I can't print to my networked Canon MF8350 from my imac after Mavericks.

Hello eveyone-
I have an iMac, just upgraded to Mavericks, as well as an iBook. They are both connected to my Canon mf8350 via airport- timecapsule- ethernet. The iMac however connects to the timecapsule over an AE bridge.
Printing worked perfectly before the Mavericks upgrade.
The iBook printed just fine right out of the gate, it uses the old Canon 10.1.0 driver, and I have not touched this.
The iMac spooled its print job, then replied "communication error". I repaired permissions, restarted everything, and same result.
I removed the Canon from my printer list and tried to add it, it was not found.
Updated to Canon driver 10.2.0, printer is still not appearing in the list. Reset the printing system, still no dice. Both Canon MF background items are running according to Activity Monitor.
iBook still prints just fine.
Any ideas?
Thanks
Matt

Matthew Poor wrote:
The iMac spooled its print job, then replied "communication error". I repaired permissions, restarted everything, and same result.
Did you add the printer using Bonjour or did you select one of the IP protocols? If the latter, then you cannot use IPP. The Canon MF driver supports LPD or HP Jetdirect.
Matthew Poor wrote:
Updated to Canon driver 10.2.0, printer is still not appearing in the list.
If you mean that after you change the USE menu to "Select printer software" and the Printer Software window is empty, then try restarting your Mac. This can rebuild the printer list.
Matthew Poor wrote:
Both Canon MF background items are running according to Activity Monitor.
The new MF v10.x driver does not install or use the MF Background process. So this process is a leftover from a previous driver. I would therefore recommend you trash the older driver files and run the v10.2.0 driver installer again.
Depending on the version of driver you had installed prior to upgrading to Mavericks, the name of the folder can be different but will reside in /Library/Printers/Canon. Here you will see BJPrinter and IJScanner. Leave them alone and just remove the one or two that have MF in the name.
You then need to navigate to /Library/Launch Agents/ and trash any Canon plist file. Then restart the Mac and run the Canon MF v10.2 installer again and then see if you can add the MF8350.

Similar Messages

  • Can't print to ethernet networked printer... suddenly!

    Today, for some reason I can't print to our networked printer, a Kyocera FS-6950DN laser. All I am getting now is a 'Network host is busy, will retry in 10/15 secs' and the job just holds.
    So, what have I tried. To eleminate any printer issues I have successful managed to print direct from my MacBook (also running OSX 10.6.8) without a problem. So the printer seems fine. However, if a connect directly (again via a single ethernet cable) to my MacPro it won't print. I have deleted the printer and created a new one. Actually, I have done this several times. When I go to create a new printer I can see the printer listed a a bonjour printer. I select it, then I use 'generic postcript'.  I can choose the my printer here, but I seem to remember that this was a problem when I set it up originally and I was advised to use the generic option. I click add and that used to work. But not now. I have checked that the printer has a static ip address and it does. I have also tried adding the printer as an IP printer and adding the IP address etc maually, but again this doesn't work. I've tried this both with LPD set or IPP set. I get the same busy error message.
    Trawling the net I have noticed lots of people with Kyocera print issues relating to the latest OSX Snow Leopard 10.6.8 update. Although having succesfully printed from my MacBook that would suggest that 10.6.8 isn't the issue in my case.
    Any help or pointers in the right diection would be greatly appreciated.
    Many thanks – Roy
    I should also say that I have done the usual... repaired the permissions and reset the PRAM etc. I have ping tested the connection from my MacPro and there is a response from the printer. It's just not finding the printer when I send the job to print?

    Managed to fix this by changing the ip address on the printer. It seems that the address was out of range for our new router. Changed the printers static address back to something within range and the printer bust into life. Simple as that. Only took me a day and a half to work it out... : )
    If you have similar issues I hope that my post is helpful.
    Roy

  • Can I print in just black and white from my iPad to an hp5510 photosmart printer?

    Can I print in just black and white from my iPad to an hp5510 photos mart printer? 
    It seems ePrint is no longer available and now forced to use HP Connect. I am not seeing the option to print in black and white. Printing email messages in color is a waste of ink. Any help would be appreciated.
    Thanks

    I was using ePrint however that is auto-directing me to HPConnected and I no longer have the option to change the printing options to Black and White or Color. This is a recent change for me.
    banhien wrote:
    Hi,
    Yes, you have to use HP Connected now. Do you use AirPrint or ePrint ? ePrint allows you to select Color or Grayscale under Color mode (note: Grayscale ALSO uses color inks).
    Regards.

  • I can only print 1 copy at a time from indesign booklet on my xerox d95

    I can only print 1 copy at a time from indesign booklet on my xerox d95>

    I've never used Print Booklet or your printer, but some things are determined by the printer and printer software, rather than the program from which you are printing. You might want to see if Xerox's website has any info also.

  • Can't print web pages or e-mail from Firefox after update

    Since the last update, to 7.0.1, I can't print web pages or e-mail from my Yahoo! account. The computer says it can't communicate with the printer. I can print from Internet Explorer, Word, and Adobe Acrobat so I don't know why the computer is not communicating with the printer using Firefox. I am still running Windows XP--does this version of Firefox requires a newer version of Windows?

    Try the '''''reset''''' described here: <br />
    http://kb.mozillazine.org/Problems_printing_web_pages#Reset_printer

  • HT204003 how can i print a boarding pass image file from passbook?

    how can i print a boarding pass image file from passbook?

    I do not believe that Passbook supports printing. You can email, but not print. Then again I'm not sure what it actually emails, if that is a graphic of the card or what. I'm going to try it with my Starbuck's card, but there is no setting for printing within Passbook.
    EDIT: Actually it sends the email as an attachment for a Passbook card file, that cannot be handled by my computer. Hope that answers your question.
    Message was edited by: ChrisJ4203

  • Creating a Mavericks USB boot drive after the horse has bolted.  Can I create a bootable USB drive from my iMac after installing Mavericks without saving the Install OS X Mavericks.app file?  Do I need to re- download the whole 5.29 Gb again?

    Creating a Mavericks USB boot drive after the horse has bolted.  Can I create a bootable USB drive from my iMac after installing Mavericks without saving the Install OS X Mavericks.app file?  Do I need to re- download the whole 5.29 Gb from the App Store again?  My problem is my 4Gb/month allowance on a 12 month contract.  I cannot purchase a data block from my ISP and although my speed is theoretically slowed to 64k after reaching my 4Gb, it actually ceases to download in reality.

    HI tasclix, it depends what you mean by an OS X boot drive.
    If you want a recovery disk from which you can reinstall (by re-downloading) or recover from a time machine backup, then nbar is correct.
    If, however, you want to boot and run the OS X installer from the USB drive (so that you don't need to download again), then you will need a copy of "Install OS X  Mavericks.app"; see this article:
    http://support.apple.com/kb/HT5856
    Before downloading again, search your system to see if the installer is still there - it's usually in the /Applications folder unless it has been deleted, but check your whole system for it anyway, you never know, you might still have it somewhere.
    Message was edited by: SilverSkyRat

  • How can I access my icloud iphone back up from my imac?

    how can I access my icloud iphone back up from my imac?

    I'm afraid you can't without using third-party software such as Wondershare Dr.Phone. 

  • Hi, can iMovie give pronlems during the boot process from my iMac Mine. I have often after working with iMovie that i get during the boot Psi SDXH pause so the boot process stops

    hi,
    can iMovie give problems during the boot process from my iMac Mini?
    I have often, after working with iMovie that i get during the boot Psi SDXH pause
    so the boot process stops at this point
    I have often reinstall OSX Mavericks
    regards,
    HenkfromWinterswijk
    Netherlands

    Hello Federico,
    Your EliteBook is a Business model.  Your issue would be best answered on the HP Enterprise Business Community Forum
    Good luck!
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • It is difficult, to organize my contacts on my iPhone. It is easy to do this on my iMac. So why can't I load my well organized contacts from my iMac (addressbock) on my iPhone and overweight my disorganized contacts on my iPhone?

    It is difficult, to organize my contacts on my iPhone.
    It is easy to do this on my iMac addressbok.
    So why can't I load my well organized contacts from my iMac (addressbock) on my iPhone and overwrihte my disorganized contacts on my iPhone?

    Read the User's Guide, it will reduce the number of questions you ask which reveal to the world your intelligence or lack there of.

  • Printing with a networked Canon iR 3220 and my Intel iMac

    I am at my wits end and I hope someone can help.
    I am the sole Mac user in my company. I have a brand new, shiny 24" dual processor (intel) iMac running OS 10.4.9, that is connecting wirelessly to our network. We have a mixture of IIS and Linux servers (I believe the IIS is solely for the Windows Exchange server) Ther are 30 or so printers on the network and the one I am supposed to be printing to is a Canon Image Runner 3220 (iR 3220).
    I am no Mac newbie, but I can't get the thing to print correctly. I have updated the driver from Canon (v. 1.70PS) and the PPDs (v. 2.25), followed the instructions and it will not automatically select the correct PPD. When I reset the PPD manually, it spools to the printer, but then stops all my print jobs. I try to resume and it spools and stops.
    I have tried adding the printer via CanonIP, LPR, Appletalk (which gets me a message that I am connected incorrectly), setting up a sacrificial altar to the printing gods...nothing seems to work. I've tried using the iR 3200 driver and that doesn't work either.
    Does anyone have any suggestions? I would appreciate any help I can get at this point.
    Mike

    Hello Mike,
    The first thing you need to do is determine if the iR C3220 is using the Canon printer board or the imagePASS-C1/C2 print server option. If you look at the back of the iR C3220, and there is a rectangular box with an Ethernet cable connecting to the copier, and what looks something like a SCSI-2 cable also connected between the white box and the copiers interface board, then you have the imagePASS controller. This device requires a different driver to the PS v1.70 and PPD v2.x you are currently using. It also requires a queue name of 'print' or 'direct' (or 'hold' if you don't want the job to print) and it must be entered in lower case.
    Since it sounds like there are PC's on the network, have a look at their printer setup and see which driver they are using. You can also check their port config to see how they are connecting.
    If the iR C3220 doesn't have the imagePASS print controller and the PC users have the PCL5c driver installed, then you may find that the iR C3220 doesn't have the PS option - it may be PCL5c only. The easiest way to tell is to open the printers web page (called RUI) by entering the printers IP address in your browser of choice. With the default page open, select Additional Functions and then Custom Settings (you may be prompted for a system ID & password). If you get past this the new view will show if you have PS as well as PCL. If there is no PS, then you will have to look at installing the latest version of Gutenprint and selecting Generic PCL5c as your 'ppd'.
    If the PS option is installed, then the v1.70 driver should be okay, although there is a trick to adding it. In the Printer Setup Utility, after clicking Add, select More Printers and then Canon IP (PS). In the new window input the IP address and a queue name of LP. When you click Add the copier is queried by the driver to determine what model it is, meaning that once it is displayed in the printer list it should show the iR C3220. Given that this didn't happen for you (and if the imagePASS is not being used) then a likely cause can be the disabling of SNMP in the copier setup. You may have to get the IT guys to enable this (or at least explain why it is off).
    If you go the other way of manually selecting LPD as the protocol (AppleTalk is not supported by the PS v1.70 driver) then you need to ensure that for the print using you select iR C3220 CanonPS for the ppd. If you see Canon iR C3220, don't use this as it is the wrong ppd for the PS driver - it is there as part of the PPD installer.
    If you want to try using the PPD, then you can use AppleTalk but of course this has to be enabled in the copier, and if your the only Mac then it is likely that it is disabled. Again the RUI page can tell you this or you can print a Config page from the copier (I think you go Additional Functions > Report Settings > Network > User Data List).
    Hope something above is helpful and if not, please reply back.
    Paul

  • Can't Print to Canon ImagePROGRAF 600 with IMAC running Mavericks

    I have a new IMAC running Mavericks connected to a networked Canon Plotter. I can plot to it using my old MacBook Pro running snow leopard with the 2009 Driver Ver. 2.17. And my office mate can print to it using a 2009 IMAC running mavericks with the 2012 Driver and ver. 3.10. When I go to print, in the page set-up of the print window I can only select MANUAL for the paper feed, I can't change to cassette or Roll, and then an alert pops up saying: "Manual is not available..."
    If I ignore that and continue trying to print I get a printer error message say: "Open error: Try turning the printer off and back on again..."  This doesn't work either.
    I've tried going backwards in software generations but that only creates more problems. The Mountain lion version allowed me select MAUAL or CASSETTE in the page set up window but then the ImagePROGRAF Preview said "That function is not support by this printer." Has any one experienced this and solved it?  Thanks.

    lambarena wrote:
    When I go to print, in the page set-up of the print window I can only select MANUAL for the paper feed, I can't change to cassette or Roll, and then an alert pops up saying: "Manual is not available..."
    I think this could be related to a communication problem between the Mac and iPF. I don't have an iPF600 but do have an iPF8400 and iPF9400S. I downloaded the v3.10 driver for 10.8 and installed it on 10.9.5. I then created a dummy IP address and selected the iPF600 driver. When I first tried to print I got the following pop-up.
    As this IP address was not connected to any printer I cancelled this window and then found the same symptom as you i.e. Only having Manual and selecting it resulted in an error window appearing. I also found that when I changed to the Main menu, the Media Type drop menu was stuck at Plain Paper.
    I then created another printer to the iPF8400 but using the iPF600 driver. When I selected to print, I got the pop-up again. This time I entered my password and then found that the drop menus worked in Page Setup and Main.
    So when you added the iPF600 to Printers & Scanners, did you get the pop-up above?
    Also, if you select the Main menu, is the Get Information button available?

  • Can't print with adhoc network for HP 7780 all-in-one

    Operating system is Windows Vista 32 bit.
    Downloaded full driver software from HP site and installed it OK with wired connection to printer.  All works fine in this mode.
    Now I want to do wireless printing via an adhoc network called MYNetwork that I generated on my computer with WEP security.  The printer detected the network, I put in the 5-digit password on the printer control panel, and the network was then connected.  It shows connected on my computer also.
    So  now I am connected to the adhoc network, what are the next steps to make the printer show "online" and to actually print wirelessly?  I really feel dumb asking this, as  the answer must be simple.  PLEASE Help!!
    Note that I have completely disconnected the wired connection from the printer to the computer.
    Thanks,
    Garry

    1. Make sure the printer is turned on and connected to your network. Verify that you can access the printer's internal web page by browsing to its IP address before continuing.
    2. Click >> Start >> Control panel >> Printers.
    3. Click the Add a printer
    4. Select Local printer
    5. Select Create a new port and select Standard TCP/IP Port and click Next button.
    6. Under Device type, select TCP/IP Device. Under Hostname or IP address, enter the printer's IP address. Click Next.
    7. Select Hewlett-Packard from the list of manufacturers and select and select your printer model. Click Next.
    If your printer model was not listed, then select Have Disk, browse the HP CD that came with your printer and select the first file that starts with hp and ends with inf. Click Open then OK. Select your printer model. Click Next.
    8. If you are asked, use the currently installed driver.
    9. It will ask for the Printer name -- enter a new name or use the existing one. This will be the name of the printer that you select from other applications.
    10. You may be asked to share the printer. Choose NO.
    11. The Print Test Page box appears. Go ahead and print it.
    12. Click Finish.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Can't Print Adobe files on Canon ir c4080

    Ok, so we just upgraded our printer from a Canon ir C3200 to a ir C4080. When using any Adobe programs (basic image 11x17 with lines going to the edge) we can not print on 11x17 paper with "auto tray select" on and a basic change in 'printer setup'. We have to go all the way into the printer options and force the tray selection in order to get Tabloid.
    I've had our leasing tech here and we thought we had it fixed, until we opened a new file and then right back to the same old Tabloid sized print on Letter sized paper.
    I can provide some screen shots if necessary, but I'm just wondering if anyone else has run into similar problems?
    Tests:
    Illustrator (where the initial problem was discovered)
    Acrobat (as a test found the same issues of not printing to the desired paper size)
    Safari (prints to correct paper size NOT A PROBLEM)
    couple of PCs (prints to correct paper size NOT A PROBLEM)
    Any thoughts?

    Custom Presets are one solution... Maybe I should have phrased my question differently. On the initial "Print" menue that comes up there is a window RIGHT IN THE MIDDLE that is for the "MEDIA" and you have the ability to change those settings, however apparently this is a strictly cosmetic setting because the printer still prints to the default tray. What is the point of an "Auto Tray Select" option if the printer AUTOMATICALLY selects the default tray and completely ignores the user's input as to what paper size he/she wants?
    I guess I'm more wondering if Canon just has a bad software interface or if OS X just doesn't play well with it?
    Thanks for your input(s)
    Jason

  • Can't print over Airport network while in Windows XP SP2

    My printer works fine over my airport network while in OS X, but I can't print when booted in windows XP SP2. I CAN get on the internet over the Airport network while in XP. Can any body help?

    Install Bonjour for Windows this fixed my ablity to print via an Airport Base station from Windows.
    Search Apple Downloads for Bonjour download for Windows.

Maybe you are looking for

  • Safari 5.0.5 freezes on wake

    If I close my MBP, with Safari open, it freezes when I open it back up.  All other programs work, but slower. Took it to the Genius (sic) bar and they told me to install Clicktoflash to block flash.  Still froze. I've reset Safari and deleted the pre

  • Can't install trial Adobe Flash Professional.... arrrrrrrrrrrrrrrrrrrrrrrrrrrrrgh

    Yes I've done a search, and although posted many times, solutions are few and I've given them all my best shot.... Installing ADBEFLPRCS4Win_LS1.exe reaches about 19%, then jumps to 93%, makes 100% then states: A problem occurred while extracting som

  • Pre-Populate AD Groups upon Provisioning of AD User

    I've been trying to figure out how to auto-populate groups in AD for users based on a single attribute in the OIM User Profile. For example, if a user's geographic code on the OIM User Profile is TX and he has an Administrator title, then I want that

  • Document Type - Object link to be made mandatory

    hi All, We are having a requirement that - For a particular 'Document Type' Object link shall be made mandatory. Ex: For Doc. Type: ABC - 'Sales Document - Item' is MANDATORY       For Doc. Type: XYZ - 'WBS Element' as Object link is MANDATORY How do

  • Oracle Form - use in batch mode

    How could I launch a procedure triggered by a form in batch mode, without the need of interactive operations. I should be able to pass all the parameters that can be set in interactive mode Is there any standard way to do that? Nicola