I could not shut down because and email could not delete

i could not shut down because and email could not delete, I did a hadr shut down, now it won't restart at all

Try resetting your iPhone >  iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting

Similar Messages

  • My computer will not shut down because my email is open but my email is not responding to anything. How do I get it to shut down?

    I have been trying to shut down my macbook pro for the past half an hour but it says I need to quit my email before I can shut down. I can not get my email to respond I have pressed quit about 50 times and it just doesnt do anything! Earlier I tried to clean out my email and it said that not all the mail could be "put into the trash on my mac". This is a new macbook and I am at a total loss because I havent had it very long! Someone please help!

    Force Quit Mail.
    Press command + option + esc keys together at the same time.
    Wait.
    When Force Quit window appears, select Mail if not already.
    Press Force Quit button at the bottom of the window.
    Wait.
    Mail will quit.
    If this does not help, press the power button for 7 or more seconds.
    Computer will shut down.
    Restart.

  • HT1414 Anybody have an ipad that will not power on, for no reason? My ipad always worked fine and then one day it shut down because the battery was low so I plugged it in and it will not power on. Tryed the hard reset option still no power on :(

    Anybody have an ipad that will not power on, for no reason? My ipad always worked fine and then one day it shut down because the battery was low so I plugged it in and it will not power on. Tryed the hard reset option still no power on

    You can try recovery mode to see if you can revive the iPad.
    http://support.apple.com/kb/ht4097
    Have you left the iPad charging for a couple of hours or so to be sure?

  • Macbook Pro shut down because the battery power ran out. Now I cannot start it and the battery will not charge. Only one green battery charge light lights up and blinks.

    My Macbook Pro shut down because the battery power ran out. Now I cannot start it and the battery will not charge. Only one green battery charge light lights up and blinks on the left side. I am running Lion. How do I get this to charge and turn on? Thanks

    If your model Macbook Pro is the calibrating model, let the battery calibrate. 
    If not, and are still under warrant or have Apple Care, give them a call and get a case number.  Otherwise, take the computer to an Apple store or an AASP.  Whichever is more convenient for you. 

  • Oct 22, 2013 11:58 PM downloaded 10.9  all well 'til I get desktop and can't enter my password, message of error, and it shuts down:  reboot and error reappears"your computer     restarted because of a problem. touch any key.....etc'  75-yr-old needs guid

    Oct 22, 2013 11:58 PM 
    downloaded 10.9  all well 'til I get desktop and can't enter my password, message of error, and it shuts down:  reboot and error reappears"your computer     restarted because of a problem. touch any key.....etc'  75-yr-old needs guidance.........running 10.8.5 til today................????????  Can run in safe boot, but what do i do now ???  thanks
    MacBook Pro, OS X Mountain Lion (10.8.3), Intel core i5 2.3GHz 

    Well, after some thought, I did a 'safe boot', did a disk verify and repair in Disk Utility, repaired permissions in DU and had the same problem I'd mentioned in post.
    SO, I went back in (safe boot.........that is, hold down start button, then 'shift') and went to applications and removed or uninstalled any apps that I thought might be interferring with the re-boot or, specifically, with my being unable to sign in with my p/w.........(at the first key stroke, it would crash and give the 'error' message)....I had both Webroot and Dashlane installed that I thought could interfere with password recognition (Webroot protects from viruses, et all and Dashlane is a password codifying appl.) I took out whatever else I thought might not be friendly and, guess what ?? When I signed out of 'safe' mode, and rebooted normally, it worked.........and has been working properly for 3-4 hrs now, so guess it's good-to-go..........seems like it...........hope this helps anyone with the same problem I'd had...........no need to visit "genius bar" some 55 miles from here............guess us mid-seventies guys ain't too old for learnin'...........G'Day, Mates !!

  • Downloaded 10.9  all well 'til I get desktop and can't enter my password, message of error, and it shuts down:  reboot and error reappears"your computer     restarted because of a problem. touch any key.....etc'

    downloaded 10.9  all well 'til I get desktop and can't enter my password, message of error, and it shuts down:  reboot and error reappears"your computer     restarted because of a problem. touch any key.....etc'  75-yr-old needs guidance.........thanx
    running 10.8.5 til today........................????????  Can run in safe boot, but what do i do now ???  thanks

    Well, after some thought, I did a 'safe boot', did a disk verify and repair in Disk Utility, repaired permissions in DU and had the same problem I'd mentioned in post.
    SO, I went back in (safe boot.........that is, hold down start button, then 'shift') and went to applications and removed or uninstalled any apps that I thought might be interferring with the re-boot or, specifically, with my being unable to sign in with my p/w.........(at the first key stroke, it would crash and give the 'error' message)....I had both Webroot and Dashlane installed that I thought could interfere with password recognition (Webroot protects from viruses, et all and Dashlane is a password codifying appl.) I took out whatever else I thought might not be friendly and, guess what ?? When I signed out of 'safe' mode, and rebooted normally, it worked.........and has been working properly for 3-4 hrs now, so guess it's good-to-go..........seems like it...........hope this helps anyone with the same problem I'd had...........no need to visit "genius bar" some 55 miles from here............guess us mid-seventies guys ain't too old for learnin'...........G'Day, Mates !!

  • SQL 2008 R2: Microsoft SQL Server Management Studio cannot shut down because a modal dialog is active. Close the active dialog and try again

    When starting SQL Server 2008 R2 it hangs , and I cannot exit...so when  trying to logoff to reset I get the following "Microsoft SQL Server Management Studio cannot shut down because a modal dialog is active. Close the active dialog and try again"Any
    ideas?

    Big edit...
    I have 2008 R2 SP2 installed on my Windows 7 Machine which is also fully updated.  The marked answer above is clearly not the solution.
    The fix I had posted before did not work.  It appeared to work temporarily, but now I am back to the same invisible dialogue.  I have not been able to identify any pattern by which this is triggered.  I can have an entire day without this
    issue and then it appears the next.
    The invisible modal dialogue is definitely the connection dialogue.  The only way out is to hit the escape key to close it, but then I am no better off without an ability to connect to a server.  The dialogue is still invisible when I re-open it.
    However, even as I type this post, I have just gotten the dialogue to appear after restarting Management Studio, hitting escape, then clicking connect again.  That same pattern failed just minutes ago numerous times.  Again, I can't find any pattern.
    See you in the clock tower.

  • Install maverik on my MacBook Pro, I had no problem. Two days later I was shut down suddenly and reboot with a closed padlock and asking me for a password that does not match any of mine. What I can do?

    Install maverik on my MacBook Pro, I had no problem. Two days later I was shut down suddenly and reboot with a closed padlock and asking me for a password that does not match any of mine. What  can I do?

    Try booting to the Recovery drive, running Disk Utility and Repair disk and Repair Permissions.
    1. Reboot and immediately hold down command and R (two keys).
    2. When you see the screen shown on this page, select Disk Utility and continue.
    3. When DU is running, select the hard drove on the left, First Aid and Repair Disk.
    4. After Repair Disk, click Repair Permissions.
    Quit DU and restart.

  • When I open email it shuts down immediately and goes back to my main screen.  Any suggestions?.

    When I open email it shuts down immediately and goes back to my main screen.  Any suggestions?.

    Double tap your home button to bring up the most recently used apps (task bar).  With your finger hold it on any of the those apps until they all start to jiggle.  Each app will now show a in the upper left corner.  Touch the minus on the Mail App to fully close it.  Touch your home button once again to stop the apps from Jiggling, then again to get back to your home screen.
    I would then Reboot your iPad:  Press and hold BOTH the power and home buttons at the SAME time for at least 10 seconds (ignore the red slider to shut down) until the Apple Logo appears, then let go of both buttons and your iPad will restart. 
    Try the mail app and see if you can navigate again.
    If neither option helps, it sometimes helps to delete the mailbox, then reinstall it.

  • I am john and I need help downloading a progmmme yesterday and wanted to finish downloading open it and I am not told me that the program was shut down unexpectedly and restart ponia not opened and went back to download it and not opened my back probe to

    i am john and I need help downloading a progmmme yesterday and wanted to finish downloading open it and I am not told me that the program was shut down unexpectedly and restart ponia not opened and went back to download it and not opened my back probe to turn off the computer and there was no case

    i am john and I need your help yesterday bought a program called DJAY when I finish the download and got an error opened and I saw him there was no case to install and thank you for your help anyway

  • HT1414 My IPHONE4 just shut down yesterday and has not come back on.

    My IPHONE4 shut down yesterdsay and will not turn back on. It was fully charged.

    Reset, hold both home and power buttons until the iPhone begins to start, usually takes about 10 seconds. If still OFF, connect to Wall Charger for 10 minutes, it may turn ON itself. If still OFF, keep on charger and Reset. It may take about 30 seconds of holding both buttons while charger. If still nothing and you have Warranty or AppleCare, make Genius reservation and take to Apple for resolution.

  • My one month old macbool pro shut down unexpectedly and is not starting up the magsafe led is faint orange and flickering what to do now???will I be charged by apple istore ??? I'm very panicked please reply

    My one month old macbool pro shut down unexpectedly and is not starting up the magsafe led is faint orange and flickering what to do now???will I be charged by apple istore ??? I'm very panicked please reply

    Welcome to Apple Support Communities
    It seems like your logic board is damaged. As your computer is in warranty, you will get your MacBook repaired for free if you take it to an Apple Store or reseller. Furthermore, you may receive a new MacBook

  • HT1338 my computer cant shut down because cant close email

    I cant shut down computer becuase , email needs to be closed I cant retrieve or close email

    Press Option + Command + Escape keys to open the Force Quit dialogue. Select Mail and Force Quit it.

  • The Cluster service is shutting down because quorum was lost

    Hi, we recently experienced the above issue and after looking for explanations I haven't been able to find any satisfying answers when other people have posted this issue.
    Our problem is as follows:
    2 node 2008R2 cluster running SQL 2012
    Each node is a HP BL460c running in a HP C7000 Blade Chassis.
    We were updating the flexfabric cards on one of the chassis.  The other chassis had been patched the previous week with no problems. 
    During the update process the flexfabric cards, which hold the Ethernet and FC connections, reboot so before work had begun all active cluster services had been failed over to the node in the chassis not being worked on.  However despite this the cluster
    service shut down on this one particular cluster.  All other clusters running across these 2 chassis continued to run as expected.
    As other people have posted before we saw the following errors in the system log.
    1564: File share witness resource 'File Share Witness' failed to arbitrate for the file share
    1069: Cluster resource 'File Share Witness' in clustered service or application 'Cluster Group' failed.
    1172: The Cluster service is shutting down because quorum was lost. This could be due to the loss of network connectivity between some or all nodes in the cluster, or a failover of the witness disk.
    Run the Validate a Configuration wizard to check your network configuration. If the condition persists, check for hardware or software errors related to the network adapter. Also check for failures in any other network components to which the node is connected
    such as hubs, switches, or bridges.
    However we cant understand what could cause this to happen when the service is running on the node in the chassis not being updated, especially when the same update was performed the week before with no issues.  How can both nodes lose connectivity
    to the File Share Witness at the same time?
    Cluster Validation tests run fine and don't highlight any issues.  The file share witness is accessible from both servers.

    Hi,
    Please confirm you have install the Recommended hotfixes and updates for Windows Server 2008 R2 SP1 Failover Clusters update, especially the following hotfix.
    The network location profile changes from "Domain" to "Public" in Windows 7 or in Windows Server 2008 R2
    http://support.microsoft.com/kb/2524478/EN-US
    A hotfix is available that adds two new cluster control codes to help you determine which cluster node is blocking a GUM update in Windows Server 2008 R2 and Windows Server
    2012
    http://support.microsoft.com/kb/2779069/EN-US
    Hope this helps.
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • I tried downloading the iOS8 to my iPod 5th generation and when it finished downloading it shut down completely and it said there was an error and no the iPod is in recovery mode. What can I do to restore it and update it? Please, I need help.

    Hello,
    I recently tried downloading the IOS8 to my iPod 5th generation and when it was almost done the computer said there was an error. Right after that, the iPod shut down completely and now it's on recovery mode. I plugged it in and it said that I had to restore it and update it so I could use it again but it doesn't let me. What can I do? I even did a backup before the update.
    I really need help.

    What happens when you connect to computer and restore via iTunes?
    Without knowing that:
    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

Maybe you are looking for

  • R12: How to filter Open Item Revaluation Report based on GL Date

    Hi, Anybody know how to filter Open Item Revaluation Report based on GL Date from and GL Date to in R12? Since we just upgraded from 11.5.10 to 12.1.3 and found we cannot filter those report for specific date. It shown all data included the old data

  • Apple TV error message HDMI doesn't support HDCP

    Apple TV error message HDMI doesn't support HDCP

  • Iphone 4 apps problem

    Hi folks I have a problem with my iphone4. If I download apps from the app store they look bad. And when I put them on my iPod Touch (1st generation nation) they look geat. Please help me

  • Jsf 2.0 functionality in Jsf 1.2

    Hi Team, I am using Jdev version 11.1.1.7 so JSF Version : JSF 1.2 I need to use the functionality which presents in the JSF 2.0. i.e., FacesContext.getAttributes() and UIViewRoot.getViewRoot() Any suggestions how to achieve the above functionalityin

  • Reg: Material Ledger Account posting

    Hello Everyone, We have Material Ledger active for a plant with transaction based price determination (Price Control V). I have posted a GR & its creating 2 Accounting docs. One with Transaction keys BSX, WRX & PRD. WRX is calculating correctly based