I can't open tiff in raw. I have opened the same files in raw in the past.

Hi D Fosse (and everybody else) are you still there? You won't believe, but I am having the oposite problem! I have some tiff, and they have never been converted to PSD, and I can't open them in raw. Actually, they are scans from the lab. However, they have been in raw sometimes in the past, yes, and they are still tiff. Using your precious info I went to:
Photoshop pref>file handling>prefer camera raw for jpeg and supported file, (I know, they are tiff, but just in case): CHECKED
Bridge pref>thumbnails>pref adobe camera raw for tiff files: CHECKED
Camera raw pref>always open jpeg tiff using camera raw: CHECKED
But the magic didn't work.

What version of Photoshop, Camera Raw & Bridge?
From your description I suspect it's CS3 (since in CS4 the prefs are all now in Camera Raw)...
If so, try purging the cache in Bridge and make sure the tiffs have no layers and are RGB files.

Similar Messages

How can I do to acquire and save date in the same time and in the same file when I run continual my VI without interruption.

I've attached a VI that I am using to acquire amplitude from Spectrum analyzerse. I tried to connect amplitude ouput to the VI Write Characters To File.vi and Write to Spreadsheet File.vi. Unfortunately when I run continual this VI without interruption, labview ask me many time to enter a new file name to save a new value.
So, How can I do to aquire and save date in the same time and in the same file when I run continual my VI for example during 10 min.
Thank you in advance.
Regards,
Attachments:
HP8563E_Query_Amplitude.vi ‏37 KB

Hi,
Your VI does work perfectly. Unfortunately this not what I want to do. I've made error in my last comment. I am so sorry for this.
So I explain to you again what I want to do exactly. I want to acquire amplitude along road by my vehicle. I want to use wheel signal coming from vehicle to measure distance along road. Then I acquire 1 amplitude each 60 inches from spectrum analyzer.
I acquire from PC parallel port a coded wheel signal coming from vehicle (each period of the signal corresponds to 12 Inches). Figure attached shows the numeric signal coming from vehicle, and the corresponding values “120” and “88” that I can read from In Port vi.
So I want to acquire 1 time amplitude from spectrum analyser each 5
period of the signal that I am acquiring from parallel port.
So fist I have to find how can I count the number of period from reading the values “120” and “88” that I am acquiring from In Port (I don’t know the way to count a number of period from reading values “120” and “88”).
Here is a new algorithm.
1) i=0 (counter: number of period)
2) I read value from In Port
3) If I acquire a period
i= i+1 (another period)
4) If i is multiple of 5 (If I read 5 period)
acquire 1 time amplitude and write to the same
file this amplitude and the corresponding distance
Distance = 12*i). Remember each period of signal
Corresponds to 12 Inches).i has to take these
values: 5,10,15,20,25,35,40,45,50,55,60............
5) Back to 2 if not stop.
Thank you very much for helping me.
Regards,
Attachments:
Acquire_Amplitude_00.vi ‏59 KB
Figure_Algorithm.doc ‏26 KB

I just purchased the new Canon SX60 camera. Despite downloading and installing the latest version of Adobe DNG converter, I receive an error message saying that Photoshop CS4 can't open up/convert raw files (.CR2). This is the same file format as used by

I just purchased the new Canon SX60 camera. Despite downloading and installing the latest version of Adobe DNG converter, I receive an error message saying that Photoshop CS4 can't open up/convert raw files (.CR2). This is the same file format as used by the SX50, with which I never had any problem. Does anyone have a suggestion on how to fix this problem? Thanks.

Camera Raw plug-in | Supported cameras I do not see that SX60 as supported. Just how new is the SX60 when was it announces. Its support is not even listed in ACR 8.7 RC

Hi, how can I keep the same zoom level for all the pages I view in Safari and even when I close and open it. Indeed with a 27 inch Imac I have a lot of space, most of the websites are built for smaller resolutions and my sight is dropping !   Thx

Hi, how can I keep the same zoom level for all the pages I view in Safari and even when I close and open it. Indeed with a 27 inch Imac I have a lot of space, most of the websites are built for smaller resolutions and my sight is dropping !   Thx

Hi, how can I keep the same zoom level for all the pages I view in Safari and even when I close and open it. Indeed with a 27 inch Imac I have a lot of space, most of the websites are built for smaller resolutions and my sight is dropping !   Thx

I'm considering buying CC LR/PS package. My camera is Sony a7 - raw ARW. I've been editing using PSE10 and ver 8.7 of the external Adobe DNG converter. Will I be able to open the DNG files in LR with the edits preserved? Will I be able to open the PSD fil

I'm considering buying CC LR/PS package. My camera is Sony a7 - raw ARW. I've been editing using PSE10 and ver 8.7 of the external Adobe DNG converter. Will I be able to open the DNG files in LR with the edits preserved? Will I be able to open the PSD files in LR with the edits preserved? Any import/catalog etc issues between PSE10 and LR?

Lightroom has no problem reading DNG files. Whether the edits you have done to the DNGs you have originally edited in Photoshop Elements 10 I'm not sure. ACR edits made to DNGs are saved in the DNG file itself, as apposed to a XMP sidecar file, so LR should see those edits. At the worst you will get an exclamation mark in the upper right hand corner of the imported DNGs and clicking on that exclamation mark you will get a dialog box asking you to either import settings from disk or overwrite settings. you would select import settings from disk.

When I try to open a pages document on my mac book pro it says "The file 'thesis.pages' couldn't be opened." But i can open the same file on my iPad and iPhone without a problem.

When I try to open a pages document on my mac book pro it says "The file 'thesis.pages' couldn't be opened." But i can open the same file on my iPad and iPhone without a problem.

Thanks very much for the instructions. I encountered this problem this morning myself and the recommendation fixed the problem immediately. When things like this happen with iCloud and Pages it makes me wonder if I might be better off using something else, having just recently had to fix the problem that the current Pages can't read documents I created with a much earlier version until they were "upgraded" by an interim version.

I want an app to close or browse through open apps at the same time by double tapping the home button i can find the open apps with the minus sign on it and dont move

I want an app to close or browse through open apps at the same time by double tapping the home button i can find the open apps with the minus sign on it and dont move

Try a reset: Press the Sleep/Wake button and the Home button at the same time for ten seconds until the Apple logo appears. Note: No data will be lost

How can I make Adobe Acrobat Pro give a warning to another person who is trying to open the same file I currently have open?

How can I make Adobe Acrobat Pro give a warning to another person who is trying to open the same file I currently have open?

You can't.

I have transferd music from my ipod to my new computer and some of the files are not coming over, i have noticed the m4a files come across but the mp3 do not, any ideas how i can resolve this? thanks

I have just bought a new computer and i am transfering my music from my ipod onto my new computer, I have put the files from the music option from my ipod onto my computer. alot of the songs have come across, however there is alot of songs that havent. I have noticed that the m4a files come across but the mp3 does not. the new computer has windows 8 on it, which is very new to me. when i try and play the mp3 files, it will open them up in a different programme and will not open in itunes. does anyone know what i can do?!?!!?!?!
THANKS

Have you looked at the previous discussions listed on the right side of this page under the heading "More Like This"?
BTW this is the iPod touch forum

I'm using acrobat pro in my project after debuging the project and after opening a certain number of PDF files I receive the message: the maximum number of files opened has been reached, you have to close some files to continu.even doing that, I steel rec

I'm using acrobat pro in my project after debuging the project and after opening a certain number of PDF files I receive the message: the maximum number of files opened has been reached, you have to close some files to continu.even doing that, I steel receive the same message.Some one can tel what to do please? Thanks

Hi Memalyn
Essentially, the bare issue is that you have a 500GB hard drive with only 10GB free. That is not sufficient to run the system properly. The two options you have are to move/remove files to another location, or to install a larger hard drive (eg 2TB). Drive space has nothing to do with SMC firmware, and usually large media files are to blame.
My first recommendation is this: download and run the free OmniDiskSweeper. This will identify the exact size of all your folders - you can drill down into the subfolders and figure out where your largest culprits are. For example, you might find that your Pictures folder contains both an iPhoto Library and copies that you've brought in from a camera but are outside the iPhoto Library structure. Or perhaps you have a lot of purchased video content in iTunes.
If you find files that you KNOW you do not need, you can delete them. Don't delete them just because you have a backup, since if the backup fails, you will lose all your copies.
Don't worry about "cleaners" for now - they don't save much space and can actually cause problems. Deal with the large file situation first and see how you get on.
Let us know what you find out, and if you manage to get your space back.
Matt

How do I stop more than one user opening the same file?

I'm about to install Lion Server and we're concerned that more than one person will be able to open the same file at the same time. Can this be prevented? If not it seems to make the concept of a server pointless?
Any help appreciated. Already annoyed I have to phone and order 10.7 Server as it's no longer on the App Store. Can't run 10.8 as the Mac Pro is too old and Apple have cut us off.

The file server software supports file locking, but multiple file access is application-dependent. In some cases it's entirely valid for multiple users to access the same file. It's up to the application to allow or deny this.
Ordinarily, if an application requires exclusive access it should flag the file accordingly when it opens the file. This will prevent other users from opening the file. However, it's not up to the server to do this.

I can't send emails from Mail. I have three different accounts set up and have the same problem with all. The mail just sits in my outbox. All worked fine until Yosemite upgrade. Recent update has not fixed problem.

I can't send emails from Mail. I have three different accounts set up and have the same problem with all. The mail just sits in my outbox. All worked fine until Yosemite upgrade. Recent update has not fixed problem.

I have been experiencing the same problem. My mail app won't even open on my Late 2011 Macbook Pro. It will show as open, but the app will never actually show up.

How can I save images and text data to the same file?

I have been looking at ways to do this for a while. My main VI saves the raw data to a text file which the users then import to Excel and plot. I am trying to simplify this process and have been looking at ways to accomplish this task. I want to be able to save the raw data to a file and then save the Labview graph as well. This will eliminate the tedious task of importing the raw data into Excel and plotting it. I can save the raw data to its own file and I can use the Get Image method for the graph and save it to its own file. I am currently using the .png format. Is there a way of saving both to the same file ie, importing the image into Excel or Word etc. Before I go off doing a science project I wanted to see if anyone else had experience completing this task and had any recommendations. Thanks in advance for any help.

well ther are a couple of ways. You could use the standard report generation VI's and make a complete report with the image of the graph embedded into the report with the raw data or you could use activeX and control excel thru LV and put the raw data into excel directly and have excel graph the data without any user interaction. I have posted a slew of VI's on the excel board if you do not have the report generation toolkit. If you could tell me which way you want to go I could possibly send you an example.
For more information and some sample VI's and tool kits, you can go to the excel board
Joe.
"NOTHING IS EVER EASY"

Two users opened the same file at the same time with file on Win2K Server

I just had a problem with a file that could not be saved. After a little investigation I discovered that two users had the same file open at the same time. This is with both users using InDesign CS2 and saving to a Windows 2000 Server. Any ideas how this even happened? The only thing I can think of is if they both opened the file at the exact same time but even that I doubt. I guess the more likely possibility is that the user on 10.5 (which we have had a lot of problems with, it's hard to tell how many of them are CS3 problems (yes CS3) and how many are Windows 2003 Server problems) had InDesign CS2 flake out and not tell her the file was open. Has anybody else seen this? The other user was using 10.4. Both computers have the most recent updates for the OS and for their various adobe products.

I have videos on mov file and my quick time player does not play them.
The MOV file container is the generic QT file container. Any audio and video data compatible with the computer system used to create the file can be placed in the MOV file container. Unfortunate, other systems cannot play the file unless they too are configured with the same components as those used to create the file. The normal procedure here is to use the Finder "Info" or alternative media play "Inspector" window to determine what codecs were used to create the original file and, if they are available for your Mac, install them on your system for playback use. Also be advised that some "legacy" codecs may require playback in the QT 7 Player for proper QT support.
I opened with other players, there is no sound. Then I opened the same file on my windows 7, it plays perfectly with the sound and everything? What is the problem?
This would indicate these players either access your QT codec component configuration which does not include the required codec or the app has its own built-in codec support which does not include the required audio codec but you Windows 7 media player is configured with the required codec support. This may incidate the use of a really old codecs that may or may not be available/supported on a Mac any longer.

How do I open make iBooks regognize two books created in iBA as different books/files? (iBooks opening separate books as the same file)

I am trying to load two different books created in iBooks Author into iBooks. These books were exported instead of uploaded to the iBookstore, therefore I download them and then open with iBooks on an iPad.
Here is my problem:
When I download a book (Book A), it opens in iBooks correctly. If I download a second book (Book B), instead of opening Book B, iBooks re-opens Book A. This also happens vice-versa if I delete Book A and then upload Book B. Essentially, both books cannot be loaded in iBooks at the same time, and iBooks treats the second download/open attempt as the second book being opened, when in actuality it opens the wrong book.
When I looked at the authoring files, I saw they had the same title listed in the Book Pane in iBA. Even when this title is changed, the books fail to open correctly in iBooks.
Has anyone run into a similar problem? Also, I am wondering if legacy meta data is a possible reason for iBooks to open the same book twice instead of loading and opening the new book? (if this is the case, is there a way that this legacy meta data can be deleted)?
Thanks in advance for your help/support.

Update: Solved.
Either creating a new file or saving the old as a template file & renaming it solved my problem.
Here is the discussion where I found that information:
https://discussions.apple.com/message/20351734#20351734

I can't open tiff in raw. I have opened the same files in raw in the past.

Similar Messages

Maybe you are looking for