I cannot get my Airport Express to accept wireless clients.

I cannot get my Airport Express to accept wireless clients. After resetting to factory default and reconfiguring, it works briefly but then stops again.
The Airport Express is on the second floor of my house and is seen by Airport Utility. Using a LAN cable with the Express works no problem.
My network is created by an Airport Extreme (ground floor) and extended by a Time Capsule (first floor)
The issue is most likely due to the fact that the AirPort Express may be too far from the AirPort Extreme to properly extend it with enough bandwidth to be useful.
It is important to understand that with Apple 802.11n or 802.11ac base station an extended network works in a wheel-like fashion with the base station to be extended at the hub and each extending base station along one of the spokes. This type of configuration does not allow for daisy chaining the base stations. That is, in your case, both the Time Capsule and AirPort Express are attempting to extend the AirPort Extreme.
Each extending base station must be within a certain signal quality range in order to extend the network properly. Please check out the following AirPort User tip for details.

Similar Messages

I lost my internet last night and now i cannot get my airport express to work

i lost my internet last night and now i cannot get my airport express to work it is blanking yellow on /off

Have you tried AirPort Utility it the Utility folder? If so, what was the result?

Cannot get my airport express to allow multiple internet users.

Good morning. I recently had TW install internet and phone (cable, but no TV) at my home. My modem is a Scientific Altanta DPC 2203 and I have my AirPort Express hard-wired to the modem. I was able to access internet using my MacBook, but cannot get a wireless connection on my iPhone, my beau's iPhone or his laptop. Time Warner (RoadRunner) keeps insisting the problem has to be in the wireless router. I have read the manual for AirPort Express and run through every tab of the set-up menu and cannot figure out what is wrong.
I would be grateful for any help you might offer. I'm convinced this is a simple problem and I'm overlooking something obvious, but maybe not. The tech support people at TW are very argumentative and insistent that this modem does not distinguish or create single users. In my experience, it is usually an issue with the router, not the modem.
Many thanks,
Elaine

On your Mac.....
Open Macintosh HD > Applications > Utiltiies > AirPort Utility
Click Manual Setup
Click the Internet icon
Click the Internet Connection tab just below the icon
Settings should look like this.....
Connect Using = Ethernet
Connection Sharing = Share a public IP address
Click Update to save any changes and allow 40-45 seconds for the Express to restart
Power down everything on the network....modem, Express computer(s), printers, etc.....order is not important
Wait at least 15 minutes...longer will not hurt
Start the modem first and let it run for 2-3 minutes by itself
Start the Express the same way
Start each device one at a time about a minute apart until everything is powered back up
Check for proper operation.
Call the cable company to tell them they were right

Cannot get my airport express to work

The amber light keeps blinking and cannot get it to sync to the WiFi system at home. Was working fine at our last home but just cannot get it to sync. Any suggestions?

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.

I can't get my Airport express to work in client mode with my speedtouch base station?

Im trying to add my Airport Express to my exisiting wireless network - which runs from a speedtouch base station. I only want to use the AP to use air tunes but i cant seem to get it running in client mode. The interface on the Airport Utility seems different to that described in the online help here: http://support.apple.com/kb/HT1731
Everytimes i try to add it to an exisint network the AP dissapears on its restart. Any ideas if what im trying to do is possible. I've tried creating the network initially with the ethenet cable connected - which works, but then when its detatched although the AP status light stays green it disapears from from the network and i cant stream.
thanks for any help and advice.
Wilkie

In order for the AirPort Express to join another wireless network as a "client", three conditions must be met in the setup of the Express. It must be provided with......
1) The name of the wireless network that is to be joined
2) The exact type of wireless security settings that the wireless router is using
3) The wireless network password
Most users have no trouble with 1) and 3), but few know the exact type of wireless security settings that their wireless network is using. So, they accept a default setting on the Express, which does not match up with their network.
Bottom line....unless you know the exact type of wireless security settings that your wireless router is using...the Express will never join the network. The setup ends with an error message and you have to start all over again with another try....which will fail as well, etc.
If you know the exact type of security settings that the Speedtouch router is using.....we can provide you with a step by step setup guide.
If you do not know this, or are unsure....you will need to get into the setup menus for the Speedtouch router to locate the wireless settings. Or, if the wireless router was provided by your ISP, they may be able you with this information.
Post back with that info and we will proceed.

How can I get the Airport Express to handle all the PPPoE stuff?

Hi, I’m visiting my family in China, and now trying to help my dad, with his Airport Express and how to set up a PPPoE connection.
We have currently set up the Airport Express in bridge mode (not distributing IP adresses and selecting DHCP under the Internet tab in admin utility). The Airport settings on our two computers is set up to connect using PPPoE using the given login name and password. (ps! we can not see the Base station in Airport Admin Utility when using these settings, we would have to select a new location from the Apple menu to see it and make condigurations.)
What we want is to do, is to have the Airport Express connect to the ISP using a PPPoE connection and not through the computer.
I know there is a 'Connect using PPPoE' option in Airport admin util, letting me input account name and password. If I select this setting instead of DHCP, enable distribution of IP addresses and configure my Airport card to NOT connect using PPPoE, I will see my base station in the Airport admin util with the IP address of 10.0.1.1 (or similar) and my computer will have x.x.x.2. Next to the Airport icon in the menubar, a scrolling message will say 'Looking for PPPoE host' without anything happen. I am sure my account name and password is correct as they've both worked when using this computer to connect to PPPoE (like now)
How can I get the Airport Express to handle all the PPPoE stuff without using bridge mode?
Ps! Both me and my dad have iPhones whom we can’t seem to get to connect unless its been distributed an IP address cause there's as fars as I know, no options of inputing a PPPoE user name and password.

Any solutions to this? I'm in China also, in Beijing, trying to get my Airport Express to work with an ADSL modem.
Direct ethernet cable connection to my Macbook works fine.
When I configure the Airport Express with the ID and password that seems to be fine also – Airport Express shows a green light.
But I cannot figure out the settings to connect wirelessly from my Macbook to the Airport Express. I get a constantly scolling message: "Looking for PPPoEhost..."
thanks
Paul

I'm trying to activate my Airport Express to a wireless network powered by an Airport Extreme. I get an error message that says I need to Use Airport Utility 5.6. My system is currently running Airport Utility 6.1

'm trying to activate my Airport Express to a wireless network powered by an Airport Extreme. I get an error message that says I need to Use Airport Utility 5.6. My system is currently running Airport Utility 6.1

Is your AirPort Express an older 802.11g model? If so, you will need to install v5.6 if you are running OS X Lion or 5.6.1 if running OS X Leopard or Snow Leopard. Unfortunately, the iOS version of the AirPort Utility cannot administer these older base stations.

Airport Utility cannot find my Airport express on Windows 7

   I have a working Airport express with a static ip address. The static ip address has been hard coded in my main router. The airport express is connected to my network via ethernet cable. Airport Express Version 7.6.1. I am having conectivity issues from my new Windows Desktop. The airport utility 5.6.1 on my new desktop cannot find my airport express. The manual setup button has been greyed out. I can ping the device. I can click on "configure other" and configure the airport-express (which is how I set it up).    If I reboot my desktop and then quickly fire up the airport utility, it finds the device. On hitting rescan, in a few minutes everything gets greyed out again.
The airport utiltity on other computers is able to find that airport express.   I am able to stream music through the airport express from other computers in the network.
How do I find out what is blocking the airport utility on my new desktop. The Bonjour Service is up and running.   Any help/advice on trouble shooting this issue is appreciated.

The airport utiltity on other computers is able to find that airport express.   I am able to stream music through the airport express from other computers in the network.
You only need one computer on the network to access the settings in the AirPort, so unless you like to look for things, it is probably not worth the effort to try to troubleshoot the blocking action on the Windows 7 machine.
It is not always the Windows Firewall and/or the anti-virus program that blocks connection attempts like this, but that would be the first place to look.
In general, you have to get into the Firewall settings to create an "exception" for the AirPort connection. The same would be true for the anti-virus if that is what is blocking the connection attempt between the PC and AirPort.

Network name comes up, but cannot connect to Airport Express

Recently it seems that every other day I cannot connect to my Airport Express. The wireless network name always appears; however, when I try to connect to that network (I have it password protected), I get a "timed out" error. I then have to unplug the Airport Express and plug it back in to reboot. Connecting back to the network always works after that.
Is this an Airport Express issue or my home internet connection issue?

So did i screw something up last night when i connected using my PC?
That sounds likely. Maybe the security type or password?
And if so how do i re-set the link with my mac??
Try the options described on pp. 30-33 of http://manuals.info.apple.com/enUS/AirPort_Express_SetupGuide.pdf
Once you get things working again, suggest you save the settings in a profile. In future when you bring the PC home, create a different profile for experimentation. Switch back to the usual profile when you're done with the PC. Eventually, you should be able to develop one profile that works with both machines.

Itune on iMac cannot connect to Airport Express, but Itune on XP can

Hello
I've the following situation:
Itune cannot see the Airport Express unless my Iphone Remote controle is connected to Itune. And eventhough, Itune fails to connect to it.
Here is the environment of my network
1) third party LAN/Wireless router (connected to the internet)
2) iMac (10.4.11) connected via the LAN port to the router
3) Airport Express (7.3.2) connected to the wireless network
4) one Iphone connected to the wireless network
5) one XP computer connected to the wireless network
6) All devices are in the same subnet
What really puzzle me is that Itune on the XP laptop can broadcast music to the Airport Express without any issue. But Itune on the Mac does not see at all the Airport Express unless I connect my Iphone to Itune. When I do so, the Airport Express become listed in the status bar of Itune. But if I try to make Itune connect to it, it try for a while then it stop trying without any error message.
I really don't understand what is going on. Does any body can give my a bit more information how Itune and Airport Express communicate? Or have any idea where I should direct my troubleshooting?
Thanks in advance for any help

So did i screw something up last night when i connected using my PC?
That sounds likely. Maybe the security type or password?
And if so how do i re-set the link with my mac??
Try the options described on pp. 30-33 of http://manuals.info.apple.com/enUS/AirPort_Express_SetupGuide.pdf
Once you get things working again, suggest you save the settings in a profile. In future when you bring the PC home, create a different profile for experimentation. Switch back to the usual profile when you're done with the PC. Eventually, you should be able to develop one profile that works with both machines.

Cannot see my Airport Express

I have two AirportExpress and one TimeCapsule. I can see all three using a PC AirPort Utility. However, from a MAC AirPort Utility I can see only one at the time (I can see only the one I am connected to wirelessly). All three devices are connected to the same ethernet network with cables. How do I get the MAC to see all three device simultaneously?

I just did. Now I cannot neither the AirPort Express nor the TimeCapsule that I am connected to. However, I can still see all three devices on the PC.

I cannot get my Airport Extreme to talk to my cable modem

I cannot get my Airport Extreme to talk to my cable modem. Cable modem is a Cisco, new, Charter cable company. New wires throughout. Connected to internet currently hardwired to cable modem. So I have internet service to the modem.

The modem needs an extended power down period in order to reset, as it is "remembering" your computer and thus will not associate with the AirPort Extreme.
See this User Tip from forum expert Tesserax:
AirPort - Complete Power Recycle

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Sometimes I cannot select an airport express to output sound from a current model mac air/10.9.3. The output jumps back to internal speakers or apple tv. Any ideas?

Hello Cloud19,
The article linked below provides some helpful information and troubleshooting that can help resolve issues with AirPlay and your Airport Express.
iTunes: Troubleshooting AirPlay and AirPlay Mirroring
http://support.apple.com/kb/TS5209
Cheers,
Allen

HT4628 I recently transferred my internet service to another state. Have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the i

I recently transferred my internet service to another state.I have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the internet. Any suggestions?

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

I cannot get my Airport 5.5.3 to "see" my newtimecapsule, hooked to my Windows XP desktop via an ethernet cable.

I cannot get my Airport 5.5.3 to "see" my new timecapsule, hooked to my Windows XP Desktop via an ethernet cable.

How are you trying to setup the Time Capsule?
Wireless-> Network Mode, should be OFF as you already have wireless through your modem/router.
Network-> Router Mode, should be set to OFF "Bridge Mode".
Internet-> Connect Using, should be set to "DHCP".
Also, does your modem/router have a battery backup inside?
If so, you would need to remove the batteries to reset the network.
Let us know more about what you have and your setup.

I cannot get my Airport Express to accept wireless clients.

Similar Messages

Maybe you are looking for