSAGE 'Number vakue is 10' TYPE 'E'.
ENDIF.
START-OF-SELECTION.
WRITE NUMBER.

in this if u give the value of number = 10, it will not proceed further, if u give some other value other than 10 you will proceed further...
Execute this program once u will understand....
also Consider the following links :
Regarding events:
http://help.sap.com/saphelp_erp2005vp/helpdata/en/79/34a237d9b511d1950e0000e8353423/frameset.htm
http://help.sap.com/saphelp_erp2005vp/helpdata/en/79/34a23ad9b511d1950e0000e8353423/frameset.htm
Regarding messages:
http://help.sap.com/saphelp_erp2005vp/helpdata/en/c5/aa575426ad11d2954d0000e8353423/frameset.htm
http://help.sap.com/saphelp_erp2005vp/helpdata/en/c5/aa575426ad11d2954d0000e8353423/frameset.htm
This is very useful.......
Reward points if useful....
Suresh....

I am using datasocket in seperate vi, with error catching, but network slowdown causes labview to crash without any error message ...

Similar Messages

Maybe you are looking for