I got a flashing folder with a question mark. I got a new hard drive and upgraded to 4 gigs and can't open anything or reload the operating system? Help?

I got a flashing folder with a question mark. I got a new hard drive and upgraded to 4 gigs and can't open anything or reload the operating system? Help? FYI: I have been using boot camp with windows 7 and started getting a kernal_data_Page_error and it would reboot windows, i was trying to do a chkdsk on the next reboot, but thats when i started getting this issue. I have put in a new hard drive and went from 2 gigs to 4. I can not get the computer to do anything, even the monitor does not show anything now????

Prep your new drive:
Drive Preparation
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs,) then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
After formatting has completed quit DU and return to the installer. Install OS X.

Similar Messages

Getting a flashing folder with a question mark when starting Imac.

I got this flashing folder with a question mark on it when starting my Imac this morning. Im running on Osx 10.6. I put it in target disc mode and connected it to my macbook pro. I opened the disc utility app on the macbook and found my imac. I "verified" it and found an error. When I clicked "repair" the disc utility app froze and crashed. When I opened it again my Imac didn't show up. I've restarted both computers several times with no luck. Whats my next step?

Hi.
Try restarting your iMac while holding down the option (alt) key until the spinng gear appears. You should momentarily be presented with a list of startup drives to select.
Choose Macintosh HD (your normal startup disk drive) and click the right-arrow.
When your iMac boots, go to System Preferences > Startup Disk and again select your normal startup disk. Then click Restart.
I hope this is helpful.
EDIT - disconnect the machines from each other first.

MacBook Pro gets a flashing folder with a question mark

I start up my computer and I get this flashing folder with a question mark. I looked up on here how to fix it but I get lost when I get to the disk utility part. All that shows up is something called disk0 and below it it says Mac OS X Base System. I click on it but the repair disk button is greyed out. What do I do? Please help!

The MBP cannot find the OSX. It may be a HDD or HDD connection problem.
Start your MBP with the OPTION key down. Select the recovery partition. From the 4 option menu select Disk Utility.
Select Disk Utility>First Aid and run Verify and Repair.
If successful, you should be back in business. If not, the HDD may be faulty.
Ciao.

On a macbook I purchased secondhand hard drive got corrupted and I started to get the flashing folder with the question mark, I purchased a new hard drive and snow lion install DVD I installed the hard drive and tried disc but kept getting blinking folder

On a macbook I purchased secondhand hard drive got corrupted and I started to get the flashing folder with the question mark, I purchased a new hard drive and snow lion install DVD I installed the hard drive and tried disc but kept getting blinking folder

Welcome to Apple Support Communities. We're users here and do not speak for "Apple Inc."
Power on the computer and insert the DVD immediately.
Hold down the 'C' key to boot from the Snow Leopard DVD.
http://support.apple.com/kb/ht1533
After selecting the appropriate language, if necessary, select Utilities, and Disk Utility.
You'll likely need to partition and format the new drive before it's recognized.
http://manuals.info.apple.com/MANUALS/0/MA161/en_US/MacBook_13inch_HardDrive_DIY .pdf
(Yes, these instructions ARE 7 years old, but the procedure is the same for installing from DVD media.)

When i boot i get a flashing folder with a question mark. disk utility doesnt work or read my harddrives to boot with. i installed a new SSD and its not reading that either. i have a macbook pro 2011, any help?

So I came to this problem a while ago. M ycomputer basically froze so I was forced to shut down by holding the button down. When I started it up I got the flashing folder with a question mark. I started it up holding down the command and r keys which brought me to disk utility. Although my computer doesn't read that I have a hard drive to start it up. When I click on the disk utility app, I cannot verify or repair anything either. The buttons won't allow me to click on them. It also shows "Mac OSX Base System" which shows I have files and what not saved. I had been told that I need a new hard drive so I bought and manually installed a OWC SSD 240GB drive and when i booted the computer up it booted up yo the operating system fine with all my files and what not on there. After about twenty minutes, it froze again. I forced a shut down, restarted and the same thing happened. I am not able to choose my SSD to boot up, although thats probably because it doesn't have an operating system installed on it??
i have a Macbook Pro 13" 2011
any help would be great, I'm overall confused.

ryansaint11,
this isn’t Apple support; this is a user-to-user forum. We’re just fellow users of Apple products here.
If you want to boot from your SSD, then you should put the SSD where your HDD currently is, and put the HDD into the optical bay. (That setup will also get you the best performance.) At the moment, you’re still booting from your HDD. Note that you will need to format your SSD in Disk Utility [with the “Mac OS X Extended (Journaled)” format] so that you can install OS X onto it.
Since you have an Early 2011 model, it might or might not have originally come with grey installation DVDs. You will be able to find out whether it did or not by trying to use OS X Internet Recovery to install OS X onto your SSD. If it does not work, or if the installed OS turns out to be Snow Leopard, then it will have originally come with the DVDs, and you should purchase a replacement pair of DVDs from Apple or iFixit; those discs will have your MacBook Pro’s Apple Hardware Test and its iLife apps. If the installed OS turns out to be Lion, then it will not originally have come with the grey installation DVDs, and your Apple Hardware Test will be installed along with Lion, and your iLife apps will be downloadable from the Mac App Store.

My new mac mini (3 month) didn't start up,all that appeared was a white screen and a flashing folder with a question mark inside it.

My new Mac mini (3 month) didn't start up, all that appeared was a white screen and a flashing folder with a question mark inside it.
I followed by recommendations from 'Everything Mac': "shut it down by pressing and holding the power button for about 5 seconds.
Then hold down the Option key and press the power button again to start up the Mac mini. Keep holding down the Option key until
the Mac mini starts up."
But I got a Wi-Fi button only to chose and connect the local network. I connected to my network and I can't use this connection
becouse no icons.
Could you please help me?

Your Mini (running 10.6.4) should have come with grey-colored install disks. Now is the time to put them into service. Turn on your computer so that there is power to accept disk #1 into the optical drive. Once the disk is in the drive, shut off the computer by holding the start button down until it powers off. Then turn it on this time holding down the "C" key to make the computer boot from the disk. The question mark that you saw indicates that the computer cannot find a bootable volume. This can happen due to corrupted system files or an improper shutdown etc. Once you are in the "Installer" you can choose Disk Utility from the Utilities Menu in the menu bar. Use it to repair the disk and to see if that can solve your trouble.

Have a flashing folder with a question mark on start-up but cannot hold option as wireless keyboard won't connect, how do I get it to connect if I cannot turn on the machine?

Hello all, I've registered here because I can't work out how to get my keyboard and mouse to connect.
The issue is that when I turn my mid-2010 iMac on it doesn't load up, but instead shows a flashing folder with a question mark. I've Googled this and have some idea how to fix it, the first step in all guides to fixing the problem states that you should hold the option key upon start-up. The problem I'm having is that I've just had to change the batteries on my keyboard and mouse and they are now not connecting. I can't see how to get the keyboard and mouse connected with the Mac stuck on the flashing folder screen, and I can't get the Mac past said screen without using the keyboard. Does anyone know how I can connect the two devices?
Thanks.

The flashing folder with the ? mark indicates that a bootable system can't be found. You'll need to borrow a wired keyboard so you can boot into the Recovery volume (boot with the Command + R keys held down). From there you can reinstall the system and try a normal reboot.

HT1310 when i starst my mac i get a flashing folder with a question mark. i tried rebooting and holding the option button then i get 2 boxes, one with a refresh arrow and one with a forward arrow neither of them seem to do anything. now what

when i starst my mac i get a flashing folder with a question mark. i tried rebooting and holding the option button then i get 2 boxes, one with a refresh arrow and one with a forward arrow neither of them seem to do anything. now what

Here is an article that describes what it is supposed to do:
Startup Manager: How to select a startup volume
If no Volumes are shown, it is telling you there are no potentailly bootable Volumes attached. That means your boot drive has died or the bootable image on it is unrecognizable.
What Mac Pro ? by year, GHz, number of processors, screen size?
What Mac OS X ?

When I start my Mac air I get a flashing folder with a question mark

I am trying to start my Mac air and I get a flashing folder with a question mark. When I turn the power of it shuts down but wen starting it comes back

Just being clear about your situation. When you hold down Option during boot it does not show a system volume or a recovery volume from which to boot. At that point if you select a network boot and you do not see a spinning globe that persists there a good while as it loads the recovery partition over the network. True?
A couple of more thinks to try:
Disconnect all of your external devices.
Reset PRAM
Boot with the option key again.
Standard things to try (which is sounds like you already have attempted) A flashing question mark appears when you start your Mac

I just powered on my mac book pro and have a blue screen with a flashing folder with a question mark in the middle, how do I get out of this?

I just booted my mac book pro and it is at a blue screen with a flashing folder with a question mark in the middle of it. How do I get out of it?

Click here and follow the instructions. If the computer was running Mac OS X 10.6.8 or earlier and you reach the third set of steps, insert a Mac OS X install disk.
(126818)

Flashing folder with a question mark in it when starting up

Hi, I own a white MacBook that is fairly new. When I boot it there is a flashing folder with a question mark in it. I read here: http://support.apple.com/kb/TS1440 what to do.
I inserted my Leopard disc, held C while booting and then opened Disc Utilitiy. But the only images to appear in the left column of Disc Utility is the "Mac OS X Install DVD". So I tried resetting the PRAM by holding down cmd-opt-R-P while booting.
Then I tried the same thing again but still there is only the install disc in the left column. If I go to Startup Disc there is only the install CD and "Network Startup".
Now, if I were to reinstall the system as it says in step 4 of the guide, what will happen to my data? I read that this error could be a sign of the hard drive crashing, and with no back up I really don't want that to happen.
So, is it safe to reinstall the system, or what do you suggest my next step to be?

Try booting in Safe Mode
http://support.apple.com/kb/HT1455
Resolve startup issues and perform disk maintenance with Disk Utility and fsck
I tried booting in Safe Mode by holding down shift while starting, but it just went to the flashing folder with the ?-mark in it. Then I tried to enter single-user mode by holding down cmd-S while starting (http://support.apple.com/kb/HT1492), in order to try the fsck-thingy, but still just the flashing ?.
When I start my computer it makes bad noises from the bottom right side. I fear that the HD is broken , it sounds as if it is working very hard, making scratchy and clicky noises.
I also tried using the computer as a FireWire target in order to retrieve some data (http://support.apple.com/kb/HT1661). When I bootet the "broken" computer and held down T the FireWire symbol appeared on the screen. But on the host computer I could not find the target computer.
Any more ideas?

Trying to take computer back to factory specs and now I get this message a flashing folder with a question mark

Trying to take computer back to factory specs and now I am gettin a flashing folder with a question mark on it

The flashing folder means the computer is unable to find a valid boot disk. If you booted into the Recovery Drive using Command R and formatted the drive you must also download and install the operating system. Have you done that? If not, reboot using Command R and do so.

What do I do when he only thing on my screen is a flashing folder with a question mark.

I had a few browsers open on my computer. I accessed my calendar and it froze. The mouse would still move, but I could not click on anything. Then the screen went grey with a flashing folder with a question mark. I turned the power off and turned it back only but only see the grey screen with the flashing folder. I tried resetting the PRAM but it still will not work. Can this be fixed? Please help!!

You may have a disk error - could be an unrepairable physical problem with the drive, or a repairable file structure problem.
Hold down cmd-R (both keys together) as you start up the Mac, and keep them held down until you see the Apple menu. When it boots to the recovery partition, click Disk Utility, and run Repair Disk on the Macintosh HD. Let us know if you see errors there and whether or not DU can fix them.
Good luck!
Matt

What does it mean when i have a flashing folder with a question mark in it when i try to boot up?

what does it mean when I have a flashing folder with a question mark in the middle of it when I try to boot the interface?

It means the system cannot find a bootable OS. Reinstall OS X.
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

When I boot up my I get a grey screen with a flashing folder with a question mark

I was trying to set up a bootable Linux flash drive for another computer using UNetbootin and I accidentally selected an empty partition on my hard drive instead of the USB I was trying to use. It went through the install process, and I didn't realize it was on my computer rather than the USB. The computer worked fine, so I thought nothing of it.
Today, I go to mess with my computer and it is frozen at the login screen. I restart it, and now I just get a blinking folder with a question mark. I try to go into recovery, but it isn't there. Internet Recovery works fine, but when I go to use Disk Utility or to reinstall the OS it cannot find the internal Hard Disk.
What am I supposed to do here? I don't want to lose all my data.

greenbil1
You can contact AppleCare to buy a replacement set of the oringinal Install discs for a nominal cost. You will need the serial number and a credit card to place the order.

I got a flashing folder with a question mark. I got a new hard drive and upgraded to 4 gigs and can't open anything or reload the operating system? Help?

Similar Messages

Maybe you are looking for